Cisco Wide Area Applications Services Command Reference Guide 6.2.3

show wccp

clear bmc

To clear the BMC logs and events, use the clear bmc EXEC command.

clear bmc [ event-log ]

Syntax Description

event-log

Clears BMC system events and logs.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to clear the entries recorded in the BMC system event log on the WAAS device:

WAE# clear bmc event-log

Related Commands

show bmc

clear cache

To clear cached objects, use the clear cache EXEC command.

clear cache { dre}

clear cache http-metadatacache https {conditional-response | redirect-response | unauthorized-response }

clear cache http-metadatacache { all | conditional-response | redirect-response | unauthorized-response} [ url ]

Syntax Description

dre	Expires the DRE cache.
https	Clears cache entries for HTTPS metadata cache response types.
conditional-response	Clears cache entries for conditional responses (304).
redirect-response	Clears cache entries for redirect responses (301).
unauthorized-response	Clears cache entries for authorization required responses (401).
http-metadatacache	Clears the HTTP accelerator metadata cache.
all	Clears cache entries for all HTTP metadata cache response types.
url	Clears cache entries matching only the specified URL. If the URL string contains a question mark (?), it must be escaped with a preceding backslash (for example, \?).

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

After you use the clear cache dre command, the first 1 MB of data is not optimized. The Cisco WAAS software does not optimize the first 1 MB of data after a restart of the tcpproxy service. The data that is transmitted after the first 1 MB of data will be optimized according to the configured policy.

The clear cache dre command may cause the system to reboot, but you are asked to confirm before the command continues and you are given a chance to save any configuration changes that have been made to the running configuration.

The clear cache dre command does not delete the DRE cache contents but expires it by removing markers in the content to prevent reuse. If you want to delete the cache contents, use the disk delete-data-partitions command.

Examples

The following example shows how to clear the HTTP metadata cache for conditional responses:

WAE# clear cache http-metadatacache conditional-response

Related Commands

show cache http-metadatacache

show wccp

clear cache http-object-cache invalidate

To clear the object cache, use the clear cache http object-cache EXEC command.

clear cache http-object-cache invalidate

Command Default

No default behavior or values.

Command Modes

EXEC

Device Modes Default

application-accelerator

Usage Guidelines

This command clears all entries in the cache directory as a background task, but leaves entries up to 60 seconds prior to the command being given. It can take a few minutes to complete, but the CE is functional while the process is ongoing. Data on the disk remains and is not overwritten. Log entries appear indicating the beginning and end of the operation.

Examples

The following example shows how to clear the HTTP object cache:

WAE# clear cache http-object-cache invalidate

clear cdp

To clear Cisco Discovery Protocol statistics, use the clear cdp EXEC command.

clear cdp { counters | table }

Syntax Description

counters	Clears the CDP counters.
table	Clears the CDP tables.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the CDP counter statistics on the WAAS device:

WAE# clear cdp counters

Related Commands

show wccp

clear connection

To reset one or more connections, use the clear connection EXEC command.

clear connection [ client-ip { ip_address | hostname } | client-port port | flow-id id | server-ip { ip_address | hostname } | server-port port]

Syntax Description

client-ip	Resets the connections with the specified client IP address or hostname.
ip_address	IP address of a client or server.
hostname	Hostname of a client or server.
client-port port	Resets the connections with the specified client port number. The port number is from 1 to 65535.
flow-id id	Resets the connection with the specified number identifier.
server-ip	Resets the connections with the specified server IP address or hostname.
server-port port	Resets the connections with the specified server port number. The port number is from 1 to 65535.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to reset connection number 45 on the WAAS device:

WAE# clear connection flow-id 45

The following example shows how to reset connections with server port 80 on the WAAS device:

WAE# clear connection server-port 80

Related Commands

show statistics connection

clear dre

To clear DRE configurations, use the clear dre EXEC command.

clear dre auto-bypass [ { ip_address | hostname } port ]

Syntax Description

ip_address	(Optional) IP address of a server.
hostname	(Optional) Hostname of a server.
port	(Optional) A port number in the range from 1 to 65535.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear all DRE auto-bypass entries :

WAE# clear dre auto-bypass

The following example shows how to clear the DRE auto-bypass entry for a specific port on a specific server :

WAE# clear dre auto-bypass server 1.2.3.4 17

Related Commands

show dre

clear ip

To clear IP access list statistics, use the clear ip EXEC command.

clear ip access-list counters [ acl-num | acl-name ]

Syntax Description

access-list	Clears the access list statistical information.
counters	Clears the IP access list counters.
acl-num	(Optional) Counters for the specified access list, identified using a numeric identifier (standard access list: 1–99; extended access list: 100–199).
acl-name	(Optional) Counters for the specified access list, identified using an alphanumeric identifier of up to 30 characters, beginning with a letter.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the IP access list counters on the WAAS device:

WAE# clear ip access-list counters

Related Commands

show wccp

clear ipv6

To clear IPv6 neighbor cache entries, use the clear ipv6 neighbors EXEC command.

clear ipv6 neighbors {GigabitEthernet [slot number/port] | Portchannel [Etherchannel index] | standby [standby index] }

clear ipv6 neighbors virtual slot/port

Syntax Description

GigabitEthernet slot number/port	Clears the neighboring ipv6 cache entries for the GigabitEthernet interface.
PortChannel index	Clears the neighboring ipv6 cache entries for the EtherChannel device (1-4).
standby grpNumber	Clears the neighboring ipv6 cache entries for the standby device (1-2).
virtual	Clear neighboring ipv6 cache entries for Virtual Ethernet device (1-2)

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the neighboring cache entries for a GigabitEthernet interface on the WAAS device:

WAE# clear ipv6 neighbors GigabitEthernet 0/0

vWAAS# clear ipv6 neighbors virtual 1/0

Related Commands

show ipv6

show wccp

clear ip

clear license

To clear licensing configuration, use the clear license EXEC command.

clear license [ license-name ]

Syntax Description

license-name

Name of the software license to remove. The following license names are supported:

Transport—Enables basic DRE, TFO, and LZ optimization.
Enterprise—Enables the EPM, HTTP, MAPI, SSL, and Windows Print application accelerators, the WAAS Central Manager, and basic DRE, TFO, and LZ optimization. You cannot remove this license if the virtualization licenses are installed. You must remove both of those licenses first.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear the licensing configuration on the WAAS device:

WAE# clear license

Related Commands

show wccp

clear logging

To clear syslog messages saved in a disk file, use the clear logging EXEC command.

clear logging

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear logging command removes all current entries from the syslog.txt file but does not make an archive of the file. It puts a “Syslog cleared” message in the syslog.txt file to indicate that the syslog has been cleared.

Examples

The following example shows how to clear all entries in the syslog.txt file on the WAAS device:

WAE# clear logging

Feb 14 12:17:18 WAE# exec_clear_logging:Syslog cleared

Related Commands

clear statistics object-cache

show wccp

clear object-cache

To remove objects from object cache that match specified criteria, use the clear object-cache EXEC command.

clear object-cache [accelerator ao-name] all

clear object-cache [accelerator ao-name] server {server-ip server-ip | server-host hostname}

clear object-cache [accelerator ao-name] url path

Syntax Description

accelerator ao-name	(Optional) The name of the application accelerator specified, such as HTTP.
all	Clears all objects from the object cache. If you specify all, you will be prompted to confirm this action. Note that for WAAS Version 6.0, all is used only with accelerator HTTP.
server	Clears objects from the object cache of the server with the specified server IP address or hostname.
server-host hostname	Clears objects from the object cache of the specified server hostname.
server-ip server-ip	Clears objects from the object cache of the specified server IP address.
url path	Clears objects from the object cache for the specified URL. If the URL string contains a question mark (?), it must be escaped with a preceding backslash (for example, \?).

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes Default

application-accelerator

Usage Guidelines

The clear object-cache command removes all objects from the object cache, or all objects from cache that match specified criteria, such as AO name, server IP address or hostname, or path of a specified URL.

Examples

The following example shows how to clear objects from object cache that match the criteria of the SMB AO and the URL www.sampletestdomain.com.

WAE# clear object-cache accelerator http url www.sampletestdomain.com

Related Commands

clear service-policy

To clear class map and policy map counters for optimization policies, use the clear service-policy EXEC command.

clear service-policy [ type { waas }] counters

Syntax Description

type	Specifies the type of counters to clear.
waas	Clears WAAS optimization class map and policy map counters.
counters	Clears the class map and policy map counters.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

When specified without the type keyword, this command clears counters for WAAS optimization class maps and policy maps.

Examples

The following example shows how to clear WAAS optimization class map and policy map counters:

WAE# clear service-policy counters

Related Commands

show class-map

show policy-map

show statistics class-map

clear statistics

To reset statistics data, use the clear statistics EXEC command.

clear statistics { all | authentication | auto-discovery { all | blacklist } | class-map { waas } | datamover | dre [ global ] | exporter | filtering | flow monitor type performance-monitor tcpstat-v1 | generic-gre | icmp | inline | ip | ipv6 {internal} | pass-through | peer dre | punt | radius | | snmp | tacacs | tcp | tfo | udp | wccp | windows-domain | windows-print }

Syntax Description

all	Clears all statistics.
authentication	Clears authentication statistics.
auto-discovery	Clears the auto-discovery statistics.
blacklist	Clears the auto-discovery statistics for the blacklist.
class-map	Clears all class map statistics.
waas	Clears all statistics for WAAS class maps.
datamover	Clears all of the data mover statistics.
dre	Clears the Data Redundancy Elimination (DRE) statistics.
exporter	Clears the exporter statistics.
global	(Optional Clears the global DRE statistics.
filtering	Clears the filter table statistics.
flow	Clears the network traffic flow statistics.
monitor	Clears the monitor flow performance statistics.
tcpstat-v1	Clears the tcpstat-v1 collector statistics.
generic-gre	Clears the generic GRE statistics.
icmp	Clears the ICMP statistics.
inline	Clears the inline interception statistics.
ip	Clears the IP statistics.
ipv6	Clears IPv6 statistics.
pass-through	Clears all of the pass-through statistics.
peer dre	Clears all peer DRE statistics.
punt	Clears all the punt statistics.
radius	Clears the RADIUS statistics.
snmp	Clears the SNMP statistics.
tacacs	Clears the TACACS+ statistics.
tcp	Clears the TCP statistics.
tfo	Clears the TCP flow optimization (TFO) statistics.
udp	Clears the UDP statistics.
wccp	Clears all of the WCCP statistics.
windows-domain	Clears the Windows domain statistics.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear statistics command clears all statistical counters from the parameters given. Use this command to monitor fresh statistical data for some or all features without losing cached objects or configurations.

Not all command options are applicable for a device in central-manager mode.

Note that from software version 6.x onwards, clear statistics snmp does not clear all statistical counters due to net snmp implementation.

Examples

The following example shows how to clear all authentication, RADIUS and TACACS+ information on the WAAS device:

WAE# clear statistics radius

WAE# clear statistics tacacs

WAE# clear statistics authentication

Related Commands

clear statistics accelerator

clear statistics connection

clear statistics accelerator

To clear all global statistics, use the clear statistics accelerator EXEC command.

clear statistics accelerator { epm | generic | http | mapi | smb | ssl }

Syntax Description

epm	Clears the statistics for the EPM application accelerator.
generic	Clears the statistics for generic accelerator.
http	Clears the statistics for the HTTP application accelerator.
mapi	Clears the statistics for the MAPI application accelerator.
ssl	Clears the statistics for the SSL application accelerator.
smb	Clears the statistics for the SMB application accelerator, except for statistics on signed SMB bytes counters. To clear statistics for signed SMB bytes (read from/written to LAN, read from/written to WAN), use clear statistics accelerator generic, which clears all accelerator statistics, including signed SMB bytes counters.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to clear the statistics for the SMB application accelerator on the WAAS device:

WAE# clear statistics accelerator smb

Related Commands

clear statistics

clear statistics connection

clear statistics accelerator http object-cache

To clear object cache statistics for a WAAS device, use the clear statistics accelerator HTTP object-cache EXEC command.

clear statistics accelerator http object-cache

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

EXEC

Device Modes Default

application-accelerator

Usage Guidelines

Use this command to clear object cache statistics.

Example

The following example shows how to clear object cache statistics for a WAAS device.

WAE# clear statistics accelerator http object-cache

Related Commands

show statistics accelerator http object-cache

clear statistics connection

To clear connection statistics, use the clear statistics connection EXEC command.

clear statistics connection conn-id connection_id

clear statistics connection optimized [ client-ip { ip_address | hostname } | client-port port | { epm | http | ica | mapi | smb | ssl | tfo | wansecure } dre | peer-id peer_id | server-ip { ip_address | hostname } | server-port port]

Syntax Description

conn-id connection_id	Clears connection statistics for the connection with the specified number identifier.
optimized	Clears connection statistics for optimized connections.
client-ip	(Optional) Clears connection statistics for the client with the specified IP address or hostname.
ip_address	IP address of a client or server.
hostname	Hostname of a client or server.
client-port port	(Optional) Clears the connection statistics for the client with the specified port number. The port number is from 1 to 65535.
epm	(Optional) Clears connection statistics for connections optimized by the EPM application accelerator.
http	(Optional) Clears connection statistics for connections optimized by the HTTP application accelerator.
ica	(Optional) Clears connection statistics for connections optimized by the ICA application accelerator.
mapi	(Optional) Clears connection statistics for connections optimized by the MAPI application accelerator.
smb	(Optional) Clears connection statistics for connections optimized by the SMB application accelerator.
ssl	(Optional) Clears connection statistics for connections optimized by the SSL application accelerator.
tfo	(Optional) Clears connection statistics for connections optimized by the TFO application accelerator.
wansecure	(Optional) Clears connection statistics for connections optimized by the WAN secure application accelerator.
dre	(Optional) Clears connection statistics for connections optimized by the DRE feature.
peer-id peer_id	(Optional) Clears the connection statistics for the peer with the specified identifier. The peer ID is from 0 to 4294967295.
server-ip	(Optional) Clears the connection statistics for the server with the specified IP address or hostname.
server-port port	(Optional) Clears the connection statistics for the server with the specified port number. The port number is from 1 to 65535.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to clear the connection 1 statistics on the WAAS device:

WAE# clear statistics connection conn-id 1

Related Commands

clear statistics

clear statistics accelerator

clear statistics object-cache

To clear statistics from object cache, use the clear statistics object-cache EXEC command.

clear statistics object-cache

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

EXEC

Device Modes Default

application-accelerator

Usage Guidelines

The clear statistics object-cache command clears all statistical counters from the object cache.

Examples

The following example shows how to clear all statistics from the object cache:

WAE# clear statistics object-cache

Related Commands

clear object-cache

clear transaction-log

To archive a working transaction log file, use the clear transaction-log EXEC command.

clear transaction-log { accelerator | flow }

Syntax Description

accelerator	Clears the accelerator transaction log file.
flow	Clears the TFO transaction log.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to archive t he flow transaction log file on the WAAS device:

WAE# clear transaction-log flow

Related Commands

(config) authentication strict-password-policy

show wccp

clear users

To clear user connections or to unlock users that have been locked out, use the clear users EXEC command.

clear users [ administrative | locked-out { all | username username }]

Syntax Description

administrative	(Optional) Clears the connections (logins) of administrative users authenticated through a remote login service.
locked-out	(Optional) Unlocks specified locked-out user accounts.
all	Specifies all user accounts.
username username	Specifies the account username.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The clear users administrative command clears the connections for all administrative users who are authenticated through a remote login service, such as TACACS. This command does not affect an administrative user who is authenticated through the local database. Only locally authenticated administrative users can run this command.

The clear users locked-out command unlocks user accounts that have been locked out. If a strong password policy is enabled (see the (config) authentication strict-password-policy command) a user account will be locked out if the user fails three consecutive login attempts. (This restriction does not apply to the admin account.)

Examples

The following example shows how to clear the connections of all authenticated users:

WAE(config)# clear users

The following example shows how to clear the connections of all administrative users authenticated through a remote login service (it does not affect administrative users authenticated through the local database):

WAE(config)# clear users administrative

The following example shows how to unlock all locked-out user accounts:

WAE(config)# clear users locked-out all

The following example shows how to unlock the account for username darcy:

WAE(config)# clear users locked-out username darcy

Related Commands

clear arp-cache

clear windows-domain

To clear Windows domain server information for a WAAS device, use the clear windows-domain EXEC command.

clear windows-domain encryption-service blacklist { identity tagName | service spn }

Syntax Description

identity tagName	Clears identity information.
service spn	Clears service information.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the clear windows-domain EXEC command to clear Windows domain server information.

Examples

The following example shows how to clear the Windows domain server information:

WAE(config)# clear windows-domain encryption-service blacklist identity some-id

Related Commands

show windows-domain

clear windows-domain-log

To clear the Windows domain server log file, use the clear windows-domain-log EXEC command.

clear windows-domain-log

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to clear all entries in the Windows domain log file on the WAAS device:

WAE# clear windows-domain-log

Related Commands

show wccp

clock

To set clock functions or update the calendar, use the clock EXEC command.

clock { read-calendar | set time day month year | update-calendar }

Syntax Description

read-calendar	Reads the calendar and updates the system clock.
set time day month year	Sets the time and date. Current time in hh:mm:ss format (hh: 00–23; mm: 00–59; ss: 00–59). Day of the month (1–31). Month of the year (January, February, March, April, May, June, July, August, September, October, November, December). Year (1993–2035).
update-calendar	Updates the calendar with the system clock.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If you have an outside source on your network that provides time services (such as a NTP server), you do not need to set the system clock manually. When setting the clock, enter the local time. The WAAS device calculates the UTC based on the time zone set by the clock timezone global configuration command.

Two clocks exist in the system: the software clock and the hardware clock. The software uses the software clock. The hardware clock is used only at bootup to initialize the software clock.

The set keyword sets the software clock.

Examples

The following example shows how to set the software clock on the WAAS device:

WAE# clock set 13:32:00 01 February 2005

Related Commands

show clock

cms

To configure the Centralized Management System (CMS) embedded database parameters for a WAAS device, use the cms EXEC command.

cms { config-sync | deregister [ force ] | lcm { enable | disable } | maintenance { full | regular } | recover { identity word } | restore filename | validate }

cms database { backup {config} | create | delete

Syntax Description

config-sync	Sets the node to synchronize configuration with the WAAS Central Manager.
deregister	Removes the device registration record and its configuration on the WAAS Central Manager.
force	(Optional) Forces the removal of the node registration. This option is available only on WAEs and the standby Central Manager. If disk encryption is enabled, it is disabled and encrypted file systems are erased after a reload.
lcm	Configures local/central management on a WAAS device that is registered with the WAAS Central Manager.
enable	Enables synchronization of the WAAS network configuration of the device with the local CLI configuration.
disable	Disables synchronization of the WAAS network configuration of the device with the local CLI configuration.
maintenance	Cleans and reindexes the embedded database tables.
full	Specifies a full maintenance routine for the embedded database tables.
regular	Specifies a regular maintenance routine for the embedded database tables.
recover	Recovers the identity of a WAAS device.
identity word	Specifies the identity of the recovered device (identification key set on the Central Manager).
restore filename	Restores the database management tables using the backup local filename.
validate	Validates the database files.
database	Creates, backs up, deletes, restores, or validates the CMS-embedded database management tables or files.
backup	Backs up the database management tables.
config	Backs up only configuration tables.
create	Creates the embedded database management tables.
delete	Deletes the embedded database files.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the cms config-sync command to enable registered WAAS devices and standby WAAS Central Manager to contact the primary WAAS Central Manager immediately for a getUpdate (get configuration poll) request before the default polling interval of 5 minutes. For example, when a node is registered with the primary WAAS Central Manager and activated, it appears as Pending in the WAAS Central Manager GUI until it sends a getUpdate request. The cms config-sync command causes the registered node to send a getUpdate request at once, and the status of the node changes as Online.

Use the cms database create command to initialize the CMS database for a device that is already registered with the WAAS Central Manager. Then use the cms enable command to enable the CMS. For a device that is not registered with a WAAS Central Manager, use only the cms enable command to initialize the CMS database tables, register the node, and enable the CMS.

Note For a vWAAS device, the model type must be configured before enabling management services.

Before a node can join a WAAS network, it must first be registered and then activated. Activate the node by using the WAAS Central Manager GUI.

The cms deregister command removes the node from the WAAS network by deleting registration information and database tables.

The cms deregister force command forces the removal of the node from the WAAS network by deleting registration information and database tables. If disk encryption is enabled on the device, it is disabled after you confirm this action. All data in encrypted file systems and imported certificates and private keys for the SSL accelerator are lost after a reload.

To back up the existing management database for the WAAS Central Manager, use the cms database backup command. For database backups, specify the following items:

Location, password, and user ID
Dump format in PostgreSQL plain text syntax

The naming convention for backup files includes the time stamp and the WAAS version number.

After the backup is complete, use the copy disk ftp command to move the backup file to a remote system.

Note For information on the procedure to back up and restore the CMS database on the WAAS Central Manager, see the Cisco Wide Area Application Services Configuration Guide.

Note Do not run multiple instances of the cms database backup command simultaneously on a device. If a backup is in progress, you must wait for it to finish before using the command again.

When you use the cms recover identity word command when recovering lost registration information, or replacing a failed node with a new node that has the same registration information, you must specify the device recovery key that you configured in the Modifying Config Property, System.device.recovery.key window of the WAAS Central Manager GUI.

Note All CMS-related commands are disabled when running the cms restore command.

Use the lcm command to configure local/central management (LCM) on a WAE. The LCM feature allows settings that are configured using the device CLI or GUI to be stored as part of the WAAS network-wide configuration data (enable or disable).

When you enter the cms lcm enable command, the CMS process running on WAEs and the standby WAAS Central Manager detects the configuration changes that you made on these devices using CLIs and sends the changes to the primary WAAS Central Manager.

When you enter the cms lcm disable command, the CMS process running on the WAEs and the standby WAAS Central Manager does not send the CLI changes to the primary WAAS Central Manager. Settings configured using the device CLIs will not be sent to the primary WAAS Central Manager.

If LCM is disabled, the settings configured through the WAAS Central Manager GUI will overwrite the settings configured from the WAEs; however, this rule applies only to those local device settings that have been overwritten by the WAAS Central Manager when you have configured the local device settings. If you (as the local CLI user) change the local device settings after the particular configuration has been overwritten by the WAAS Central Manager, the local device configuration will be applicable until the WAAS Central Manager requests a full device statistics update from the WAEs (clicking the Force full database update button from the Device Dashboard window of the WAAS Central Manager GUI triggers a full update). When the WAAS Central Manager requests a full update from the device, the WAAS Central Manager settings will overwrite the local device settings.

Examples

The following example shows how to back up the cms database management tables on the WAAS Central Manager named waas-cm:

waas-cm# cms database backup

creating backup file with label `backup'

backup file local1/acns-db-9-22-2002-17-36.dump is ready. use `copy' commands to move the backup file to a remote host.

The following example shows how to validate the cms database management tables on the WAAS Central Manager named waas-cm:

waas-cm# cms database validate

Management tables are valid

Related Commands

(config) cms

show cms

cms secure-store

To configure secure store encryption, use the cms secure-store EXEC commands.

cms secure-store { init | open | change | clear | reset | mode { user-passphrase | auto-passphrase }}

Syntax Description

init	Initializes secure store encryption on the WAE device and opens the secure store. This option is valid only on WAE devices.
open	Activates secure store encryption (the WAAS device encrypts the stored data using secure store encryption). On WAEs, secure store encryption must already be initialized using the cms secure-store init command. This option is valid on all types of devices. On the Central Manager, this command is valid only when in user-provided passphrase mode and it prompts you to enter the secure store encryption pass phrase.
change	Changes the secure store encryption pass phrase and encryption key. On the Central Manager, this command prompts you to enter the current pass phrase, new pass phrase, and confirm the new pass phrase. The WAAS device uses the pass phrase to generate the encryption key for secure disk encryption. After this option is used, the Central Manager is in user-provided passphrase mode. This option is valid only on the primary Central Manager and WAE devices.
clear	Disables secure store encryption. This option is valid only on WAE devices. Note If a Windows Domain User Account Identity has been configured on the device or the device group for encrypted-mapi acceleration, you will not be able to clear the secure store on the device. You must remove the Windows domain user account identity configuration from the device or device group before you can clear secure store.
reset	Resets secure store to the uninitialized state. You must initialize but not open secure store encryption and you must be in user-provided passphrase mode, to use this option. This option is valid only on primary Central Manager devices.
mode	Sets the secure store mode of opening. This option is valid only on primary Central Manager devices.
user-passphrase	Sets secure store to require a user-provided pass phrase to open after a reboot.
auto-passphrase	Sets secure store to automatically open after a reboot by using a unique system-generated pass phrase.

Defaults

A new Central Manager is configured for auto-generated passphrase mode with the secure store open.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Secure store encryption provides strong encryption and key management for your WAAS system. The WAAS Central Manager and WAE devices use secure store encryption for handling passwords, managing encryption keys, and for data encryption.

On a new Central Manager, secure store is initialized and open and in auto-generated passphrase mode. The only options are to change the pass phrase (which sets the secure store to user-provided passphrase mode) or to change to user-provided passphrase mode. To change to user-provided passphrase mode, use the cms secure-store mode user-passphrase command.

Note There may be a delay of a few minutes for the any changes you submit with the cms secure-store command to take effect. There may also be a delay for any changes to take effect if you submit changes at the WAAS CM Configure > Security > Secure Store Settings window.

For secure store on the Central Manager, the data is encrypted using a key encryption key generated from the pass phrase with SHA-1 hashing and an AES 256-bit algorithm. When you enable secure store on a WAE device, the data is encrypted using a 256-bit key encryption key generated by SecureRandom, a cryptographically strong pseudorandom number. You can use your own password to enable secure store, but it is not necessary in auto-generated passphrase mode (the default), where the Central Manager generates a unique password automatically. A user-supplied password must conform to the following rules:

Be 8 to 64 characters in length
Contain characters only from the allowed set: A-Za-z0-9~%'!#$^&*()|;:,"<>/
Contain at least one digit
Contain at least one lowercase and one uppercase letter

If you are using the user-provided passphrase mode, when you reboot the Central Manager, you must manually reopen secure store using the cms secure-store open command. Until you open the secure store, a critical alarm is displayed on the Central Manager and services that use encryption (such as the SSL application accelerator) are not available. If you are using the auto-generated passphrase mode (the default), the Central Manager automatically opens the secure store after a reboot by using its own generated pass phrase.

The secure store passphrase mode on the primary Central Manager is replicated to the standby Central Manager (within the standard replication time). If the primary Central Manager is switched to auto-generated passphrase mode, the standby Central Manager secure store changes to the open state. If the primary Central Manager is switched to user-provided passphrase mode or the passphrase is changed, the standby Central Manager secure store changes to the initialized but not open state and an alarm is raised. You must manually open the secure store on the standby Central Manager.

When you enable secure store on a WAE, the WAE initializes and retrieves a new encryption key from the Central Manager. The WAE uses this key to encrypt user passwords and dynamic share credentials stored on the WAE. When you reboot the WAE after enabling secure store, the WAE retrieves the key from the Central Manager automatically, allowing normal access to the data that is stored in the WAAS persistent storage. If key retrieval fails, an alarm is raised and secure store will be in the initialized but not open state. You must open secure store manually.

If you have made any other CLI configuration changes on a WAE within the datafeed poll rate time interval (5 minutes by default) before you entered the cms secure-store command, you will lose those prior configuration changes and you will need to redo them.

Use the cms secure-store reset command if you reload a Central Manager that is configured in user-provided passphrase mode and you forget the secure store password. This command deletes all encrypted data, certificate and key files, and key manager keys. The secure store is left in the open state using auto-generated passphrase mode. For the complete procedure for resetting the secure store, see the “Resetting Secure Store Encryption on a Central Manager” section on page 9-17 in the Cisco Wide Area Application Services Configuration Guide.

Examples

The following example shows how to change the pass phrase mode of the secure store encryption on the WAAS Central Manager:

waas-cm# cms secure-store mode user-passphrase

Stopping cms.

Do you wish to switch to User-provided passphrase mode? [yes]/no :y

The passphrase must adhere to the following rules

*******************************************************************

* 1) Must be between 8 to 64 characters in length *

* 2) Allowed character set is A-Za-z0-9~%'!#$^&*()|;:,"<>/*

* 3) Must contain at least one digit *

* 4) Must contain at least one lowercase and one uppercase letter *

*******************************************************************

Enter new passphrase:

Confirm passphrase:

Starting cms.

Related CommandsRelated Commands

show cms secure-store

configure

To enter global configuration mode, use the configure EXEC command. You must be in global configuration mode to enter global configuration commands.

configure

To exit global configuration mode, use the end or exit commands. You can also press Ctrl-Z to exit from global configuration mode.

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to enable global configuration mode on a WAAS device:

WAE# configure

WAE(config)#

Related Commands

(config) end

(config) exit

copy cdrom

To copy software release files from a CD-ROM, use the copy cdrom EXEC command.

copy cdrom install filedir filename

Syntax Description

install filedir filename

Installs the software release from the directory location and filename specified.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy a software release file from a CD-ROM:

WAE# copy cdrom install

Related Commands

install

reload

write

copy compactflash

To copy software release files from a CompactFlash card, use the copy compactflash EXEC command.

copy compactflash install filename

Syntax Description

install filename

Installs a software release from an image filename.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy a software release file from a CompactFlash card:

WAE# copy compactflash install

Related Commands

install

reload

write

copy disk

To copy the configuration or image data from a disk to a remote location using FTP or to the startup configuration, use the copy disk EXEC command.

copy disk { ftp { hostname | ip-address } remotefiledir remotefilename localfilename | startup-config filename }

Syntax Description

ftp	Copies to a file on an FTP server.
hostname	Hostname of the FTP server.
ip-address	IP address of the FTP server.
remotefiledir	Directory on the FTP server to which the local file is copied.
remotefilename	Name of the local file once it has been copied to the FTP server.
localfilename	Name of the local file to be copied.
startup-config filename	Copies the existing configuration file from the disk to the startup configuration (NVRAM).

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy disk ftp EXEC command to copy files from a SYSFS partition to an FTP server. Use the copy disk startup-config EXEC command to copy a startup-configuration file to NVRAM.

Examples

The following example shows how to copy a startup-configuration file to NVRAM:

WAE# copy disk startup-config

Related Commands

install

reload

write

copy ftp

To copy software configuration or image data from an FTP server, use the copy ftp EXEC command.

copy ftp disk { hostname | ip-address } remotefiledir remotefilename localfilename

copy ftp install { hostname | ip-address } remotefiledir remotefilename

copy ftp wow-recovery { hostname | ip-address } remotefiledir remotefilename

Syntax Description

disk	Copies a file to a local disk.
hostname	Hostname of the specific server.
ip-address	IP (IPV4/IPv6) address of the specific server.
remotefiledir	Directory on the FTP server where the image file to be copied is located.
remotefilename	Name of the file to be copied.
localfilename	Name of the copied file as it appears on the local disk.
install	Copies the file from an FTP server and installs the software release or firmware file to the local device.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy ftp disk EXEC command to copy a file from an FTP server to a SYSFS partition on the WAAS device. To show progress, this command prints a number sign (#) for each 1 MB of data that is copied.

Use the copy ftp install EXEC command to install an image file from an FTP server on a WAAS device. Part of the image goes to a disk and part goes to flash memory. This command can also be used to install a BIOS or other firmware update by specifying the appropriate update file.

You can also use the copy ftp install EXEC command to redirect your transfer to a different location. A username and a password have to be authenticated with a primary domain controller (PDC) before the transfer of the software release file to the WAAS device is allowed.

To show progress, this command prints a number sign (#) for each 1 MB of data that is copied.

Examples

The following example shows how to copy an image file from an FTP server and install the file on the local device:

WAE# copy ftp install 10.1.1.1 cisco/waas/4.1 WAAS-4.1.1-k9.bin

Enter username for remote ftp server:biff

Enter password for remote ftp server:*****

Initiating FTP download...

printing one # per 1MB downloaded

Sending:USER biff

10.1.1.1 FTP server (Version) Mon Feb 28 10:30:36 EST

2000) ready.

Password required for biff.

Sending:PASS *****

User biff logged in.

Sending:TYPE I

Type set to I.

Sending:PASV

Entering Passive Mode (128,107,193,244,55,156)

Sending:CWD //ftp-sj.cisco.com/cisco/waas/4.0

CWD command successful.

Sending PASV

Entering Passive Mode (128,107,193,244,55,156)

Sending:RETR WAAS-4.1.1-k9.bin

Opening BINARY mode data connection for ruby.bin (87376881 bytes).

###################################################################################

writing flash component:

.................................................................

The new software will run after you reload.

The following example shows how to upgrade the BIOS. All output is written to a separate file (/local1/.bios_upgrade.txt) for traceability. The hardware-dependent files that are downloaded from Cisco.com for the BIOS upgrade are automatically deleted from the WAAS device after the BIOS upgrade procedure has been completed.

WAE# copy ftp install upgradeserver /bios/update53/derived/ bios.bin

Enter username for remote ftp server:myusername

Enter password for remote ftp server:*****

Initiating FTP download...

Primary BIOS flashed successfully

Cleanup BIOS related files that were downloaded....

The new software will run after you reload.

WAE#

Related Commands

install

reload

write

copy http

To copy configuration or image files from an HTTP server to the WAAS device, use the copy http EXEC command.

copy http install { hostname | ip-address } remotefiledir remotefilename [ port portnum ] [ proxy proxy_portnum ] [ username username password ]

Syntax Description

install	Copies the file from an HTTP server and installs the software release file to the local device.
hostname	Name of the HTTP server.
ip-address	IP (IPV4/IPv6) address of the HTTP server.
remotefiledir	Remote file directory.
remotefilename	Remote filename.
port portnum	(Optional) Specifies the port number (1–65535) to connect to the HTTP server (the default is 80).
proxy proxy_portnum	(Optional) Allows the request to be redirected to an HTTP proxy server. HTTP proxy server port number (1–65535).
username username password	(Optional) Specifies the username and password to access the HTTP proxy server.

Defaults

HTTP server port: 80

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy http install EXEC command to install an image file from an HTTP server and install it on a WAAS device. It transfers the image from an HTTP server to the WAAS device using HTTP as the transport protocol and installs the software on the device. Part of the image goes to a disk and part goes to flash memory. Use the copy http central EXEC command to download a software image into the repository from an HTTP server.

You can also use the copy http install EXEC commands to redirect your transfer to a different location or HTTP proxy server by specifying the proxy hostname | ip-address option. A username and a password have to be authenticated with a primary domain controller (PDC) before the transfer of the software release file to the WAAS device is allowed.

Examples

The following example shows how to copy an image file from an HTTP server and install the file on the WAAS device:

WAE# copy http install 10.1.1.1 //ftp-sj.cisco.com/cisco/waas/4.0 WAAS-4.0.0-k9.bin

Enter username for remote ftp server:biff

Enter password for remote ftp server:*****

Initiating FTP download...

printing one # per 1MB downloaded

Sending:USER biff

10.1.1.1 FTP server (Version) Mon Feb 28 10:30:36 EST

2000) ready.

Password required for biff.

Sending:PASS *****

User biff logged in.

Sending:TYPE I

Type set to I.

Sending:PASV

Entering Passive Mode (128,107,193,244,55,156)

Sending:CWD //ftp-sj.cisco.com/cisco/waas/4.0

CWD command successful.

Sending PASV

Entering Passive Mode (128,107,193,244,55,156)

Sending:RETR WAAS-4.0.0-k9.bin

Opening BINARY mode data connection for ruby.bin (87376881 bytes).

###################################################################################

writing flash component:

.................................................................

The new software will run after you reload.

WAE# copy ftp install upgradeserver /bios/update53/derived/ bios.bin

Enter username for remote ftp server:myusername

Enter password for remote ftp server:*****

Initiating FTP download...

Related Commands

install

reload

write

copy monitoring-log

To copy SMB statistics data to the local disk or an FTP server, use the copy monitoring-log EXEC command.

copy monitoring-log { disk filename | ftp { hostname | ip-address } remotefiledir remotefilename }

Syntax Description

disk filename	Copies the statistics in CSV format to the specified local disk file in the /local/local1 directory.
ftp	Copies the statistics in CSV format to the specified remote file on an FTP server.
hostname	Name of the FTP server.
ip-address	IP (IPV4/IPv6) address of the FTP server.
remotefiledir	Remote file directory.
remotefilename	Remote filename.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use this command to write the last 14 days of statistics data that has been collected by the stats-collector logging global configuration command. The data is written as a CSV file compressed in tar archive format.

Examples

The following example shows how to copy statistics data to an FTP server:

WAE# copy monitoring-log ftp 10.1.1.1 mydir mystats

Related Commands

(config) stats-collector logging

copy running-config

To copy a configuration or image data from the current configuration, use the copy running-config EXEC command.

copy running-config { disk filename | startup-config | tftp { hostname | ip-address } remotefilename }

Syntax Description

disk filename	Copies the current system configuration to a disk file. Specify the name of the file to be created on a disk.
startup-config	Copies the running configuration to startup configuration (NVRAM).
tftp	Copies the running configuration to a file on a TFTP server.
hostname	Hostname of the TFTP server.
ip-address	IP (IPV4/IPv6) address of the TFTP server.
remotefilename	Remote filename of the configuration file to be created on the TFTP server. Use the complete pathname.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy running-config EXEC command to copy the running system configuration of the WAAS device to a SYSFS partition, flash memory, or TFTP server. The copy running-config startup-config EXEC command is equivalent to the write memory EXEC command.

Examples

The following example shows how to copy the current system configuration to startup configuration (NVRAM):

WAE# copy running-config startup-config

Related Commands

install

reload

write

copy scp

To securely copy configuration or image files from a source to a destination location, use the copy scp EXEC command.

copy scp { { disk { hostname | ip-address} remote_dir remote_file local_file} | { install { hostname | ip-address } remote_dir remote_file }}

Syntax Description

disk	Copies the current system configuration to a disk file.
hostname	Hostname of the SCP server.
ip-address	IP (IPV4/IPv6) address of the SCP server.
remote_dir	Remote directory where the system information file is to be created on the SCP server.
remote_file	Remote filename of the system information file to be created on the SCP server.
local_file	Name of the copied file as it appears on the local disk.
install	Copies the file from a source server and installs the software release or firmware file to the local device.
hostname	Hostname of the SCP server.
ip-address	IP address of the SCP server.
remote_dir	Remote directory where the system information file is to be created on the SCP server.
remote_file	Remote filename of the system information file to be created on the SCP server.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy scp disk EXEC command to copy a file from an SCP server to a SYSFS partition on the WAAS device.

Use the copy scp install EXEC command to install a software release or firmware file from an SCP server on a WAAS device.

Examples

The following example shows how to securely install the software release or firmware file from a source to a destination location:

WAE#copy scp install 2.43.65.21 /work/admin ruby.test.bin

Enter usename for remote scp server: admin

WARNING!!!

READ THIS BEFORE ATTEMPTING TO LOGON

This System is for the use of authorized users only. Individuals

using this computer without authority, or in excess of their

authority, are subject to having all of their activities on this

system monitored and recorded by system personnel. In the course

of monitoring individuals improperly using this system, or in the

course of system maintenance, the activities of authorized users

may also be monitored. Anyone using this system expressly

consents to such monitoring and is advised that if such

monitoring reveals possible criminal activity, system personnel

may provide the evidence of such monitoring to law enforcement

officials.

Cisco Acceptable Use Policy:

http://wwwin.cisco.com/infosec/policies/acceptableuse.shtml

admin@2.43.65.21's password:

ruby.test.bin 100% |*****************************| 432 MB 00:13

Backing up existing version WAAS 5.1.0-b67, built on 02:20:49 Nov 29 2012 by damaster

Converting Manifest files... Done

Rebuilding image based on current software... Done

Backing up flash configuration... Done

Reclaiming unused flash safe state sectors...SSMGR RETURNING: 4 (Success)

Done.

Detected OE594

Installing phase3 bootloader...

Installing WAE 64-bit image.

buildsysimg: short write on /swstore/comp.basesystem: Inappropriate ioctl for device

/swstore/default_ruby_installer.sh: problem running buildsysimg

Remove /swstore/backup to free up space.

Installing system image to flash... The new software will run after you reload.

Related Commands

install

copy sysreport

copy tech-support

copy startup-config

To copy configuration or image data from the startup configuration, use the copy startup-config EXEC command.

copy startup-config { disk filename | running-config | tftp { hostname | ip-address } remotefilename }

Syntax Description

disk filename	Copies the startup configuration to a disk file. Specify the name of the startup configuration file to be copied to the local disk.
running-config	Copies the startup configuration to running configuration.
tftp	Copies the startup configuration to a file on a TFTP server.
hostname	Hostname of the TFTP server.
ip-address	IP (IPV4/IPv6) address of the TFTP server.
remotefilename	Remote filename of the startup configuration file to be created on the TFTP server. Use the complete pathname.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy startup-config EXEC command to copy the startup configuration file to a TFTP server or to a SYSFS partition.

Examples

The following example shows how to copy the startup configuration file to the running configuration:

WAE# copy startup-config running-config

Related Commands

install

reload

write

copy sysreport

To copy system troubleshooting information from the device, use the copy sysreport EXEC command.

copy sysreport disk filename [ start-date { day month | month day } year [ end-date { day month | month day } year ]]

copy sysreport ftp { hostname | ip-address } remotedirectory remotefilename [ start-date { day month | month day } year [ end-date { day month | month day } year ]]

copy sysreport scp { hostname | ip-address } remotedirectory remotefilename [ start-date { day month | month day } year [ end-date { day month | month day } year ]]

copy sysreport tftp { hostname | ip-address } remotefilename } [ start-date { day month | month day } year [ end-date { day month | month day } year ]]

copy sysreport usb filename [ start-date { day month | month day } year [ end-date { day month | month day } year ]]

Syntax Description

disk filename	Copies system information to a disk file. Specify the name of the file to be created on a disk. Note that.tar.gz is appended to the filename that you specify.
ftp	Copies system information to a FTP server.
hostname	Hostname of the server.
ip-address	IP(IPV4/IPv6) address of the server.
remotedirectory	Remote directory where the system information file is to be created on the server.
remotefilename	Remote filename of the system information file to be created on the server.
scp	Copies system information to a SCP server.
hostname	Hostname of the server.
ip-address	IP address of the server.
remotedirectory	Remote directory where the system information file is to be created on the server.
remotefilename	Remote filename of the system information file to be created on the server.
start-date	(Optional) Specifies the start date of the information in the generated system report.
day month	Start date day of the month (1–31) and month of the year (January, February, March, April, May, June, July, August, September, October, November, December). You can alternately specify the month first, followed by the day.
year	Start date year (1993–2035).
end-date	(Optional) Specifies the end date of information in the generated system report. If omitted, this date defaults to today. The report includes files through the end of this day.
day month	End date day of the month (1–31) and month of the year (January, February, March, April, May, June, July, August, September, October, November, December). You can alternately specify the month first, followed by the day.
year	End date year (1993–2035).
tftp	Copies system information to a TFTP server.
start-date	(Optional) Specifies the start date of the information in the generated system report.
day month	Start date day of the month (1–31) and month of the year (January, February, March, April, May, June, July, August, September, October, November, December). You can alternately specify the month first, followed by the day.
year	Start date year (1993–2035).
end-date	(Optional) Specifies the end date of information in the generated system report. If omitted, this date defaults to today. The report includes files through the end of this day.
usb filename	Copies system information to a USB flash drive installed in a WAVE-294/594/694/7541/7571/8541 device. Specify the name of the file to be created on the USB flash drive. Note that.tar.gz is appended to the filename that you specify.

Defaults

If end-date is not specified, today is used.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

A system report is a comprehensive report, which you must generate before contacting Cisco technical support. The system report contains output from many commands and system logs, including show commands, network and other statistics, graphs, log content, and configuration settings.

Note The copy sysreport command consumes significant CPU and disk resources and can adversely affect system performance while it is running. The system report can be from 30 MB to 100MB in size, or larger, depending on your system configuration.

Before you run the copy sysreport command:

– Before generating a system report, use the test command to run diagnostic tests, so that diagnostic information is also included in the system report.

– Before generating a system report on a WAAS CM or standby WAAS CM, make a database backup by using the cms database backup command.

To generate a system report and store it on an FTP server, use the following form of the sysreport command:

copy sysreport ftp server-ip

Generating the system report:

When you run the copy sysreport disk command, the system report must be saved to the local1 directory.

Note When you run the copy sysreport disk command, the system report save process differs depending on the version of WAAS you are running.

For WAAS versions 6.1.x and later, the copy sysreport disk command saves the system report to the present working directory. Therefore, you must be in the local1 directory path when you run the copy sysreport disk command. If you are not in the local1 directory, the error message “Could not generate sysreport in location your-current-location” is displayed.

To display your present working directory, use the pwd command. To change your directory, use the cd command.

For WAAS versions earlier than 6.1.x, the copy sysreport disk command saves the system report to the local1 directory, irregardless of your present working directory. Therefore, you can be in any system directory when you run the copy sysreport disk command, and the system report is saved to the local1 directory.

Storing the completed system report:

Because the system report is such a large file, after you run the copy sysreport disk command, move the report file out of the disk, to save significant disk space. To do this, follow these steps:

1. WAE# copy generatedSysreport-name ftp server-name
The generated system report is copied from the current disk location and a copy is stored to a non-current-disk destination.

2. WAE# delfile generatedSysreport-name
The original generated system report on the current disk is deleted.

Examples

The following example shows how to copy the system information to the file mysysinfo on the local WAAS device:

WAE# copy sysreport disk mysysinfo start-date 1 March 2016 end-date March 31 2016

The following example shows how to copy system information by FTP to the file myfile in the root directory of the FTP server named myserver:

WAE# copy sysreport ftp myserver / myfile start-date 1 March 2016 end-date March 31 2016

Related Commands

cms

pwd

test

copy system-status

To copy status information from the system for debugging, use the copy system-status EXEC command.

copy system-status disk filename

Syntax Description

disk filename

Specifies the name of the file to be created on the disk.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy system-status EXEC command to create a file on a SYSFS partition that contains hardware and software status information.

Examples

The following example shows how to copy the system status to a disk file:

WAE# copy system-status disk file1

Related Commands

install

reload

write

copy tech-support

To copy the configuration or image data from the system to use when working with Cisco TAC, use the copy tech-support EXEC command.

copy tech-support { disk filename | ftp { hostname | ip-address } remotedirectory remotefilename | scp { hostname | ip-address} remotedirectory remotefilename | tftp { hostname | ip-address } remotefilename }

Syntax Description

disk filename	Copies system information for technical support to a disk file. Specify the name of the file to be created on disk.
ftp	Copies system information for technical support to an FTP server.
hostname	Hostname of the server.
ip-address	IP (IPV4/IPv6) address of the server.
remotedirectory	Remote directory of the system information file to be created on the server. Use the complete pathname.
remotefilename	Remote filename of the system information file to be created on the server.
scp	Copies system information for technical support to an SCP server
hostname	Hostname of the server.
ip-address	IP address of the server.
remotedirectory	Remote directory of the system information file to be created on the server. Use the complete pathname.
remotefilename	Remote filename of the system information file to be created on the server.
tftp	Copies system information for technical support to a TFTP server.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the copy tech-support tftp EXEC command to copy technical support information to a TFTP server or to a SYSFS partition.

Examples

The following example shows how to copy system information for tech support to a disk file:

WAE# copy tech-support disk file1

Related Commands

install

reload

write

copy tftp

To copy configuration or image data from a TFTP server, use the copy tftp EXEC command.

copy tftp disk { hostname | ip-address } remotefilename localfilename

copy tftp running-config { hostname | ip-address } remotefilename

copy tftp startup-config { hostname | ip-address } remotefilename

Syntax Description

disk	Copies an image from a TFTP server to a disk file.
hostname	Hostname of the TFTP server.
ip-address	IP (IPV4/IPv6) address of the TFTP server.
remotefilename	Name of the remote image file to be copied from the TFTP server. Use the complete pathname.
localfilename	Name of the image file to be created on the local disk.
running-config	Copies an image from a TFTP server to the running configuration.
startup-config	Copies an image from a TFTP server to the startup configuration.

Defaults

No default behaviors or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to copy configuration or image data from a TFTP server to the running configuration:

WAE# copy tftp running-config

Related Commands

install

reload

write

cpfile

To make a copy of a file, use the cpfile EXEC command.

cpfile oldfilename newfilename

Syntax Description

oldfilename	Name of the file to copy.
newfilename	Name of the copy to be created.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Only SYSFS files can be copied.

Examples

The following example shows how to create a copy of a file:

WAE# cpfile fe512-194616.bin fd512-194618.bin

Related Commands

deltree

dir

lls

mkdir

pwd

rename

crypto delete

To remove SSL certificate and key files, use the crypto delete EXEC command.

crypto delete {ca-certificate filename | pkcs12 {filename | admin }}

Syntax Description

ca-certificate filename	Deletes a certificate authority certificate file.
pkcs12 filename	Deletes a PKCS12 format file. (PKCS12 files contain both the private encryption key and the public key certificate.)
admin	Deletes the certificate and key for the Central Manager admin service, if a custom certificate and key were installed. This option can be used only on the Central Manager.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the crypto delete EXEC command to remove a certificate from your WAE’s secure store. If you only want to disassociate a certificate from an accelerated service, use no server-cert-key in crypto ssl services accelerated-service mode.

If you use the crypto delete pkcs12 admin command to delete a custom certificate and key that were installed for the Central Manager admin service, the admin service uses its built-in self-signed certificate.

Examples

The following example shows how to delete the CA certificate file mycert.ca:

WAE# crypto delete ca-certificate mycert.ca

Related Commands

crypto export

To export SSL certificate and key files, use the crypto export EXEC command.

crypto export {ca-certificate filename | pkcs12 { factory-self-signed | admin | filename} {pem-cert-key | pem-cert-only | pem-key-only | pkcs12}}{disk pathname | ftp address | sftp address | terminal | tftp address}

Syntax Description

ca-certificate filename	Exports a certificate authority certificate file.
pkcs12	Exports a PKCS12 format file. (PKCS12 files contain both the private encryption key and the public key certificate.)
factory-self-signed	Specifies that the SSL PKCS file is to be self-signed.
admin	Specifies that the certificate and key are for the Central Manager admin service. This option can be used only on the Central Manager.
filename	Name of the PKCS12 file to be exported.
pem-cert-key	Exports both the certificate and key in PEM format.
pem-cert-only	Exports only the certificate in PEM format.
pem-key-only	Exports only the key in PEM format.
pkcs12	Exports both the certificate and key in PKCS12 format.
disk pathname	Exports to a disk. Type the disk filename including the full path.
ftp address	Exports to FTP. Type the FTP server’s IP address or hostname.
sftp address	Exports to secure FTP. Type the secure FTP server’s IP address or hostname.
terminal	Exports to a terminal. (Not available for crypto export pkcs12.)
tftp address	Exports to TFTP. Type the TFTP server’s IP address or hostname.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to export a CA certificate file named mycert.ca to an FTP server:

WAE# crypto export ca-certificate mycert.ca ftp 1.2.3.4 dir1 mycert.ca

The following example shows how to export the certificate and private key from a PKCS12 file named myfile.p12 to a PEM file on the local1 directory on the hard drive:

WAE# crypto export pkcs12 myfile.p12 pkcs12 disk /local1/myfile.p12

Related Commands

crypto delete

crypto generate

To generate a self-signed certificate or a certificate signing request, use the crypt generate EXEC command.

crypto generate {csr rsa modulus {1024 | 1536 | 2048 | 512 | 768}{disk pathname | ftp address | sftp address | terminal | tftp address} | self-signed-cert filename [exportable] rsa modulus {1024 | 1536 | 2048 | 512 | 768}}

Syntax Description

csr rsa modulus	Generates a certificate signing request (CSR)
rsa modulus	Generates a self-signed certificate.
1024 \| 1536 \| 2048 \| 512 \| 768	Specifies the size (number of bits) used for the RSA modulus for a CSR or a self-signed certificate. Note The valid size for the RSA modulus for a self-signed certificate is dependent on the WAAS Version used. Refer to the crypto generate command Usage Guidelines for how to specify the RSA modulus size for WAAS Version 6.1.x and earlier, and for WAAS Version 6.2.x and later.
disk pathname	Generates the file to a disk. Type the disk filename including the full path.
ftp address	Generates the file to FTP. Type the FTP server’s IP address or hostname.
sftp address	Generates the file to secure FTP. Type the secure FTP server’s IP address or hostname.
terminal	Generates the file to a terminal.
tftp address	Generates the file to TFTP. Type the TFTP server’s IP address or hostname.
self-signed-cert filename	Generates a self-signed SSL encryption certificate. The filename of the self-signed certificate to be generated must have the.p12 file extension.
exportable	(Optional) Allows the self-signed certificate to be exported.
rsa modulus	Specifies the size of the RSA modulus to be used when generating the self-signed certificate.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

The valid size (number of bits) for the RSA modulus for a self-signed certificate is dependent on the WAAS version:

For WAAS Version 6.1.x and earlier, the valid RSA module size is 512, 768, 1024, 1536, or 2048.

Note A self-signed certificate on WAAS Version 6.1.x or earlier with an RSA modulus size of 512 is not compatible with Mozilla FireFox Version 39 and later, or with Google Chrome Version 48 and later. A self-signed certificate on WAAS Version 6.1.x or earlier with an RSA modulus size of 512 is compatible with Internet Explorer 8 and later.

If you have previously configured the RSA modulus size as 512: to access the WAAS CM with Mozilla FireFox Version 39 and later, or with Google Chrome Version 48 and later, you must regenerate the self-signed certificate with an RSA modulus size of 2048, and then upgade to the specified version of Mozilla FireFox or Google Chrome.

For WAAS Version 6.2.x and later, the valid RSA module size is 768, 1024, 1536, or 2048. The RSA module size 512 is not used with WAAS Version 6.2.x and later.

Examples

The following example shows how to create an exportable self-signed certificate. The certificate file is named myfile.p12 and is created using a 2048-bit RSA modulus.

WAE# crypto generate self-signed-cert myfile.p12 exportable rsa modulus 2048

Generating a 2048bit RSA private key

..........++++++++++++

...++++++++++++

-----

You are about to be asked to enter information that will be incorporated

into your certificate request.

What you are about to enter is what is called a Distinguished Name or a DN.

There are quite a few fields but you can leave some blank

For some fields there will be a default value,

If you enter '.', the field will be left blank.

-----

Country Name (2 letter code) [US]:US

State or Province Name (full name) [California]:<cr> (Press Enter to accept the default.)

Locality Name (eg, city) [San Jose]:San Jose

Organization Name (eg, company) [Cisco Systems]:

Organizational Unit Name (eg, section) [ADBU]:

Common Name (eg, YOUR name) [www.cisco.com]:

Email Address [tac@cisco.com]:

WAE#

Related Commands

crypto delete

crypto import

To import SSL certificates and key files, use the crypto import EXEC command.

crypto import ca-certificate filename {disk pathname | ftp host | http host | scep url | sftp host | terminal | tftp host}

crypto import pkcs12 {filename | admin} [exportable] [ignore-cert-chain-order] pem-cert-key {disk pathname | ftp host | http host | scep url | sftp host | terminal | tftp host}

crypto import pcsk12 {filename | admin} [exportable] [ignore-cert-chain-order] pkcs12 {disk pathname | ftp host | http host | sftp host | terminal | tftp host}

Syntax Description

ca-certificate filename	Imports a certificate authority certificate file. The name of the CA certificate file to be imported (PEM format) must have.ca extension.
pkcs12 filename	Specifies a certificate intended for the management or an accelerated service (PKCS12 format). A PKCS12 file contains both the private encryption key and the public key certificate. The name of the PKCS12 file to be imported must have a.p12 extension. DSA-encoded certificates are not supported and will not be imported.
admin	Specifies that the certificate and key are for the Central Manager admin service. This option can be used only on the Central Manager.
exportable	(Optional) Configures the imported certificate to be exportable.
ignore-cert-chain- order	(Optional) Allows the crypto import command to import a certificate chain that does not have a strict order.
pem-cert-key	Imports both the certificate and key in PEM format. When you use the pem-cert-key keyword, you must specify the pathname and filename or the address and filename for both the certificate file and the key file for disk, ftp, sftp, and tftp.
pkcs12	Imports both the certificate and key in PKCS12 format.
disk pathname	Imports from a disk. Type the disk filename including the full path.
ftp address	Imports from FTP. Type the FTP server’s IP address or hostname.
sftp address	Imports from secure FTP. Type the secure FTP server’s IP address or hostname.
scep url	Imports from a SCEP server. Type the SCEP server’s IP address.
terminal	Imports from a terminal.
tftp address	Imports from TFTP. Type the TFTP server’s IP address or hostname.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The Central Manager admin service uses a self-signed certificate and key by default. You can use the crypto import pkcs12 admin command to import a custom certificate and key in PKCS12 or PEM format. If you delete the custom certificate and key, the self-signed certificate and key again become active.

Note DSA certificates and keys cannot be imported.

Examples

The following example shows how to import a CA certificate file named mycert.ca from a TFTP server:

WAE# crypto import ca-certificate mycert.ca tftp 00.00.00.00

Related Commands

crypto delete

crypto pki

To initialize the PKI managed store, use the crypto pki EXEC command.

crypto pki managed-store initialize

Syntax Description

managed-store	Specifies managed store commands.
initialize	Initializes the PKI managed store.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Examples

The following example shows how to initialize the PKI managed store:

WAE# crypto pki managed-store initialize

Related Commands

debug aaa accounting

To monitor and record AAA accounting debugging, use the debug aaa accounting EXEC command. To disable debugging, use the undebug form of this command.

debug aaa accounting

undebug aaa accounting

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Because the performance of the WAAS device degrades when you use the debug command, we recommend that you use this command only at the direction of Cisco TAC. For more information, see the “$paratext>” section.

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

The output associated with the debug command is written to either the syslog file in /local1/syslog.txt or the debug log associated with the module in the file /local1/errorlog/ module_name -errorlog.current.

The debug log file associated with a module will be rotated to a backup file when the current file reaches its maximum size. The backup files are named as follows: name -errorlog. #, where # is the backup file number.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable AAA accounting debug monitoring:

WAE# debug aaa accounting

Related Commands

debug aaa authorization

To monitor and record AAA authorization debugging, use the debug aaa authorization EXEC command. To disable debugging, use the undebug form of this command.

debug aaa authorization

undebug aaa authorization

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable AAA authorization debug monitoring:

WAE# debug aaa authorization

Related Commands

debug accelerator

To monitor and record accelerator debugging, use the debug accelerator EXEC command. To disable debugging, use the undebug form of this command.

debug accelerator generic [ connection | misc | shell | stats | all ]

no debug accelerator generic [ connection | misc | shell | stats | all ]

Syntax Description

generic	Enables generic accelerator debugging.


connection	Enables accelerator connection debugging.
misc	Enables generic accelerator miscellaneous debugging.
shell	Enables accelerator shell debugging.
stats	Enables generic accelerator statistics debugging.
all	Enables all accelerator debugging of a specified type.
http	Enables HTTP accelerator debugging.


bypass-list	Enables HTTP accelerator bypass list debugging.


cli	Enables configuration CLI debugging.
conditional-response	Enables HTTP accelerator metadata cache conditional response debugging.


dre-hints	Enables HTTP accelerator DRE hinting debugging.


metadatacache	Enables HTTP accelerator metadata cache debugging.


redirect-response	Enables HTTP accelerator metadata cache redirect response debugging.


subnet	Enables HTTP accelerator subnet configuration debugging.
supress-server-encoding	Enables HTTP accelerator supress-server-encoding debugging.


transaction	Enables HTTP accelerator transaction debugging.


unauthorized-response	Enables HTTP accelerator metadata cache unauthorized response debugging.


ica	Enables ICA accelerator debugging.
ao-connectionmgr	Enables ICA AO-ConnectionMgr debugging.
ao-parser	Enables ICA AO-Parser debugging.
cgp	Enables ICA CGP debugging.
connection	Enables ICA AO-Connection debugging.
crypto	Enables ICA CRYPTO debugging.
detectionparser	Enables ICA detectionparser debugging.
failure	Enables ICA allocation failure debugging.
hash	Enables ICA HASH debugging.
ica	Enables ICA parsing debugging.
initialization	Enables ICA initialization debugging.
io	Enables ICA IO debugging.
main	Enables ICA main debugging.
pipe	Enables ICA pipe debugging.
shell	Enables ICA shell debugging.
mapi	Enables MAPI accelerator debugging.


Common-flow	Enables MAPI common flow debugging.
DCERPC-layer	Enables MAPI DCERPC layer flow debugging.
EMSMDB-layer	Enables MAPI EMSMDB layer flow debugging.
IO	Enables MAPI IO flow debugging.
ROP-layer	Enables MAPI ROP layer flow debugging.
ROP-parser	Enables MAPI ROP parser flow debugging.
RCP-parser	Enables MAPI RCP parser flow debugging.
RPCHTTP-layer	Enable MAPI RPCHTTP-layer flow debugs
shell	Enables MAPI shell flow debugging.
Transport	Enables MAPI transport flow debugging.
Utilities	Enables MAPI utilities flow debugging.
smb	Enables SMB accelerator debugging.
cmd-close	Enables SMB close commands debugging.
cmd-create	Enables SMB create commands debugging.
cmd-lock	Enables SMB lock commands debugging.
cmd-others	Enables SMB other commands debugging.
cmd-query-info	Enables SMB query-info commands debugging.
cmd-read	Enables SMB read commands debugging.
cmd-set-info	Enables SMB set-info commands debugging.
cmd-write	Enables SMB write commands debugging.
flow	Enables SMB flow debugging.
large-data-flush	Enables SMB large data flush debugging.
lock-manager	Enables SMB lock manager debugging.
meta-data	Enables SMB meta data debugging.
named-pipe	Enables SMB named pipe debugging.
not-found-cache	Enables SMB not-found metadata cache debugging.
packeter	Enables SMB packeter debugging.
parser	Enables SMB parser debugging.
read-ahead	Enables SMB read-ahead debugging.
shell	Enables SMB shell debugging.
vfn	Enables SMB VFN debugging.
ssl	Enables SSL accelerator debugging.
accelerated-svc	Enables accelerated service debugging.
alarm	Enables SSL AO alarm debugging.
am	Enables SSL auth manager debugging.
am-generic-svc	Enables SSL am generic service debugging.
bio	Enables SSL bio layer debugging.
ca	Enables SSL cert auth module debugging.
ca-pool	Enables SSL cert auth pool debugging.
cipherlist	Enables SSL cipher list debugging.
client-to-server	Enables SSL client-to-server datapath debugging.
dataserver	Enables SSL dataserver debugging.
flow-shutdown	Enables SSL flow shutdown debugging.
ocsp	Enables SSL ocsp debugging.
oom-manager	Enables SSL oom-manager debugging.
openssl-internal	Enables SSL openssl internal debugging.
parser	Enables SSL accelerator parser debugging.
peering-svc	Enables SSL peering service debugging.
session-cache	Enables SSL session cache debugging.
shell	Enables SSL shell debugging.
sm-alert	Enables SSL session manager alert debugging.
sm-generic	Enables SSL session manager generic debugging.
sm-io	Enables SSL session manager i/o debugging.
sm-pipethrough	Enables SSL session manager pipethrough debugging.
synchronization	Enables SSL synchronization debugging.
verify	Enables SSL certificate verification debugging.
waas-to-waas	Enables SSL waas-to-waas datapath debugging.
client-ip ip-addr	Specifies the client IP address.
server-ip ip-addr	Specifies the server IP address.
wansecure	Enables WANSECURE debugging.
flow	Enables WANSECURE flow debugging.
mux	Enables WANSECURE mux debugging.
ocsp	Enables WANSECURE ocsp debugging.
shell	Enables WANSECURE shell debugging.
ssl	Enables WANSECURE ssl debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

The output associated with the debug accelerator name module command for an application accelerator is written to the file name ao-errorlog.current, where name is the accelerator name. The accelerator information manager debug output is written to the file aoim-errorlog.current.

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all accelerator debug monitoring:

WAE# debug accelerator all

Related Commands

debug accelerator object-cache-ipc

debug accelerator http object-cache

To enable object-cache debugging, use the debug accelerator http object-cache EXEC command.

debug accelerator http object-cache {all | configuration | gate-keeper | logger | preposition | response-headers | statistics | traffic-plugin}

Syntax Description

all	Enable all object-cache debugging.
configuration	Enable configuration debugging.
gate-keeper	Enable gate keeper debugging.
logger	Enable logger debugging.
preposition	Enable cache prepositioning debugging.
response-headers	Enable debugging headers in HTTP response.
statistics	Enable statistics debugging.
traffic-plugin	Enable traffic plugin debugging.

Command Default

No default behavior or values.

Command Modes

EXEC

Device Modes Default

application-accelerator

Usage Guidelines

Use the debug accelerator http object-cache EXEC command to enable debugging for all object-cache debugging, or to specifying debugging for a particular object-cache area, such as configuration, cache preposition, or statistics.

Examples

The following example shows how to enable debugging for all parameters for the HTTP object cache:

WAE# debug accelerator http object-cache all

debug accelerator mapi rpchttp-layer

To enable debugging of the MAPI RPC HTTP accelerator, use the debug accelerator mapi rpchttp EXEC command. To disable debugging, use the no form of this command.

debug accelerator mapi rpchttp-layer

no debug accelerator mapi rpchttp -layer

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug accelerator mapi rpchttp-layer EXEC command to enable debugging of the mapi RPC HTTP application accelerator.

Examples

The following example shows how to enable debugging for the MAPI object cache i/o:

WAE# debug accelerator mapi rpchttp-layer

Related Commands

debug accelerator

debug accelerator object-cache-io

To enable debugging of a specified accelerator object cache i/o debugging, use the debug accelerator object-cache-io enable EXEC command. To disable debugging, use the no form of this command.

debug accelerator ao-name object-cache-io

no debug accelerator ao-name object-cache-io

Syntax Description

ao-name

The name of the application accelerator specified for i/o debugging: SMB or HTTP.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug accelerator object-cache-io EXEC command to enable debugging for object cache i/o data for a specified application accelerator.

Examples

The following example shows how to enable debugging for the MAPI object cache i/o:

WAE# debug accelerator smb object-cache-io

Related Commands

debug accelerator object-cache-mgr

debug accelerator object-cache-io

debug accelerator object-cache-ipc

To enable debugging of IPC transport data for a specified accelerator object cache, use the debug accelerator object-cache-ipc enable EXEC command. To disable debugging, use the no form of this command.

debug accelerator ao-name object-cache-ipc

no debug accelerator ao-name object-cache-ipc

Syntax Description

ao-name

The name of the application accelerator specified for ipc message debugging: SMB or HTTP.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug accelerator object-cache-ipc EXEC command to enable debugging for object cache IPC transport data for a specified application accelerator.

Examples

The following example shows how to enable debugging for IPC transport data for the MAPI object cache.

WAE# debug accelerator smb object-cache-ipc

Related Commands

debug accelerator object-cache-mgr

debug accelerator object-cache-io

debug accelerator object-cache-mgr

To enable debugging of of the object cache storage manager for a specified accelerator object cache, use the debug accelerator object-cache-mgr enable EXEC command. To disable debugging, use the no form of this command.

debug accelerator ao-name object-cache-mgr

no debug accelerator ao-name object-cache-mgr

Syntax Description

ao-name

The name of the application accelerator specified for object cache storage manager debugging: SMB or HTTP.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug accelerator object-cache-mgr EXEC command to enable debugging for the object cache storage manager for a specified application accelerator.

Examples

The following example shows how to enable debugging for the object cache storage manager for the MAPI application accelerator.

WAE# debug accelerator smb object-cache-mgr

Related Commands

debug accelerator object-cache-ipc

debug all

To monitor and record all debugging, use the debug all EXEC command. To disable debugging, use the undebug form of this command.

debug all

undebug all

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all debug monitoring:

WAE# debug all

Related Commands

debug authentication

To monitor and record authentication debugging, use the debug authentication EXEC command. To disable debugging, use the undebug form of this command.

debug authentication { user | windows-domain }

undebug authentication { user | windows-domain }

Syntax Description

user	Enables debugging of the user login against the system authentication.
windows-domain	Enables Windows domain authentication debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable user authentication debug monitoring, verify that it is enabled, and then disable debug monitoring:

WAE# debug authentication user

WAE# show debugging

Debug authentication (user) is ON

WAE# no debug authentication user

Related Commands

debug auto-discovery

To trace connections in the auto discovery module, use the debug auto-discovery EXEC command. To disable debugging, use the undebug form of this command.

debug auto-discoveryconnection

undebug auto-discovery connection

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable auto discovery connection debugging:

WAE# debug auto-discovery connection

Related Commands

debug buf

To monitor and record buffer manager debugging, use the debug buf EXEC command. To disable debugging, use the undebug form of this command.

debug buf { all | dmbuf | dmsg }

undebug buf { all | dmbuf | dmsg }

Syntax Description

all	Enables all buffer manager debugging.
dmbuf	Enables only dmbuf debugging.
dmsg	Enables only dmsg debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all buffer manager debug monitoring:

WAE# debug buff all

Related Commands

debug cdp

To monitor and record CDP debugging, use the debug cdp EXEC command. To disable debugging, use the undebug form of this command.

debug cdp { adjacency | events | ip | packets }

undebug cdp { adjacency | events | ip | packets }

Syntax Description

adjacency	Enables CDP neighbor information debugging.
events	Enables CDP events debugging.
ip	Enables CDP IP debugging.
packets	Enables packet-related CDP debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable CDP events debug monitoring:

WAE# debug cdp events

Related Commands

debug cli

To monitor and record CLI debugging, use the debug cli EXEC command. To disable debugging, use the undebug form of this command.

debug cli { all | bin | parser }

undebug cli { all | bin | parser }

Syntax Description

all	Enables all CLI debugging.
bin	Enables CLI command binary program debugging.
parser	Enables CLI command parser debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all CLI debug monitoring:

WAE# debug cli all

Related Commands

debug cmm

To monitor and record cluster membership manager debugging, use the debug cmm EXEC command. To disable debugging, use the undebug form of this command.

debug cmm { all | cli | events | ipc | misc | packets | shell | timers }

undebug cmm { all | cli | events | ipc | misc | packets | shell | timers }

Syntax Description

all	Enables all cluster membership manager (CMM) debugging.
cli	Enables CMM CLI debugging.
events	Enables CMM state machine event debugging.
ipc	Enables CMM ipc message debugging.
misc	Enables CMM miscellaneous debugging.
packets	Enables CMM packet debugging.
shell	Enables CMM infra debugging.
timers	Enables CMM state machine timer debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all cmm debug monitoring:

WAE# debug cmm all

Related Commands

debug cms

To monitor and record CMS debugging, use the debug cms EXEC command. To disable debugging, use the undebug form of this command.

debug cms{router-config | stats}

undebug cms

Syntax Description

router-config	Enables debug only router configuration from CM
stats	Enables debug only statistics

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable CMS debug monitoring:

WAE# debug cms

Related Commands

debug connection

To enable connection-specific debugging, use the debug connection EXEC command. To disable debugging, use the undebug form of this command.

debug connection { all | access-list acl-name }

undebug connection { all | access-list acl-name }

Syntax Description

all	Enables all connection-specific debugging.
access-list acl-name	Enables access list connection debugging. Access list name is an alphanumeric identifier up to 30 characters, beginning with a letter.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all connection-specific debug monitoring:

WAE# debug connection all

Related Commands

debug dataserver

To monitor and record data server debugging, use the debug dataserver EXEC command. To disable debugging, use the undebug form of this command.

debug dataserver { all | clientlib | server }

undebug dataserver { all | clientlib | server }

Syntax Description

all	Enables all data server debugging.
clientlib	Enables data server client library module debugging.
server	Enables data server module debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all data server debug monitoring:

WAE# debug dataserver all

Related Commands

debug dhcp

To monitor and record DHCP debugging, use the debug dhcp EXEC command. To disable debugging, use the undebug form of this command.

debug dhcp

undebug dhcp

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable DHCP debug monitoring:

WAE# debug dhcp

Related Commands

debug dre

To monitor and record DRE debugging, use the debug dre EXEC command. To disable debugging, use the undebug form of this command.

debug dre { aggregation | all | cache | chunking | connection { aggregation [ acl ] | cache [ acl ] | chunking [ acl ] | core [ acl ] | message [ acl ] | misc [ acl ] | acl } | core | lz | message | misc | nack | packet }

undebug dre { aggregation | all | cache | chunking | connection { aggregation [ acl ] | cache [ acl ] | chunking [ acl ] | core [ acl ] | message [ acl ] | misc [ acl ] | acl } | core | lz | message | misc | nack | packet }

Syntax Description

aggregation	Enables DRE chunk-aggregation debugging.
all	Enables the debugging of all DRE commands.
cache	Enables DRE cache debugging.
chunking	Enables DRE chunking debugging.
connection	Enables DRE connection debugging.
acl	ACL to limit connections traced.
core	Enables DRE core debugging.
lz	Enables DRE lz debugging.
message	Enables DRE message debugging for a specified connection.
misc	Enables DRE other debugging for a specified connection.
nack	Enables DRE NACK debugging.
packet	Enables DRE packet debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all DRE debug monitoring:

WAE# debug dre all

Related Commands

debug egress-method

To monitor and record egress method debugging, use the debug egress-method EXEC command. To disable debugging, use the undebug form of this command.

debug egress-method connection

undebug egress-method connection

Syntax Description

connection

(Optional) Enables egress method connection debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all egress method debug monitoring:

WAE# debug egress-method connection

Related Commands

debug encryption-service

To monitor and record encryption service debugging, use the debug encryption-service EXEC command. To disable debugging, use the undebug form of this command.

debug encryption-service { all | application-layer | cfgmgr | dcerpc-layer | gss | io | secure-store | server | shell | transport-lib | utilities }

undebug encryption-service { all | application-layer | cfgmgr | dcerpc-layer | gss | io | secure-store | server | shell | transport-lib | utilities }

Syntax Description

all	Enables debugging of all encryption services components.
application-layer	Enables debugging of the encryption services application layer.
cfgmgr	Enables debugging of the encryption services configuration manager.
dcerpc-layer	Enables debugging of the encryption services dcerpc layer.
gss	Enables debugging of the encryption services gss.
io	Enables debugging of the encryption services io.
secure-store	Enables debugging of the encryption services secure store.
server	Enables debugging of the encryption services server.
shell	Enables debugging of the encryption services shell.
transport-lib	Enables debugging of the encryption services transport library.
utilities	Enables debugging of the encryption services utilities.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable debugging of all encryption services components:

WAE# debug encryption-services all

Related Commands

debug fda

To monitor and record flow distribution agent debugging, use the debug fda EXEC command. To disable debugging, use the undebug form of this command.

debug fda { all | events | infra | messages }

undebug fda { all | events | infra | messages }

Syntax Description

all	Enables all flow distribution agent debugging.
events	Enables only flow distribution agent event debugging.
infra	Enables only flow distribution agent infra debugging.
messages	Enables only flow distribution agent message debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all flow distribution agent debug monitoring:

WAE# debug fda all

Related Commands

debug fdm

To monitor and record flow distribution manager debugging, use the debug fdm EXEC command. To disable debugging, use the undebug form of this command.

debug fdm { all | events | infra | messages }

undebug fdm { all | events | infra | messages }

Syntax Description

all	Enables all flow distribution manager debugging.
events	Enables only flow distribution manager event debugging.
infra	Enables only flow distribution manager infra debugging.
messages	Enables only flow distribution manager message debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all flow distribution manager debug monitoring:

WAE# debug fdm all

Related Commands

debug filtering

To trace filtering connections setup, use the debug filtering EXEC command. To disable debugging, use the undebug form of this command.

debug filtering connection

undebug filtering connection

Syntax Description

connection

(Optional) Enables filtering module connection debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable filtering module connection debugging:

WAE# debug filtering connection

Related Commands

debug flow

To monitor and record network traffic flow debugging, use the debug flow EXEC command. To disable debugging, use the undebug form of this command.

debug flow monitor type performance-monitor tcpstat-v1

undebug flow monitor type performance-monitor tcpstat-v1

Syntax Description

monitor	Enables monitor flow performance debugging commands.
tcpstat-v1	Enables tcpstat-v1 debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable network traffic flow debug monitoring:

WAE# debug flow monitor type performance-monitor tcpstat-v1

Related Commands

debug generic-gre

To monitor and record generic GRE egress method debugging, use the debug generic-gre EXEC command. To disable debugging, use the undebug form of this command.

debug generic-gre

undebug generic-gre

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable generic GRE egress method debug monitoring:

WAE# debug generic-gre

Related Commands

debug hw-raid

To monitor and record hardware RAID debugging, use the debug hw-raid EXEC command. To disable debugging, use the undebug form of this command.

debug hw-raid { all | cli | daemon }

undebug hw-raid { all | cli | daemon }

Syntax Description

all	Enables all hardware RAID debug commands.
cli	Enables hardware RAID CLI debugging.
daemon	Enables hardware RAID daemon debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all hardware RAID debug monitoring:

WAE# debug hw-raid all

Related Commands

debug imd

To monitor and record interface manager debugging, use the debug imd EXEC command. To disable debugging, use the undebug form of this command.

debug imd { all | cli | infra | nprm | stats }

undebug fdm { all | cli | infra | nprm | stats }

Syntax Description

all	Enables all interface manager debugging.
cli	Enables only interface manager cli debugging.
infra	Enables only interface manager infra debugging.
nprm	Enables only interface manager nprm debugging.
stats	Enables only interface manager stats debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all interface manager debug monitoring:

WAE# debug imd all

Related Commands

debug inline

To enable inline module debugging, use the debug inline EXEC command. To disable debugging, use the undebug form of this command.

debug inline { debug | info | warn }

undebug inline { debug | info | warn }

Syntax Description

debug	Sets the debug level to debug.
info	Sets the debug level to info.
warn	Sets the debug level to warn.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to set the log level for inline modules to warning level:

WAE# debug inline warn

Related Commands

debug key-manager

To monitor and record key manager debugging, use the debug key-manager EXEC command. To disable debugging, use the undebug form of this command.

debug key-manager

undebug key-manager

Syntax Description

key-manager

(Optional) Enables key manager debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

central-manager (primary only)

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable monitoring API debug monitoring:

WAE# debug key-manager

Related Commands

debug logging

To monitor and record logging debugging, use the debug logging EXEC command. To disable debugging, use the undebug form of this command.

debug logging all

undebug logging all

Syntax Description

all

Enables all logging debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all logging debug monitoring:

WAE# debug logging all

Related Commands

debug monapi

To monitor and record monitor API debugging, use the debug monapi EXEC command. To disable debugging, use the undebug form of this command.

debug monapi

undebug monapi

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

central-manager (primary only)

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable monitoring API debug monitoring:

WAE# debug monapi

Related Commands

debug nplogd

To monitor and record NP log daemon debugging, use the debug nplogd EXEC command. To disable debugging, use the undebug form of this command.

debug nplogd all

undebug nplogd all

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable NP log daemon debug monitoring:

WAE# debug nplogd all

Related Commands

debug ntp

To monitor and record NTP debugging, use the debug ntp EXEC command. To disable debugging, use the undebug form of this command.

debug ntp

undebug ntp

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable NTP debug monitoring:

WAE# debug ntp

Related Commands

debug object-cache database

To enable debugging of the object cache database, use the debug object-cache database EXEC command. To disable debugging, use the no form of this command.

debug object-cache database

no debug object-cache database

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug object-cache database EXEC command to enable debugging for the object cache database.

Examples

The following example shows how to enable debugging for the object cache database.

WAE# debug object-cache database

Related Commands

debug object-cache existence-cache

To enable debugging of the object cache existence cache database, use the debug object-cache existence-cache database EXEC command. To disable debugging, use the no form of this command.

debug object-cache existence-cache

no debug object-cache existence-cache

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug object-cache existence-cache EXEC command to enable debugging for the existence cache, which maintains information on whether or not an object is present in the object databases.

Examples

The following example shows how to enable debugging for the object cache existence cache.

WAE# debug object-cache existence-cache

Related Commands

debug object-cache garbage-collection

To enable debugging of the object cache garbage collection function, use the debug object-cache garbage-collection EXEC command. To disable debugging, use the no form of this command.

debug object-cache garbage-collection

no debug object-cache garbage-collection

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug object-cache garbage-collection EXEC command to enable debugging of the object cache garbage collection function, which collects objects that are either invalid or rarely used.

Examples

The following example shows how to enable debugging for the object cache garbage collection function.

WAE# debug object-cache garbage-collection

Related Commands

debug accelerator object-cache-ipc

debug object-cache ipc

To enable debugging of object cache IPC transport data, use the debug object-cache ipc enable EXEC command. To disable debugging, use the no form of this command.

debug object-cache ipc

no debug object-cache ipc

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug object-cache ipc EXEC command to enable debugging of object cache IPC transport data.

Examples

The following example shows how to enable debugging for object cache IPC transport data.

WAE# debug object-cache ipc

Related Commands

To enable debugging of the object cache load monitor function, use the debug object-cache load-monitor enable EXEC command. To disable debugging, use the no form of this command.

debug object-cache load-monitor

no debug object-cache load-monitor

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

Use the debug object-cache load-monitor EXEC command to enable debugging of the object cache load monitor function, which monitors disk load and usage.

Examples

The following example shows how to enable debugging for the object cache load monitor function.

WAE# debug object-cache load-monitor

Related Commands

debug rbcp

To monitor and record RBCP debugging, use the debug rbcp EXEC command. To disable debugging, use the undebug form of this command.

debug rbcp

undebug rbcp

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable RBCP debug monitoring:

WAE# debug rbcp

Related Commands

debug rmd

To monitor and record route manager debugging, use the debug rmd EXEC command. To disable debugging, use the undebug form of this command.

debug rmd { all | cli | infra | nprm }

undebug rmd { all | cli | infra | nprm }

Syntax Description

all	Enables all route manager debugging.
cli	Enables only route manager cli debugging.
infra	Enables only route manager infra debugging.
nprm	Enables only route manager nprm debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all route manager debug monitoring:

WAE# debug rmd all

Related Commands

debug rpc

To monitor and record remote procedure calls (RPC) debugging, use the debug rpc EXEC command. To disable debugging, use the undebug form of this command.

debug rpc { detail | trace }

undebug rpc { detail | trace }

Syntax Description

detail	Displays RPC logs of priority detail or higher.
trace	Displays RPC logs of priority trace or higher.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable RPC detail debug monitoring:

WAE# debug rpd detail

Related Commands

debug service-insertion

To trace connections in the service-insertion module, use the debug service-insertion EXEC command. To disable debugging, use the undebug form of this command.

debug service-insertion connection

undebug service-insertion connection

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all service-insertion module debug monitoring:

WAE# debug service-insertion connection

Related Commands

debug service-policy

To monitor and record service policy debugging, use the debug service-policy EXEC command. To disable debugging, use the undebug form of this command.

debug service-policy type { waas }

undebug service-policy type waas }

Syntax Description

waas

Enables WAAS service policy debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable WAAS service policy debug monitoring:

WAE# debug service-policy waas

Related Commands

debug snmp

To monitor and record SNMP debugging, use the debug snmp EXEC command. To disable debugging, use the undebug form of this command.

debug snmp { all | cli | main | mib | traps }

undebug snmp { all | cli | main | mib | traps }

Syntax Description

all	Enables all SNMP debug commands.
cli	Enables SNMP CLI debugging.
main	Enables SNMP main debugging.
mib	Enables SNMP MIB debugging.
traps	Enables SNMP trap debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all SNMP debug monitoring:

WAE# debug snmp all

Related Commands

debug standby

To enable standby debugging, use the debug standby EXEC command. To disable debugging, use the undebug form of this command.

debug standby [all]

undebug standby [all]

Syntax Description

all

(Optional) Enables standby debugging using all debug features.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all standby debug monitoring:

WAE# debug standby all

Related Commands

debug statistics

To monitor and record statistics debugging, use the debug statistics EXEC command. To disable debugging, use the undebug form of this command.

debug statistics { all | ao | client | collector | ipc | messages | serializer | sqm }

undebug statistics { all | ao | client | collector | ipc | messages | serializer | sqm }

Syntax Description

all	Enables all statistics debug commands.
ao	Enables statistics acceleration debugging.
client	Enables statistics client debugging.
collector	Enables statistics collector debugging.
ipc	Enables statistics IPC debugging.
messages	Enables statistics messages/buffers debugging.
serializer	Enables statistics serializer debugging.
sqm	Enables statistics computation debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

services-controller

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all statistics debug monitoring:

WAE# debug statistics all

Related Commands

debug tfo

To monitor and record TFO flow optimization debugging, use the debug tfo EXEC command. To disable debugging, use the undebug form of this command.

debug tfo {all | buffer-mgr | dre-flow | netio | scheduler }

undebug tfo {all | buffer-mgr | dre-flow | netio | scheduler }

Syntax Description

all	Enables all TFO debugging.
buffer-mgr	Enables TFO data-buffer from buffer manager debugging.
dre-flow	Enables TFO DRE flow debugging for all connections.
netio	Enables TFO connection debugging for the network input/output module.
scheduler	Enables TFO scheduler debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable all TFO flow optimization debug monitoring:

WAE# debug tfo all

Related Commands

debug translog

To monitor and record transaction logging debugging, use the debug translog EXEC command. To disable debugging, use the undebug form of this command.

debug translog { detail | export | info }

undebug translog { detail | export | info }

Syntax Description

detail	Enables transaction log detailed debugging.
export	Enables transaction log FTP export debugging.
info	Enables transaction log high level debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable transaction logging detail debug monitoring:

WAE# debug translog detail

Related Commands

debug wafs

To set the log level of the WAFS Device Manager component, use the debug wafs EXEC command. To disable debugging, use the undebug form of this command.

debug wafs manager { debug | error | info | warn }

undebug wafs manager { debug | error | info | warn }

Syntax Description

manager	Sets the logging level for the Device Manager.
debug	Specifies debug.
error	Specifies error.
info	Specifies info.
warn	Specifies warn.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to set the log level for all WAFS components to error level:

WAE# debug wafs manager error

Related Commands

debug wccp

To monitor and record WCCP information debugging, use the debug wccp EXEC command. To disable debugging, use the undebug form of this command.

debug wccp { all | detail | error | events | packets }

undebug wccp { all | detail | error | events | packets }

Syntax Description

all	Enables all WCCP debugging functions.
detail	Enables the WCCP detail debugging.
error	Enables the WCCP error debugging.
events	Enables the WCCP events debugging.
packets	Enables the WCCP packet-related information debugging.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

Usage Guidelines

If the watchdog utility is not running, the message “WAAS is not running” appears.

Use the show debugging command to display enabled debug options.

For any debug command, system logging must be enabled. The command to enable logging is the logging disk enable global configuration command, which is enabled by default.

If a debug command module uses the syslog for debug output, then you must use the logging disk priority debug global configuration command (the default is logging disk priority notice).

If a debug command module uses the debug log for output, then the output can be filtered based on the priority level configuration for the four different levels of debug log output, as follows:

For filtering on critical debug messages only, use the logging disk priority critical g lobal configuration command.
For filtering on critical and error level debug messages, use the logging disk priority error global configuration command.
For filtering on critical, error, and trace debug level debug messages, use the logging disk priority debug global configuration command.
For seeing all debug log messages, which include critical, error, trace and detail messages, use the logging disk priority detail global configuration command.

Regardless of the priority level configuration, any syslog messages at the LOG_ERROR or higher priority will be automatically written to the debug log associated with a module.

We recommend that you use the debug and undebug commands only at the direction of Cisco Systems technical support personnel.

Examples

The following example shows how to enable WCCP information debug monitoring:

WAE# debug wccp all

Related Commands

(config) disk object-cache extend

delfile

To delete a file from the current directory, use the delfile EXEC command.

delfile filename

Syntax Description

filename

Name of the file to delete.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the delfile EXEC command to remove a file from a SYSFS partition on the disk drive of the WAAS device.

Examples

The following example shows how to delete a temporary file from the /local1 directory using an absolute path:

WAE# delfile /local1/tempfile

Related Commands

cpfile

dir

lls

mkdir

pwd

rename

deltree

To remove a directory with all of its subdirectories and files, use the deltree EXEC command.

deltree directory

Syntax Description

directory

Name of the directory tree to delete.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the deltree EXEC command to remove a directory and all files within the directory from the WAAS SYSFS file system. No warning is given that you are removing the subdirectories and files.

Note Make sure that you do not remove files or directories required for the WAAS device to function properly.

Examples

The following example shows how to delete the testdir directory from the /local1 directory:

WAE# deltree /local1/testdir

Related Commands

cpfile

dir

lls

mkdir

pwd

rename

dir

To view details of one file or all files in a directory, use the dir EXEC command.

dir [ directory ]

Syntax Description

directory

(Optional) Name of the directory to list.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the dir EXEC command to view a detailed list of files contained within the working directory, including information about the file name, size, and time created. The lls EXEC command produces the same output.

Examples

The following example shows how to create a detailed list of all the files for the current directory:

WAE# dir

size time of last change name

------------- ------------------------- -----------

4096 Fri Feb 24 14:40:00 2006 <DIR> actona

4096 Tue Mar 28 14:42:44 2006 <DIR> core_dir

4096 Wed Apr 12 20:23:10 2006 <DIR> crash

4506 Tue Apr 11 13:52:45 2006 dbupgrade.log

4096 Tue Apr 4 22:50:11 2006 <DIR> downgrade

4096 Sun Apr 16 09:01:56 2006 <DIR> errorlog

4096 Wed Apr 12 20:23:41 2006 <DIR> logs

16384 Thu Feb 16 12:25:29 2006 <DIR> lost+found

4096 Wed Apr 12 03:26:02 2006 <DIR> sa

24576 Sun Apr 16 23:38:21 2006 <DIR> service_logs

4096 Thu Feb 16 12:26:09 2006 <DIR> spool

9945390 Sun Apr 16 23:38:20 2006 syslog.txt

10026298 Thu Apr 6 12:25:00 2006 syslog.txt.1

10013564 Thu Apr 6 12:25:00 2006 syslog.txt.2

10055850 Thu Apr 6 12:25:00 2006 syslog.txt.3

10049181 Thu Apr 6 12:25:00 2006 syslog.txt.4

4096 Thu Feb 16 12:29:30 2006 <DIR> var

508 Sat Feb 25 13:18:35 2006 wdd.sh.signed

The following example shows how to display the detailed information for only the logs directory:

WAE# dir logs

size time of last change name

------------- ------------------------- -----------

4096 Thu Apr 6 12:13:50 2006 <DIR> actona

4096 Mon Mar 6 14:14:41 2006 <DIR> apache

4096 Sun Apr 16 23:36:40 2006 <DIR> emdb

4096 Thu Feb 16 11:51:51 2006 <DIR> export

92 Wed Apr 12 20:23:20 2006 ftp_export.status

4096 Wed Apr 12 20:23:43 2006 <DIR> rpc_httpd

0 Wed Apr 12 20:23:41 2006 snmpd.log

4096 Sun Mar 19 18:47:29 2006 <DIR> tfo

Related Commands

lls

disable

To turn off privileged EXEC commands, use the disable EXEC command.

disable

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels, user and privileged. To access privileged-level EXEC mode, enter the enable EXEC command at the user access level prompt and specify the admin password when prompted for a password.

WAE> enable

Password:

The disable command places you in the user-level EXEC shell (notice the prompt change).

Examples

The following example shows how to enter the user-level EXEC mode from the privileged EXEC mode:

WAE# disable

WAE>

Related Commands

enable

disk

To configure disks on a WAAS device, use the disk EXEC command.

disk delete-partitions diskname

disk delete-data-partitions

disk delete-preserve-software

disk disk-name diskxx enable force

disk disk-name disk xx replace

disk insert diskname

disk recreate-raid

disk scan-errors diskname

Syntax Description

delete-partitions diskname	Deletes data on the specified logical disk drive. After using this command, the WAAS software treats the specified disk drive as blank. All previous data on the drive is inaccessible. Specify the name of the disk from which to delete partitions (disk00, disk01). For RAID-5 systems, this option is not available because only one logical drive is available.
delete-data-partitions	Deletes all data partitions on all logical drives. Data partitions include the CONTENT, PRINTSPOOL, and GUEST partitions. These partitions include all DRE cache files and print spool files.
delete-preserve-software	Deletes all disk and data partitions and preserves current software version and CM registration details.
disk-name diskxx enable force	Reenables a defunct drive (with or without removing it) that has been previously shut down. Note This option is available only on RAID-5 systems.
disk-name disk xx replace	Shuts down the physical disk with the name disk xx (disk00, disk01, etc.) so that it can be replaced in the RAID-5 array. Note This option is available only on RAID-5 systems.
insert diskname	Instructs the SCSI host to rescan the bus to detect and mount the newly inserted disk. Specify the name of the disk to be inserted (disk00, disk01). Note This option is available only on WAE-612 models.
recreate-raid	Recreates the RAID-5 array. Note This option is available only on RAID-5 systems.
scan-errors diskname	Scans SCSI or IDE disks for errors and remaps the bad sectors if they are unused. Specify the name of the disk to be scanned (disk00, disk01). For RAID-5 systems, this command scans the logical RAID device for errors. On these systems, there is no diskname option.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The WAAS software supports hot-swap functionality for both failed disk replacement and scheduled disk maintenance. On the WAE-612, use the disk disk-name diskxx shutdown global configuration command to shut down a disk for scheduled disk maintenance. (For the scheduled disk maintenance procedure, see the chapter “Maintaining Your WAAS System” in the Cisco Wide Area Application Services Configuration Guide.)

The disk hot-swap functionality automatically disables a failed disk if the system detects one critical disk alarm. The software removes the failed disk automatically regardless of the setting for disk error-handling.

For WAE-612 models, when you replace a failed disk that was automatically disabled by the software, use the disk insert EXEC command to bring the disk back into service. For all other models, see the (config) disk disk-name command section.

To identify which disks have been identified as failed or bad, use the show disks failed-disk-id EXEC command. Do not reinsert any disk with a serial number shown in this list.

Use the disk delete-partitions EXEC command to remove all disk partitions on a single disk drive on a WAAS device or to remove the disk partition on the logical drive for RAID-5 systems.

Caution

Be careful when using the disk delete-partitions EXEC command because the WAAS software treats the specified disk drive as blank. All previous data on the drive will become inaccessible.

The disk delete-data-partitions command deletes the DRE caches.

After using the disk delete-data-partitions command, you must reload the device. The data partitions are automatically re-created and the caches are initialized, which can take several minutes. DRE optimization is not done until the DRE cache has finished initializing. The show statistics dre EXEC command reports “TFO: Initializing disk cache” until then. It is best not to interrupt DRE cache initialization by reloading the device again until after cache initialization has finished. However, if DRE cache initialization is interrupted, on the next reboot the disk is checked, which takes extra time, and DRE initialization is completed again.

When you upgrade to software version 6.1.1, and execute disk-delete-preserve-software command for the first time, all data and system partitions are re-created.
Use the disk delete-preserve-software command if you want to delete all existing data and system partitions, and yet want to preserve the software version and the device registration details with the Central Manager. This changes the software store partition size from 1 GB to 2GB. This command is applicable for all vWAAS devices, ISR WAAS devices and SM-SRE devices.

Examples

The following example shows how to recreate the RAID-5 array:

WAE# disk recreate-raid

Related Commands

(config) disk disk-name

(config) disk error-handling

show disks

dnslookup

To resolve a host or domain name to an IP address(IPv4/IPv6), use the dnslookup EXEC command.

dnslookup { hostname | domainname| IPv4/IPv6 address }

Syntax Description

hostname	Name of DNS server on the network.
domainname	Name of domain.
ip-address	IPv4 or IPv6 address

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how the dnslookup command is used to resolve the hostname myhost to IP address172.31.69.11

WAE# dnslookup myhost

official hostname: myhost.abc.com

address: 172.31.69.11

The following example shows how the dnslookup command is used to resolve the hostname abd.com to IP address 192.168.219.25:

WAE# dnslookup abc.com

official hostname: abc.com

address: 192.168.219.25

The following example shows how the dnslookup command is used to resolve an IP address used as a hostname to 10.0.11.0:

WAE# dnslookup 10.0.11.0

official hostname: 10.0.11.0

address: 10.0.11.0

The following example shows how the dnslookup command is used to resolve an IP address to a hostname:

WAE# dnslookup 2012:3:3:3::8

official hostname: CM.cisco.com

address:2012:3:3:3::8

enable

To access privileged EXEC commands, use the enable EXEC command.

enable

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the WAAS software CLI EXEC mode for setting, viewing, and testing system operations. This command mode is divided into two access levels: user and privileged. To access privileged-level EXEC mode, enter the enable EXEC command at the user access level prompt and specify the admin password when prompted for a password.

If using TACACS+ authentication, there is an enable password feature in TACACS+ that allows an administrator to define a different enable password for each user. If a TACACS+ user enters the enable EXEC command to access privileged EXEC mode, that user must enter the admin password defined by the TACACS+ server.

The disable command takes you from privileged EXEC mode to user EXEC mode.

Examples

The following example shows how to access privileged EXEC mode:

WAE> enable

WAE#

Related Commands

disable

exit

exit

To terminate privileged-level EXEC mode and return to the user-level EXEC mode, use the exit command.

exit

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

All modes

Device Modes

application-accelerator

central-manager

Usage Guidelines

The exit EXEC command is equivalent to pressing Ctrl-Z or entering the end command. Entering the exit command in the user level EXEC shell terminates the console or Telnet session.

Examples

The following example shows how to terminate privileged-level EXEC mode and return to the user-level EXEC mode:

WAE# exit

WAE>

Related Commands

(config) exit

find-pattern

To search for a particular pattern in a file, use the find-pattern command in EXEC mode.

find-pattern {binary reg-express filename | count reg-express filename | lineno reg-express filename | match reg-express filename | nomatch reg-express filename | recursive reg-express filename }

find-pattern case { binary reg-express filename | count reg-express filename | lineno reg-express filename | match reg-express filename | nomatch reg-express filename | recursive reg-express filename }

Syntax Description

binary reg-express filename	Does not suppress the binary output. Specifies the regular expression to be matched and the filename.
count reg-express filename	Prints the number of matching lines. Specifies the regular expression to be matched and the filename.
lineno reg-express filename	Prints the line number with output. Specifies the regular expression to be matched and the filename.
match reg-express filename	Prints the matching lines. Specifies the regular expression to be matched and the filename.
nomatch reg-express filename	Prints the nonmatching lines. Specifies the regular expression to be matched and the filename.
recursive reg-express filename	Searches a directory recursively. Specifies the regular expression to be matched and the filename.
case	Matches a case-sensitive pattern.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to search a file recursively for a case-sensitive pattern:

WAE# find-pattern case recursive admin removed_core

-rw------- 1 admin root 95600640 Oct 12 10:27 /local/local1/core_dir/

core.3.0.0.b5.eh.2796

-rw------- 1 admin root 97054720 Jan 11 11:31 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.14086

-rw------- 1 admin root 96845824 Jan 11 11:32 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.14823

-rw------- 1 admin root 101580800 Jan 11 12:01 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.15134

-rw------- 1 admin root 96759808 Jan 11 12:59 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.20016

-rw------- 1 admin root 97124352 Jan 11 13:26 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.8095

The following example shows how to search a file for a pattern and print the matching lines:

WAE# find-pattern match 10 removed_core

Tue Oct 12 10:30:03 UTC 2004

-rw------- 1 admin root 95600640 Oct 12 10:27 /local/local1/core_dir/

core.3.0.0.b5.eh.2796

-rw------- 1 admin root 101580800 Jan 11 12:01 /local/local1/core_dir/

core.cache.3.0.0.b131.cnbuild.15134

The following example shows how to search a file for a pattern and print the number of matching lines:

WAE# find-pattern count 10 removed_core

Related Commands

dir

lls

help

To obtain online help for the command-line interface, use the help EXEC command.

help

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC and global configuration

Device Modes

application-accelerator

central-manager

Usage Guidelines

You can obtain help at any point in a command by entering a question mark (?). If nothing matches, the help list will be empty, and you must back up until entering a ? shows the available options.

Two styles of help are provided:

Full help is available when you are ready to enter a command argument (for example, show ?) and describes each possible argument.
Partial help is provided when you enter an abbreviated command and you want to know what arguments match the input (for example, show stat?).

Examples

The following example shows how to display the output of the help EXEC command:

WAE# help

Help may be requested at any point in a command by entering a question mark '?'. If nothing matches, the help list will be empty and you must backup until entering a '?' shows the available options.

Two styles of help are provided:

1. Full help is available when you are ready to enter a command argument.

2. Partial help is provided when an abbreviated argument is entered.

Related Commands

(config) help

install

To install a new software image (such as the WAAS software) on the WAAS device, use the install EXEC command.

install filename

Syntax Description

filename

Specifies the name of the .bin file you want to install.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The install command loads the system image into flash memory and copies the disk-based software component to the software file system (swfs) partition. This command can also be used to install a BIOS or other firmware update by specifying the appropriate update file.

Note If you are installing a system image that contains optional software, make sure that an SWFS partition is mounted.

To install a system image, copy the image file to the SYSFS directory local1. Before executing the install command, change the present working directory to the directory where the system image resides. When the install command is executed, the image file is expanded. The expanded files overwrite the existing files on the WAAS device. The newly installed version takes effect after the system image is reloaded.

Note The install command does not accept.pax files. Files should be of the type.bin (for example, cache-sw.bin). Also, if the release being installed does not require a new system image, then it may not be necessary to write to flash memory. If the newer version has changes that require a new system image to be installed, then the install command may result in a write to flash memory.

Close your browser and restart the browser session to the WAAS Central Manager, if you installed a new software image to the primary WAAS Central Manager.

Examples

The following example shows how to load the system image contained in the wae512-cache-300.bin file:

WAE# install wae512-cache-300.bin

Related Commands

copy disk

reload

less

To display a file using the Less application, use the less EXEC command.

less file_name

Syntax Description

file_name

Name of the file to be displayed.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Less is a pager application that displays text files one page at a time. You can use Less to view the contents of a file, but not edit it. Less offers some additional features when compared to conventional text file viewer applications such as Type. These features include the following:

Backward movement—Allows you to move backward in the displayed text. Use k, Ctrl-k, y, or Ctrl-y to move backward. See the summary of Less commands for more details; to view the summary, press h or H while displaying a file in Less.
Searching and highlighting—Allows you to search for text in the file that you are viewing. You can search forward and backward. Less highlights the text that matches your search to make it easy to see where the match is.
Multiple file support—Allows you to switch between different files, remembering your position in each file. You can also do a search that spans all the files you are working with.

Examples

The following example shows how to display the text of the syslog.txt file using the Less application:

WAE# less syslog.txt

Related Commands

type

license add

To add a software license to a device, use the license add EXEC command.

license add license-name

Syntax Description

license-name

Name of the software license to add. The following license names are supported:

Transport—Enables basic DRE, TFO, and LZ optimization.
Enterprise—Enables the EPM, HTTP, MAPI, SSL, and Windows Print application accelerators, the WAAS Central Manager, and basic DRE, TFO, and LZ optimization.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to install the enterprise license:

WAE# license add Enterprise

Related Commands

clear arp-cache license

lls

To view a long list of directory names, use the lls EXEC command.

lls [ directory ]

Syntax Description

directory

(Optional) Name of the directory for which you want a long list of files.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The lls command provides detailed information about files and subdirectories stored in the present working directory (including the size, date, time of creation, SYSFS name, and long name of the file). This information can also be viewed with the dir command.

Examples

The following example shows how to display a detailed list of the files in the current directory:

WAE# lls

size time of last change name

-------------- ------------------------- -----------

4096 Fri Feb 24 14:40:00 2006 <DIR> actona

4096 Tue Mar 28 14:42:44 2006 <DIR> core_dir

4096 Wed Apr 12 20:23:10 2006 <DIR> crash

4506 Tue Apr 11 13:52:45 2006 dbupgrade.log

4096 Tue Apr 4 22:50:11 2006 <DIR> downgrade

4096 Sun Apr 16 09:01:56 2006 <DIR> errorlog

4096 Wed Apr 12 20:23:41 2006 <DIR> logs

16384 Thu Feb 16 12:25:29 2006 <DIR> lost+found

4096 Wed Apr 12 03:26:02 2006 <DIR> sa

24576 Sun Apr 16 23:54:30 2006 <DIR> service_logs

4096 Thu Feb 16 12:26:09 2006 <DIR> spool

9951236 Sun Apr 16 23:54:20 2006 syslog.txt

10026298 Thu Apr 6 12:25:00 2006 syslog.txt.1

4096 Thu Feb 16 12:29:30 2006 <DIR> var

508 Sat Feb 25 13:18:35 2006 wdd.sh.signed

Related Commands

dir

lls

ls

To view a list of files or subdirectory names within a directory on the device hard disk, use the ls EXEC command.

ls [ directory ]

Syntax Description

directory

(Optional) Name of the directory for which you want a list of files.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the ls directory command to list the filenames and subdirectories within a particular directory.

Use the ls command to list the filenames and subdirectories of the current working directory.

Use the pwd command to view the present working directory.

Examples

The following example shows how to display the files and subdirectories that are listed within the root directory:

WAE# ls

actona

core_dir

crash

dbupgrade.log

downgrade

errorlog

logs

lost+found

sa

service_logs

spool

syslog.txt

syslog.txt.1

var

wdd.sh.signed

Related Commands

dir

lls

pwd

lsusb

To view a list of files or subdirectory names within a directory on a USB storage device, use the lsusb EXEC command.

lsusb [ directory ]

Syntax Description

directory

(Optional) Name of the directory for which you want a list of files.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the lsusb directory command to list the filenames and subdirectories within a particular directory on the USB device.

Use the lsusb command to list the filenames and subdirectories of the current working directory on the USB device.

This command is available only on WAAS devices that support external USB storage devices.

Examples

The following example shows how to display the files and subdirectories that are listed within the root directory of a USB device:

WAE# lsusb

directory1

afile.txt

bfile.txt

Related Commands

dir

lls

pwd

mkdir

To create a directory, use the mkdir EXEC command.

mkdir directory

Syntax Description

directory

Name of the directory to create.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to create a new directory, oldpaxfiles :

WAE# mkdir /oldpaxfiles

Related Commands

cpfile

dir

lls

pwd

rename

rmdir

mkfile

To create a new file, use the mkfile EXEC command.

mkfile filename

Syntax Description

filename

Name of the file that you want to create.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the mkfile EXEC command to create a new file in any directory of the WAAS device.

Examples

The following example shows how to create a new file, traceinfo, in the root directory:

WAE# mkfile traceinfo

Related Commands

cpfile

dir

lls

mkdir

pwd

rename

ntpdate

To set the software clock (time and date) on a WAAS device using an NTP server, use the ntpdate EXEC command.

ntpdate { hostname | ip-address } [ key { authentication-key }]

Syntax Description

hostname	NTP hostname.
ip-address	NTP server IP (IPV4/IPv6) address.
key	(Optional) Specifies to use authentication with the NTP server.
authentication-key	Authentication key string to use with the NTP server authentication. This value must be between 0 and 4294967295.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the ntpdate command to find the current time of day and set the current time on the WAAS device to match. You must save the time to the hardware clock using the clock save command if you want to restore the time after a reload.

Examples

The following example shows how to set the software clock on the WAAS device using a NTP server:

WAE# ntpdate 10.11.23.40

Related Commands

clock

(config) clock

(config) ntp

show clock

show ntp

packet-capture

To capture packets on a device interface, use the packet-capture EXEC command.

packet-capture interface { GigabitEthernet slot/port | TenGigabitEthernet slot/port | PortChannel index | standby grpnumber } access-list { acl-name | acl-num }} [ file-size size [ number-of-files num | stop-after-num-files num ] ] | packet-size | non-encapsulated | [ capture-filename ]

packet-capture interface { GigabitEthernet slot/port | TenGigabitEthernet slot/port | PortChannel index | standby grpnumber } { access-list { acl-name | acl-num } | destination-ip { hostname | ip-address } | destination-port port | source-ip { hostname | ip-address } | source-port port } [ file-size size [ number-of-files num | stop-after-num-files num ] ] | packet-size | non-encapsulated | [ capture-filename ]

packet-capture decode [ destination-ip { hostname | ip-address } | destination-port port | source-ip { hostname | ip-address } | source-port port ] [ file-size size [ number-of-files num | stop-after-num-files num ] ] | packet-size | non-encapsulated | capture-filename

Syntax Description

interface	Specifies the source interface from which to capture packets.
GigabitEthernet slot/port	Specifies a Gigabit Ethernet interface. The slot number and port number are separated with a forward slash character (/).
TenGigabitEthernet slot/port	Specifies a 10-Gigabit Ethernet interface. The slot number and port number are separated with a forward slash character (/).
PortChannel index	Specifies a port channel interface (1-4).
standby grpnumber	Specifies a standby group (1-2).
access-list	Specifies an access list for which to capture packets on the specified interface.
file-size size	(Optional) Specifies the maximum file size for captured output, from 1–100000 KB. After a file fills to capacity, another output file is created according to the following keywords.
number-of-files num	(Optional) Specifies the maximum number of output files to create (1–500), after which earlier files are overwritten as needed for more captured data.
stop-after-num-files num	(Optional) Specifies the maximum number of output files to create (1–500), after which packet capture is stopped.
packet-size	The maximum number of capture bytes per packet.
non-encapsulated	Captures packets that are not SIA encapsulated.
capture-filename	(Optional) Specifies the name of a file to which output is saved. If no file is specified, output is sent to the console.
destination-ip	Captures packets matching the specified destination IPv4 or IPv6 address.
hostname	Captures packets matching the specified destination or source hostname.
ip-address	Destination or source IP address.
destination-port port	Captures packets matching the specified destination port.
source-ip	Captures packets matching the specified source IPv4 or IPv6 address.
source-port port	Captures packets matching the specified source port.
decode	Decodes captured packets.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

The following are usage guidelines for the packet-capture command:

Either packet capture or debug capture can be active, but not both simultaneously.

The packet-capture command is preferred over the deprecated commands tcpdump and tethereal,

For WAAS Version 6.2.1 and later, you can run the packet-capture command in multiple sessions (telnet or ssh) on the same or different interfaces, up to a maximum of five sessions, that print in the WAE.

Examples

The following example shows how to capture packets on a normal interface:

WAE(config)# ip access-list extended 100 permit tcp any any range 23 35

WAE(config)# exit

WAE# packet-capture interface gig 0/1 access-list 100 mycapture

Related Commands

tcpdump

tethereal

ping

To send echo packets for diagnosing basic network connectivity on networks, use the ping EXEC command.

ping [ management ] { hostname | ip-address }

Syntax Description

management	Uses the designated management interface for the ping.
hostname	Hostname of system to ping.
ip-address	IP address of system to ping.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To use the ping command with the hostname argument, make sure that DNS functionality is configured on the WAAS device. To force the timeout of a nonresponsive host, or to eliminate a loop cycle, press Ctrl-C.

Examples

The following example shows how to send echo packets to a machine with address 172.19.131.189 to verify its availability on the network:

WAE# ping 172.19.131.189

PING 172.19.131.189 (172.19.131.189) from 10.1.1.21 : 56(84) bytes of

data.

64 bytes from 172.19.131.189: icmp_seq=0 ttl=249 time=613 usec

64 bytes from 172.19.131.189: icmp_seq=1 ttl=249 time=485 usec

64 bytes from 172.19.131.189: icmp_seq=2 ttl=249 time=494 usec

64 bytes from 172.19.131.189: icmp_seq=3 ttl=249 time=510 usec

64 bytes from 172.19.131.189: icmp_seq=4 ttl=249 time=493 usec

--- 172.19.131.189 ping statistics ---

5 packets transmitted, 5 packets received, 0% packet loss

round-trip min/avg/max/mdev = 0.485/0.519/0.613/0.047 ms

WAE#

Related Commands

traceroute

ping6

To send echo packets for diagnosing basic network connectivity on IPv6 networks, use the ping6 EXEC command.

ping6 { hostname | ip-address }[ management ]

Syntax Description

hostname	Hostname of system to ping.
ip-address	IPv6 address of system to ping.
management	Uses the designated management interface for the ping.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To use the ping6 command with the hostname argument, make sure that DNS functionality is configured on the WAAS device. To force the timeout of a nonresponsive host, or to eliminate a loop cycle, press Ctrl-C.

When you use a device’s management interface to establish connectivity to another device, using ping6 command, and the management interface goes down, the communication will still succeed if the address of the end device is reachable from any other interface.

Examples

The following example shows how to send echo packets to a machine with address 2013:1:1:10::5

to verify its availability on the network:

WAE# ping 2013:1:1:10::5

PING 2013:1:1:10::5(2013:1:1:10::5) 56 data bytes

64 bytes from 2013:1:1:10::5: icmp_seq=1 ttl=64 time=0.018 ms

64 bytes from 2013:1:1:10::5: icmp_seq=2 ttl=64 time=0.037 ms

64 bytes from 2013:1:1:10::5: icmp_seq=3 ttl=64 time=0.028 ms

64 bytes from 2013:1:1:10::5: icmp_seq=4 ttl=64 time=0.029 ms

64 bytes from 2013:1:1:10::5: icmp_seq=5 ttl=64 time=0.029 ms

--- 2013:1:1:10::5 ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 3999ms

rtt min/avg/max/mdev = 0.018/0.028/0.037/0.006 ms

Related Commands

traceroute6

pwd

To view the present working directory on a WAAS device, use the pwd EXEC command.

pwd

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Examples

The following example shows how to display the current working directory:

WAE# pwd

/local1

Related Commands

dir

lls

reload

To halt the operation and perform a cold restart on a WAAS device, use the reload EXEC command.

reload [ force | in m | cancel ]

Syntax Description

force	(Optional) Forces a reboot without further prompting.
in m	(Optional) Schedules a reboot after a specified interval (1-10080 minutes).
cancel	(Optional) Cancels a scheduled reboot.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

To reboot a WAAS device, use the reload command. If no configurations are saved to flash memory, you are prompted to enter configuration parameters upon a restart. Any open connections are dropped after you enter the reload command, and the file system is reformatted upon restart.

The reload command can include the option to schedule a reload of the software to take effect in a specified number of minutes. After entering this command, you are asked to confirm the reload by typing y and then confirm WCCP shutdown by typing y again (if WCCP is active).

You can use the cancel option to cancel a scheduled reload.

Examples

The following example shows how to halt the operation of the WAAS device and reboot with the configuration saved in flash memory. You are not prompted for confirmations during the process.

WAE# reload force

Related Commands

write

rename

To rename a file on a WAAS device, use the rename EXEC command.

rename oldfilename newfilename

Syntax Description

oldfilename	Original filename.
newfilename	New filename.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the rename command to rename any SYSFS file without making a copy of the file.

Examples

The following example shows how to rename the errlog.txt file to old_errlog.txt :

WAE# rename errlog.txt old_errlog.txt

Related Commands

cpfile

restore

To restore the device to its manufactured default status by removing the user data from the disk and flash memory, use the restore EXEC command.

restore { factory-default [ preserve basic-config ] | rollback }

Syntax Description

factory-default	Resets the device configuration and data to their manufactured default status.
preserve	(Optional) Preserves certain configurations and data on the device.
basic-config	(Optional) Selects basic network configurations.
rollback	Rolls back the configuration to the last functional software and device configuration.

Defaults

No default behavior or values.

Command Modes

EXEC

Device Modes

application-accelerator

central-manager

Usage Guidelines

Use the restore EXEC command to restore data on a disk and in flash memory to the factory default, while preserving particular time-stamp evaluation data, or to roll back the configuration to the last functional data and device configuration.

This command erases all existing content on the device; however, your network settings are preserved and the device is accessible through a Telnet and Secure Shell (SSH) session after it reboots.

Backing up the Central Manager Database

Before you use the restore factory-default command on your primary WAAS Central Manager or change over from the primary to a standby WAAS Central Manager, make sure that you back up the WAAS Central Manager database and copy the backup file to a safe location that is separate from the WAAS Central Manager. You must halt the operation of the WAAS Central Manager before you enter the backup and restore commands.

Caution

The restore command erases user-specified configuration information stored in the flash image and removes data from a disk, user-defined disk partitions, and the entire Central Manager database. User-defined disk partitions that are removed include the SYSFS, WAAS, and PRINTSPOOLFS partitions. The configuration that is removed includes the starting configuration of the device.

By removing the WAAS Central Manager database, all configuration records for the entire WAAS network are deleted. If you do not have a valid backup file or a standby WAAS Central Manager, you must reregister every WAE with the WAAS Central Manager because all previously configured data is lost.

If you used your standby WAAS Central Manager to store the database while you reconfigured the primary, you can register the former primary as a new standby WAAS Central Manager.

If you created a backup file while you configured the primary WAAS Central Manager, you can copy the backup file to this newly reconfigured WAAS Central Manager.

Rolling Back the Configuration

You can roll back the software and configuration of a WAAS device to a previous version using the restore rollback command. You would roll back the software only in cases in which a newly installed version of the WAAS software is not functioning properly.

The restore rollback command installs the last saved WAAS.bin image on the system disk. A WAAS.bin image is created during software installation and stored on the system disk. If the WAAS device does not have a saved version, the software is not rolled back.

Note WAFS to WAAS migration is supported. Rollback from WAAS to WAFS is not supported.

Examples

The following examples show how to use the restore factory-default and restore factory-default preserve basic-config commands. Because configuration parameters and data are lost, prompts are given before initiating the restore operation to ensure that you want to proceed.

WAE# restore factory-default

This command will wipe out all of data on the disks

and wipe out WAAS CLI configurations you have ever made.

If the box is in evaluation period of certain product,

the evaluation process will not be affected though.

It is highly recommended that you stop all active services

before this command is run.

Are you sure you want to go ahead?[yes/no]

WAE# restore factory-default preserve basic-config

This command will wipe out all of data on the disks

and all of WAAS CLI configurations except basic network

configurations for keeping the device online.

The to-be-preserved configurations are network interfaces,

default gateway, domain name, name server and hostname.

If the box is in evaluation period of certain product,

the evaluation process will not be affected.

It is highly recommended that you stop all active services

before this command is run.

Are you sure you want to go ahead?[yes/no]

Note You can enter basic configuration parameters (such as the IP address, hostname, and name server) at this point, or you can enter these parameters later through entries in the command-line interface.

The following example shows how to verify that the restore command has removed data from the SYSFS, WAAS, and PRINTSPOOLFS partitioned file systems:

WAE# show disks details

Physical disk information:

disk00: Normal (h00 c00 i00 l00 - DAS) 140011MB(136.7GB)

disk01: Normal (h00 c00 i01 l00 - DAS) 140011MB(136.7GB)

Mounted filesystems:

MOUNT POINT TYPE DEVICE SIZE INUSE FREE USE%

/ root /dev/root 35MB 30MB 5MB 85%

/swstore internal /dev/md1 991MB 333MB 658MB 33%

/state internal /dev/md2 3967MB 83MB 3884MB 2%

/disk00-04 CONTENT /dev/md4 122764MB 33MB 122731MB 0%

/local/local1 SYSFS /dev/md5 3967MB 271MB 3696MB 6%

.../local1/spool PRINTSPOOL /dev/md6 991MB 16MB 975MB 1%

/sw internal /dev/md0 991MB 424MB 567MB 42%

Software RAID devices:

DEVICE NAME TYPE STATUS PHYSICAL DEVICES AND STATUS

/dev/md0 RAID-1 NORMAL OPERATION disk00/00[GOOD] disk01/00[GOOD]

/dev/md1 RAID-1 NORMAL OPERATION disk00/01[GOOD] disk01/01[GOOD]

/dev/md2 RAID-1 NORMAL OPERATION disk00/02[GOOD] disk01/02[GOOD]

/dev/md3 RAID-1 NORMAL OPERATION disk00/03[GOOD] disk01/03[GOOD]

/dev/md4 RAID-1 NORMAL OPERATION disk00/04[GOOD] disk01/04[GOOD]

/dev/md5 RAID-1 NORMAL OPERATION disk00/05[GOOD] disk01/05[GOOD]

/dev/md6 RAID-1 NORMAL OPERATION disk00/06[GOOD] disk01/06[GOOD]

Currently content-filesystems RAID level is not configured to change.

The following example shows how to upgrade or restore an older version of the WAAS software. In the example, version Y of the software is installed (using the copy command), but the administrator has not switched over to it yet, so the current version is still version X. The system is then reloaded (using the reload command), and it verifies that version Y is the current version running.

The following example shows how to roll back the software to version X (using the restore rollback command), and reload the software:

WAE# copy ftp install server path waas.versionY.bin

WAE# show version

Cisco Wide Area Application Services Software (WAAS)

Cisco Wide Area Application Services Software Release 4.0.0 (build b340 Mar 25 2

006)

Version: oe612-4.0.0.340

Compiled 17:26:17 Mar 25 2006 by cnbuild

System was restarted on Mon Mar 27 15:25:02 2006.

The system has been up for 3 days, 21 hours, 9 minutes, 17 seconds.

WAE# show version last

Nothing is displayed.

WAE# show version pending

WAAS 4.0.1 Version Y

WAE# reload

...... reloading......

WAE# show version

Cisco Wide Area Application Services Software (WAAS)

...

WAE# restore rollback

WAE# reload

...... reloading......

Because flash memory configurations were removed after the restore command was used, the show startup-config command does not return any flash memory data. The show running-config command returns the default running configurations.

Related Commands

reload

show disks