EXEC Mode Commands


Use the EXEC mode for setting, viewing, and testing system operations. In general, the user EXEC commands allow you to connect to remote devices, change terminal line settings on a temporary basis, perform basic tests, and list system information.

The EXEC mode is divided into two access levels: user and privileged.

The user EXEC mode is used by local and general system administrators, while the privileged EXEC mode is used by the root administrator. Use the enable and disable commands to switch between the two levels. Access to the user-level EXEC command line requires a valid password.

The user-level EXEC commands are a subset of the privileged-level EXEC commands. The user-level EXEC prompt is the hostname followed by a right angle bracket (>). The prompt for the privileged-level EXEC command line is the pound sign (#). To execute an EXEC command, enter the command at the EXEC system prompt and press the Return key.


Note You can change the hostname using the hostname global configuration command.


The following example shows how to access the privileged-level EXEC command line from the user level:

WAE> enable
WAE#

To leave EXEC mode, use the exit command at the system prompt:

WAE# exit
WAE>


cd

To change from one directory to another directory in the WAAS software, use the cd EXEC command.

cd directoryname

Syntax Description

directoryname

Directory name.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use this command to navigate between directories and for file management. The directory name becomes the default prefix for all relative paths. Relative paths do not begin with a slash (/). Absolute paths begin with a slash (/).

Examples

The following example shows how to change to a directory using a relative path:

WAE(config)# cd local1

The following example shows how to change to a directory using an absolute path:

WAE(config)# cd /local1

Related Commands

deltree

dir

lls

ls

mkdir

pwd

cifs

To control legacy CIFS adapter operations and run-time configurations, use the cifs EXEC command.

cifs auto-discovery {disable | enable | reset-log}

cifs mss value

cifs restart [core | edge]

cifs reverse-dns {active | disable | enable}

cifs session disconnect [client-ip ipaddress | server-ip ipaddress]

Syntax Description

auto-discovery

Controls the CIFS auto-discovery configuration and debug.

disable

Disables the CIFS server operation.

enable

Enables the CIFS server operation.

reset-log

Resets the log memory.

mss value

Sets the TCP maximum segment size (MSS) for the CIFS adapter. This value must be an integer in the range of 512-1460.

restart

Restarts the CIFS application.

core

(Optional) Restarts the CIFS application on the Core WAE.

edge

(Optional) Restarts the CIFS application on the Edge WAE.

reverse-dns

Uses reverse DNS to resolve server names on the Core WAE.

active

Checks whether reverse DNS is active.

session

Configures operations on active CIFS sessions.

disconnect

Disconnects the CIFS sessions.

client-ip ipaddress

Sets the client IP address or address set.

server-ip ipaddress

Sets the server IP address or address set.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

This command controls legacy mode CIFS. To control the transparent CIFS accelerator, use the (config) accelerator cifs command. These two modes are mutually exclusive. For more information on the two WAFS modes, see the chapter "Configuring Wide Area File Services" in the Cisco Wide Area Application Services Configuration Guide.

Use the cifs restart command to restart the WAFS services for a configuration change without having to reboot the WAE.

Examples

The following example shows how to set the TCP maximum segment size (MSS) value to 512 for the CIFS adapter:

WAE# cifs mss 512

Related Commands

show cifs

show statistics cifs

clear arp-cache

To clear the ARP cache, use the clear arp-cache EXEC command.

clear arp-cache [ipaddress | interface {GigabitEthernet 1-2/port | PortChannel 1-2 | Standby 1}]

Syntax Description

arp-cache

Clears the ARP cache.

ipaddress

(Optional) ARP entries for the IP address.

interface

(Optional) Clears all ARP entries on the interface.

GigabitEthernet 1-2/port

GigabitEthernet interface (slot/port).

PortChannel 1-2

PortChannel interface number. Values are 1 or 2

Standby 1

Standby interface number 1.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the ARP cache on the WAAS device:

WAE# clear arp-cache

Related Commands

license add

show interface

show license

show wccp

clear cache

To clear cached objects, use the clear cache EXEC command.

clear cache {cifs | dre}

Syntax Description

cifs

Clears the CIFS cache.

dre

Clears the DRE cache.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

After you use the clear cache dre command, the first 1 MB of data is not optimized. The Cisco WAAS software does not optimize the first 1 MB of data after a restart of the tcpproxy service. The data that is transmitted after the first 1 MB of data will be optimized according to the configured policy.

Examples

The following example shows how to clear the CIFS cached objects on the WAAS device:

WAE# clear cache cifs

Related Commands

license add

show interface

show license

show wccp

clear cdp

To clear Cisco Discovery Protocol statistics, use the clear cdp EXEC command.

clear cdp {counters | table}

Syntax Description

cdp

Resets the Cisco Discovery Protocol (CDP) statistical data.

counters

Clears the CDP counters.

table

Clears the CDP tables.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the CDP counter statistics on the WAAS device:

WAE# clear cdp counters

Related Commands

license add

show interface

show license

show wccp

clear ip

To clear IP access list statistics, use the clear ip EXEC command.

clear ip access-list counters [acl-num | acl-name]

Syntax Description

ip

Clears the IP statistical information.

access-list

Clears the access list statistical information.

counters

Clears the IP access list counters.

acl-num

(Optional) Clears the counters for the specified access list, identified using a numeric identifier (standard access list: 1-99; extended access list: 100-199).

acl-name

(Optional) Clears the counters for the specified access list, identified using an alphanumeric identifier of up to 30 characters, beginning with a letter.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the IP access list counters on the WAAS device:

WAE# clear ip access-list counters

Related Commands

license add

show interface

show license

show wccp

clear license

To clear licensing configuration, use the clear license EXEC command.

clear license [license-name]

Syntax Description

license

Removes all installed software licenses, when specified without options.

license-name

Name of the software license to remove. The following license names are supported:

Transport—Enables basic DRE, TFO, and LZ optimization.

Enterprise—Enables the EPM, HTTP, MAPI, NFS, SSL, CIFS (WAFS), and Windows Print application accelerators, the WAAS Central Manager, and basic DRE, TFO, and LZ optimization. You cannot remove this license if the video or virtualization licenses are installed. You must remove both of those licenses first.

Video—Enables the video application accelerator.

Virtual-Blade—Enables the virtualization feature.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the licensing configuration on the WAAS device:

WAE# clear license

Related Commands

license add

show interface

show license

show wccp

clear logging

To clear syslog messages saved in a disk file, use the clear logging EXEC command.

clear logging

Syntax Description

logging

Clears the syslog messages saved in the disk file.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear logging command removes all current entries from the syslog.txt file but does not make an archive of the file. It puts a "Syslog cleared" message in the syslog.txt file to indicate that the syslog has been cleared.

Examples

The following example shows how to clear all entries in the syslog.txt file on the WAAS device:

WAE# clear logging

Feb 14 12:17:18 WAE# exec_clear_logging:Syslog cleared

Related Commands

license add

show interface

show license

show wccp

clear statistics

To reset statistics data, use the clear statistics EXEC command.

clear statistics {all | aoim | authentication | auto-discovery {all | blacklist}| datamover | directed-mode | dre [global] | filtering | flow monitor tcpstat-v1 | generic-gre | icmp | inline | ip | pass-through | peer dre | radius | synq | tacacs | tcp | tfo | udp | wccp | windows-domain | windows-print}

Syntax Description

all

Clears all statistics.

authentication

Clears authentication statistics.

auto-discovery

Clears the auto-discovery statistics.

all

Clears all of the auto-discovery statistics.

aoim

Clears all of the application accelerator information manager statistics.

blacklist

Clears the auto-discovery statistics for the blacklist.

datamover

Clears all of the data mover statistics.

directed-mode

Clears the directed mode statistics.

dre

Clears the Data Redundancy Elimination (DRE) statistics.

global

Clears the global DRE statistics.

filtering

Clears the filter table statistics.

flow

Clears the network traffic flow statistics.

monitor

Clears the monitor flow performance statistics.

tcpstat-v1

Clears the tcpstat-v1 collector statistics.

generic-gre

Clears the generic GRE statistics.

icmp

Clears the ICMP statistics.

inline

Clears the inline interception statistics.

ip

Clears the IP statistics.

pass-through

Clears all of the pass-through statistics.

peer dre

Clears all peer DRE statistics.

radius

Clears the RADIUS statistics.

synq

Clears the SynQ module statistics.

tacacs

Clears the TACACS+ statistics.

tcp

Clears the TCP statistics.

tfo

Clears the TCP flow optimization (TFO) statistics.

udp

Clears the UDP statistics.

wccp

Clears all of the WCCP statistics.

windows-domain

Clears the Windows domain statistics.

windows-print

Clears all of the Windows print statistics.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear statistics command clears all statistical counters from the parameters given. Use this command to monitor fresh statistical data for some or all features without losing cached objects or configurations.

Not all command options are applicable for a device in central-manager mode.

Examples

The following example shows how to clear all authentication, RADIUS and TACACS+ information on the WAAS device:

WAE# clear statistics radius
WAE# clear statistics tacacs
WAE# clear statistics authentication

Related Commands

clear statistics accelerator

clear statistics connection

clear statistics accelerator

To clear all global statistics, use the clear statistics accelerator EXEC command.

clear statistics accelerator {cifs | epm | generic | http | mapi | nfs | ssl | video}

Syntax Description

cifs

Clears the statistics for the CIFS application accelerator.

epm

Clears the statistics for the EPM application accelerator.

generic

Clears the statistics for generic accelerator.

http

Clears the statistics for the HTTP application accelerator.

mapi

Clears the statistics for the MAPI application accelerator.

nfs

Clears the statistics for the NFS application accelerator.

ssl

Clears the statistics for the SSL application accelerator.

video

Clears the statistics for the video application accelerator.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to clear the statistics for the CIFS application accelerator on the WAAS device:

WAE# clear statistics accelerator cifs

Related Commands

clear statistics

clear statistics connection

clear statistics connection

To clear connection statistics, use the clear statistics connection EXEC command.

clear statistics connection conn-id connection_id

clear statistics connection optimized [client-ip {ip_address | hostname} | client-port port | {cifs | epm | http | mapi | nfs | ssl | tfo | video} dre | peer-id peer_id | server-ip {ip_address | hostname} | server-port port]

Syntax Description

conn-id connection_id

Clears connection statistics for the connection with the specified number identifier.

optimized

Clears connection statistics for optimized connections.

client-ip

(Optional) Clears connection statistics for the client with the specified IP address or hostname.

ip_address

IP address of a client or server.

hostname

Hostname of a client or server.

client-port port

(Optional) Clears the connection statistics for the client with the specified port number. Port number 1-65535.

cifs

(Optional) Clears connection statistics for connections optimized by the CIFS application accelerator.

epm

(Optional) Clears connection statistics for connections optimized by the EPM application accelerator.

http

(Optional) Clears connection statistics for connections optimized by the HTTP application accelerator.

mapi

(Optional) Clears connection statistics for connections optimized by the MAPI application accelerator.

nfs

(Optional) Clears connection statistics for connections optimized by the NFS application accelerator.

ssl

(Optional) Clears connection statistics for connections optimized by the SSL application accelerator.

tfo

(Optional) Clears connection statistics for connections optimized by the TFO application accelerator.

video

(Optional) Clears connection statistics for connections optimized by the video application accelerator.

dre

(Optional) Clears connection statistics for connections optimized by the DRE feature.

peer-id peer_id

(Optional) Clears the connection statistics for the peer with the specified identifier. Number from 0 to 4294967295 identifying a peer.

server-ip

(Optional) Clears the connection statistics for the server with the specified IP address or hostname.

server-port port

(Optional) Clears the connection statistics for the server with the specified port number. Port number 1-65535.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to clear the connection 1 statistics on the WAAS device:

WAE# clear statistics connection conn-id 1

Related Commands

clear statistics

clear statistics accelerator

clear transaction-log

To archive working transaction log file, use the clear transaction-log EXEC command.

clear transaction-log {flow}

Syntax Description

transaction-log

Clears the transaction log.

flow

Clears the TFO transaction log.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to archive the flow transaction log file on the WAAS device:

WAE# clear transaction-log flow

Related Commands

license add

show interface

show license

show wccp

clear users

To clear user connections or to unlock users that have been locked out, use the clear users EXEC command.

clear users [administrative | locked-out {all | username username}]

Syntax Description

users

Clears the connections (logins) of authenticated users.

administrative

(Optional) Clears the connections (logins) of administrative users authenticated through a remote login service.

locked-out

(Optional) Unlocks specified locked-out user accounts.

all

Specifies all user accounts.

username username

Specifies account username.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear users administrative command clears the connections for all administrative users who are authenticated through a remote login service, such as TACACS. This command does not affect an administrative user who is authenticated through the local database.

The clear users locked-out command unlocks user accounts that have been locked out. If a strong password policy is enabled (see the (config) authentication strict-password-policy command) a user account will be locked out if the user fails three consecutive login attempts. (This restriction does not apply to the admin account.)

Examples

The following example shows how to clear the connections of all authenticated users:

WAE(config)# clear users

The following example shows how to clear the connections of all administrative users authenticated through a remote login service (it does not affect administrative users authenticated through the local database):

WAE(config)# clear users administrative

The following example shows how to unlock all locked-out user accounts:

WAE(config)# clear users locked-out all

The following example shows how to unlock the account for username darcy:

WAE(config)# clear users locked-out username darcy

Related Commands

clear arp-cache

(config) authentication strict-password-policy

clear windows-domain-log

To clear the Windows domain server log file, use the clear windows-domain-log EXEC command.

clear windows-domain-log

Syntax Description

windows-domain-log

Clears the Samba, Kerberos, and Winbind log files.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear all entries in the Windows domain log file on the WAAS device:

WAE# clear windows-domain-log

Related Commands

license add

show interface

show license

show wccp

clock

To set clock functions or update the calendar, use the clock EXEC command.

clock {read-calendar | set time day month year | update-calendar}

Syntax Description

read-calendar

Reads the calendar and updates the system clock.

set time day month year

Sets the time and date. Current time in hh:mm:ss format (hh: 00-23; mm: 00-59; ss: 00-59). Day of the month (1-31). Month of the year (January, February, March, April, May, June, July, August, September, October, November, December). Year (1993-2035).

update-calendar

Updates the calendar with the system clock.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If you have an outside source on your network that provides time services (such as a NTP server), you do not need to set the system clock manually. When setting the clock, enter the local time. The WAAS device calculates the UTC based on the time zone set by the clock timezone global configuration command.

Two clocks exist in the system: the software clock and the hardware clock. The software uses the software clock. The hardware clock is used only at bootup to initialize the software clock.

The set keyword sets the software clock.

Examples

The following example shows how to set the software clock on the WAAS device:

WAE# clock set 13:32:00 01 February 2005

Related Commands

show clock

cms

To configure the Centralized Management System (CMS) embedded database parameters for a WAAS device, use the cms EXEC command.

cms {config-sync | deregister [force] | lcm {enable | disable} | maintenance {full | regular} | recover {identity word} | restore filename | validate}

cms database {backup | create | delete | downgrade [script filename]}

Syntax Description

config-sync

Sets the node to synchronize configuration with the WAAS Central Manager.

deregister

Removes the device registration record and its configuration on the WAAS Central Manager.

force

(Optional) Forces the removal of the node registration. This option is available only on WAEs and the standby Central Manager. If disk encryption is enabled, it is disabled and encrypted file systems are erased after a reload.

lcm

Configures local/central management on a WAAS device that is registered with the WAAS Central Manager.

enable

Enables synchronization of the WAAS network configuration of the device with the local CLI configuration.

disable

Disables synchronization of the WAAS network configuration of the device with the local CLI configuration.

maintenance

Cleans and reindexes the embedded database tables.

full

Specifies a full maintenance routine for the embedded database tables.

regular

Specifies a regular maintenance routine for the embedded database tables.

recover

Recovers the identity of a WAAS device.

identity word

Specifies the identity of the recovered device (identification key set on the Central Manager)

restore filename

Restores the database management tables using the backup local filename.

validate

Validates the database files.

database

Creates, backs up, deletes, restores, or validates the CMS-embedded database management tables or files.

backup

Backs up the database management tables.

create

Creates the embedded database management tables.

delete

Deletes the embedded database files.

downgrade

Downgrades the CMS database.

script filename

(Optional) Downgrades the CMS database by applying a downgrade script (filename).


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the cms config-sync command to enable registered WAAS devices and standby WAAS Central Manager to contact the primary WAAS Central Manager immediately for a getUpdate (get configuration poll) request before the default polling interval of 5 minutes. For example, when a node is registered with the primary WAAS Central Manager and activated, it appears as Pending in the WAAS Central Manager GUI until it sends a getUpdate request. The cms config-sync command causes the registered node to send a getUpdate request at once, and the status of the node changes as Online.

Use the cms database create command to initialize the CMS database for a device that is already registered with the WAAS Central Manager. Then use the cms enable command to enable the CMS. For a device that is not registered with a WAAS Central Manager, use only the cms enable command to initialize the CMS database tables, register the node, and enable the CMS.

Before a node can join a WAAS network, it must first be registered and then activated. Activate the node by using the WAAS Central Manager GUI.

The cms deregister command removes the node from the WAAS network by deleting registration information and database tables.

The cms deregister force command forces the removal of the node from the WAAS network by deleting registration information and database tables. If disk encryption is enabled on the device, it is disabled after you confirm this action. All data in encrypted file systems and imported certificates and private keys for the SSL accelerator are lost after a reload.

To back up the existing management database for the WAAS Central Manager, use the cms database backup command. For database backups, specify the following items:

Location, password, and user ID

Dump format in PostgreSQL plain text syntax

The naming convention for backup files includes the time stamp and the WAAS version number.


Note For information on the procedure to back up and restore the CMS database on the WAAS Central Manager, see the Cisco Wide Area Application Services Configuration Guide.



Note Do not run multiple instances of the cms database backup command simultaneously on a device. If a backup is in progress, you must wait for it to finish before using the command again.


When you use the cms recover identity word command when recovering lost registration information, or replacing a failed node with a new node that has the same registration information, you must specify the device recovery key that you configured in the Modifying Config Property, System.device.recovery.key window of the WAAS Central Manager GUI.

Use the lcm command to configure local/central management (LCM) on a WAE. The LCM feature allows settings that are configured using the device CLI or GUI to be stored as part of the WAAS network-wide configuration data (enable or disable).

When you enter the cms lcm enable command, the CMS process running on WAEs and the standby WAAS Central Manager detects the configuration changes that you made on these devices using CLIs and sends the changes to the primary WAAS Central Manager.

When you enter the cms lcm disable command, the CMS process running on the WAEs and the standby WAAS Central Manager does not send the CLI changes to the primary WAAS Central Manager. Settings configured using the device CLIs will not be sent to the primary WAAS Central Manager.

If LCM is disabled, the settings configured through the WAAS Central Manager GUI will overwrite the settings configured from the WAEs; however, this rule applies only to those local device settings that have been overwritten by the WAAS Central Manager when you have configured the local device settings. If you (as the local CLI user) change the local device settings after the particular configuration has been overwritten by the WAAS Central Manager, the local device configuration will be applicable until the WAAS Central Manager requests a full device statistics update from the WAEs (clicking the Force full database update button from the Device Dashboard window of the WAAS Central Manager GUI triggers a full update). When the WAAS Central Manager requests a full update from the device, the WAAS Central Manager settings will overwrite the local device settings.

Examples

The following example shows how to back up the cms database management tables on the WAAS Central Manager named waas-cm:

waas-cm# cms database backup 
creating backup file with label `backup'
backup file local1/acns-db-9-22-2002-17-36.dump is ready. use `copy' commands to move the 
backup file to a remote host.

The following example shows how to validate the cms database management tables on the WAAS Central Manager named waas-cm:

waas-cm# cms database validate 
Management tables are valid

Related Commands

(config) cms

show cms

cms secure-store

To configure secure store encryption, use the cms secure-store EXEC commands.

cms secure-store {init | open | change | clear | reset}

Syntax Description

init

Initializes secure store encryption on the WAAS device and opens the secure store.

On the Central Manager, this command prompts you to enter the secure store encryption pass phrase.

open

Activates secure store encryption (the WAAS device encrypts the stored data using secure store encryption). Secure store encryption must already be initialized using the cms secure-store init command.

On the Central Manager, this command prompts you to enter the secure store encryption pass phrase.

change

Changes the secure store encryption pass phrase and encryption key. On the Central Manager this command prompts you to enter the current pass phrase, new pass phrase, and confirm the new pass phrase. The WAAS device uses the pass phrase to generate the encryption key for secure disk encryption.

clear

Disables secure store encryption.

reset

Resets secure store to the uninitialized state. Secure store encryption must be initialized but not open to use this option. This option applies only to a Central Manager device.


Defaults

The standard encryption and key management is the default.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Secure store encryption provides stronger encryption and key management for your WAAS system. The WAAS Central Manager and WAE devices use secure store encryption for handling passwords, managing encryption keys, and for data encryption.

When you use the cms secure-store EXEC command to enable secure store on the Central Manager, or a WAE device, the WAAS system uses strong encryption algorithms and key management policies to protect certain data on the system. This data includes encryption keys used by applications in the WAAS system, CIFS passwords, and user login passwords.

When you enable secure store on Central Manager, the data is encrypted using a key encryption key generated from the pass phrase you enter with SHA-1 hashing and an AES 256-bit algorithm. When you enable secure store on a WAE device, the data is encrypted using a 256-bit key encryption key generated by SecureRandom, a cryptographically strong pseudorandom number. You must enter a password to enable secure store. The password must conform to the following rules:

Be 8 to 64 characters in length

Contain characters only from the allowed set ([A-Za-z0-9~%'!#$^&*()|;:,\"<>/]*)

Contain at least one digit

Contain at least one lowercase and one uppercase letter

When you first initialize secure store encryption with the cms secure-store init command, this command also opens the secure store, so there is no need to use the cms secure-store open command. When you reboot the Central Manager, you must manually reopen secure store using the cms secure-store open command. Until you open the secure store, a critical alarm is displayed on the Central Manager.

When you enable secure store on a WAE, the WAE initializes and retrieves a new encryption key from the Central Manager. The WAE uses this key to encrypt user passwords, CIFS preposition and dynamic share credentials, and WAFS password credentials stored on the WAE. When you reboot the WAE after enabling secure store, the WAE retrieves the key from the Central Manager automatically, allowing normal access to the data that is stored in the WAAS persistent storage. If key retrieval fails, an alarm is raised and secure store will be in the initialized but not open state. You must open secure store manually.

If you have made any other CLI configuration changes on a WAE within the datafeed poll rate time interval (5 minutes by default) before you entered the cms secure-store command, you will lose those prior configuration changes and you will need to redo them.

Use the cms secure-store reset command if you reload the Central Manager and forget the secure store password, so you cannot open the secure store. This command deletes all encrypted data, certificate and key files, and key manager keys. The secure store is left in the uninitialized state. For the complete procedure for resetting the secure store, see the "Resetting Secure Store Encryption on a Central Manager" section on page 9-15 in the Cisco Wide Area Application Services Configuration Guide.

Examples

The following example shows how to initialize and activate secure store encryption on the WAAS Central Manager:

waas-cm# cms secure-store init
Stopping cms.
 
*******************************************************************
* 1) Must be between 8 to 64 characters in length                 *
* 2) Allowed character set is ([A-Za-z0-9~%'!#$^&*()|;:,"<>/]*)   *
* 3) Must contain at least one digit                              *
* 4) Must contain at least one lowercase and one uppercase letter *
*******************************************************************
 
enter pass-phrase:
confirm pass-phrase:
Successfully migrated user passwords
Successfully migrated Cifs preposition password
Successfully migrated Cifs dynamic shares password
Successfully migrated key store
***** WARNING : REBOOTING CM REQUIRES RE-OPENING SECURE STORE MANUALLY. AFTER REBOOT, DISK 
ENCRYPTION AND CIFS PREPOSITION FEATURES ON REMOTE WAE(S) WILL NOT OPERATE 
PROPERLY UNTIL USER RE-OPENS SECURE STORE ON CM BY INPUTTING THE PASSPHRASE *****
successfully initialized and opened secure-store.
Starting cms.

The following example shows how to deactivates secure store encryption:

waas-cm# cms secure-store clear
Secure store clear will result in deletion of CM pki store certificate/private key files
Do you want to continue(yes/no)?yes
Stopping cms.
Successfully migrated user passwords
Successfully migrated Cifs preposition password
Successfully migrated Cifs dynamic shares password
Successfully migrated key store
secure-store clear
Starting cms.

Related CommandsRelated Commands

show cms secure-store

configure

To enter global configuration mode, use the configure EXEC command. You must be in global configuration mode to enter global configuration commands.

configure

To exit global configuration mode, use the end or exit commands. You can also press Ctrl-Z to exit from global configuration mode.

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to enable global configuration mode on a WAAS device:

WAE# configure 
WAE(config)# 

Related Commands

(config) end

(config) exit

show running-config

show startup-config

copy cdrom

To copy software release files from a CD-ROM, use the copy cdrom EXEC command.

copy cdrom install filedir filename

Syntax Description

cdrom

Copies a file from the CD-ROM.

install filedir filename

Installs the software release from the directory location and filename specified.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy a software release file from a CD-ROM:

WAE# copy cdrom install 

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy cdrom wow-recovery

To recover Windows on a virtual blade without reloading the software, use the copy cdrom wow-recovery EXEC command.

copy cdrom wow-recover install filedir filename

Syntax Description

cdrom

Copies the Windows system files from the CD-ROM.

wow-recovery

Recovers the Windows operating system.

install filedir filename

Installs the Windows operating system on the virtual blade from the directory location and Windows filename.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy cdrom wow-recovery EXEC command to recover the Windows system files of a virtual blade. This command allows you to recover Windows on your virtual blade while the WAAS is running, without having to restart your WAE device.

Examples

The following example shows how to recover Windows on a virtual blade:

WAE# copy cdrom wow-recovery install

Related Commands

copy ftp

copy cdrom

virtual-blade

(config) virtual-blade

copy compactflash

To copy software release files from a CompactFlash card, use the copy compactflash EXEC command.

copy compactflash install filename

Syntax Description

compactflash

Copies a file from the CompactFlash card.

install filename

Installs a software release from an image filename.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy a software release file from a CompactFlash card:

WAE# copy compactflash install

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy disk

To copy the configuration or image data from a disk to a remote location using FTP or to the startup configuration, use the copy disk EXEC command.

copy disk {ftp {hostname | ip-address} remotefiledir remotefilename localfilename | startup-config filename}

Syntax Description

disk

Copies a local disk file.

ftp

Copies to a file on an FTP server.

hostname

Hostname of the FTP server.

ip-address

IP address of the FTP server.

remotefiledir

Directory on the FTP server to which the local file is copied.

remotefilename

Name of the local file once it has been copied to the FTP server.

localfilename

Name of the local file to be copied.

startup-config filename

Copies the existing configuration file from the disk to the startup configuration (NVRAM).


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy disk ftp EXEC command to copy files from a SYSFS partition to an FTP server. Use the copy disk startup-config EXEC command to copy a startup-configuration file to NVRAM.

Examples

The following example shows how to copy a startup-configuration file to NVRAM:

WAE# copy disk startup-config

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy ftp

To copy software configuration or image data from an FTP server, use the copy ftp EXEC command.

copy ftp disk {hostname | ip-address} remotefiledir remotefilename localfilename

copy ftp install {hostname | ip-address} remotefiledir remotefilename

copy ftp virtual-blade vb_num disk vb_disk {hostname | ip-address} remotefiledir remotefilename

copy ftp wow-recovery {hostname | ip-address} remotefiledir remotefilename

Syntax Description

disk

Copies a file to a local disk.

hostname

Hostname of the specific server.

ip-address

IP address of the specific server.

remotefiledir

Directory on the FTP server where the image file to be copied is located.

remotefilename

Name of the file to be copied.

localfilename

Name of the copied file as it appears on the local disk.

install

Copies the file from an FTP server and installs the software release file to the local device.

virtual-blade vb_num

Specifies the virtual blade number of the virtual blade disk image to copy to.

disk vb_disk

Specifies the virtual blade disk number of the virtual blade disk image to copy to.

wow-recovery

Recovers the Windows operating system for use on a virtual blade.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy ftp disk EXEC command to copy a file from an FTP server to a SYSFS partition on the WAAS device. To show progress, this command prints a number sign (#) for each 1 MB of data that is copied.

Use the copy ftp install EXEC command to install an image file from an FTP server on a WAAS device. Part of the image goes to a disk and part goes to flash memory.

You can also use the copy ftp install EXEC command to redirect your transfer to a different location. A username and a password have to be authenticated with a primary domain controller (PDC) before the transfer of the software release file to the WAAS device is allowed.

Use the copy ftp wow-recovery EXEC command to copy a Windows operating system image from an FTP server to a virtual blade partition on the WAAS device.

To show progress, this command prints a number sign (#) for each 1 MB of data that is copied.

Upgrading the BIOS

You can remotely upgrade the BIOS on the WAE-511, WAE-512, WAE-611, WAE-612, and the WAE-7326.

All BIOS files needed for a particular hardware model BIOS update are available on Cisco.com as a single .bin package file. This file is a special <WAAS-installable>.bin file that you can install by using the normal software update procedure.

To update the BIOS version on a WAAS device that supports BIOS version updates, you need the following items:

FTP server with the software files

Network connectivity between the device to be updated and the server hosting the update files

Appropriate .bin BIOS update file:

511_bios.bin

611_bios.bin

7326_bios.bin


Caution Be extraordinarily careful when upgrading a Flash BIOS. Make absolutely sure that the BIOS upgrade patch is the exact one required. If you apply the wrong patch, you can render the system unbootable, making it difficult or impossible to recover even by reapplying the proper patch.


Caution Never update a Flash BIOS without first connecting the system to an uninterruptible power supply (UPS). A failed Flash BIOS update can have dire results.

To remotely install a BIOS update file, use the copy ftp install EXEC command as follows:

WAE# copy ftp install ftp-server remote_file_dir 7326_bios.bin

After the BIOS update file is copied to your system, use the reload EXEC command to reboot as follows:

WAE# reload

The new BIOS takes effect after the system reboots.

Examples

The following example shows how to copy an image file from an FTP server and install the file on the local device:

WAE# copy ftp install 10.1.1.1 cisco/waas/4.1 WAAS-4.1.1-k9.bin
Enter username for remote ftp server:biff
Enter password for remote ftp server:*****
Initiating FTP download...
printing one # per 1MB downloaded
Sending:USER biff
10.1.1.1 FTP server (Version) Mon Feb 28 10:30:36 EST
2000) ready.
Password required for biff.
Sending:PASS ***** 
User biff logged in.
Sending:TYPE I
Type set to I.
Sending:PASV
Entering Passive Mode (128,107,193,244,55,156)
Sending:CWD //ftp-sj.cisco.com/cisco/waas/4.0
CWD command successful.
Sending PASV
Entering Passive Mode (128,107,193,244,55,156)
Sending:RETR WAAS-4.1.1-k9.bin
Opening BINARY mode data connection for ruby.bin (87376881 bytes).
###################################################################################
writing flash component:
.................................................................
The new software will run after you reload.

The following example shows how to upgrade the BIOS. All output is written to a separate file (/local1/.bios_upgrade.txt) for traceability. The hardware-dependent files that are downloaded from Cisco.com for the BIOS upgrade are automatically deleted from the WAAS device after the BIOS upgrade procedure has been completed.

WAE-7326# copy ftp install upgradeserver /bios/update53/derived/ 7326_bios.bin
Enter username for remote ftp server:myusername
Enter password for remote ftp server:*****
Initiating FTP download...
printing one # per 1MB downloaded
Sending:USER myusername
upgradeserver.cisco.com FTP server (Version wu-2.6.1-18) ready.
Password required for myusername.
Sending:PASS ********
Please read the file README_dotfiles
 it was last modified on Wed Feb 19 16:10:26 2005- 94 days ago
Please read the file README_first
 it was last modified on Wed Feb 19 16:05:29 2005- 94 days ago
User myusername logged in.
Sending:TYPE I
Type set to I.
Sending:PASV
Entering Passive Mode (128,107,193,240,57,37)
Sending:CWD /bios/update53/derived/
CWD command successful.
Sending PASV
Entering Passive Mode (128,107,193,240,146,117)
Sending:RETR 7326_bios.bin
Opening BINARY mode data connection for 7326_bios.bin (834689 bytes).
Fri Jan  7 15:29:07 UTC 2005
BIOS installer running!
Do not turnoff the system till BIOS installation is complete.
Flash chipset:Macronix 29LV320B
0055000.FLS:280000 [80000]
Erasing block 2f:280000 - 28ffff
Erasing block 30:290000 - 29ffff
Erasing block 31:2a0000 - 2affff
Erasing block 32:2b0000 - 2bffff
Erasing block 33:2c0000 - 2cffff
Erasing block 34:2d0000 - 2dffff
Erasing block 35:2e0000 - 2effff
Erasing block 36:2f0000 - 2fffff
Programming block 2f:280000 - 28ffff
Programming block 30:290000 - 29ffff
Programming block 31:2a0000 - 2affff
Programming block 32:2b0000 - 2bffff
Programming block 33:2c0000 - 2cffff
Programming block 34:2d0000 - 2dffff
Programming block 35:2e0000 - 2effff
Programming block 36:2f0000 - 2fffff
SCSIROM.BIN:260000 [20000]
Erasing block 2d:260000 - 26ffff
Erasing block 2e:270000 - 27ffff
Programming block 2d:260000 - 26ffff
Programming block 2e:270000 - 27ffff
PXEROM.BIN:250000 [10000]
Erasing block 2c:250000 - 25ffff
Programming block 2c:250000 - 25ffff
Primary BIOS flashed successfully
Cleanup BIOS related files that were downloaded....
The new software will run after you reload.
WAE-7326#

The following example shows how to copy a Windows image file from an FTP server and install the file on the virtual blade:

WAE# copy ftp wow-recovery 10.1.1.1 /cisco/waas/4.1 windows.iso
Enter username for remote ftp server:biff
Enter password for remote ftp server:*****
Initiating FTP download...

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy http

To copy configuration or image files from an HTTP server to the WAAS device, use the copy http EXEC command.

copy http install {hostname | ip-address}remotefiledir remotefilename [port portnum] [proxy proxy_portnum] [username username password]

Syntax Description

http

Copies the file from an HTTP server.

install

Copies the file from an HTTP server and installs the software release file to the local device.

hostname

Name of the HTTP server.

ip-address

IP address of the HTTP server.

remotefiledir

Remote file directory.

remotefilename

Remote filename.

port portnum

(Optional) Port number (1-65535) to connect to the HTTP server (the default is 80).

proxy proxy_portnum

(Optional) Allows the request to be redirected to an HTTP proxy server. HTTP proxy server port number (1-65535).

username username password

(Optional) Username and password to access the HTTP proxy server.


Defaults

HTTP server port: 80

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy http install EXEC command to install an image file from an HTTP server and install it on a WAAS device. It transfers the image from an HTTP server to the WAAS device using HTTP as the transport protocol and installs the software on the device. Part of the image goes to a disk and part goes to flash memory. Use the copy http central EXEC command to download a software image into the repository from an HTTP server.

You can also use the copy http install EXEC commands to redirect your transfer to a different location or HTTP proxy server by specifying the proxy hostname | ip-address option. A username and a password have to be authenticated with a primary domain controller (PDC) before the transfer of the software release file to the WAAS device is allowed.

Upgrading the BIOS

You can remotely upgrade the BIOS on the WAE-511, WAE-512, WAE-611, WAE-612, and the WAE-7326. All computer hardware has to work with the software through an interface. The Basic Input Output System (BIOS) provides a computer a built-in starter kit to run the rest of the software from the hard disk drive. The BIOS is responsible for booting the computer by providing a basic set of instructions, performs all the tasks that need to be done at start-up time, such as Power-On Self Test (POST) operations and booting the operating system from the hard disk drive, and provides an interface between the hardware and the operating system in the form of a library of interrupt handlers.

Each time that a key is pressed, the CPU performs an interrupt to read that key, which is similar for other input/output devices, such as serial and parallel ports, video cards, sound cards, hard disk controllers, and so forth. Some older PCs cannot interoperate with all the modern hardware because their BIOS does not support that hardware; the operating system cannot call a BIOS routine to use it. You can solve this problem by replacing the BIOS with a newer one that does support your new hardware or by installing a device driver for the hardware.

All BIOS files needed for a particular hardware model BIOS update are available on Cisco.com as a single .bin package file. This file is a special <WAAS-installable>.bin file that you can install by using the normal software update procedure.

To update the BIOS version on a WAAS device that supports BIOS version updates, you need the following items:

HTTP server with the software files

Network connectivity between the device to be updated and the server hosting the update files

Appropriate .bin BIOS update file:

511_bios.bin

611_bios.bin

7326_bios.bin


Caution Be extraordinarily careful when upgrading a Flash BIOS. Make absolutely sure that the BIOS upgrade patch is the exact one required. If you apply the wrong patch, you can render the system unbootable, making it difficult or impossible to recover even by reapplying the proper patch.


Caution Never update a Flash BIOS without first connecting the system to an uninterruptible power supply (UPS). A failed Flash BIOS update can have dire results.

To install the BIOS update file on a WAAS device, use the copy http install EXEC command as follows:

WAE# copy http install http-server remote_file_dir 7326_bios.bin 
[portnumber]

After the BIOS update file is copied to your system, use the reload EXEC command to reboot the WAAS device as follows:

WAE# reload

The new BIOS takes effect after the system reboots.

Examples

The following example shows how to copy an image file from an HTTP server and install the file on the WAAS device:

WAE# copy http install 10.1.1.1 //ftp-sj.cisco.com/cisco/waas/4.0 WAAS-4.0.0-k9.bin
Enter username for remote ftp server:biff
Enter password for remote ftp server:*****
Initiating FTP download...
printing one # per 1MB downloaded
Sending:USER biff
10.1.1.1 FTP server (Version) Mon Feb 28 10:30:36 EST
2000) ready.
Password required for biff.
Sending:PASS ***** 
User biff logged in.
Sending:TYPE I
Type set to I.
Sending:PASV
Entering Passive Mode (128,107,193,244,55,156)
Sending:CWD //ftp-sj.cisco.com/cisco/waas/4.0
CWD command successful.
Sending PASV
Entering Passive Mode (128,107,193,244,55,156)
Sending:RETR WAAS-4.0.0-k9.bin
Opening BINARY mode data connection for ruby.bin (87376881 bytes).
###################################################################################
writing flash component:
.................................................................
The new software will run after you reload.

The following example shows how to upgrade the BIOS. All output is written to a separate file (/local1/.bios_upgrade.txt) for traceability. The hardware-dependent files that are downloaded from Cisco.com for the BIOS upgrade are automatically deleted from the WAAS device after the BIOS upgrade procedure has been completed.

WAE-7326# copy ftp install upgradeserver /bios/update53/derived/ 7326_bios.bin
Enter username for remote ftp server:myusername
Enter password for remote ftp server:*****
Initiating FTP download...
printing one # per 1MB downloaded
Sending:USER myusername
upgradeserver.cisco.com FTP server (Version wu-2.6.1-18) ready.
Password required for myusername.
Sending:PASS ********
Please read the file README_dotfiles
 it was last modified on Wed Feb 19 16:10:26 2005- 94 days ago
Please read the file README_first
 it was last modified on Wed Feb 19 16:05:29 2005- 94 days ago
User myusername logged in.
Sending:TYPE I
Type set to I.
Sending:PASV
Entering Passive Mode (128,107,193,240,57,37)
Sending:CWD /bios/update53/derived/
CWD command successful.
Sending PASV
Entering Passive Mode (128,107,193,240,146,117)
Sending:RETR 7326_bios.bin
Opening BINARY mode data connection for 7326_bios.bin (834689 bytes).
Fri Jan  7 15:29:07 UTC 2005
BIOS installer running!
Do not turnoff the system till BIOS installation is complete.
Flash chipset:Macronix 29LV320B
0055000.FLS:280000 [80000]
Erasing block 2f:280000 - 28ffff
Erasing block 30:290000 - 29ffff
Erasing block 31:2a0000 - 2affff
Erasing block 32:2b0000 - 2bffff
Erasing block 33:2c0000 - 2cffff
Erasing block 34:2d0000 - 2dffff
Erasing block 35:2e0000 - 2effff
Erasing block 36:2f0000 - 2fffff
Programming block 2f:280000 - 28ffff
Programming block 30:290000 - 29ffff
Programming block 31:2a0000 - 2affff
Programming block 32:2b0000 - 2bffff
Programming block 33:2c0000 - 2cffff
Programming block 34:2d0000 - 2dffff
Programming block 35:2e0000 - 2effff
Programming block 36:2f0000 - 2fffff
SCSIROM.BIN:260000 [20000]
Erasing block 2d:260000 - 26ffff
Erasing block 2e:270000 - 27ffff
Programming block 2d:260000 - 26ffff
Programming block 2e:270000 - 27ffff
PXEROM.BIN:250000 [10000]
Erasing block 2c:250000 - 25ffff
Programming block 2c:250000 - 25ffff
Primary BIOS flashed successfully
Cleanup BIOS related files that were downloaded....
The new software will run after you reload.

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy running-config

To copy a configuration or image data from the current configuration, use the copy running-config EXEC command.

copy running-config {disk filename | startup-config | tftp {hostname | ip-address} remotefilename}

Syntax Description

running-config

Copies the current system configuration.

disk filename

Copies the current system configuration to a disk file. Specify the name of the file to be created on a disk.

startup-config

Copies the running configuration to startup configuration (NVRAM).

tftp

Copies the running configuration to a file on a TFTP server.

hostname

Hostname of the TFTP server.

ip-address

IP address of the TFTP server.

remotefilename

Remote filename of the configuration file to be created on the TFTP server. Use the complete pathname.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy running-config EXEC command to copy the running system configuration of the WAAS device to a SYSFS partition, flash memory, or TFTP server. The copy running-config startup-config EXEC command is equivalent to the write memory EXEC command.

Examples

The following example shows how to copy the current system configuration to startup configuration (NVRAM):

WAE# copy running-config startup-config

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy startup-config

To copy configuration or image data from the startup configuration, use the copy startup-config EXEC command.

copy startup-config {disk filename | running-config | tftp {hostname | ip-address} remotefilename}

Syntax Description

startup-config

Copies the startup configuration.

disk filename

Copies the startup configuration to a disk file. Specify the name of the startup configuration file to be copied to the local disk.

running-config

Copies the startup configuration to running configuration.

tftp

Copies the startup configuration to a file on a TFTP server.

hostname

Hostname of the TFTP server.

ip-address

IP address of the TFTP server.

remotefilename

Remote filename of the startup configuration file to be created on the TFTP server. Use the complete pathname.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy startup-config EXEC command to copy the startup configuration file to a TFTP server or to a SYSFS partition.

Examples

The following example shows how to copy the startup configuration file to the running configuration:

WAE# copy startup-config running-config

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy sysreport

To copy system troubleshooting information from the device, use the copy sysreport EXEC command.

copy sysreport disk filename

copy sysreport ftp {hostname | ip-address} remotedirectory remotefilename

copy sysreport tftp {hostname | ip-address} remotefilename} [start-date {day month | month day} year [end-date {day month | month day} year]]

Syntax Description

sysreport

Generates and saves a report containing WAAS system information in a file.

disk filename

Copies system information to a disk file. Specify the name of the file to be created on a disk. Note that .tar.gz is appended to the filename that you specify.

ftp

Copies system information to a FTP server.

hostname

Hostname of the server.

ip-address

IP address of the server.

remotedirectory

Remote directory where the system information file is to be created on the FTP server.

remotefilename

Remote filename of the system information file to be created on the FTP server.

tftp

Copies system information to a TFTP server.

remotefilename

Remote filename of the system information file to be created on the TFTP server. Use the complete pathname.

start-date

(Optional) Start date of the information in the generated system report.

day month

Start date day of the month (1-31) and month of the year (January, February, March, April, May, June, July, August, September, October, November, December). You can alternately specify the month first, followed by the day.

year

Start date year (1993-2035).

end-date

(Optional) End date of information in the generated system report. If omitted, this date defaults to today. The report includes files through the end of this day.

day month

End date day of the month (1-31) and month of the year (January, February, March, April, May, June, July, August, September, October, November, December). You can alternately specify the month first, followed by the day.

year

End date year (1993-2035).


Defaults

If end-date is not specified, today is used.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The copy sysreport command consumes significant CPU and disk resources and can adversely affect system performance while it is running.

Examples

The following example shows how to copy system information to the file mysysinfo on the local WAAS device:

WAE# copy sysreport disk mysysinfo start-date 1 April 2006 end-date April 30 2006

The following example shows how to copy system information by FTP to the file foo in the root directory of the FTP server named myserver:

WAE# copy sysreport ftp myserver / foo start-date 1 April 2006 end-date April 30 2006

Related Commands

show running-config

show startup-config

wafs

copy system-status

To copy status information from the system for debugging, use the copy system-status EXEC command.

copy system-status disk filename

Syntax Description

system-status

Copies the system status to a disk file.

disk filename

Name of the file to be created on the disk.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy system-status EXEC command to create a file on a SYSFS partition that contains hardware and software status information.

Examples

The following example shows how to copy the system status to a disk file:

WAE# copy system-status disk file1

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy tech-support

To copy the configuration or image data from the system to use when working with Cisco TAC, use the copy tech-support EXEC command.

copy tech-support {disk filename | ftp {hostname | ip-address} remotedirectory remotefilename | tftp {hostname | ip-address} remotefilename}

Syntax Description

tech-support

Copies system information for technical support.

disk filename

Copies system information for technical support to a disk file. Specify the name of the file to be created on disk.

ftp

Copies system information for technical support to an FTP server.

hostname

Hostname of the FTP server.

ip-address

IP address of the FTP server.

remotedirectory

Remote directory of the system information file to be created on the FTP server. Use the complete pathname.

remotefilename

Remote filename of the system information file to be created on the FTP server.

tftp

Copies system information for technical support to a TFTP server.

hostname

Hostname of the TFTP server.

ip-address

IP address of the TFTP server.

remotefilename

Remote filename of the system information file to be created on the TFTP server. Use the complete pathname.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy tech-support tftp EXEC command to copy technical support information to a TFTP server or to a SYSFS partition.

Examples

The following example shows how to copy system information for tech support to a disk file:

WAE# copy tech-support disk file1

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy tftp

To copy configuration or image data from a TFTP server, use the copy tftp EXEC command.

copy tftp disk {hostname | ip-address} remotefilename localfilename

copy tftp running-config {hostname | ip-address} remotefilename

copy tftp startup-config {hostname | ip-address} remotefilename

Syntax Description

tftp

Copies an image from a TFTP server.

disk

Copies an image from a TFTP server to a disk file.

hostname

Hostname of the TFTP server.

ip-address

IP address of the TFTP server.

remotefilename

Name of the remote image file to be copied from the TFTP server. Use the complete pathname.

localfilename

Name of the image file to be created on the local disk.

running-config

Copies an image from a TFTP server to the running configuration.

startup-config

Copies an image from a TFTP server to the startup configuration.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy configuration or image data from a TFTP server to the running configuration:

WAE# copy tftp running-config

Related Commands

install

reload

show running-config

show startup-config

wafs

write

copy virtual-blade

To copy software configuration or image data from a virtual blade disk image to an FTP server, use the copy virtual-blade EXEC command.

copy virtual-blade vb_num disk vb_disk ftp {hostname | ip-address} remotefiledir remotefilename

Syntax Description

virtual-blade vb_num

Specifies the virtual blade number of the virtual blade disk image to copy to.

disk vb_disk

Specifies the virtual blade disk number of the virtual blade disk image to copy to.

ftp

Writes to an FTP server.

hostname

Hostname of the specific server.

ip-address

IP address of the specific server.

remotefiledir

Directory where the image file to be copied is located.

remotefilename

Name of the file to be copied.


Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy an image file from a virtual blade to an FTP server:

WAE# copy virtual-blade 1 disk 1 ftp 10.75.16.234 / file.img

Related Commands

copy ftp

install

reload

show running-config

show startup-config

wafs

write

cpfile

To make a copy of a file, use the cpfile EXEC command.

cpfile oldfilename newfilename

Syntax Description

oldfilename

Name of the file to copy.

newfilename

Name of the copy to be created.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Only SYSFS files can be copied.

Examples

The following example shows how to create a copy of a file:

WAE# cpfile fe512-194616.bin fd512-194618.bin

Related Commands

deltree

dir

lls

ls

mkdir

pwd

rename

crypto delete

To remove SSL certificate and key files, use the crypto delete EXEC command.

crypto delete {ca-certificate filename | pkcs12 filename}

Use the crypto delete EXEC command to remove a certificate from your WAE's secure store. If you only want to disassociate a certificate from an accelerated service, use no server-cert-key in crypto ssl services accelerated-service mode.

Syntax Description

ca-certificate filename

Deletes a certificate authority certificate file.

pkcs12 filename

Deletes a PKCS12 format file. (PKCS12 files contain both the private encryption key and the public key certificate.)


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to delete the CA certificate file mycert.ca:

WAE# crypto delete ca-certificate mycert.ca

Related Commands

crypto export

crypto generate

crypto import

crypto export

To export SSL certificate and key files, use the crypto export EXEC command.

crypto export {ca-certificate filename | pkcs12 {factory-self-signed | filename} {pem-cert-key | pem-cert-only | pem-key-only | pkcs12}}{disk pathname | ftp address | sftp address | terminal | tftp address}

Syntax Description

ca-certificate filename

Export a certificate authority certificate file.

pkcs12

Export a PKCS12 format file. (PKCS12 files contain both the private encryption key and the public key certificate.)

factory-self-signed

Specifies that the SSL PKCS file is to be self-signed.

filename

The name of the PKCS12 file to be exported.

pem-cert-key

Export both the certificate and key in PEM format.

pem-cert-only

Export only the certificate in PEM format.

pem-key-only

Export only the key in PEM format.

pkcs12

Export both the certificate and key in PKCS12 format.

disk pathname

Export to a disk. Type the disk filename including the full path.

ftp address

Export to FTP. Type the FTP server's IP address or hostname.

sftp address

Export to secure FTP. Type the secure FTP server's IP address or hostname.

terminal

Export to a terminal.(Not available for crypto export pkcs12.)

tftp address

Export to TFTP. Type the TFTP server's IP address or hostname.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to export a CA certificate file named mycert.ca to an FTP server:

WAE# crypto export ca-certificate mycert.ca ftp 1.2.3.4 dir1 mycert.ca

The following example shows how to export the certificate and private key from a PKCS12 file named myfile.p12 to a PEM file on the local1 directory on the hard drive:

WAE# crypto export pkcs12 myfile.p12 pkcs12 disk /local1/myfile.p12

Related Commands

crypto delete

crypto generate

crypto import

crypto generate

To generate a self-signed certificate or a certificate signing request, use the crypt generate EXEC command.

crypto generate {csr rsa modulus {1024 | 1536 | 2048 | 512 | 768}{disk pathname | ftp address | sftp address | terminal | tftp address} | self-signed-cert filename [exportable] rsa modulus {1024 | 1536 | 2048 | 512 | 768}}

Syntax Description

csr

Generate a certificate signing request (CSR).

rsa modulus

Specify the size of the RSA modulus to be used for the CSR.

1024 | 1536 | 2048 | 512 | 768

The size (number of bits) used for the RSA modulus.

disk pathname

Generate the file to a disk. Type the disk filename including the full path.

ftp address

Generate the file to FTP. Type the FTP server's IP address or hostname.

sftp address

Generate the file to secure FTP. Type the secure FTP server's IP address or hostname.

terminal

Generate the file to a terminal.

tftp address

Generate the file to TFTP. Type the TFTP server's IP address or hostname.

self-signed-cert filename

Generate a self-signed SSL encryption certificate. The filename of the self-signed certificate to be generated must have the .p12 file extension.

exportable

Allows the self-signed certificate to be exported.

rsa modulus

Specify the size of the RSA modulus to be used when generating the self-signed certificate.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to create an exportable self-signed certificate. The certificate file is named myfile.p12 and is created using a 512-bit RSA modulus.

WAE# crypto generate self-signed-cert myfile.p12 exportable rsa modulus 512
Generating a 512 bit RSA private key
..........++++++++++++
...++++++++++++
-----
You are about to be asked to enter information that will be incorporated
into your certificate request.
What you are about to enter is what is called a Distinguished Name or a DN.
There are quite a few fields but you can leave some blank
For some fields there will be a default value,
If you enter '.', the field will be left blank.
-----
Country Name (2 letter code) [US]:US
State or Province Name (full name) [California]:<cr> (Press Enter to accept the default.)
Locality Name (eg, city) [San Jose]:San Jose
Organization Name (eg, company) [Cisco Systems]:
Organizational Unit Name (eg, section) [ADBU]:
Common Name (eg, YOUR name) [www.cisco.com]:
Email Address [tac@cisco.com]:

WAE#

Related Commands

crypto delete

crypto export

crypto import

crypto import

To import SSL certificates and key files, use the crypto import EXEC command.

crypto import {ca-certificate filename | pkcs12 filename [exportable]}{pem-cert-key | pkcs12}}{disk pathname | ftp address | sftp address | terminal | tftp address}

Syntax Description

ca-certificate filename

Import a certificate authority certificate file. The name of the CA certificate file to be imported (PEM format) must have .ca extension.

pkcs12 filename

Specifies a certificate intended for the management or an accelerated service (PKCS12 format). A PKCS12 file contains both the private encryption key and the public key certificate. The name of the PKCS12 file to be imported must have a .p12 extension.

Note: DSA-encoded certificates are not supported and will not be imported.

exportable

Configures the imported certificate to be exportable.

pem-cert-key

Import both the certificate and key in PEM format.

When you use pem-cert-key, you must specify the pathname and filename or the address and filename for both the certificate file and the key file for disk, ftp, sftp, and tftp.

pkcs12

Import both the certificate and key in PKCS12 format.

disk pathname

Import from a disk. Type the disk filename including the full path.

ftp address

Import from FTP. Type the FTP server's IP address or hostname.

sftp address

Import from secure FTP. Type the secure FTP server's IP address or hostname.

terminal

Import from a terminal.

tftp address

Import from TFTP. Type the TFTP server's IP address or hostname.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator


Note DSA certificates and keys cannot be imported.


Examples

The following example shows how to import a CA certificate file named mycert.ca from a TFTP server:

WAE# crypto import ca-certificate mycert.ca tftp 00.00.00.00

Related Commands

crypto delete

crypto export

crypto generate

crypto pki

To initialize the PKI managed store, use the crypto pki EXEC command.

crypto pki managed-store initialize

Syntax Description

managed-store

Specifies managed store commands.

initialize

Initializes the PKI managed store.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to initialize the PKI managed store:

WAE# crypto pki managed-store initialize

Related Commands

crypto export

crypto generate

crypto import

debug aaa accounting

To monitor and record AAA accounting debugging, use the debug aaa accounting EXEC command. To disable debugging, use the undebug form of this command.

debug aaa accounting

undebug aaa accounting

Syntax Description

aaa accounting

(Optional) Enables AAA accounting actions.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable AAA accounting debug monitoring:

WAE# debug aaa accounting

Related Commands

show debugging

debug accelerator

To monitor and record accelerator debugging, use the debug accelerator EXEC command. To disable debugging, use the undebug form of this command.

debug accelerator cifs [shell | all]

undebug accelerator cifs [shell | all]

debug accelerator generic [connection | misc | shell | stats | all]

undebug accelerator generic [connection | misc | shell | stats | all]

debug accelerator http [cli | connection | shell | all]

undebug accelerator http [cli | connection | shell | all]

debug accelerator mapi [all | Common-flow | DCERPC-layer | EMSMDB-layer | IO | ROP-layer | ROP-parser | RCP-parser | shell | Transport | Utilities]

undebug accelerator mapi [all | Common-flow | DCERPC-layer | EMSMDB-layer | IO | ROP-layer | ROP-parser | RCP-parser | shell | Transport | Utilities]

debug accelerator nfs [async-write | attributes-cache | nfs-v3 | read-ahead | rpc | shell | utils | all]

undebug accelerator nfs [async-write | attributes-cache | nfs-v3 | read-ahead | rpc | shell | utils | all]

debug accelerator video [all | gateway | shell | windows-media
[client-ip ip-addr | server-ip ip-addr]]

undebug accelerator video [all | gateway | shell | windows-media
[client-ip ip-addr | server-ip ip-addr]]

Syntax Description

accelerator

Enables accelerator debugging.

cifs

(Optional) Enables CIFS accelerator debugging.

shell

Enables accelerator shell debugging.

all

Enables all accelerator debugging of a specified type.

generic

Enables generic accelerator debugging.

connection

Enables accelerator connection debugging.

misc

Enables generic accelerator miscellaneous debugging.

stats

Enables generic accelerator statistics debugging.

http

Enables HTTP accelerator debugging.

cli

Enables configuration CLI debugging.

mapi

Enables MAPI accelerator debugging.

Common-flow

Enables MAPI common flow debugging.

DCERPC-layer

Enables MAPI DCERPC layer flow debugging.

EMSMDB-layer

Enables MAPI EMSMDB layer flow debugging.

IO

Enables MAPI IO flow debugging.

ROP-layer

Enables MAPI ROP layer flow debugging.

ROP-parser

Enables MAPI ROP parser flow debugging.

RCP-parser

Enables MAPI RCP parser flow debugging.

shell

Enables MAPI shell flow debugging.

Transport

Enables MAPI transport flow debugging.

Utilities

Enables MAPI utilities flow debugging.

nfs

Enables NFS accelerator debugging.

async-write

Enables NFS asynchronous write optimization debugging.

attributes-cache

Enables NFS attributes cache debugging.

nfs-v3

Enables NFS version 3 layer debugging.

read-ahead

Enables NFS read ahead optimization debugging.

rpc

Enables NFS RPC layer debugging.

shell

Enables NFS shell debugging.

utils

Enables NFS utilities debugging.

video

Enables video accelerator debugging.

gateway

Enables debugging of the media independent gateway module of the video accelerator.

windows-media

Enables debugging of the Windows Media module of the video accelerator.

client-ip ip-addr

Specifies the client IP address.

server-ip ip-addr

Specifies the server IP address.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The output associated with the debug accelerator name module command for an application accelerator is written to the file nameao-errorlog.current, where name is the accelerator name. The accelerator information manager debug output is written to the file aoim-errorlog.current.

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all accelerator debug monitoring:

WAE# debug accelerator all

Related Commands

show debugging

debug all

To monitor and record all debugging, use the debug all EXEC command. To disable debugging, use the undebug form of this command.

debug all

undebug all

Syntax Description

all

Enables all debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all debug monitoring:

WAE# debug all

Related Commands

show debugging

debug authentication

To monitor and record authentication debugging, use the debug authentication EXEC command. To disable debugging, use the undebug form of this command.

debug authentication {content-request | user | windows-domain}

undebug authentication {content-request | user | windows-domain}

Syntax Description

authentication

(Optional) Enables authentication debugging.

content-request

Enables content request authentication debugging.

user

Enables debugging of the user login against the system authentication.

windows-domain

Enables Windows domain authentication debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable user authentication debug monitoring, verify that it is enabled, and then disable debug monitoring:

WAE# debug authentication user
WAE# show debugging
Debug authentication (user) is ON
WAE# no debug authentication user

Related Commands

show debugging

debug buf

To monitor and record buffer manager debugging, use the debug buf EXEC command. To disable debugging, use the undebug form of this command.

debug buf {all | dmbuf | dmsg}

undebug buf {all | dmbuf | dmsg}

Syntax Description

buf

(Optional) Enables buffer manager debugging.

all

Enables all buffer manager debugging.

dmbuf

Enables only dmbuf debugging.

dmsg

Enables only dmsg debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all buffer manager debug monitoring:

WAE# debug buff all

Related Commands

show debugging

debug cdp

To monitor and record CDP debugging, use the debug cdp EXEC command. To disable debugging, use the undebug form of this command.

debug cdp {adjacency | events | ip | packets}

undebug cdp {adjacency | events | ip | packets}

Syntax Description

cdp

(Optional) Enables CDP debugging.

adjacency

Enables CDP neighbor information debugging.

events

Enables CDP events debugging.

ip

Enables CDP IP debugging.

packets

Enables packet-related CDP debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable CDP events debug monitoring:

WAE# debug cdp events

Related Commands

show debugging

debug cli

To monitor and record CLI debugging, use the debug cli EXEC command. To disable debugging, use the undebug form of this command.

debug cli {all | bin | parser}

undebug cli {all | bin | parser}

Syntax Description

cli

(Optional) Enables CLI debugging.

all

Enables all CLI debugging.

bin

Enables CLI command binary program debugging.

parser

Enables CLI command parser debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all CLI debug monitoring:

WAE# debug cli all

Related Commands

show debugging

debug cms

To monitor and record CMS debugging, use the debug cms EXEC command. To disable debugging, use the undebug form of this command.

debug cms

undebug cms

Syntax Description

cms

(Optional) Enables CMS debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable CMS debug monitoring:

WAE# debug cms

Related Commands

show debugging

debug dataserver

To monitor and record data server debugging, use the debug dataserver EXEC command. To disable debugging, use the undebug form of this command.

debug dataserver {all | clientlib | server}

undebug dataserver {all | clientlib | server}

Syntax Description

dataserver

(Optional) Enables data server debugging.

all

Enables all data server debugging.

clientlib

Enables data server client library module debugging.

server

Enables data server module debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all data server debug monitoring:

WAE# debug dataserver all

Related Commands

show debugging

debug dhcp

To monitor and record DHCP debugging, use the debug dhcp EXEC command. To disable debugging, use the undebug form of this command.

debug dhcp

undebug dhcp

Syntax Description

dhcp

(Optional) Enables DHCP debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable DHCP debug monitoring:

WAE# debug dhcp

Related Commands

show debugging

debug dre

To monitor and record DRE debugging, use the debug dre EXEC command. To disable debugging, use the undebug form of this command.

debug dre {aggregation | all | cache | connection {aggregation [acl] | cache [acl] | core [acl] | message [acl] | misc [acl] | acl} | core | lz | message | misc}

undebug dre {aggregation | all | cache | connection {aggregation [acl] | cache [acl] | core [acl] | message [acl] | misc [acl] | acl} | core | lz | message | misc}

Syntax Description

dre

(Optional) Enables DRE debugging.

aggregation

Enables DRE chunk-aggregation debugging.

all

Enables the debugging of all DRE commands.

cache

Enables DRE cache debugging.

connection

Enables DRE connection debugging.

acl

ACL to limit connections traced.

message

Enables DRE message debugging for a specified connection.

misc

Enables DRE other debugging for a specified connection.

core

Enables DRE core debugging.

lz

Enables DRE lz debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all DRE debug monitoring:

WAE# debug dre all

Related Commands

show debugging

debug egress-method

To monitor and record egress method debugging, use the debug egress-method EXEC command. To disable debugging, use the undebug form of this command.

debug egress-method connection

undebug egress-method connection

Syntax Description

eggress-method connection

(Optional) Enables egress method connection debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all egress method debug monitoring:

WAE# debug egress-method connection

Related Commands

show debugging

debug emdb

To monitor and record embedded database debugging, use the debug emdb EXEC command. To disable debugging, use the undebug form of this command.

debug emdb [level [levelnum]]

undebug emdb [level [levelnum]]

Syntax Description

emdb

(Optional) Enables embedded database debugging.

level

(Optional) Enables the specified debug level for EMDB service.

levelnum

(Optional) Debug level to disable. Level 0 disables debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all embedded database debug monitoring:

WAE# debug emdb all

Related Commands

show debugging

debug epm

To monitor and record DCE-RPC EPM debugging, use the debug epm EXEC command. To disable debugging, use the undebug form of this command.

debug epm

undebug epm

Syntax Description

epm

(Optional) Enables DCE-RPC EPM debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable EPM debug monitoring:

WAE# debug epm

Related Commands

show debugging

debug flow

To monitor and record network traffic flow debugging, use the debug flow EXEC command. To disable debugging, use the undebug form of this command.

debug flow monitor tcpstat-v1

undebug flow monitor tcpstat-v1

Syntax Description

flow

(Optional) Enables network traffic flow debugging.

monitor

Enables monitor flow performance debugging commands.

tcpstat-v1

Enables tcpstat-v1 debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable network traffic flow debug monitoring:

WAE# debug flow monitor tcpstat-v1

Related Commands

show debugging

debug generic-gre

To monitor and record generic GRE egress method debugging, use the debug generic-gre EXEC command. To disable debugging, use the undebug form of this command.

debug generic-gre

undebug generic-gre

Syntax Description

generic-gre

(Optional) Enables generic GRE egress method debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable generic GRE egress method debug monitoring:

WAE# debug generic-gre

Related Commands

show debugging

debug key-manager

To monitor and record Central Manager key manager debugging, use the debug key-manager EXEC command. To disable debugging, use the undebug form of this command.

debug key-manager

undebug key-manager

Syntax Description

key-manager

(Optional) Enables the Central Manager key manager debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable Central Manager key manager debug monitoring:

WAE# debug key-manager

Related Commands

show debugging

debug logging

To monitor and record logging debugging, use the debug logging EXEC command. To disable debugging, use the undebug form of this command.

debug logging all

undebug logging all

Syntax Description

logging

(Optional) Enables logging debugging.

all

Enables all logging debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all logging debug monitoring:

WAE# debug logging all

Related Commands

show debugging

debug ntp

To monitor and record NTP debugging, use the debug ntp EXEC command. To disable debugging, use the undebug form of this command.(

debug ntp

undebug ntp

Syntax Description

ntp

(Optional) Enables NTP debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable NTP debug monitoring:

WAE# debug ntp

Related Commands

show debugging

debug print-spooler

To monitor and record print spooler debugging, use the debug print-spooler EXEC command. To disable debugging, use the undebug form of this command.

debug print-spooler {all | brief | errors | warnings}

undebug print-spooler {all | brief | errors | warnings}

Syntax Description

print-spooler

(Optional) Enables print spooler debugging.

all

Enables print spooler debugging using all debug features.

brief

Enables print spooler debugging using only brief debug messages.

errors

Enables print spooler debugging using only the error conditions.

warnings

Enables print spooler debugging using only the warning conditions.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all print spooler debug monitoring:

WAE# debug print-spooler all

Related Commands

show debugging

debug rbcp

To monitor and record RBCP debugging, use the debug rbcp EXEC command. To disable debugging, use the undebug form of this command.

debug rbcp

undebug rbcp

Syntax Description

rbcp

(Optional) Enables RBCP debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable RBCP debug monitoring:

WAE# debug rbcp

Related Commands

show debugging

debug rpc

To monitor and record remote procedure calls (RPC) debugging, use the debug rpc EXEC command. To disable debugging, use the undebug form of this command.

debug rpc

undebug rpc {detail | trace}

Syntax Description

rpc

(Optional) Enables the remote procedure calls (RPC) debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable RPC detail debug monitoring:

WAE# debug rpd detail

Related Commands

show debugging

debug snmp

To monitor and record SNMP debugging , use the debug snmp EXEC command. To disable debugging, use the undebug form of this command.

debug snmp {all | cli | main | mib | traps}

undebug snmp {all | cli | main | mib | traps}

Syntax Description

snmp

(Optional) Enables SNMP debugging.

all

Enables all SNMP debug commands.

cli

Enables SNMP CLI debugging.

main

Enables SNMP main debugging.

mib

Enables SNMP MIB debugging.

traps

Enables SNMP trap debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all SNMP debug monitoring:

WAE# debug snmp all

Related Commands

show debugging

debug stats

To monitor and record statistics debugging, use the debug stats EXEC command. To disable debugging, use the undebug form of this command.

debug stats {all | collections | computation | history}

undebug stats {all | collections | computation | history}

Syntax Description

stats

(Optional) Enables statistics debugging.

all

Enables all statistics debug commands.

collection

Enables collection statistics debugging.

computation

Enables computation statistics debugging.

history

Enables history statistics debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all statistics debug monitoring:

WAE# debug stat all

Related Commands

show debugging

debug tfo

To monitor and record TFO flow optimization debugging, use the debug tfo EXEC command. To disable debugging, use the undebug form of this command.

debug tfo {buffer-mgr | connection [auto-discovery | comp-mgr [acl] | conn-mgr [acl] | egress-method [acl] | filtering [acl] | netio-engine [acl] | policy-engine [acl] |
synq [acl] | acl] | stat-mgr | translog}

undebug tfo {buffer-mgr | connection [auto-discovery [acl] | comp-mgr [acl] | conn-mgr [acl] | egress-method [acl] | filtering [acl] | netio-engine [acl] | policy-engine [acl] | synq [acl] | acl] | stat-mgr | translog}

Syntax Description

buffer-mgr

Enables TFO flow optimization debugging.

connection

Enables TFO connection debugging.

auto-discovery

(Optional) Enables TFO connection debugging for the auto-discovery module.

acl

(Optional) ACL to limit TFO connections.

comp-mgr

Enables TFO connection debugging for the compression module.

conn-mgr

Enables TFO connection debugging for the connection manager.

egress-method

Enables TFO connection debugging for the connection egress method.

filtering

Enables TFO connection debugging for the filtering module.

netio-engine

Enables TFO connection debugging for the network input/output module.

policy-engine

Enables TFO connection debugging of application policies.

synq

Enables TFO connection debugging for the SynQ module.

stat-mgr

Enables TFO statistics manager debugging.

translog

Enables TFO transaction log debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all TFO flow optimization debug monitoring:

WAE# debug tfo all

Related Commands

show debugging

debug translog

To monitor and record transaction logging debugging, use the debug translog EXEC command. To disable debugging, use the undebug form of this command.

debug translog {detail | export | info}

undebug translog export

Syntax Description

translog

(Optional) Enables transaction logging debugging.

detail

Enables transaction log detailed debugging.

export

Enables transaction log FTP export debugging.

info

Enables transaction log high level debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable transaction logging detail debug monitoring:

WAE# debug translog detail

Related Commands

show debugging

debug wafs

To set the log level of WAFS running components, use the debug wafs EXEC command. To disable debugging, use the undebug form of this command.

debug wafs {{all | core-fe | edge-fe | manager | utilities} {debug | error | info | warn}}

undebug wafs {{all | core-fe | edge-fe | manager | utilities} {debug | error | info | warn}}

Syntax Description

wafs

(Optional) Unsets the notification level (debug, info, warn, error) at which messages from the WAAS software component and utilities are logged.

all

Unsets the logging level for all software components and utilities at once.

core-fe

Unsets the logging level for WAEs s acting as a core File Engine.

edge-fe

Unsets the logging level for WAEs acting as an edge File Engine.

manager

Unsets the logging level for the Device Manager.

utilities

Unsets the logging level for WAAS utilities.

debug

Specifies debug.

error

Specifies error.

info

Specifies info.

warn

Specifies warn.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to set the log level for all WAFS components to error level:

WAE# debug wafs all error

Related Commands

show debugging

debug wccp

To monitor and record WCCP information debugging, use the debug wccp EXEC command. To disable debugging, use the undebug form of this command.

debug wccp {all | detail | error | events | keepalive | packets | slowstart}

undebug wccp {all | detail | error | events | keepalive | packets | slowstart}

Syntax Description

wccp

(Optional) Enables the WCCP information debugging.

all

Enables all WCCP debugging functions.

detail

Enables the WCCP detail debugging.

error

Enables the WCCP error debugging.

events

Enables the WCCP events debugging.

keepalive

Enables the debugging for WCCP keepalives that are sent to the applications.

packets

Enables the WCCP packet-related information debugging.

slowstart

Enables the WCCP slow-start debugging.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the "Obtaining Documentation and Submitting a Service Request" section on page xix.

If the watchdog utility is not running, the message "WAAS is not running" appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/module_name-errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name-errorlog.#, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical global configuration command.

For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.

For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.

For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable WCCP information debug monitoring:

WAE# debug wccp all

Related Commands

show debugging

delfile

To delete a file from the current directory, use the delfile EXEC command.

delfile filename

Syntax Description

filename

Name of the file to delete.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the delfile EXEC command to remove a file from a SYSFS partition on the disk drive of the WAAS device.

Examples

The following example shows how to delete a temporary file from the /local1 directory using an absolute path:

WAE# delfile /local1/tempfile

Related Commands

cpfile

dir

lls

ls

mkdir

pwd

rename

deltree

To remove a directory with all of its subdirectories and files, use the deltree EXEC command.

deltree directory

Syntax Description

directory

Name of the directory tree to delete.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the deltree EXEC command to remove a directory and all files within the directory from the WAAS SYSFS file system. No warning is given that you are removing the subdirectories and files.


Note Make sure that you do not remove files or directories required for the WAAS device to function properly.


Examples

The following example shows how to delete the testdir directory from the /local1 directory:

WAE# deltree /local1/testdir

Related Commands

cpfile

dir

lls

ls

mkdir

pwd

rename

dir

To view details of one file or all files in a directory, use the dir EXEC command.

dir [directory]

Syntax Description

directory

(Optional) Name of the directory to list.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the dir EXEC command to view a detailed list of files contained within the working directory, including information about the file name, size, and time created. The lls EXEC command produces the same output.

Examples

The following example shows how to create a detailed list of all the files for the current directory:

WAE# dir   
size          time of last change             name
-------------  -------------------------          -----------
         4096  Fri Feb 24 14:40:00 2006  <DIR>    actona
         4096  Tue Mar 28 14:42:44 2006  <DIR>    core_dir
         4096  Wed Apr 12 20:23:10 2006  <DIR>    crash
         4506  Tue Apr 11 13:52:45 2006           dbupgrade.log
         4096  Tue Apr  4 22:50:11 2006  <DIR>    downgrade
         4096  Sun Apr 16 09:01:56 2006  <DIR>    errorlog
         4096  Wed Apr 12 20:23:41 2006  <DIR>    logs
        16384  Thu Feb 16 12:25:29 2006  <DIR>    lost+found
         4096  Wed Apr 12 03:26:02 2006  <DIR>    sa
        24576  Sun Apr 16 23:38:21 2006  <DIR>    service_logs
         4096  Thu Feb 16 12:26:09 2006  <DIR>    spool
      9945390  Sun Apr 16 23:38:20 2006           syslog.txt
     10026298  Thu Apr  6 12:25:00 2006           syslog.txt.1
     10013564  Thu Apr  6 12:25:00 2006           syslog.txt.2
     10055850  Thu Apr  6 12:25:00 2006           syslog.txt.3
     10049181  Thu Apr  6 12:25:00 2006           syslog.txt.4
         4096  Thu Feb 16 12:29:30 2006  <DIR>    var
          508  Sat Feb 25 13:18:35 2006           wdd.sh.signed

The following example shows how to display the detailed information for only the logs directory:

WAE# dir logs
size          time of last change             name
-------------  -------------------------          -----------
         4096  Thu Apr  6 12:13:50 2006  <DIR>    actona
         4096  Mon Mar  6 14:14:41 2006  <DIR>    apache
         4096  Sun Apr 16 23:36:40 2006  <DIR>    emdb
         4096  Thu Feb 16 11:51:51 2006  <DIR>    export
           92  Wed Apr 12 20:23:20 2006           ftp_export.status
         4096  Wed Apr 12 20:23:43 2006  <DIR>    rpc_httpd
            0  Wed Apr 12 20:23:41 2006           snmpd.log
         4096  Sun Mar 19 18:47:29 2006  <DIR>    tfo

Related Commands

lls

ls

disable

To turn off privileged EXEC commands, use the disable EXEC command.

disable

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels, user and privileged. To access privileged-level EXEC mode, enter the enable EXEC command at the user access level prompt and specify a privileged EXEC password (superuser or admin-equivalent password) when prompted for a password.

WAE> enable
Password: 

The disable command places you in the user-level EXEC shell (notice the prompt change).

Examples

The following example shows how to enter the user-level EXEC mode from the privileged EXEC mode:

WAE# disable
WAE>

Related Commands

enable

disk

To configure disks on a WAAS device, use the disk EXEC command.

disk delete-partitions diskname

disk delete-data-partitions

disk disk-name diskxx replace

disk insert diskname

disk recreate-raid

disk scan-errors diskname

Syntax Description

delete-partitions diskname

Deletes data on the specified logical disk drive. After using this command, the WAAS software treats the specified disk drive as blank. All previous data on the drive is inaccessible.

Specify the name of the disk from which to delete partitions (disk00, disk01). For RAID-5 systems, this option is not available because only one logical drive is available.

delete-data-partitions

Deletes all data partitions on all logical drives. After using this command, the WAAS software treats the specified disk partitions as blank. All previous data on the partitions is inaccessible.

Data partitions include the CONTENT, PRINTSPOOL, and GUEST partitions. These partitions include all DRE and CIFS cache files, print spool files, and any virtual blade images. If you want to keep virtual blade images, back them up before using this command by using the copy virtual-blade EXEC command.

disk-name diskxx replace

Shuts down the physical disk with the name diskxx (disk00, disk01, etc.) so that it can be replaced in the RAID-5 array.

Note This option is available only on RAID-5 systems.

insert diskname

Instructs the SCSI host to rescan the bus to detect and mount the newly inserted disk. Specify the name of the disk to be inserted (disk00, disk01).

Note This option is available only on WAE-612 and WAE-7326 models.

recreate-raid

Recreates the RAID-5 array.

Note This option is available only on RAID-5 systems.

scan-errors diskname

Scans SCSI or IDE disks for errors and remaps the bad sectors if they are unused. Specify the name of the disk to be scanned (disk00, disk01).

For RAID-5 systems, this command scans the logical RAID device for errors. On these systems, there is no diskname option.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The WAAS software supports hot-swap functionality for both failed disk replacement and scheduled disk maintenance. On the WAE-612 and WAE-7326, use the disk disk-name diskxx shutdown global configuration command to shut down a disk for scheduled disk maintenance. On the WAE-7341 and WAE-7371, use the disk disk-name diskxx replace EXEC command to shut down a disk. (For the scheduled disk maintenance procedure, see the Cisco Wide Area Application Services Configuration Guide, Chapter 14.)

The disk hot-swap functionality automatically disables a failed disk if the system detects one critical disk alarm. The software removes the failed disk automatically regardless of the setting for disk error-handling.

For WAE-7341 and WAE-7371 models, when you replace a failed disk that was automatically disabled by the software, the disk automatically returns to service. For WAE-612 and WAE-7326 models, when you replace a failed disk that was automatically disabled by the software, use the disk insert EXEC command to bring the disk back into service. For all other models, see the (config) disk disk-name command section.

To identify which disks have been identified as failed or bad, use the show disks failed-disk-id EXEC command. Do not reinsert any disk with a serial number shown in this list.


Note The show disks failed-disk-id command is not available on WAE-7341 and WAE-7371 models.


Use the disk delete-partitions EXEC command to remove all disk partitions on a single disk drive on a WAAS device or to remove the disk partition on the logical drive for RAID-5 systems.


Caution Be careful when using the disk delete-partitions EXEC command because the WAAS software treats the specified disk drive as blank. All previous data on the drive will become inaccessible.


Note When you use the disk delete-partitions EXEC command on the WAE-7341 or WAE-7371 models, the command deletes the entire logical volume. The individual disk name option is not available on these platforms.


Examples

The following example shows how to recreate the RAID-5 array:

WAE# disk recreate-raid

Related Commands

(config) disk disk-name

(config) disk error-handling

(config) disk logical shutdown

show disks

dnslookup

To resolve a host or domain name to an IP address, use the dnslookup EXEC command.

dnslookup {hostname | domainname}

Syntax Description

hostname

Name of DNS server on the network.

domainname

Name of domain.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following examples show how the dnslookup command is used to resolve the hostname myhost to IP address 172.31.69.11, abd.com to IP address 192.168.219.25, and an IP address used as a hostname to 10.0.11.0:

WAE# dnslookup myhost
official hostname: myhost.abc.com
          address: 172.31.69.11

WAE# dnslookup abc.com
official hostname: abc.com
         address: 192.168.219.25

WAE# dnslookup 10.0.11.0
official hostname: 10.0.11.0
          address: 10.0.11.0

Related Commands


enable

To access privileged EXEC commands, use the enable EXEC command.

enable

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels: user and privileged. To access privileged-level EXEC mode, enter the enable EXEC command at the user access level prompt and specify a privileged EXEC password (superuser or admin-equivalent password) when prompted for a password.

If using TACACS+ authentication, there is an enable password feature in TACACS+ that allows an administrator to define a different enable password for each administrative-level user. If an administrative-level user logs in to the WAAS device with a normal-level user account (privilege level of 0) instead of an admin or admin-equivalent user account (privilege level of 15), that user must enter the admin password to access privileged-level EXEC mode:

WAE> enable
Password: 

The above behavior occurs even if the WAAS users are using TACACS+ for login authentication.The disable command takes you from privileged EXEC mode to user EXEC mode.

Examples

The following example shows how to access privileged EXEC mode:

WAE> enable
WAE#

Related Commands

disable

exit

exit

To terminate privileged-level EXEC mode and return to the user-level EXEC mode, use the exit command.

exit

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

All modes

Device Modes

application-accelerator

central-manager

Usage Guidelines

The exit EXEC command is equivalent to pressing Ctrl-Z or entering the end command. Entering the exit command in the user level EXEC shell terminates the console or Telnet session.

Examples

The following example shows how to terminate privileged-level EXEC mode and return to the user-level EXEC mode:

WAE# exit
WAE>

Related Commands

(config) exit

find-pattern

To search for a particular pattern in a file, use the find-pattern command in EXEC mode.

find-pattern {binary reg-express filename | count reg-express filename | lineno reg-express filename | match reg-express filename | nomatch reg-express filename | recursive reg-express filename}

find-pattern case {binary reg-express filename | count reg-express filename | lineno reg-express filename | match reg-express filename | nomatch reg-express filename | recursive reg-express filename}

Syntax Description

binary reg-express filename

Does not suppress the binary output. Specifies the regular expression to be matched and the filename.

count reg-express filename

Prints the number of matching lines. Specifies the regular expression to be matched and the filename.

lineno reg-express filename

Prints the line number with output. Specifies the regular expression to be matched and the filename.

match reg-express filename

Prints the matching lines. Specifies the regular expression to be matched and the filename.

nomatch reg-express filename

Prints the nonmatching lines. Specifies the regular expression to be matched and the filename.

recursive reg-express filename

Searches a directory recursively. Specifies the regular expression to be matched and the filename.

case

Matches a case-sensitive pattern.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to search a file recursively for a case-sensitive pattern:

WAE# find-pattern case recursive admin removed_core
-rw-------    1 admin    root     95600640 Oct 12 10:27 /local/local1/core_dir/
core.3.0.0.b5.eh.2796
-rw-------    1 admin    root     97054720 Jan 11 11:31 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.14086
-rw-------    1 admin    root     96845824 Jan 11 11:32 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.14823
-rw-------    1 admin    root     101580800 Jan 11 12:01 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.15134
-rw-------    1 admin    root     96759808 Jan 11 12:59 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.20016
-rw-------    1 admin    root     97124352 Jan 11 13:26 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.8095

The following example shows how to search a file for a pattern and print the matching lines:

WAE# find-pattern match 10 removed_core
Tue Oct 12 10:30:03 UTC 2004
-rw-------    1 admin    root     95600640 Oct 12 10:27 /local/local1/core_dir/
core.3.0.0.b5.eh.2796
-rw-------    1 admin    root     101580800 Jan 11 12:01 /local/local1/core_dir/
core.cache.3.0.0.b131.cnbuild.15134

The following example shows how to search a file for a pattern and print the number of matching lines:

WAE# find-pattern count 10 removed_core
3

Related Commands

cd

dir

lls

ls

help

To obtain online help for the command-line interface, use the help EXEC command.

help

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC and global configuration

Device Modes

application-accelerator

central-manager

Usage Guidelines

You can obtain help at any point in a command by entering a question mark (?). If nothing matches, the help list will be empty, and you must back up until entering a ? shows the available options.

Two styles of help are provided:

Full help is available when you are ready to enter a command argument (for example, show ?) and describes each possible argument.

Partial help is provided when you enter an abbreviated command and you want to know what arguments match the input (for example, show stat?).

Examples

The following example shows how to display the output of the help EXEC command:

WAE# help
Help may be requested at any point in a command by entering a question mark '?'. If 
nothing matches, the help list will be empty and you must backup until entering a '?' 
shows the available options.

Two styles of help are provided:
1. Full help is available when you are ready to enter a command argument.
2. Partial help is provided when an abbreviated argument is entered.

Related Commands

(config) help

install

To install a new software image (such as the WAAS software) into flash on the WAAS device, use the install EXEC command.

install imagefilename

Syntax Description

imagefilename

Name of the .bin file you want to install.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The install command loads the system image into flash memory and copies components of the optional software to the software file system (swfs) partition.


Note If you are installing a system image that contains optional software, make sure that an SWFS partition is mounted on disk00.


To install a system image, copy the image file to the SYSFS directory local1. Before executing the install command, change the present working directory to the directory where the system image resides. When the install command is executed, the image file is expanded. The expanded files overwrite the existing files on the WAAS device. The newly installed version takes effect after the system image is reloaded.


Note The install command does not accept .pax files. Files should be of the type .bin (for example, cache-sw.bin). Also, if the release being installed does not require a new system image, then it may not be necessary to write to flash memory. If the newer version has changes that require a new system image to be installed, then the install command may result in a write to flash memory.


Close your browser and restart the browser session to the WAAS Central Manager, if you installed a new software image to the primary WAAS Central Manager.

Examples

The following example shows how to load the system image contained in the wae512-cache-300.bin file:

WAE# install wae512-cache-300.bin 

Related Commands

copy disk

reload

less

To display a file using the Less application, use the less EXEC command.

less file_name

Syntax Description

file_name

Name of the file to be displayed.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Less is a pager application that displays text files one page at a time. You can use Less to view the contents of a file, but not edit it. Less offers some additional features when compared to conventional text file viewer applications such as Type. These features include the following:

Backward movement—Allows you to move backward in the displayed text. Use k, Ctrl-k, y, or Ctrl-y to move backward. See the summary of Less commands for more details; to view the summary, press h or H while displaying a file in Less.

Searching and highlighting—Allows you to search for text in the file that you are viewing. You can search forward and backward. Less highlights the text that matches your search to make it easy to see where the match is.

Multiple file support—Allows you to switch between different files, remembering your position in each file. You can also do a search that spans all the files you are working with.

Examples

The following example shows how to display the text of the syslog.txt file using the Less application:

WAE# less syslog.txt

Related Commands

type

license add

To add a software license to a device, use the license add EXEC command.

license add license-name

Syntax Description

license-name

Name of the software license to add. The following license names are supported:

Transport—Enables basic DRE, TFO, and LZ optimization.

Enterprise—Enables the EPM, HTTP, MAPI, NFS, SSL, CIFS (WAFS), and Windows Print application accelerators, the WAAS Central Manager, and basic DRE, TFO, and LZ optimization.

Video—Enables the video application accelerator. Requires the Enterprise license to be configured first.

Virtual-Blade—Enables the virtualization feature. Requires the Enterprise license to be configured first.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to install the enterprise license:

WAE# license add Enterprise

Related Commands

clear arp-cache license

show license

lls

To view a long list of directory names, use the lls EXEC command.

lls [directory]

Syntax Description

directory

(Optional) Name of the directory for which you want a long list of files.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The lls command provides detailed information about files and subdirectories stored in the present working directory (including the size, date, time of creation, SYSFS name, and long name of the file). This information can also be viewed with the dir command.

Examples

The following example shows how to display a detailed list of the files in the current directory:

WAE# lls 
size          time of last change             name
--------------  -------------------------          -----------
          4096  Fri Feb 24 14:40:00 2006  <DIR>    actona
          4096  Tue Mar 28 14:42:44 2006  <DIR>    core_dir
          4096  Wed Apr 12 20:23:10 2006  <DIR>    crash
          4506  Tue Apr 11 13:52:45 2006           dbupgrade.log
          4096  Tue Apr  4 22:50:11 2006  <DIR>    downgrade
          4096  Sun Apr 16 09:01:56 2006  <DIR>    errorlog
          4096  Wed Apr 12 20:23:41 2006  <DIR>    logs
         16384  Thu Feb 16 12:25:29 2006  <DIR>    lost+found
          4096  Wed Apr 12 03:26:02 2006  <DIR>    sa
         24576  Sun Apr 16 23:54:30 2006  <DIR>    service_logs
          4096  Thu Feb 16 12:26:09 2006  <DIR>    spool
       9951236  Sun Apr 16 23:54:20 2006           syslog.txt
      10026298  Thu Apr  6 12:25:00 2006           syslog.txt.1
      10013564  Thu Apr  6 12:25:00 2006           syslog.txt.2
      10055850  Thu Apr  6 12:25:00 2006           syslog.txt.3
      10049181  Thu Apr  6 12:25:00 2006           syslog.txt.4
          4096  Thu Feb 16 12:29:30 2006  <DIR>    var
           508  Sat Feb 25 13:18:35 2006           wdd.sh.signed

Related Commands

dir

lls

ls

ls

To view a list of files or subdirectory names within a directory, use the ls EXEC command.

ls [directory]

Syntax Description

directory

(Optional) Name of the directory for which you want a list of files.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the ls directory command to list the filenames and subdirectories within a particular directory.

Use the ls command to list the filenames and subdirectories of the current working directory.

Use the pwd command to view the present working directory.

Examples

The following example shows how to display the files and subdirectories that are listed within the root directory:

WAE# ls
actona
core_dir
crash
dbupgrade.log
downgrade
errorlog
logs
lost+found
sa
service_logs
spool
syslog.txt
syslog.txt.1
syslog.txt.2
syslog.txt.3
var
wdd.sh.signed

Related Commands

dir

lls

pwd

mkdir

To create a directory, use the mkdir EXEC command.

mkdir directory

Syntax Description

directory

Name of the directory to create.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to create a new directory, oldpaxfiles:

WAE# mkdir /oldpaxfiles

Related Commands

cpfile

dir

lls

ls

pwd

rename

rmdir

mkfile

To create a new file, use the mkfile EXEC command.

mkfile filename

Syntax Description

filename

Name of the file that you want to create.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the mkfile EXEC command to create a new file in any directory of the WAAS device.

Examples

The following example shows how to create a new file, traceinfo, in the root directory:

WAE# mkfile traceinfo

Related Commands

cpfile

dir

lls

ls

mkdir

pwd

rename

ntpdate

To set the software clock (time and date) on a WAAS device using an NTP server, use the ntpdate EXEC command.

ntpdate {hostname | ip-address} [key {authentication-key}]

Syntax Description

hostname

NTP hostname.

ip-address

NTP server IP address.

key

(Optional) Specifies to use authentication with the NTP server.

authentication-key

Authentication key string to use with the NTP server authentication. This value must be between 0 and 4294967295.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the ntpdate command to find the current time of day and set the current time on the WAAS device to match. You must save the time to the hardware clock using the clock save command if you want to restore the time after a reload.

Examples

The following example shows how to set the software clock on the WAAS device using a NTP server:

WAE# ntpdate 10.11.23.40

Related Commands

clock

(config) clock

(config) ntp

show clock

show ntp

ping

To send echo packets for diagnosing basic network connectivity on networks, use the ping EXEC command.

ping {hostname | ip-address}

Syntax Description

hostname

Hostname of system to ping.

ip-address

IP address of system to ping.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To use the ping command with the hostname argument, make sure that DNS functionality is configured on the WAAS device. To force the timeout of a nonresponsive host, or to eliminate a loop cycle, press Ctrl-C.

Examples

The following example shows how to send echo packets to a machine with address 172.19.131.189 to verify its availability on the network:

WAE# ping 172.19.131.189
PING 172.19.131.189 (172.19.131.189) from 10.1.1.21 : 56(84) bytes of
data.
64 bytes from 172.19.131.189: icmp_seq=0 ttl=249 time=613 usec
64 bytes from 172.19.131.189: icmp_seq=1 ttl=249 time=485 usec
64 bytes from 172.19.131.189: icmp_seq=2 ttl=249 time=494 usec
64 bytes from 172.19.131.189: icmp_seq=3 ttl=249 time=510 usec
64 bytes from 172.19.131.189: icmp_seq=4 ttl=249 time=493 usec

--- 172.19.131.189 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max/mdev = 0.485/0.519/0.613/0.047 ms
WAE#

pwd

To view the present working directory on a WAAS device, use the pwd EXEC command.

pwd

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to display the current working directory:

WAE# pwd
/local1

Related Commands

cd

dir

lls

ls

reload

To halt the operation and perform a cold restart on a WAAS device, use the reload EXEC command.

reload [force | in m | cancel]

Syntax Description

force

(Optional) Forces a reboot without further prompting.

in m

(Optional) Schedules a reboot after a specified interval (1-10080 minutes).

cancel

(Optional) Cancels a scheduled reboot.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To reboot a WAAS device, use the reload command. If no configurations are saved to flash memory, you are prompted to enter configuration parameters upon a restart. Any open connections are dropped after you enter the reload command, and the file system is reformatted upon restart.

The reload command can include the option to schedule a reload of the software to take effect in a specified number of minutes. After entering this command, you are asked to confirm the reload by typing y and then confirm WCCP shutdown by typing y again (if WCCP is active).

You can use the cancel option to cancel a scheduled reload.

Examples

The following example shows how to halt the operation of the WAAS device and reboot with the configuration saved in flash memory. You are not prompted for confirmations during the process.

WAE# reload force

Related Commands

write

rename

To rename a file on a WAAS device, use the rename EXEC command.

rename oldfilename newfilename

Syntax Description

oldfilename

Original filename.

newfilename

New filename.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the rename command to rename any SYSFS file without making a copy of the file.

Examples

The following example shows how to rename the errlog.txt file to old_errlog.txt:

WAE# rename errlog.txt old_errlog.txt

Related Commands

cpfile

restore

To restore the device to its manufactured default status by removing the user data from the disk and flash memory, use the restore EXEC command.

restore {factory-default [preserve basic-config] | rollback}

Syntax Description

factory-default

Resets the device configuration and data to their manufactured default status.

preserve

(Optional) Preserves certain configurations and data on the device.

basic-config

(Optional) Selects basic network configurations.

rollback

Rolls back the configuration to the last functional software and device configuration.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the restore EXEC command to restore data on a disk and in flash memory to the factory default, while preserving particular time-stamp evaluation data, or to roll back the configuration to the last functional data and device configuration.

This command erases all existing content on the device; however, your network settings are preserved and the device is accessible through a Telnet and Secure Shell (SSH) session after it reboots.

Backing up the Central Manager Database

Before you use the restore factory-default command on your primary WAAS Central Manager or change over from the primary to a standby WAAS Central Manager, make sure that you back up the WAAS Central Manager database and copy the backup file to a safe location that is separate from the WAAS Central Manager. You must halt the operation of the WAAS Central Manager before you enter the backup and restore commands.


Caution The restore command erases user-specified configuration information stored in the flash image and removes data from a disk, user-defined disk partitions, and the entire Central Manager database. User-defined disk partitions that are removed include the SYSFS, WAAS, and PRINTSPOOLFS partitions. The configuration that is removed includes the starting configuration of the device.

By removing the WAAS Central Manager database, all configuration records for the entire WAAS network are deleted. If you do not have a valid backup file or a standby WAAS Central Manager, you must reregister every WAE with the WAAS Central Manager because all previously configured data is lost.

If you used your standby WAAS Central Manager to store the database while you reconfigured the primary, you can register the former primary as a new standby WAAS Central Manager.

If you created a backup file while you configured the primary WAAS Central Manager, you can copy the backup file to this newly reconfigured WAAS Central Manager.

Rolling Back the Configuration

You can roll back the software and configuration of a WAAS device to a previous version using the restore rollback command. You would roll back the software only in cases in which a newly installed version of the WAAS software is not functioning properly.

The restore rollback command installs the last saved WAAS.bin image on the system disk. A WAAS.bin image is created during software installation and stored on the system disk. If the WAAS device does not have a saved version, the software is not rolled back.


Note WAFS to WAAS migration is supported. Rollback from WAAS to WAFS is not supported.


Examples

The following examples show how to use the restore factory-default and restore factory-default preserve basic-config commands. Because configuration parameters and data are lost, prompts are given before initiating the restore operation to ensure that you want to proceed.

WAE# restore factory-default 
This command will wipe out all of data on the disks
and wipe out WAAS CLI configurations you have ever made. 
If the box is in evaluation period of certain product,
the evaluation process will not be affected though.

It is highly recommended that you stop all active services
before this command is run.

Are you sure you want to go ahead?[yes/no]

WAE# restore factory-default preserve basic-config 
This command will wipe out all of data on the disks
and all of WAAS CLI configurations except basic network 
configurations for keeping the device online.
The to-be-preserved configurations are network interfaces,
default gateway, domain name, name server and hostname.
If the box is in evaluation period of certain product,
the evaluation process will not be affected.

It is highly recommended that you stop all active services
before this command is run.

Are you sure you want to go ahead?[yes/no]

Note You can enter basic configuration parameters (such as the IP address, hostname, and name server) at this point, or you can enter these parameters later through entries in the command-line interface.


The following example shows how to verify that the restore command has removed data from the SYSFS, WAAS, and PRINTSPOOLFS partitioned file systems:

WAE# show disks details

Physical disk information:

  disk00: Normal                (h00 c00 i00 l00 - DAS)    140011MB(136.7GB)
  disk01: Normal                (h00 c00 i01 l00 - DAS)    140011MB(136.7GB)


Mounted filesystems:

  MOUNT POINT       TYPE       DEVICE           SIZE    INUSE     FREE USE%
  /                 root       /dev/root        35MB     30MB      5MB  85%
  /swstore          internal   /dev/md1        991MB    333MB    658MB  33%
  /state            internal   /dev/md2       3967MB     83MB   3884MB   2%
  /disk00-04        CONTENT    /dev/md4     122764MB     33MB 122731MB   0%
  /local/local1     SYSFS      /dev/md5       3967MB    271MB   3696MB   6%
  .../local1/spool  PRINTSPOOL /dev/md6        991MB     16MB    975MB   1%
  /sw               internal   /dev/md0        991MB    424MB    567MB  42%


Software RAID devices:

  DEVICE NAME  TYPE     STATUS                PHYSICAL DEVICES AND STATUS
  /dev/md0     RAID-1   NORMAL OPERATION      disk00/00[GOOD]  disk01/00[GOOD]
  /dev/md1     RAID-1   NORMAL OPERATION      disk00/01[GOOD]  disk01/01[GOOD]
  /dev/md2     RAID-1   NORMAL OPERATION      disk00/02[GOOD]  disk01/02[GOOD]
  /dev/md3     RAID-1   NORMAL OPERATION      disk00/03[GOOD]  disk01/03[GOOD]
  /dev/md4     RAID-1   NORMAL OPERATION      disk00/04[GOOD]  disk01/04[GOOD]
  /dev/md5     RAID-1   NORMAL OPERATION      disk00/05[GOOD]  disk01/05[GOOD]
  /dev/md6     RAID-1   NORMAL OPERATION      disk00/06[GOOD]  disk01/06[GOOD]
Currently content-filesystems RAID level is not configured to change.

The following example shows how to upgrade or restore an older version of the WAAS software. In the example, version Y of the software is installed (using the copy command), but the administrator has not switched over to it yet, so the current version is still version X. The system is then reloaded (using the reload command), and it verifies that version Y is the current version running.

The following example shows how to roll back the software to version X (using the restore rollback command), and reload the software:

WAE# copy ftp install server path waas.versionY.bin
WAE# show version
Cisco Wide Area Application Services Software (WAAS)
Copyright (c) 1999-2006 by Cisco Systems, Inc.
Cisco Wide Area Application Services Software Release 4.0.0 (build b340 Mar 25 2
006)
Version: fe611-4.0.0.340

Compiled 17:26:17 Mar 25 2006 by cnbuild

System was restarted on Mon Mar 27 15:25:02 2006.
The system has been up for 3 days, 21 hours, 9 minutes, 17 seconds.

WAE# show version last
	Nothing is displayed.
WAE# show version pending
WAAS 4.0.1 Version Y
WAE# reload
...... reloading ......
WAE# show version
Cisco Wide Area Application Services Software (WAAS)
...
WAE# restore rollback
WAE# reload
...... reloading ......

Because flash memory configurations were removed after the restore command was used, the show startup-config command does not return any flash memory data. The show running-config command returns the default running configurations.

Related Commands

reload

show disks

show running-config

show startup-config

show version

rmdir

To delete a directory on a WAAS device, use the rmdir EXEC command.

rmdir directory

Syntax Description

directory

Name of the directory that you want to delete.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the rmdir EXEC command to remove any directory from the WAAS file system. The rmdir command only removes empty directories.

Examples

The following example shows how to delete the oldfiles directory from the local1 directory:

WAE# rmdir /local1/oldfiles

Related Commands

cpfile

dir

lls

ls

mkdir

pwd

rename

scp

To copy files between network hosts, use the scp command.

scp [4][6][B][C][p][q][r][v] [c cipher] [F config-file] [i id-file] [o ssh_option] [P port] [S program]
[[
user @] host : file] [...] [[user-n @] host-n : file-n]

Syntax Description

4

(Optional) Forces this command to use only IPv4 addresses.

6

(Optional) Forces this command to use only IPv6 addresses.

B

(Optional) Specifies the batch mode. In this mode, the scp command does not ask for passwords or passphrases.

C

(Optional) Enables compression. The scp command passes this option to the ssh command to enable compression.

p

(Optional) Preserves the following information from the source file: modification times, access times, and modes.

q

(Optional) Disables the display of progress information.

r

(Optional) Recursively copies directories and their contents.

v

(Optional) Specifies the verbose mode. Causes the scp and ssh commands to print debugging messages about their progress. This option can be helpful when troubleshooting connection, authentication, and configuration problems.

c cipher

(Optional) Specifies the cipher to use for encrypting the data being copied. The scp command directly passes this option to the ssh command.

F config-file

(Optional) Specifies an alternative per-user configuration file for Secure Shell (SSH). The scp command directly passes this option to the ssh command.

i id-file

(Optional) Specifies the file containing the private key for RSA authentication. The scp command directly passes this information to the ssh command.

o ssh_option

(Optional) Passes options to the ssh command in the format used in ssh_config5. See the ssh command for more information about the possible options.

P port

(Optional) Specifies the port to connect to on the remote host.

S program

(Optional) Specifies the program to use for the encrypted connection.

user

(Optional) Username.

host

(Optional) Hostname.

file

(Optional) Name of the file to copy.


Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The scp command uses SSH for transferring data between hosts.

This command prompts you for passwords or pass phrases when needed for authentication.

Related Commands

ssh

script

To execute a script provided by Cisco or check the script for errors, use the script EXEC command.

script {check | execute} file_name

Syntax Description

check

Checks the validity of the script.

execute

Executes the script. The script file must be a SYSFS file in the current directory.

file_name

Name of the script file.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The script EXEC command opens the script utility, which allows you to execute Cisco-supplied scripts or check errors in those scripts. The script utility can read standard terminal input from the user if the script you run requires input from the user.


Note The script utility is designed to run only Cisco-supplied scripts. You cannot execute script files that lack Cisco signatures or that have been corrupted or modified.


Examples

The following example shows how to check for errors in the script file test_script.pl:

WAE# script check test_script.pl

setup

To configure basic configuration settings (general settings, device network settings, interception type, disk configuration, and licenses) on the WAAS device or to complete basic configuration after upgrading to the WAAS software, use the setup EXEC command.

setup

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

For instructions on using the setup command, see the Cisco Wide Area Application Services Quick Configuration Guide.

Examples

The following example shows how to access the first screen of the wizard when you enter the setup EXEC command on a WAAS device that is running the WAAS software:

WAE# setup
Step 1: The following defaults can be configured:
Device mode: Application-accelerator
Interception Method: Inline
Management Interface: InlineGroup 1/1
Autosense: yes
Timezone: UTC 0 0

To keep above defaults and continue configuration, press 'y'.
To change above defaults and continue configuration, press 'n' [y]:

show aaa accounting

To display the AAA accounting configuration information for a WAAS device, use the show aaa accounting EXEC command.

show aaa accounting

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the show aaa accounting EXEC command to display configuration information for the following AAA accounting types:

Exec shell

Command (for normal users and superusers)

System

Examples

Table 3-1 describes the fields shown in the show aaa accounting command display.

Table 3-1 Field Descriptions for the show aaa accounting Command 

Field
Description

Accounting Type

AAA accounting configuration for the following types of user accounts:

Exec

Command level 0

Command level 15

System

Record Event(s)

Configuration of the AAA accounting notice that is sent to the accounting server.

stop-only

WAAS device that sends a stop record accounting notice at the end of the specified activity or event to the TACACS+ accounting server.

start-stop

WAAS device that sends a start record accounting notice at the beginning of an event and a stop record at the end of the event to the TACACS+ accounting server.

The start accounting record is sent in the background. The requested user service begins regardless of whether the start accounting record was acknowledged by the TACACS+ accounting server.

wait-start

WAAS device that sends both a start and a stop accounting record to the TACACS+ accounting server. The requested user service does not begin until the start accounting record is acknowledged. A stop accounting record is also sent.

disabled

Accounting that is disabled for the specified event.

Protocol

Accounting protocol that is configured.


Related Commands

(config) aaa accounting

show accelerator

To display the status and configuration of the application accelerators, use the show accelerator EXEC command.

show accelerator [{cifs | detail | epm | http | mapi | nfs | ssl | video}]

Syntax Description

cifs

(Optional) Displays the status for the CIFS application accelerator.

detail

(Optional) Displays the license information, configuration state, and operational state for all accelerators, and additional accelerator and policy engine configuration.

epm

(Optional) Displays the status for the EPM application accelerator.

http

(Optional) Displays the status for the HTTP application accelerator.

mapi

(Optional) Displays the status for the MAPI application accelerator.

nfs

(Optional) Displays the status for the NFS application accelerator.

ssl

(Optional) Displays the status for the SSL application accelerator.

video

(Optional) Displays the status for the video application accelerator.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

Table 3-2 describes the fields shown in the show accelerator command display for all application accelerators. Specific application accelerators display additional configuration status information.

Table 3-2 Field Description for the show accelerator Command 

Field
Description

Accelerator

Name of the accelerator.

Licensed

Yes or No.

Config State

Accelerator is Enabled or Disabled.

Operational State

Shutdown, Initializing, Running, Cleaning Up, or Expired License.

Policy Engine Config Item: State

Registered (policy engine is communicating with the accelerator) or Not Registered (policy engine is not communicating with the accelerator; seen when the accelerator is disabled).

Policy Engine Config Item: Default Action

Drop or Use. Specifies the action to be taken if the accelerator refuses to handle the connection (because of overload or other reasons). Drop means the connection is dropped, and Use means the connection uses a reduced set of policy actions (such as TFO and DRE).

Policy Engine Config Item: Connection Limit

Connection limit. The limit configured by the accelerator which states how many connections may be handled before new connection requests are rejected.

Policy Engine Config Item: Effective Limit

Effective connection limit. The dynamic limit relating to how many connections may be handled before new connection requests are rejected. This limit is affected by resources that have been reserved, but not yet used.

Policy Engine Config Item: Keepalive timeout

Connection keepalive timeout in seconds. Keepalive messages are sent by each accelerator.


Related Commands

(config) accelerator cifs

(config) accelerator epm

(config) accelerator http

(config) accelerator mapi

(config) accelerator nfs

(config) accelerator ssl

(config) accelerator video

show statistics accelerator

show alarms

To display information about various types of alarms, their status, and history on a WAAS device, use the show alarms EXEC command.

show alarms critical [detail [support]]

show alarms detail [support]

show alarms history [start_num [end_num [detail [support]]]] | critical [start_num [end_num [detail [support]]]]

show alarms major [start_num [end_num [detail [support]]]]

show alarms minor [start_num [end_num [detail [support]]]]

show alarms status

Syntax Description

critical

Displays critical alarm information.

detail

(Optional) Displays detailed information for each alarm.

support

(Optional) Displays additional information about each alarm.

history

Displays information about the history of various alarms.

start_num

(Optional) Alarm number that appears first in the alarm history.

end_num

(Optional) Alarm number that appears last in the alarm history.

major

Displays information about major alarms.

minor

Displays information about minor alarms.

status

Displays the status of various alarms and alarm overload settings.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The Node Health Manager in the WAAS software enables WAAS applications to raise alarms to draw attention in error/significant conditions. The Node Health Manager, which is the data repository for such alarms, aggregates the health and alarm information for the applications, services, and resources (for example, disk drives) that are being monitored on the WAAS device. For example, this feature gives you a mechanism to determine if a WAE is receiving overwhelming number of alarms. These alarms are referred to as WAAS software alarms.

The WAAS software uses SNMP to report error conditions by generating SNMP traps. The following WAAS applications can generate a WAAS software alarm:

Node Health Manager (alarm overload condition)

System Monitor (sysmon) for disk failures

The three levels of alarms in the WAAS software are as follows:

Critical—Alarms that affect the existing traffic through the WAE and are considered fatal (the WAE cannot recover and continue to process traffic).

Major—Alarms that indicate a major service (for example, the cache service) has been damaged or lost. Urgent action is necessary to restore this service. However, other node components are fully functional and the existing service should be minimally impacted.

Minor—Alarms that indicate that a condition that will not affect a service has occurred, but that corrective action is required to prevent a serious fault from occurring.

You can configure alarms using the snmp-server enable traps alarms global configuration command.

Use the show alarms critical EXEC command to display the current critical alarms being generated by WAAS software applications. Use the show alarms critical detail EXEC command to display additional details for each of the critical alarms being generated. Use the show alarms critical detail support EXEC command to display an explanation about the condition that triggered the alarm and how you can find out the cause of the problem. Similarly, you can use the show alarms major and show alarms minor EXEC commands to display the details of major and minor alarms.

Use the show alarms history EXEC command to display a history of alarms that have been raised and cleared by the WAAS software on the WAAS device since the last software reload. The WAAS software retains the last 100 alarm raise and clear events only.

Use the show alarms status EXEC command to display the status of current alarms and the alarm overload status of the WAAS device and alarm overload configuration.

Examples

Table 3-3 describes the fields shown in the show alarms history command display.

Table 3-3 Field Descriptions for the show alarms history Command

Field
Description

Op

Operation status of the alarm. Values are R-Raised or C-Cleared.

Sev

Severity of the alarm. Values are Cr-Critical, Ma-Major, or Mi-Minor.

Alarm ID

Type of event that caused the alarm. For example: wafs_edge_down or wafs_core_down.

Module/Submodule

Software module affected. For example: wafs

Instance

Object that this alarm event is associated with. For example, for an alarm event with the Alarm ID disk_failed, the instance would be the name of the disk that failed. The Instance field does not have predefined values and is application specific.


Table 3-4 describes the fields shown in the show alarms status command display.

Table 3-4 Field Descriptions for the show alarms status Command 

Field
Description

Critical Alarms

Number of critical alarms.

Major Alarms

Number of major alarms.

Minor Alarms

Number of minor alarms.

Overall Alarm Status

Aggregate status of alarms.

Device is NOT in alarm overload state.

Status of the device alarm overload state.

Device enters alarm overload state @ 999 alarms/sec.

Threshold number of alarms per second at which the device enters the alarm overload state.

Device exits alarm overload state @ 99 alarms/sec.

Threshold number of alarms per second at which the device exits the alarm overload state.

Overload detection is ENABLED.

Status of whether overload detection is enabled on the device.


Related Commands

(config) alarm overload-detect

(config) snmp-server enable traps

show arp

To display the ARP table for a WAAS device, use the show arp EXEC command.

show arp

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the show arp command to display the Internet-to-Ethernet address translation tables of the Address Resolution Protocol. Without flags, the current ARP entry for the host name is displayed.

Examples

Table 3-5 describes the fields shown in the show arp command display.

Table 3-5 Field Descriptions for the show arp Command

Field
Description

Protocol

Type of protocol.

Address

IP address of the hostname.

Flags

Current ARP flag status.

Hardware Addr

Hardware IP address given as six hexadecimal bytes separated by colons.

Type

Type of wide-area network.

Interface

Name and slot/port information for the interface.


show authentication

To display the authentication configuration for a WAAS device, use the show authentication EXEC command.

show authentication {user | content-request}

Syntax Description

user

Displays authentication configuration for user login to the system.

content-request

Displays content request authentication configuration information in the disconnected mode.


s

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

When the WAAS device authenticates a user through an NTLM, LDAP, TACACS+, RADIUS, or Windows domain server, a record of the authentication is stored locally. As long as the entry is stored, subsequent attempts to access restricted Internet content by the same user do not require additional server lookups. To display the local and remote authentication configuration for user login, use the show authentication user EXEC command.

To display the content request authentication configuration information in the disconnected mode, use the show authentication content-request EXEC command.

Examples

Table 3-6 describes the fields shown in the show authentication user command display.

Table 3-6 Field Descriptions for the show authentication user Command 

Field
Description

Login Authentication: Console/Telnet/Ftp/SSH Session

Authentication service that is enabled for login authentication and the configured status of the service.

Windows domain

RADIUS

TACACS+

Local

Operation status of the authentication service. Values are enabled or disabled.

Priority status of each authentication service. Values are primary, secondary, or tertiary.

Configuration Authentication: Console/Telnet/Ftp/SSH Session

Authentication service that is enabled for configuration authentication and the configured status of the service.

Windows domain

RADIUS

TACACS+

Local

Operation status of the authentication service. Values are enabled or disabled.

Priority status of each authentication service. Values are primary, secondary, or tertiary.


Table 3-7 describes the field in the show authentication content-request command display.

Table 3-7 Field Description for the show authentication content-request Command

Field
Description

The content request authentication in disconnected mode is XXX.

Operation status of content request authentication in disconnected mode. Values are enabled or disabled.


Related Commands

(config) authentication configuration

clear arp-cache

show statistics authentication

show auto-discovery

To display Traffic Flow Optimization (TFO) auto-discovery information for a WAE, use the show auto-discovery EXEC command.

show auto-discovery {blacklist [netmask netmask] | list [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}]}

Syntax Description

blacklist

Displays the entries in the blacklist server table.

netmask netmask

(Optional) Displays the network mask to filter the table output (A.B.C.D/).

list

Lists TCP flows that the WAE is currently optimizing or passing through.

|

(Optional) Specifies the output modifier.

begin regex

Begins with the line that matches the regular expression. You can enter multiple expressions.

exclude regex

Excludes lines that match the regular expression. You can enter multiple expressions.

include regex

Includes lines that match the regular expression. You can enter multiple expressions.


Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following is sample output from the show auto-discovery list command:

WAE# show auto-discovery list

E: Established, S: Syn, A: Ack, F: Fin, R: Reset
s: sent, r: received, O: Options, P: Passthrough

      Src-IP:Port           Dst-IP:Port     Orig-St  Term-St

Related Commands

show statistics auto-discovery

show statistics filtering

show statistics tfo

show statistics connection closed

show auto-register

To display the status of the automatic registration feature on a WAE, use the show auto-register EXEC command.

show auto-register

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

Table 3-8 describes the output in the show auto-register command display.

Table 3-8 Field Description for the show auto-register Command

Field
Description

Auto registration is enabled.

Configuration status of the autoregistration feature.

Auto registration is disabled.

Configuration status of the autoregistration feature.


Related Commands

(config) auto-register

show banner

To display the message of the day (MOTD), login, and EXEC banner settings, use the show banner EXEC command.

show banner

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-9 describes the fields shown in the show banner command display.

Table 3-9 Field Descriptions for the show banner Command

Field
Description

Banner is enabled

Configuration status of the banner feature.

MOTD banner is: abc

Configured message of the day.

Login banner is: acb

Configured login banner.

Exec banner is: abc

Configured EXEC banner.


Related Commands

(config) auto-register

show bypass

To display static bypass configuration information for a WAE, use the show bypass EXEC command.

show bypass list

Syntax Description

list

Displays the bypass list entries. You can have a maximum of 50 entries.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

Table 3-10 describes the fields shown in the show bypass list command display.

Table 3-10 Field Descriptions for the show bypass list Command

Field
Description

Client

IP address and port of the client. For any client with this IP address, the WAE will not process the packet, but will bypass it and send it back to the router.

Server

IP address and port of the server.

Entry type

Type of bypass list entry. The Entry type field contains one of the following values: static-config, auth-traffic, server-error, or accept.

A static-config entry is a bypass list entry that is configured by the user. An auth-traffic entry is a type of dynamic entry that the internal software adds automatically when the server requests authentication.


Related Commands

(config) bypass

show cdp

To display CDP configuration information, use the show cdp EXEC command.

show cdp entry {* | neighbor} [protocol | version]

show cdp interface
[GigabitEthernet slot/port | InlinePort slot/port/{lan/wan}]

show cdp neighbors
[detail | GigabitEthernet slot/port [detail] | InlinePort slot/port/{lan/wan}[detail]]

show cdp {holdtime | run | timer | traffic}

Syntax Description

entry

(Optional) Displays information for a specific CDP neighbor entry.

*

Specifies all neighbors.

neighbor

The CDP neighbor entry to display.

protocol

(Optional) Displays the CDP protocol information.

version

(Optional) Displays the CDP version.

interface

Displays interface status and configuration.

GigabitEthernet slot/port

(Optional) Displays Gigabit Ethernet configuration (slot 1-2 and port number).

InlinePort slot/port/{lan/wan}

(Optional) Displays Inline Port configuration (slot 1-4, port number, LAN or WAN port).

neighbors

Displays CDP neighbor entries.

detail

(Optional) Displays detailed information.

holdtime

Displays the length of time that CDP information is held by neighbors.

run

Displays the CDP process status.

timer

Displays the time when CDP information is resent to neighbors.

traffic

Displays CDP statistical information.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show cdp command displays information about how frequently CDP packets are resent to neighbors, the length of time that CDP packets are held by neighbors, the disabled status of CDP Version 2 multicast advertisements, CDP Ethernet interface ports, and general CDP traffic information.

Examples

Table 3-11 describes the fields shown in the show cdp command display.

Table 3-11 Field Descriptions for the show cdp Command

Field
Description

Sending CDP packets every XX seconds

Interval (in seconds) between transmissions of CDP advertisements. This field is controlled by the cdp timer command.

Sending a holdtime value of XX seconds

Time (in seconds) that the device directs the neighbor to hold a CDP advertisement before discarding it. This field is controlled by the cdp holdtime command.

Sending CDPv2

advertisements is XX

Transmission status for sending CDP Version-2 type advertisements. Possible values are enabled or disabled.


Table 3-12 describes the fields shown in the show cdp entry neighbor command display.

Table 3-12 Field Descriptions for the show cdp entry Command 

Field
Description

Device ID

Name of the neighbor device and either the MAC address or the serial number of this device.

Entry address(es)

IP address

IP address of the neighbor device.

CLNS address

Non-IP network address. The field depends on the type of neighbor.

DECnet address

Non-IP network address. The field depends on the type of neighbor.

Platform

Product name and number of the neighbor device.

Interface

Protocol being used by the connectivity media.

Port ID (outgoing port)

Port number of the port on the neighbor device.

Capabilities

Capability code discovered on the neighbor device. This is the type of the device listed in the CDP Neighbors table. Possible values are as follows:

R—Router

T—Transparent bridge

B—Source-routing bridge

S—Switch

H—Host

I—IGMP device

r—Repeater

Holdtime

Time (in seconds) that the current device will hold the CDP advertisement from a transmitting router before discarding it.

Version

Software version running on the neighbor device.


Table 3-13 describes the fields shown in the show cdp entry neighbor protocol command display.

Table 3-13 Field Descriptions for the show cdp entry protocol Command

Field
Description

Protocol information for XX

Name or identifier of the neighbor device.

IP address

IP address of the neighbor device.

CLNS address

Non-IP network address. The field depends on the type of neighbor.

DECnet address

Non-IP network address. The field depends on the type of neighbor.


Table 3-14 describes the fields shown in the show cdp entry neighbor version command display.

Table 3-14 Field Descriptions for the show cdp entry version Command

Field
Description

Version information for XX

Name or identifier of the neighbor device.

Software, Version

Software and version running on the neighbor device.

Copyright

Copyright information for the neighbor device.


Table 3-15 describes the field in the show cdp holdtime command display.

Table 3-15 Field Descriptions for the show cdp holdtime Command

Field
Description

XX seconds

Time, in seconds, that the current device will hold the CDP advertisement from a transmitting router before discarding it.


Table 3-16 describes the fields shown in the show cdp interface command display.

Table 3-16 Field Descriptions for the show cdp interface Command

Field
Description

Interface_slot/port is XX

Operation status of the CDP interface. Values are up or down.

Encapsulation

Encapsulation.

Sending CDP packets every XX seconds

Time interval at which CDP packets are sent.

Holdtime

Time, in seconds, that the current device will hold the CDP advertisement from a transmitting router before discarding it.

CDP protocol is XX

Protocol being used by the connectivity media.


Table 3-17 describes the fields shown in the show cdp neighbors command display.

Table 3-17 Field Descriptions for the show cdp neighbors Command 

Field
Description

Device ID

Configured ID (name), MAC address, or serial number of the neighbor device.

Local Intrfce

(Local Interface) Protocol being used by the connectivity media.

Holdtime

Time, in seconds, that the current device will hold the CDP advertisement from a transmitting router before discarding it.

Capability

Capability code discovered on the device. This is the type of the device listed in the CDP Neighbors table. Possible values are as follows:

R—Router

T—Transparent bridge

B—Source-routing bridge

S—Switch

H—Host

I—IGMP device

r—Repeater

Platform

Product number of the device.

Port ID (outgoing port)

Port number of the device.


Table 3-18 describes the fields shown in the show cdp neighbors detail command display.

Table 3-18 Field Descriptions for the show cdp neighbors detail Command 

Field
Description

Device ID

Configured ID (name), MAC address, or serial number of the neighbor device.

Entry address (es)

List of network addresses of neighbor devices.

Platform

Product name and number of the neighbor device.

Capabilities

Device type of the neighbor. This device can be a router, a bridge, a transparent bridge, a source-routing bridge, a switch, a host, an IGMP device, or a repeater.

Interface

Protocol being used by the connectivity media.

Port ID (outgoing port)

Port number of the port on the neighbor device.

Holdtime

Time, in seconds, that the current device will hold the CDP advertisement from a transmitting router before discarding it.

Version

Software version running on the neighbor device.

Copyright

Copyright information for the neighbor device.

advertisement version

Version of CDP being used for CDP advertisements.

VTP Management Domain

VLAN trunk protocol management domain. The VLAN information is distributed to all switches that are part of the same domain.

Native VLAN

VLAN to which the neighbor interface belongs.


Table 3-19 describes the field in the show cdp run command display.

Table 3-19 Field Description for the show cdp run Command

Field
Description

CDP is XX.

Whether CDP is enabled or disabled.


Table 3-20 describes the field in the show cdp timer command display.

Table 3-20 Field Description for the show cdp timer Command

Field
Description

cdp timer XX

Time when CDP information is resent to neighbors.


Table 3-21 describes the fields shown in the show cdp traffic command display.

Table 3-21 Field Descriptions for the show cdp traffic Command 

Field
Description

Total packets Output

(Total number of packets sent) Number of CDP advertisements sent by the local device. This value is the sum of the CDP Version 1 advertisements output and CDP Version 2 advertisements output fields.

Input

(Total number of packets received) Number of CDP advertisements received by the local device. This value is the sum of the CDP Version-1 advertisements input and CDP Version 2 advertisements input fields.

Hdr syntax

(Header Syntax) Number of CDP advertisements with bad headers received by the local device.

Chksum error

(CheckSum Error) Number of times that the checksum (verifying) operation failed on incoming CDP advertisements.

Encaps failed

(Encapsulations Failed) Number of times that CDP failed to transmit advertisements on an interface because of a failure caused by the bridge port of the local device.

No memory

Number of times that the local device did not have enough memory to store the CDP advertisements in the advertisement cache table when the device was attempting to assemble advertisement packets for transmission and parse them when receiving them.

Invalid packet

Number of invalid CDP advertisements received and sent by the local device.

Fragmented

Number of times fragments or portions of a single CDP advertisement were received by the local device instead of the complete advertisement.

CDP version 1 advertisements Output

Number of CDP Version 1 advertisements sent by the local device.

Input

Number of CDP Version 1 advertisements received by the local device.

CDP version 2 advertisements Output

Number of CDP Version 2 advertisements sent by the local device.

Input

Number of CDP Version 2 advertisements received by the local device.


Related Commands

(config) cdp

(config-if) cdp

clear arp-cache

debug cdp

show cifs

To display legacy CIFS run-time information, use the show cifs EXEC command.

show cifs auto-discovery [enabled | host-db | last]

show cifs cache {disk-use | entry-count}

show cifs connectivity peers

show cifs mss

show cifs requests {count | waiting}

show cifs sessions {count | list}

Syntax Description

auto-discovery

Displays the CIFS auto-discovery status and run-time data.

enabled

(Optional) Displays current state of CIFS auto-discovery.

host-db

(Optional) Displays currently known hosts.

last

(Optional) Displays last auto-discovered entries.

cache

Displays CIFS cache information.

disk-use

Displays the total disk usage for CIFS cache.

entry-count

Displays the count of internal cache resources used for cached files.

connectivity

Displays Run-time information on Edge-Core connectivity.

peers

Displays a list of connected Cores.

mss

Displays the TCP maximum segment size (MSS) for the CIFS adapter. The segment size range is 512-1460.

requests

Displays run-time information on active CIFS requests.

count

Displays the number of pending CIFS requests.

waiting

Displays the number of waiting CIFS requests.

sessions

Displays run-time information on active CIFS sessions.

count

Displays the connected session count.

list

Displays the list of connected CIFS sessions.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

The show cifs command operates on legacy mode WAFS. For information on the transparent CIFS accelerator, use the show accelerator or show statistics accelerator commands.

Use the show cifs cache command to view information about caching efficiency. You might use this command to determine if the cache contains sufficient space or if more space is needed. If you have a performance issue, you might use this command to see whether or not the cache is full.

Use the show cifs connectivity peers command to validate the WAN link state and the Edge to Core connectivity. This command is useful for general monitoring and debugging.

Use the show cifs requests count or show cifs requests waiting command to monitor the load for CIFS traffic. You might also use this command for debugging purposes to isolate requests that are not processing.

Use the show cifs sessions count or show cifs sessions list command to view session information. You might use this command to monitor connected users during peak and off-peak hours.

Examples

The following is sample output from the show cifs connectivity peers command:

WAE# show cifs connectivity peers
In_533202151_2.43.60.38

Related Commands

cifs

show clock

To display information about the system clock on a WAAS device, use the show clock EXEC command.

show clock [detail | standard-timezones {all | details timezone | regions | zones region-name}]

Syntax Description

detail

(Optional) Displays detailed information; indicates the clock source (NTP) and the current summer time setting (if any).

standard-timezones

(Optional) Displays information about the standard time zones.

all

Displays all of the standard time zones (approximately 1500 time zones). Each time zone is listed on a separate line.

details timezone

Displays detailed information for the specified time zone.

regions

Displays the region name of all the standard time zones. All 1500 time zones are organized into directories by region.

zones region-name

Displays the name of every time zone that is within the specified region.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The WAAS device has several predefined standard time zones. Some of these time zones have built-in summer time information while others do not. For example, if you are in an eastern region of the United States (US), you must use the US/Eastern time zone that includes summer time information for the system clock to adjust automatically every April and October. There are about 1500 standard time zone names.

Strict checking disables the clock summertime command when you configure a standard time zone is configured. You can configure summer time only if the time zone is not a standard time zone (that is, if the time zone is a customized zone).

The show clock standard-timezones all EXEC command enables you to browse through all standard timezones and choose from these predefined time zones so that you can choose a customized name that does not conflict with the predefined names of the standard time zones. Most predefined names of the standard time zones have two components, a region name and a zone name. You can list time zones by several criteria, such as regions and zones. To display all first level time zone names organized into directories by region, use the show clock standard-timezones region EXEC command.

The show clock command displays the local date and time information and the show clock detail command shows optional detailed date and time information.

Examples

Table 3-22 describes the field in the show clock command display.

Table 3-22 Field Description for the show clock Command

Field
Description

Local time

Day of the week, month, date, time (hh:mm:ss), and year in local time relative to the UTC offset.


Table 3-23 describes the fields shown in the show clock detail command display.

Table 3-23 Field Descriptions for the show clock detail Command

Field
Description

Local time

Local time relative to UTC.

UTC time

Universal time clock date and time.

Epoch

Number of seconds since Jan. 1, 1970.

UTC offset

UTC offset in seconds, hours, and minutes.


Related Commands

clock

(config) clock

show cms

To display Centralized Management System (CMS) embedded database content and maintenance status and other information for a WAAS device, use the show cms EXEC command.

show cms {database content {dump filename | text | xml} | info | secure-store}

Syntax Description

database

Displays embedded database maintenance information.

content

Writes the database content to a file.

dump filename

Dumps all database content to a text file. Specifies the name of the file to be saved under local1 directory.

text

Writes the database content to a file in text format.

xml

Writes the database content to a file in XML format.

info

Displays CMS application information.

secure-store

Displays the status of the CMS secure store.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-24 describes the fields shown in the show cms info command display for WAAS application engines.

Table 3-24 Field Descriptions for the show cms info Command for WAAS Application Engines 

Field
Description

Device registration information

Device Id

Unique identifier given to the device by the Central Manager at registration, which is used to manage the device.

Device registered as

Type of device used during registration: WAAS Application Engine or WAAS Central Manager.

Current WAAS Central Manager

Address of the Central Manager as currently configured in the central-manager address global configuration command. This address may differ from the registered address if a standby Central Manager is managing the device instead of the primary Central Manager with which the device is registered.

Registered with WAAS Central Manager

Address of the Central Manager with which the device is registered.

Status

Connection status of the device to the Central Manager. This field may contain one of three values: online, offline, or pending.

Time of last config-sync

Time when the device management service last contacted the Central Manager for updates.

CMS services information

Service cms_ce is running

Status of the WAE device management service (running or not running). This field is specific to the WAE only.


Table 3-25 describes the fields shown in the show cms info command display for WAAS Central Managers.

Table 3-25 Field Descriptions for the show cms info Command for WAAS Central Managers 

Field
Description

Device registration information

Device Id

Unique identifier given to the device by the Central Manager at registration, which is used to manage the device.

Device registered as

Type of device used during registration: WAAS Application Engine or WAAS Central Manager.

Current WAAS Central Manager role

Role of the current Central Manager: Primary or Standby.

Note The output for primary and standby Central Manager devices is different. On a standby, the output includes the following additional information: Current WAAS Central Manager and Registered with WAAS Central Manager.

Current WAAS Central Manager

Address of the standby Central Manager as currently configured in the central-manager address global configuration command.

Registered with WAAS Central Manager

Address of the standby Central Manager with which the device is registered.

CMS services information

Service cms_httpd is running

Status of the management service (running or not running). This field is specific to the Central Manager only.

Service cms_cdm is running

Status of the management service (running or not running). This field is specific to the Central Manager only.


Table 3-26 describes the field in the show cms database content text command display.

Table 3-26 Field Description for the show cms database content text Command 

Field
Description

Database content can be found in /local1/cms-db-12-12-2002-17:06:08:070.txt.

Name and location of the database content text file. The show cms database content text command requests the management service to write its current configuration to an automatically generated file in text format.


Table 3-27 describes the field in the show cms database content xml command display.

Table 3-27 Field Description for the show cms database content xml Command

Field
Description

Database content can be found in /local1/cms-db-12-12-2002-17:07:11:629.xml.

Name and location of the database content XML file. The show cms database content xml command requests the management service to write its current configuration to an automatically generated file in XML format.


Related Commands

cms

(config) cms

show cms secure-store

To display secure store status, use the show cms secure-store EXEC command.

show cms secure-store

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show cms secure-store command will display one of the following status messages (Table 3-28):

Table 3-28 Status Messges for the show cms secure-store Command

Message
Description
secure-store not initialized

Secure store is not initialized.

secure-store is initialized, enter 
pass-phrase to open store

Secure store is initialized and not open.

secure-store initialized and open

Secure store is initialized and open.


Examples

The following is sample output from the show cms secure-store command:

WAE# show cms secure-store
secure-store initialized and open

Related Commands

cms secure-store

show crypto

To display crypto layer information, use the show crypto EXEC command.

show crypto {certificate-detail {factory-self-signed | management | filename} | certificates}

Syntax Description

certificate-detail

Displays a certificate in detail.

factory-self-signed

Displays WAAS self-signed certificates in detail.

management

Displays WAAS management certificates in detail.

filename

Filename of the certificate to display.

certificates

Displays a summary of all PKI certificates. This option can be used only on the WAE.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-29 describes the fields in the show crypto certificate-detail command display.

Table 3-29 Field Descriptions for the show crypto certificate-detail Command

Field
Description

Version

Certificate version.

Serial Number

Certificate serial number.

Signature Algorithm

Certificate signature algorithm.

Issuer

Information on the signer of the certificate.

Validity

Not Before

The date and time before which the certificate is not valid.

Not After

The date and time after which the certificate is not valid.

Subject

Information on the holder of the certificate.

Subject Public Key Info

Public Key Algorithm

Fields display X.509 certificate information as defined in RFC 5280.

RSA Public Key

Modulus

Exponent

X509v3 extensions

X509v3 Subject Key Identifier

Fields display X.509 certificate information as defined in RFC 5280.

X509v3 Authority Key Identifier

X509v3 Basic Constraints

Signature Algorithm

BEGIN CERTIFICATE

The actual certificate follows until the End Certificate line.

END CERTIFICATE

The line that signifies the end of the certificate.


Table 3-30 describes the fields in the show crypto certificates command display.

Table 3-30 Field Descriptions for the show crypto certificates Command

Field
Description

Certificate Only Store

Certificate Authority (CA) certificates.

Managed Store

User-defined certificates. Used under the server-cert-key section of SSL accelerated services. This certificate is used as a server certificate for client-to-WAE connections.

Local Store

Certificates that are configured on the WAE by default.

Machine Self signed Certificate

Certificate from the WAE to the server when client authentication is requested by the server.

Format

Format of the certificate (PEM or PKCS12).

Subject

The name of the holder of the certificate.

Issuer

Who signed the certificate.

Management Service Certificate

Certificate used to identify the WAE with the Central Manager.

Format

Format of the certificate (PEM or PKCS12).

EEC: Subject

The name of the holder of the certificate.

Issuer

Who signed the certificate.


Related Commands

show statistics crypto ssl ciphers

show debugging

To display the state of each debugging option that was previously enabled on a WAAS device, use the show debugging EXEC command.

show debugging

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show debugging command shows which debug options have been enabled or disabled. If there are no debug options configured, the show debugging command shows no output.

The dre, epm, flow, print-spooler, rbcp, tfo, translog, wafs, and wccp command options are supported in the application-accelerator device mode only. The emdb and rpc command options are supported in the central manager device mode only.

The show debugging command displays only the type of debugging enabled, not the specific subset of the command.

Examples

The following is sample output from the show debugging command:

WAE# debug tfo buffer-mgr
WAE# debug tfo connection
WAE# show debugging
tfo bufmgr debugging is on
tfo compmgr debugging is on
tfo connmgr debugging is on
tfo netio debugging is on
tfo statmgr debugging is on
tfo translog debugging is on

In this example, the debug tfo buffer-mgr and the debug tfo connection commands coupled with the show debugging command display the states of tfo buffer-mgr and tfo connection debugging options.

Related Commands

debug all

show device-mode

To display the configured or current device mode of a WAAS device, use the show device-mode EXEC command.

show device-mode {configured | current}

Syntax Description

configured

Displays the configured device mode, which has not taken effect yet.

current

Displays the current device mode.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To display the configured device mode that has not yet taken effect, enter the show device-mode configured EXEC command. For example, if you had entered the device mode central-manager global configuration command on a WAAS device to change its device mode to central manager but have not yet entered the copy run start EXEC command to save the running configuration on the device, then if you were to enter the show device-mode configured command on the WAAS device, the command output would indicate that the configured device mode is central-manager.

Examples

The following is sample output from the show device mode command. It displays the current mode in which the WAAS device is operating.

WAE# show device-mode current

Current device mode: application-accelerator

Table 3-31 describes the field in the show device-mode current command display.

Table 3-31 Field Description for the show device-mode current Command

Field
Description

Current device mode

Current mode in which the WAAS device is operating.


The following is sample output from the show device configured command. It displays the configured device mode that has not yet taken effect.

WAE# show device-mode configured

Configured device mode: central-manager

Table 3-32 describes the field in the show device-mode configured command display.

Table 3-32 Field Description for the show device-mode configured Command

Field
Description

Configured device mode

Device mode that has been configured, but has not yet taken effect.


Related Commands

(config) device mode

show directed-mode

To view the status and port assigned to directed mode on a device, use the show directed-mode EXEC command.

show directed-mode

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following is sample output from the show directed-mode EXEC command:

WAE# show directed-mode

Configuration Status:  Enabled
Config Item                          Mode           Value     
-----------                          ----           ------    
UDP port                             Default        4050      

This example shows that directed mode is enabled and it is using UDP port 4050.

Related Commands

show statistics directed-mode

show statistics connection closed

(config) directed-mode

show disks

To view information about the WAAS device disks, use the show disks EXEC command.

show disks {details | failed-disk-id | failed-sectors [disk_name] | tech-support [details]}

Syntax Description

details

Displays currently effective configurations with more details.

failed-disk-id

Displays a list of disk serial numbers that have been identified as failed.

Note This option is not available on WAE-7341 and WAE-7371 models.

failed-sectors

Displays a list of failed sectors on all the disks.

disk_name

(Optional) Name of the disk for which failed sectors are displayed (disk00 or disk01).

tech-support

Displays hard drive diagnostic information and information about impending disk failures.

Displays all available information from the RAID controller, including disk status (logical and physical), disk vendor ID, and serial numbers.

This command replaces the show disk smart-info EXEC command.

details

(Optional) Displays more detailed SMART disk monitoring information.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show disks details EXEC command displays the percentage or amount of disk space allocated to each file system, and the operational status of the disk drives, after reboot.

The WAAS software supports filtering of multiple syslog messages for a single, failed section on IDE, SCSI, and SATA disks.

Proactively Monitoring Disk Health with SMART

The ability to proactively monitor the health of disks is available using SMART. SMART provides you with hard drive diagnostic information and information about impending disk failures.

SMART is supported by most disk vendors and is a standard method used to determine how healthy a disk is. SMART attributes include several read-only attributes (for example, the power on hours attribute, the load and unload count attribute) that provide the WAAS software with information regarding the operating and environmental conditions that may indicate an impending disk failure.

SMART support is vendor and drive technology (IDE, SCSI, and Serial Advanced Technology Attachment [SATA] disk drive) dependent. Each disk vendor has a different set of supported SMART attributes.

Even though SMART attributes are vendor dependent there is a common way of interpreting most SMART attributes. Each SMART attribute has a normalized current value and a threshold value. When the current value exceeds the threshold value, the disk is considered to have "failed." The WAAS software monitors the SMART attributes and reports any impending failure through syslog messages, SNMP traps, and alarms.

To display SMART information, use the show disks tech-support EXEC command. To display more detailed SMART information, enter the show disks tech-support details EXEC command. The output from the show tech-support EXEC command also includes SMART information.

Examples

The following is sample output from the show disks failed-sectors command. It displays a list of failed sectors on all disk drives.

WAE# show disks failed-sectors
disk00
=========
89923
9232112

disk01
=========
(None)

The following is sample output from the show disks failed-sectors command when you specify a disk drive. It displays a list of failed sectors for disk01.

WAE# show disks failed-sectors disk01
disk01
=========
(None)

If there are disk failures, a message is displayed, notifying you about this situation when you log in.

Table 3-33 describes the fields shown in the show disks failed-disk-id command display.

Table 3-33 Field Description for the show disks failed-disk-id Command

Field
Description

Diskxx

Number and location of the physical disk.

Alpha-numeric string

Serial number of the disk.


Table 3-34 describes the fields shown in the show disks details command display.

Table 3-34 Field Descriptions for the show disks details Command 

Field
Description

Physical disk information or RAID Physical disk information

Lists the disks by number. On RAID-5 systems, this field is called RAID Physical disk information.

disk00

Availability of the disk: Present, Not present or Not responding, Not used (*), or Online (for RAID-5 disks).

Disk identification number and type, for example: (h00 c00i00 100 - DAS).

Disk size in megabytes and gigabytes, for example: 140011MB (136.7GB).

disk01

Same type of information is shown for each disk.

RAID Logical drive information

RAID-5 logical drive status and error conditions. (Only shown for RAID-5 systems.)

Mounted filesystems

Table containing the following column heads:

Mount point

Mount point for the file system. For example, the mount point for SYSFS is /local/local1.

Type

Type of the file system. Values include root, internal, CONTENT, SYSFS, and PRINTSPOOL.

Device

Path to the partition on the disk.

Size

Total size of the file system in megabytes.

Inuse

Amount of disk space being used by the file system.

Free

Amount of unused disk space for the file system.

Use%

Percentage of the total available disk space being used by the file system.

Software RAID devices

If present, lists the software RAID devices and provides the following information for each:

Device name

Path to the partition on the disk. The partition name "md1" indicates that the partition is a raided partition and that the RAID type is RAID-1.

Type

Type of RAID, for example RAID-1.

Status

Operational status of the RAID device. Status may contain NORMAL OPERATION or REBUILDING.

Physical devices and status

Disk number and operational status of the disk, such as [GOOD] or [BAD].

Disk encryption status

Indicates whether the disk encryption feature is enabled or disabled.


The following is sample output from the show disks tech-support command. The output shows that partition 04 and partition 05 on disks disk00 and disk01 are GOOD, and the RAIDed partitions /dev/md4 & /dev/md5 are in NORMAL OPERATION. However, the RAIDed partition /dev/md8 has an issue with one of the drives. Disk04 with partition 00 is GOOD, but the status shows ONE OR MORE DRIVES ABNORMAL because there is no pair on this partition.

WAE# show disks tech-support

/dev/md4     RAID-1   NORMAL OPERATION      disk00/04[GOOD]
disk01/04[GOOD]  
/dev/md5     RAID-1   NORMAL OPERATION      disk00/05[GOOD]
disk01/05[GOOD]  
...
/dev/md8     RAID-1   ONE OR MORE DRIVES ABNORMAL  disk04/00[GOOD]

Table 3-35 describes some typical fields in the show disks tech-support command display for a RAID-1 appliance that supports SMART. SMART attributes are vendor dependent; each disk vendor has a different set of supported SMART attributes.

Table 3-35 Field Descriptions for the show disks tech-support Command (RAID-1) 

Field
Description

disk00—disk05

WAE 7300 series appliances show information for 6 disk drives, and WAE 500 and 600 series appliances show information for 2 disk drives.

Device

Vendor number and version number of the disk.

Serial Number

Serial number for the disk.

Device type

Type of device is disk.

Transport protocol

Physical layer connector information, for example: Parallel SCSI (SPI-4).

Local time is

Day of the week, month, date, time hh:mm:ss, year, clock standard. For example, Mon Mar 19 23:33:12 2007 UTC.

Device supports SMART and is Enabled

Status of SMART support: Enabled or Disabled.

Temperature Warning Enabled

Temperature warning status: Enabled or Disabled.

SMART Health Status:

Health status of the disk: OK or Failed.


Table 3-36 describes the fields shown in the show disks tech-support command display for a RAID-5 appliance.

Table 3-36 Field Descriptions for the show disks tech-support Command (RAID-5)

Field
Description

Controllers found

Number of RAID controllers found.

Controller information

Controller Status

Functional status of the controller.

Channel description

Description of the channel transport protocols.

Controller Model

Make and model of the controller.

Controller Serial Number

Serial number of the ServeRAID controller.

Physical Slot

Slot number.

Installed memory

Amount of memory for the disk.

Copyback

Status of whether copyback is enabled or disabled.

Data scrubbing

Status of whether data scrubbing is enabled or disabled.

Defunct disk drive count

Number of defunct disk drives.

Logical drives/Offline/Critical

Number of logical drives, number of drives that are offline, and number of critical alarms.

Controller Version Information

BIOS

Version number of the BIOS.

Firmware

Version number of the Firmware.

Driver

Version number of the Driver.

Boot Flash

Version number of the Boot Flash.

Controller Battery Information

Status

Functional status of the controller battery.

Over temperature

Over temperature condition of the battery.

Capacity remaining

Percent of remaining battery capacity.

Time remaining (at current draw)

Number of days, hours, and minutes of battery life remaining based on the current draw.

Controller Vital Product Data

VPD Assigned#

Number assigned to the controller vital product data (VPD).

EC Version#

Version number.

Controller FRU#

Number assigned to the controller field-replaceable part.

Battery FRU#

Number assigned to the battery field-replaceable part.

Logical drive information

Logical drive number

Number identifying the logical drive to which the information applies.

Logical drive name

Name of the logical drive.

RAID level

RAID level of the logical drive.

Status of logical drive

Functional status of the logical drive.

Size

Size (in megabytes) of the logical drive.

Read-cache mode

Configuration status of read-cache mode: Enabled or Disabled.

Write-cache mode

Configuration status of write-cache mode for write-back: Enabled or Disabled.

Write-cache setting

Configuration status of the write-cache setting for write-back: Enabled or Disabled.

Partitioned

Partition state. Values are Yes or No.

Number of chunks

Number of disks participating in the RAID-5 array.

Stripe-unit size

Amount of data storage per stripe unit. The default is 256 KB per disk in the logical array. This parameter is not configurable.

Stripe order (Channel,Device)

Order in which data is striped across a group of physical drives that are grouped in a RAID array.

Bad stripes

Flag for bad stripes. Flag values are Yes or No.

Physical drive information

Device #

Device number for which the information applies.

Device is a xxxx

Type of device.

State

State of the device: Online or Offline.

Supported

Status showing if the device is supported.

Transfer Speed

Device transfer speed.

Reported Channel,Device

Provides channel information for all the disks participating in the RAID-5 array.

Reported Enclosure,Slot

Device number and slot number.

Vendor

Vendor identification number.

Model

Model number.

Firmware

Firmware number.

Serial number

Serial number.

Size

Size (in megabytes) of the physical drive.

Write Cache

Status of whether the write cache is enabled.

FRU

Field Replaceable Unit number. A RAID defunct drive FRU event occurs when a specified hard disk drive with the provided FRU number fails in a RAID configuration. The default value for this field is NONE.

PFA

Predictive Failure Analysis flag. The flag default value is No. If the RAID predicts a drive failure, this field is set to Yes and a critical alarm is raised on the WAE.


Table 3-37 describes the fields in the show disks tech-support details command display for a RAID-1 appliance that supports SMART. Details in this display depend on the drive manufacturer and vary between drives.

Table 3-37 Field Descriptions for the show disks tech-support details Command 

Field
Description

disk00—disk05

WAE 7300 series appliances show information for 6 disk drives and WAE 500 and 600 series appliances show information for 2 disk drives.

Device

Vendor number and version number of the disk.

Serial Number

Serial number for the disk.

Device type

Type of device is disk.

Transport protocol

Physical layer connector information, for example: Parallel SCSI (SPI-4).

Local time is

Day of the week, month, date, time hh:mm:ss, year, clock standard. For example, Mon Mar 19 23:33:12 2007 UTC.

Device supports SMART and is Enabled

Status of SMART support: Enabled or Disabled.

Temperature Warning Enabled

Temperature warning status: Enabled or Disabled.

SMART Health Status:

Health status of the disk: OK or Failed.

Current Drive Temperature

Temperature of the drive in degrees Celsius.

Manufactured in week XX of year

Manufacturing details.

Current start stop count

Number of times the device has stopped or started.

Recommended maximum start stop count

Maximum recommended count used to gauge the life expectancy of the disk.

Error counter log

Table displaying the error counter log. Counters for various types of disk errors.


Related Commands

disk

(config) disk error-handling

show tech-support

show egress-methods

To view the egress method that is configured and that is being used on a particular WAE, use the show egress-methods EXEC command.

show egress-methods

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

Table 3-38 describes the fields shown in the show egress-methods command display.

Table 3-38 Field Descriptions for the show egress-methods Command

Field
Description

Intercept method

Intercept method used by router to send packets to the WAE.

TCP Promiscuous 61 or 62

WCCP service number.

WCCP negotiated return method

WCCP return method being used by the router. Values include WCCP_GRE, WCCP_L2, NEG_RTN_PENDING (negotiation is pending), and UNKNOWN.

Destination

This value is not configurable. The value of this field is always ANY.

Egress Method Configured

Egress method configured in the CLI.

Egress Method Used

Egress method being used.


Related Commands

show tfo tcp

(config) egress-method

show filtering list

To display information about the incoming and outgoing TFO flows that the WAE currently has, use the show filtering list EXEC command.

show filtering list [| {begin regex [regex] | exclude regex [regex] | include regex [regex] }] [| {begin regex [regex] | exclude regex [regex] | include regex [regex]}]

Syntax Description

list

(Optional) Lists TCP flows that the WAE is currently optimizing or passing through.

|

(Optional) Output modifier.

begin regex

Begins with the line that matches the regular expression. You can enter multiple expressions.

exclude regex

Excludes lines that match the regular expression. You can enter multiple expressions.

include regex

Includes lines that match the regular expression. You can enter multiple expressions.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

The show filtering list command lists TCP flows that the WAE is currently optimizing. It also includes TCP flows that are not being optimized but that are being passed through by the WAE. A "P" in the State column indicates a passed through flow.

Examples

The following is sample output from the show filtering list command. It displays TFO connection information for the WAE.

WAE# show filtering list
E: Established, S: Syn, A: Ack, F: Fin, R: Reset
s: sent, r: received, O: Options, P: Passthrough
B: Bypass, L: Last Ack, W: Time Wait, D: Done
T: Timedout, C: Closed

    Local-IP:Port        Remote-IP:Port          Tuple(Mate)       State
   10.99.11.200:1398     10.99.22.200:80    0xcba709c0(0xcba70a00)   E
   10.99.11.200:1425     10.99.22.200:80    0xcba70780(0xcba707c0)   E
   10.99.11.200:1439     10.99.22.200:5222  0xcba703c0(0xcba70b40)   Sr
   10.99.11.200:1440     10.99.22.200:5222  0xcba70400(0xcba70440)   Sr
   10.99.22.200:1984     10.99.11.200:80    0xcba70600(0xcba70640)   E
   10.99.22.200:1800     10.99.11.200:23    0xcba70480(0x0       )   PE
   10.99.11.200:1392     10.99.22.200:80    0xcba70f80(0x0       )   E
   10.99.22.200:20       10.99.11.200:1417  0xcba701c0(0xcba70180)   E
   10.99.11.200:1417     10.99.22.200:20    0xcba70180(0x0       )   E
   10.99.22.200:1987     10.99.11.200:80    0xcba70240(0xcba70200)   E
   10.99.11.200:1438     10.99.22.200:5222  0xcba70900(0xcba70580)   Sr
   10.99.22.200:1990     10.99.11.200:80    0xcba70100(0xcba70140)   E
   10.99.22.200:80       10.99.11.200:1426  0xcba70740(0xcba70700)   E
   10.99.22.200:80       10.99.11.200:1425  0xcba707c0(0xcba70780)   E
   10.99.22.200:1985     10.99.11.200:80    0xcba70a40(0xcba70a80)   E
   10.99.22.200:80       10.99.11.200:1410  0xcba70500(0xcba70540)   E
   10.99.22.200:80       10.99.11.200:1398  0xcba70a00(0xcba709c0)   E
   10.99.22.200:80       10.99.11.200:1392  0xcba70f40(0xcba70f80)   E
   10.0.19.5:54247       10.1.242.5:80      0xc9e5b400(0xc9e5b100)   ED 


Note The "ED" state occurs when one socket in the pair is closed (D), but the mate is still established (E).


Related Commands

show accelerator

show statistics filtering

show statistics auto-discovery

show statistics connection closed

show flash

To display the flash memory version and usage information for a WAAS device, use the show flash EXEC command.

show flash

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-39 describes the fields shown in the show flash command display.

Table 3-39 Field Descriptions for the show flash Command

Field
Description

WAAS software version (disk-based code)

WAAS software version and build number that is running on the device.

System image on flash:

Version

Version and build number of the software that is stored in flash memory.

System flash directory:

System image

Number of sectors used by the system image.

Bootloader, rescue image, and other reserved areas

Number of sectors used by the bootloader, rescue image, and other reserved areas.

XX sectors total, XX sectors free

Total number of sectors. Number of free sectors.


show hardware

To display system hardware status for a WAAS device, use the show hardware EXEC command.

show hardware

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show hardware command lists the system hardware status, including the version number, the startup date and time, the run time since startup, the microprocessor type and speed, the amount of physical memory available, and a list of disk drives.

Examples

Table 3-40 describes the fields shown in the show hardware command display.

 

Table 3-40 Field Descriptions for the show hardware Command 

Field
Description

Cisco Wide Area Application Services Software (WAAS)

Copyright (c) year by Cisco Systems, Inc.

Cisco Wide Area Application Services Software Release XXX (build bXXX month day year)

Software application, copyright, release, and build information.

Version

Version number of the software that is running on the device.

Compiled hour:minute:second month day year by cnbuild

Compile information for the software build.

System was restarted on day of week month day hour:minute:second year

Date and time that the system was last restarted.

The system has been up for X hours, X minutes, X seconds

Length of time the system has been running since the last reboot.

CPU 0 is

CPU manufacturer information.

Total X CPU

Number of CPUs on the device.

XXXX Mbytes of Physical memory

Number of megabytes of physical memory on the device.

X CD ROM drive

Number of CD-ROM drives on the device.

X GigabitEthernet interfaces

Number of Gigabit Ethernet interfaces on the device.

X InlineGroup interfaces

Number of InlineGroup interfaces on the device.

X Console interface

Number of console interfaces on the device.

Manufactured As

Product identification information.

BIOS Information

Information about the BIOS.

Vendor

Name of the BIOS vendor.

Version

BIOS version number.

Rel. Date

(Release date) Date that the BIOS was released.

Cookie info

SerialNumber

Serial number of the WAE.

SerialNumber (raw)

Serial number of the WAE as an ASCII value.

TestDate

Date that the WAE was tested.

ExtModel

Hardware model of the device, for example WAE612.

ModelNum (raw)

Internal model number (ASCII value) that corresponds to the ExtModel number.

HWVersion

Number of the current hardware version.

PartNumber

Not implemented.

BoardRevision

Number of revisions for the current system board.

ChipRev

Number of revisions for the current chipset.

VendID

Vendor ID of the cookie.

CookieVer

Version number of the cookie.

Chksum

Checksum of the cookie. showing whether the cookie is valid.

List of all disk drives

Physical disk information

Disks listed by number. WAE 7300 series appliances show information for 6 disk drives and WAE 500 and 600 series appliances show information for 2 disk drives.

disk00

Availability of the disk: Present, Not present or not responding, or Not used (*).

Disk identification number and type, for example:(h00 c00i00 100 - DAS).

Disk size in megabytes and gigabytes, for example: 140011MB (136.7GB).

disk01

Same type of information is shown for each disk.

Mounted filesystems

Table containing the following column heads:

Mount point

Mount point for the file system. For example the mount point for SYSFS is /local/local1.

Type

Type of the file system. Values include root, internal, CONTENT, SYSFS, and PRINTSPOOL.

Device

Path to the partition on the disk.

Size

Total size of the file system in megabytes.

Inuse

Amount of disk space being used by the file system.

Free

Amount of unused disk space for the file system.

Use%

Percentage of the total available disk space being used by the file system.

Software RAID devices

If present, lists the software RAID devices and provides the following information for each:

Device name

Path to the partition on the disk. The partition name "md1" indicates that the partition is a raided partition and that the RAID type is RAID-1. (RAID-1 is the only RAID type supported in WAAS.)

Type

Type of RAID, for example RAID-1.

Status

Operational status of the RAID device. Status may contain NORMAL OPERATION or REBUILDING.

Physical devices and status

Disk number and operational status of the disk, such as [GOOD] or [BAD].


Related Commands

show disks

show version

show hosts

To view the hosts on a WAAS device, use the show hosts EXEC command.

show hosts

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show hosts command lists the name servers and their corresponding IP addresses. It also lists the hostnames, their corresponding IP addresses, and their corresponding aliases (if applicable) in a host table summary.

Examples

Table 3-41 describes the fields shown in the show hosts command display.

Table 3-41 field Descriptions for the show hosts Command

Field
Description

Domain names

Domain names used by the WAE to resolve the IP address.

Name Server(s)

IP address of the DNS name server or servers.

Host Table

hostname

FQDN (hostname and domain) of the current device.

inet address

IP address of the current host device.

aliases

Name configured for the current device based on the host global configuration command.


Related Commands

(config) ip hosts

show inetd

To display the status of TCP/IP services on a WAAS device, use the show inetd EXEC command.

show inetd

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show inetd EXEC command displays the enabled or disabled status of TCP/IP services on the WAAS device. You can ignore the TFTP service status because TFTP is not supported on WAAS.

Examples

Table 3-42 describes the fields shown in the show inetd command display.

Table 3-42 Field Descriptions for the show inetd Command

Field
Description

Inetd service configurations:

ftp

Status of whether the FTP service is enabled or disabled.

rcp

Status of whether the RCP service is enabled or disabled.

tftp

Status of whether the TFTP service is enabled or disabled.


Related Commands

(config) inetd

show interface

To display the hardware interface information for a WAAS device, use the show interface EXEC command.

show interface {GigabitEthernet slot/port} | {ide control_num} | {InlineGroup slot/grpnumber} | {InlinePort slot/grpnumber/{lan | wan}} | {PortChannel port-num} | {scsi device_num}
| {
standby 1 }

Syntax Description

GigabitEthernet slot/port

Displays the Gigabit Ethernet interface device information (only on suitably equipped systems). Slot and port number for the Gigabit Ethernet interface. The slot range is 0-3; the port range is 0-3. The slot number and port number are separated with a forward slash character (/).

ide control_num

Displays the IDE interface device information (controller number 0-1).

InlineGroup slot/grpnumber

Displays the inline group information. Slot and inline group number for the selected interface.

InlinePort

Displays the inline port information. Slot and inline group number for the selected interface.

lan

Displays the inline port information for the LAN port.

wan

Displays the inline port information for the WAN port.

PortChannel port-num

Displays the port channel interface device information (number 1).

scsi device_num

Displays the SCSI interface device information (number 0-7). (Not applicable on WAAS devices.)

standby 1

Displays the standby group information.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following is sample output from the show interface command. It displays information for inlineGroup 0 in slot 1 configured on the WAE inline network adapter.

WAE612# show interface inlineGroup 1/0
Interface is in intercept operating mode.
Standard NIC mode is off.
Disable bypass mode is off.
VLAN IDs configured for inline interception: All
Watchdog timer is enabled.
Timer frequency: 1600 ms.
Autoreset frequency 500 ms.
The watchdog timer will expire in 1221 ms.

Table 3-43 describes the fields shown in the show interface GigabitEthernet command display.

Table 3-43 Field Descriptions for the show interface GigabitEthernet Command 

Field
Description

Description

Description of the device, as configured by using the description option of the interface global configuration command.

Type

Type of interface. Always Ethernet.

Ethernet address

Layer-2 MAC address.

Internet address

Internet IP address configured for this interface.

Broadcast address

Broadcast address configured for this interface.

Netmask

Netmask configured for this interface.

Maximum Transfer Unit Size

Current configured MTU value.

Metric

Metric setting for the interface. The default is 1. The routing metric is used by the routing protocol to determine the most favorable route. Metrics are counted as additional hops to the destination network or host; the higher the metric value, the less favorable the route.

Packets Received

Total number of packets received by this interface.

Input Errors

Number of incoming errors on this interface.

Input Packets Dropped

Number of incoming packets that were dropped on this interface.

Input Packets Overruns

Number of incoming packet overrun errors.

Input Packets Frames

Number of incoming packet frame errors.

Packet Sent

Total number of packets sent from this interface.

Output Errors

Number of outgoing packet errors.

Output Packets Dropped

Number of outgoing packets that were dropped by this interface.

Output Packets Overruns

Number of outgoing packet overrun errors.

Output Packets Carrier

Number of outgoing packet carrier errors.

Output Queue Length

Output queue length in bytes.

Collisions

Number of packet collisions at this interface.

Interrupts

Number of packet interrupts at this interface.

Base address

Base address (hexidecimal value).

Flags

Interface status indicators. Values include Up, Broadcast, Running, and Multicast.

Link State

Interface and link status.

Mode

Speed setting, transmission mode, and transmission speed for this interface.


Table 3-44 describes the fields shown in the show interface InlinePort command display.

Table 3-44 Field Descriptions for the show interface InlinePort Command 

Field
Description

Device name

Number identifier for this inlineport interface, such as eth0, eth1, and so forth.

Packets Received

Total number of packets received on this inlineport interface.

Packets Intercepted

Total number of packets intercepted. (Only TCP packets are intercepted.)

Packets Bridged

Number of packets that are bridged. Packets which are not intercepted are bridged.

Packets Forwarded

Number of packets sent from the inline interface.

Packets Dropped

Number of packets dropped.

Packets Received on native

Number of packets forwarded by the inline module that are received on the native (GigabitEthernet 1/0) interface.

n flows through this interface

Number of active TCP connections on this inlineport interface.

Ethernet Driver Status

Type

Type of interface. Always Ethernet.

Ethernet address

Layer-2 MAC address.

Internet address

IP address (for WAN port only).

Broadcast address

Broadcast address (for WAN port only).

Netmask

Subnet mask (for WAN port only).

Maximum Transfer Unit Size

Current configured MTU value.

Metric

Metric setting for the interface. The default is 1. The routing metric is used by the routing protocol to determine the most favorable route. Metrics are counted as additional hops to the destination network or host; the higher the metric value, the less favorable the route.

Packets Received

Total number of packets received by this interface.

Input Errors

Number of incoming errors on this interface.

Input Packets Dropped

Number of incoming packets that were dropped on this interface.

Input Packets Overruns

Number of incoming packet overrun errors.

Input Packets Frames

Number of incoming packet frame errors.

Packet Sent

Total number of packets sent from this interface.

Output Errors

Number of outgoing packet errors.

Output Packets Dropped

Number of outgoing packets that were dropped by this interface.

Output Packets Overruns

Number of outgoing packet overrun errors.

Output Packets Carrier

Number of outgoing packet carrier errors.

Output Queue Length

Output queue length in bytes.

Collisions

Number of packet collisions at this interface.

Base address

Base address. hexidecimal value.

Flags

Interface status indicators. Values include Up, Broadcast, Running, and Multicast.

Link State

Interface and link status.

Mode

Speed setting, transmission mode, and transmission speed for this interface.


Table 3-45 describes the fields shown in the show interface PortChannel command display.

Table 3-45 Field descriptions for the show interface PortChannel Command 

Field
Description

Type

Type of interface. Always Ethernet.

Ethernet address

Layer-2 MAC address.

Maximum Transfer Unit Size

Current configured MTU value.

Metric

Metric setting for the interface. The default is 1. The routing metric is used by the routing protocol. Higher metrics have the effect of making a route less favorable; metrics are counted as addition hops to the destination network or host.

Packets Received

Total number of packets received by this interface.

Input Errors

Number of incoming errors on this interface.

Input Packets Dropped

Number of incoming packets that were dropped on this interface.

Input Packets Overruns

Number of incoming packet overrun errors.

Input Packets Frames

Number of incoming packet frame errors.

Packet Sent

Total number of packets sent from this interface.

Output Errors

Number of outgoing packet errors.

Output Packets Dropped

Number of outgoing packets that were dropped by this interface.

Output Packets Overruns

Number of outgoing packet overrun errors.

Output Packets Carrier

Number of outgoing packet carrier errors.

Output Queue Length

Output queue length in bytes.

Collisions

Number of packet collisions at this interface.

Flags

Interface status indicators. Values include Up, Broadcast, Running, and Multicast.

Link State

Interface and link status.


Table 3-46 describes the fields shown in the show interface standby command display.

Table 3-46 Field Descriptions for the show interface standby Command

Field
Description

Description

Description of the device, as configured by using the description option of the interface global configuration command.

Interface Standby 1

Number that identifies the standby group and the number of associated physical interfaces.

Member interfaces

Member interfaces of the standby group. Shows which physical interfaces are part of the standby group. Shows the interface definition, such as GigibitEthernet 1/0, and indicates if the interface is active (has an active layer 2 connection to a switch), primary (configured as primary in the running configuration), and in use (carrying network traffic).

Type

Type of interface. Always Ethernet.

. . .

The following fields are the same as for a gigabit Ethernet interface, as shown in Table 3-43.


Related Commands

(config) interface GigabitEthernet

show running-config

show startup-config

show inventory

To display the system inventory information for a WAAS device, use the show inventory EXEC command.

show inventory

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show inventory EXEC command allows you to view the UDI for a WAAS device. This identity information is stored in the nonvolatile memory of the WAAS device.

The UDI is electronically accessed by the product operating system or network management application to enable identification of unique hardware devices. The data integrity of the UDI is vital to customers. The UDI that is programmed into the nonvolatile memory of the WAAS device is equivalent to the UDI that is printed on the product label and on the carton label. This UDI is also equivalent to the UDI that can be viewed through any electronic means and in all customer-facing systems and tools. Currently, there is only CLI access to the UDI; there is no SNMP access to the UDI information.

You can also use the show tech-support EXEC command to display the WAAS device UDI.

Examples

Table 3-47 describes the fields shown in the show inventory command display.

Table 3-47 Field Descriptions for the show inventory Command

Field
Description

PID

Product identification (ID) number of the device.

VID

Version ID number of the device. Displays as 0 if the version number is not available.

SN

Serial number of the device.


Related Commands

show tech-support

show ip access-list

To display the access lists that are defined and applied to specific interfaces or applications on a WAAS device, use the show ip access-list EXEC command.

show ip access-list [acl-name | acl-num]

Syntax Description

acl-name

(Optional) Information for a specific access list, using an alphanumeric identifier up to 30 characters, beginning with a letter.

acl-num

(Optional) Information for a specific access list, using a numeric identifier (0-99 for standard access lists and100-199 for extended access lists).


Defaults

Displays information about all defined access lists.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the show ip access-list EXEC command to display the access lists that have been defined on the WAAS device. Unless you identify a specific access list by name or number, the system displays information about all the defined access lists, including the following sections:

Available space for new lists and conditions

Defined access lists

References by interface and application

Examples

Table 3-48 describes the fields shown in the show ip access-list command display.

Table 3-48 Field Descriptions for the show ip access-list Command 

Field
Description

Space available:

XX access lists

Number of access lists remaining out of 50 maximum lists allowed.

XXX access list conditions

Number of access list conditions remaining out of 500 maximum conditions allowed.

Standard IP access list

Name of a configured standard IP access list. Displays a list of the conditions configured for this list.

Extended IP access list

Name of a configured extended IP access list. Displays a list of the conditions configured for this list.

Interface access list references

List of interfaces and the access lists with which they are associated, displayed in the following format:

interface slot/port

interface direction

access list number

Application access list references

List of applications and the access lists with which they are associated, displayed in the following format:

application type

access list type and number

associated port


Related Commands

clear arp-cache

(config) ip access-list

show ip routes

To display the IP routing table for a WAAS device, use the show ip routes EXEC command.

show ip routes

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The show ip routes command displays the IP route table, which lists all of the different routes that are configured on the WAE. The WAE uses this table to determine the next hop. This table includes routes from three sources: the WAE GigabitEthernet interfaces, any user-configured static routes, and the default gateway. The last line in this table shows the default route.

Examples

Table 3-49 describes the fields shown in the show ip routes command display.

Table 3-49 Field Descriptions for the show ip routes Command

Field
Description

Destination

Destination IP addresses for each route.

Gateway

Gateway addresses for each route.

Netmask

Netmasks for each route.

Number of route cache entries

Number of entries in the route cache.

The route cache is a separate entity and this field is not associated with the entries in the IP route table. The number of entries in the route cache can vary depending on the number of connections that are open.


Related Commands

(config) ip

(config-if) ip

show kdump

To display the kernel crash dump information for a WAAS device, use the show kdump EXEC command.

show kdump

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-50 describes the fields shown in the show kdump command display.

Table 3-50 Field Descriptions for the show kdump Command

Field
Description

Kdump state

Enabled or not enabled.

Kdump operation

Operational or not operational.

Kdump crashkernel

Crash kernel information (Memory @ Base Address).


Related Commands

(config) kernel kdump

(config) logging console

show kerberos

To display the Kerberos authentication configuration for a WAAS device, use the show kerberos EXEC command.

show kerberos

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-51 describes the fields shown in the show kerberos command display.

Table 3-51 Field Descriptions for the show kerberos Command

Field
Description

Kerberos Configuration

Local Realm

Local realm name.

DNS suffix

DNS suffix for the realm.

Realm for DNS suffix

DNS addresses of the computers that are part of this realm.

Name of host running KDC for realm

Name of the host running the Key Distribution Center for the realm.

Master KDC

Primary or main Key Distribution Center.

Port

Port that the Kerberos server is using for incoming requests from clients. The default is port 88.


Related Commands

clear arp-cache

(config) logging console

show key-manager

To display the key manager information for a WAAS device, use the show key-manager EXEC command.

show key-manager {key-token | status}

Syntax Description

key-token

Displays the encryption key token for each registered WAE device.

status

Displays the encryption status for each registered WAE device.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

central-manager

Examples

Table 3-52 describes the fields shown in the show key-manager key-token command display. The set of fields is displayed for each key used on each WAE registered to the Central Manager.

Table 3-52 Field Descriptions for the show key-manager key-token Command

Field
Description

WAE Device

WAE device name.

Key Token

The encryption token.

Creation Time

Time the encryption key was created.

Encryption Algorithm

Type of encryption algorithm used.

Type

Type of key.


Related Commands

(config) disk encrypt

cms secure-store

show license

To display license information for a WAAS device, use the show license EXEC command.

show license

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following is sample output from the show license command. It lists the WAAS licenses, giving the name, status, date applied, and the name of the user that applied the license for each active license.

WAE# show license
License Name       Status       Activation Date       Activated by
----------------------------------------------------------------------
Transport          not active
Enterprise         active       11/12/2008            admin
Video              not active
Virtual-Blade      not active

Related Commands

clear arp-cache

license add

show logging

To display the system message log configuration for a WAAS device, use the show logging EXEC command.

show logging

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the system message log to view information about events that have occurred on a WAAS device. The syslog.txt file is contained in the /local1 directory.

Examples

The following is sample output from the show logging command. It displays the syslog host configuration on a WAAS device.

WAE# show logging
Syslog to host is disabled
Priority for host logging is set to:  warning

Syslog to console is disabled
Priority for console logging is set to:  warning

Syslog to disk is enabled
Priority for disk logging is set to:  notice
Filename for disk logging is set to:  /local1/syslog.txt

Syslog facility is set to *

Syslog disk file recycle size is set to 1000000

Related Commands

clear arp-cache

(config) logging console

show sysfs volumes

show memory

To display memory blocks and statistics for a WAAS device, use the show memory EXEC command.

show memory

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-53 describes the fields shown in the show memory command display.

Table 3-53 Field Descriptions for the show memory Command

Field
Description

Total physical memory

Total amount of system memory in kilobytes (KB), not including the amount reserved for the rescue kernel.

Total free memory

Total available memory (in kilobytes).

Total buffer memory

Total amount of memory (in kilobytes) in the memory buffer.

Total cached memory

Total amount of memory (in kilobytes) in the memory cache.

Total swap

Total amount of memory (in kilobytes) for swap purposes.

Total free swap

Total available memory (in kilobytes) for swap purposes.


show ntp

To display the NTP parameters for a WAAS device, use the show ntp EXEC command.

show ntp status

Syntax Description

status

Displays NTP status.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

Table 3-54 describes the fields shown in the show ntp status command display.

Table 3-54 Field Descriptions for the show ntp status Command 

Field
Description

NTP

Indicates whether NTP is enabled or disabled.

server list

NTP server IP and subnet addresses.

remote

Name (first 15 characters) of remote NTP server.

*

In the remote column, identifies the system peer to which the clock is synchronized.

+

In the remote column, identifies a valid or eligible peer for NTP synchronization.

space

In the remote column, indicates that the peer was rejected. (The peer could not be reached or excessive delay occurred in reaching the NTP server.)

x

In the remote column, indicates a false tick and is ignored by the NTP server.

-

In the remote column, indicates a reading outside the clock tolerance limits and is ignored by the NTP server.

refid

Clock reference ID to which the remote NTP server is synchronized.

st

Clock server stratum or layer. In this example, stratum 1 is the top layer.

t

Type of peer (local, unicast, multicast, or broadcast).

when

Indicates when the last packet was received from the server in seconds.

poll

Time check or correlation polling interval in seconds.

reach

8-bit reachability register. If the server was reachable during the last polling interval, a 1 is recorded; otherwise, a 0 is recorded. Octal values 377 and above indicate that every polling attempt reached the server.

delay

Estimated delay (in milliseconds) between the requester and the server.

offset

Clock offset relative to the server.

jitter

Clock jitter.


Related Commands

clock

(config) clock

(config) ntp

show policy-engine application

To display application policy information for a WAE, use the show policy-engine application EXEC command.

show policy-engine application {classifier [app-classifier] | dynamic | name}

Syntax Description

classifier

Displays information about the specified application classifier. If no classifier is specified, the show policy-engine applicaion command displays information about all classifiers. Every application classifier with a single match is displayed in one line.

app-classifier

(Optional) Name of an application classifier. The name should not exceed 30 characters.

dynamic

Shows the application dynamic match information.

name

Shows the application names list.


Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the show policy-engine application dynamic command to display auto-discovered CIFS file servers that are added to the list (for WAFS legacy mode only). The servers are visible in the dynamic listing for a limited time (3 minutes by default) after any activity stops, and then they are dropped from the dynamic list until another client request causes them to be auto-discovered again.

Examples

Table 3-55 describes the fields shown in the show policy-engine application classifier command display.

Table 3-55 Field Descriptions for the show policy-engine application classifier Command 

Field
Description

Number of Application Classifiers:

Number of application classifiers configured.

0 to N

Numbered list that includes the application name and the match statement that defines which traffic is interesting. For example:

0) AFS 
          match  dst port range 7000 7009

1) Altiris-CarbonCopy
         match   dst port eq 1680


Table 3-56 describes the fields shown in the show policy-engine application dynamic command display.

Table 3-56 Field Descriptions for the show policy-engine application dynamic Command

Field
Description

Dynamic Match Freelist Information

Allocated

Total number dynamic policies that can be allocated.

In Use

Number of dynamic matches that are currently in use.

Max In Use

Maximum number of dynamic matches that have been used since the last reboot.

Allocations

Number times that the dynamic match entries have been added.

Individual Dynamic Match Information:

Displays the internally-configured match values for dynamic applications. Dynamic applications do not use statically assigned ports, but they negotiate for a port to handle that application traffic.

Number

Number of the match condition in the list.

Type

Type of traffic to match. For example, Any-->Local tests traffic from any source to the local WAE.

User Id

Name of the accelerator that inserted the entry.

Src

Value for the source match condition. Values can be ANY, LOCAL, an IP address, or a port to which the application applies.

Dst

Value for the destination match condition. Values can be ANY, LOCAL, an IP address, or a port to which the application applies.

Map Name

Policy engine application map that is invoked if the dynamic match entry matches a connection.

Flags

Operation flags specifying different connection handling options.

Seconds

Number of seconds specified as the time limit for the dynamic match entry to exist.

Remaining

Number of seconds remaining before the dynamic match entry expires and is deleted.

Hits

Number of connections that have matched.


Table 3-57 describes the fields shown in the show policy-engine application name command display.

Table 3-57 Field Descriptions for the show policy-engine application name Command

Field
Description

Number of Applications: X

Number of applications defined on the WAE, including all of the default applications. WAAS includes over 150 default application policies. (For a list of default application policies, see the Cisco Wide Ar