D Commands

dampen-igp-metric

dampen-igp-metric <sec> | no dampen-igp-metric

Syntax Description

no

Negate a command or set its defaults

dampen-igp-metric

Dampen IGP metric-related changes

sec

Time interval in seconds

Command Mode

  • /exec/configure/router-bgp/router-bgp-af

dampening

[no] dampening | dampening [ { <half-life> [ { <reuse> <suppress> <max-suppress> } [ restart [ <penalty> ] ] ] } ]

Syntax Description

no

Negate a command or set its defaults

dampening

configures dampenning feature

half-life

(Optional) half-life time for the penalty

reuse

(Optional) Value to start reusing an interface

suppress

(Optional) Value to start suppressing an interface

max-suppress

(Optional) Maximum duration to suppress an interface

restart

(Optional) Enable restart penalty

penalty

(Optional) Penalty applied at restart

Command Mode

  • /exec/configure/if-igp

dampening

[no] dampening [ { <half-life> <reuse-limit> <suppress-limit> <max-suppress-time> } | { route-map <rmap-name> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

dampening

Configure route flap dampening

half-life

(Optional) Decay half life

reuse-limit

(Optional) Value to start reusing a route

suppress-limit

(Optional) Value to start suppressing a route

max-suppress-time

(Optional) Maximum suppress time for stable route

route-map

(Optional) Apply route-map to specify dampening criteria

rmap-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-ipv4-mdt

dampening

[no] dampening [ { <half-life> <reuse-limit> <suppress-limit> <max-suppress-time> } | { route-map <rmap-name> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

dampening

Configure route flap dampening

half-life

(Optional) Decay half life

reuse-limit

(Optional) Value to start reusing a route

suppress-limit

(Optional) Value to start suppressing a route

max-suppress-time

(Optional) Maximum suppress time for stable route

route-map

(Optional) Apply route-map to specify dampening criteria

rmap-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls

data-pattern

{ { no | default } data-pattern | data-pattern <hex-pattern> }

Syntax Description

no

default

Set a command to its defaults

data-pattern

Data Pattern

hex-pattern

Data Pattern in Hex

Command Mode

  • /exec/configure/ip-sla/udp

data-pattern pad

{ data-pattern pad <pad-val> }

Syntax Description

data-pattern

Configure NGOAM ping payload

pad

Configure NGOAM payload test pattern pad

pad-val

Configure NGOAM payload test pad value

Command Mode

  • /exec/configure/configngoamconnectcheck

data-source

{ data-source <type> } | { no data-source [ <type> ] }

Syntax Description

no

Negate a command or set its defaults

data-source

Specify the data source

type

Command Mode

  • /exec/configure/telemetry/sensor-group

database-mapping

{ [ no ] database-mapping { <eid-prefix> | <eid-prefix6> } { redistribute | { { <locator> | <locator6> } priority <priority> weight <weight> } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

database-mapping

Configure EID-prefix and locator-set for dynamic-EID

eid-prefix

IP EID-prefix for RLOC static mapping

locator

IP address of LISP-VM routers

priority

Configures which Locators from a set are preferred

priority

Lower priority Locator takes preference

weight

Traffic load-spreading among Locators

weight

Specified in a percentage from 0 to 100

redistribute

Used for redistirbuting into routing protocols

Command Mode

  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

databits

[no] databits <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

databits

Set number of databits per character

i0

Number of data bits

Command Mode

  • /exec/configure/console

databits

[no] databits <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

databits

Set number of databits per character

i0

Number of data bits

Command Mode

  • /exec/configure/com1

datapath-id

datapath-id <datapathid-val> | no datapath-id

Syntax Description

no

Negate a command or set its defaults

datapath-id

Datapath ID

datapathid-val

64-bit hex value [0x1-0xffffffffffffffff]

Command Mode

  • /exec/configure/openflow/switch

datapath-id

datapath-id <datapathid-val> | no datapath-id

Syntax Description

no

Negate a command or set its defaults

datapath-id

Datapath ID

datapathid-val

64-bit hex value [0x1-0xffffffffffffffff]

Command Mode

  • /exec/configure/openflow/switch/sub-switch

dataplane mpls

[no] dataplane mpls

Syntax Description

no

(Optional) Negate a command or set its defaults

dataplane

Dataplane Candidate path-option

mpls

MPLS Dataplane Candidate path-option

Command Mode

  • /exec/configure/sr/te/color/cndpaths/pref/constraint/sgmnt

dataplane mpls

[no] dataplane mpls

Syntax Description

no

(Optional) Negate a command or set its defaults

dataplane

Dataplane Candidate path-option

mpls

MPLS Dataplane Candidate path-option

Command Mode

  • /exec/configure/sr/te/pol/cndpaths/pref/constraint/sgmnt

db-jid

[no] db-jid <jid> [ key-type <key-type> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-jid

Jabber ID of database

jid

Enter Jabber ID of database

key-type

(Optional) Query key type for this database

key-type

(Optional)

Command Mode

  • /exec/configure/fabric-db/server-xmpp

db-security user password

[no] db-security user <user> password { 0 <clear> | 7 <encrypted> | <password> } [ shared-secret { 10 <clear> | 7 <encrypted> | <secret> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-security

Database Security

user

User ID

user

Enter user ID

password

Password

0

Password that follows should be in clear text

clear

Password in clear text

7

Password that follows should be in encrypted text

encrypted

Encrypted password

password

Enter password in clear text

shared-secret

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

10

(Optional) Indicates that password that follows should be in clear text

clear

(Optional) Password in clear text

7

(Optional) Password that follows should be in encrypted text

encrypted

(Optional) Encrypted password

secret

(Optional) Enter shared-secret in clear text

Command Mode

  • /exec/configure/fabric-db/server-ldap

db-table

[no] db-table <tablename> [ key-type <key-type> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-table

Table name to search

tablename

Enter table name to search

key-type

(Optional) Query key type for this table

key-type

(Optional)

Command Mode

  • /exec/configure/fabric-db/server-ldap

dchal module

dchal module <module> <quoted-cmd>

Syntax Description

dchal

dchal shell/cmd

module

Module number of the linecard

module

Enter module number

quoted-cmd

the command to run on dchal

Command Mode

  • /exec

dchal module

dchal module <module>

Syntax Description

dchal

dchal shell/cmd

module

Module number of the linecard

module

Enter module number

Command Mode

  • /exec

dci-advertise-pip

[no] dci-advertise-pip

Syntax Description

no

(Optional) Negate a command or set its defaults

dci-advertise-pip

Advertise-PIP towards DCI

Command Mode

  • /exec/configure/config-evpn-msite-bgw

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes

Command Mode

  • /exec/configure/radius

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes

Command Mode

  • /exec/configure/ldap

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes

Command Mode

  • /exec/configure/tacacs+

default-information originate

[no] default-information originate [ always ] [ route-map <policy-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default route

originate

Distribute a default route

always

(Optional) Always advertise default route

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

default-information originate

[no] default-information originate [ always ] [ route-map <map-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

RIP control distribution of default route

originate

RIP distribute a default route

always

(Optional) RIP always advertise default route

route-map

(Optional) Policy to constrain redistribution

map-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

default-information originate

[no] default-information originate [ always ] [ route-map <map-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control origination of a default route

originate

Originate a default route

always

(Optional) Always advertise default route

route-map

(Optional) Route-map to announce default routes

map-name

(Optional) A 'routing-rules' route-map name

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv4 /exec/configure/router-isis/router-isis-af-ipv6

default-information originate

[no] default-information originate [ always ] [ route-map <policy-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default route

originate

Distribute a default route

always

(Optional) Always advertise default route

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

default-information originate

[no] default-information originate [ always ] [ route-map <map> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control origination of a default route

originate

Originate a default route

always

(Optional) Always advertise default route

route-map

(Optional) Use a route-map for default route metrics

map

(Optional) Route-map name

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

default-information originate

[no] default-information originate

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default information

originate

Distribute a default route

Command Mode

  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-ipv4-label

default-information originate always rd route-target

[no] default-information originate always rd { <ext-comm-rd-aa2nn4> | <ext-comm-rd-aa4nn2> } route-target { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> }

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default information

originate

Distribute a default route

always

Always advertise default route

rd

VPN Route Distinguisher

ext-comm-rd-aa4nn2

VPN route distinguisher in aa4:nn or ip:nn format

ext-comm-rd-aa2nn4

VPN route distinguisher in aa:nn format

route-target

Specify Target VPN Extended Communities

ext-comm-rt-aa4nn2

RT extcommunity in aa4:nn or ip:nn format

ext-comm-rt-aa2nn4

RT extcommunity in aa:nn format

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6

default-metric

default-metric <metric> | no default-metric [ <metric> ]

Syntax Description

no

Negate a command or set its defaults

default-metric

RIP default metric

metric

RIP metric value

Command Mode

  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

default-metric

{ default-metric <cost> } | { no default-metric [ <cost> ] }

Syntax Description

no

Negate a command or set its defaults

default-metric

Specify default metric for redistributed routes

cost

Metric value

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

default-metric

{ { default-metric <bw> <delay> <rel> <load> <mtu> } | { no default-metric [ <bw> <delay> <rel> <load> <mtu> ] } }

Syntax Description

no

Negate a command or set its defaults

default-metric

Set metric of redistributed routes

bw

Bandwidth in Kbits per second

delay

Delay metric

rel

Reliability metric where 255 is 100% reliable

load

Effective bandwidth metric (Loading) where 255 is 100% loaded

mtu

Maximum Transmission Unit metric of the path

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

default-metric

{ default-metric <cost> } | { no default-metric [ <cost> ] }

Syntax Description

no

Negate a command or set its defaults

default-metric

Specify default metric for redistributed routes

cost

Metric value

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

default-metric

[no] default-metric <metric>

Syntax Description

no

(Optional) Negate a command or set its defaults

default-metric

Set metric of redistributed routes

metric

Default Metric

Command Mode

  • /exec/configure/router-bgp/router-bgp-af

default-miss

default-miss { continue-drop | continue-normal | continue-controller | drop | normal | controller } | no default-miss

Syntax Description

no

Negate a command or set its defaults

default-miss

Set continue-drop/continue-normal/continue-controller/drop/normal/controller flow action

continue-drop

cascade drop to next table

continue-normal

cascade normal to next table

continue-controller

cascade punt to next table

drop

drop packet

normal

forward to normal dataplane

controller

punt to controller

Command Mode

  • /exec/configure/openflow/switch

default-originate

[ no | default ] default-originate [ route-map <rmap-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

default-originate

Originate a default toward this peer

route-map

(Optional) Route-map to specify criteria for originating default

rmap-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label

default-route nssa-abr pbit-clear

[no] default-route nssa-abr pbit-clear

Syntax Description

no

(Optional) Negate a command or set its defaults

default-route

Control default-route addition

nssa-abr

On area border router with NSSA areas

pbit-clear

Allow addition even If p-bit in type-7 external LSA is clear

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

default-route nssa-abr pbit-clear

[no] default-route nssa-abr pbit-clear

Syntax Description

no

(Optional) Negate a command or set its defaults

default-route

Control default-route addition

nssa-abr

On area border router with NSSA areas

pbit-clear

Allow addition even If p-bit in type-7 external LSA is clear

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-host-policy/receiver

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-host-policy/sender

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-vrf/nbm-host-policy/sender

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-vrf/nbm-host-policy/receiver

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-host-policy/pim

default permit

[no] default { permit | deny }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Default Host Admission Policy

permit

Admission Permitted

deny

Admission Denied

Command Mode

  • /exec/configure/nbm-vrf/nbm-host-policy/pim

define

[no] define <paramname> [ <paramtype> ] [ <paramdesc> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

define

Define a parameter

paramname

Enter the name of the parameter

paramtype

(Optional) param type

paramdesc

(Optional) Enter the parameter description

Command Mode

  • /exec/configure/param-list

delay-response duration

[no] delay-response duration <sec> [ renew-offset <off> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

delay-response

delay-response

duration

session duration

renew-offset

(Optional) session duration renewal offset

sec

seconds

off

(Optional) offset

Command Mode

  • /exec/configure/ptp-ucast-nego-schema

delay-response duration range

[no] delay-response duration range <min> <max>

Syntax Description

no

(Optional) Negate a command or set its defaults

delay-response

delay-response

duration

session duration

range

range of acceptable values

min

minimum in seconds

max

maximum in seconds

Command Mode

  • /exec/configure/ptp-ucast-nego-schema

delay-response interval

[no] delay-response interval <intv>

Syntax Description

no

(Optional) Negate a command or set its defaults

delay-response

delay-response

interval

interval

intv

log seconds

Command Mode

  • /exec/configure/ptp-ucast-nego-schema

delay-response interval range

[no] delay-response interval range <min> <max>

Syntax Description

no

(Optional) Negate a command or set its defaults

delay-response

delay-response

interval

interval

range

range of acceptable values

min

minimum in log seconds

max

maximum in log seconds

Command Mode

  • /exec/configure/ptp-ucast-nego-schema

delay-restore time

[no] delay-restore time <sec>

Syntax Description

no

(Optional) Negate a command or set its defaults

delay-restore

delay-restore

time

time

sec

time in seconds

Command Mode

  • /exec/configure/config-evpn-msite-bgw

delay

delay <microseconds> | no delay

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

microseconds

Throughput delay (tens of microseconds)

Command Mode

  • /exec/configure/if-vlan-common

delay

delay <delay_val> | no delay [ <delay_val> ]

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

delay_val

Throughput delay (tens of microseconds)

Command Mode

  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub

delay

delay <delay_val> | no delay [ <delay_val> ]

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

delay_val

Throughput delay (tens of microseconds)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-range

delay

delay { { { up { <up_delay> | { milliseconds <up_delay_ms> } } } [ down { <down_delay> | { milliseconds <down_delay_ms> } } ] } | { { down { <down_delay> | { milliseconds <down_delay_ms> } } } [ up { <up_delay> | { milliseconds <up_delay_ms> } } ] } } | no delay [ { { up { <up_delay> | { milliseconds <up_delay_ms> } } } [ down { <down_delay> | { milliseconds <down_delay_ms> } } ] } | { { down { <down_delay> | { milliseconds <down_delay_ms> } } } [ up { <up_delay> | { milliseconds <up_delay_ms> } } ] } ]

Syntax Description

no

Negate a command or set its defaults

delay

Tracking delay

up

Delay up change notification

up_delay

Seconds to delay

up_delay_ms

Milliseconds to delay

down

(Optional) Delay down change notification

down_delay

(Optional) Seconds to delay

down_delay_ms

(Optional) Milliseconds to delay

milliseconds

Frequency will be taken as milliseconds

Command Mode

  • /exec/configure/track /exec/configure/tr-list-bool /exec/configure/tr-list-thrp /exec/configure/tr-list-thrw

delay peer-link

delay peer-link <time> | no delay peer-link

Syntax Description

no

Negate a command or set its defaults

delay

Peer-link bringup delay

peer-link

Delay peer-link bringup

time

Delay in bringing up the peer-link (in seconds)

Command Mode

  • /exec/configure/vpc-domain

delay restore

delay restore <time-out> | no delay restore

Syntax Description

no

Negate a command or set its defaults

delay

Initialization delay

restore

Delay after restoring peer-link

time-out

Delay in bringing up the vPC links (in seconds)

Command Mode

  • /exec/configure/vpc-domain

delay restore interface-vlan

delay restore interface-vlan <time-out> | no delay restore interface-vlan

Syntax Description

no

Negate a command or set its defaults

delay

Initialization delay

restore

Delay after restoring peer-link

interface-vlan

Delay in bringing-up interface-vlan

time-out

Delay in bringing up the interface-vlan (in seconds)

Command Mode

  • /exec/configure/vpc-domain

delay restore orphan-port

delay restore orphan-port <delay_time> | no delay restore orphan-port

Syntax Description

no

Negate a command or set its defaults

delay

Initialization delay

restore

Delay after restoring peer-link

orphan-port

Configure vPC orphan-port delay bring-up timer

delay_time

Specify delay time in seconds

Command Mode

  • /exec/configure/vpc-domain

delete

delete { <uri0> | <uri1> | <uri2> } [ no-prompt ]

Syntax Description

delete

delete a file or directory

uri0

Delete a file or directory

uri1

Delete a file or directory on expansion flash

uri2

Directory or filename on logflash

no-prompt

(Optional) Do not prompt for multiple deletion of files

Command Mode

  • /exec

delete ca-certificate

delete ca-certificate

Syntax Description

delete

Delete the certificates

ca-certificate

Delete the ca certificates

Command Mode

  • /exec/configure/trustpoint

delete certificate

delete certificate [ force ]

Syntax Description

delete

Delete the certificates

certificate

Delete the identity certificate

force

(Optional) Force delete the identity certificate

Command Mode

  • /exec/configure/trustpoint

delete crl

delete crl

Syntax Description

delete

Delete the certificates

crl

Delete the CRL

Command Mode

  • /exec/configure/trustpoint

demand-circuit

[no] demand-circuit

Syntax Description

no

(Optional) Negate a command or set its defaults

demand-circuit

OSPF Demand circuit

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

depth

{ [ no ] depth <cells> | no depth }

Syntax Description

depth

Provide the number of cells for this POSTCARD queue_profile

cells

queue_profile depth (number of cells/packets). Default is 300

Command Mode

  • /exec/configure/config-postcard-q-prof

depth

{ [ no ] depth <cells> | no depth }

Syntax Description

depth

Provide the number of cells for this INT queue_profile

cells

queue_profile depth (number of cells). Default is 300

Command Mode

  • /exec/configure/config-int-q-prof

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Table-Map description

desc-str

Description of this table-map (up to 200 characters)

Command Mode

  • /exec/configure/table-map

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this INT queue_profile

line

queue_profile description string (63 characters maximum)

Command Mode

  • /exec/configure/config-int-q-prof

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this INT flow-profile

line

flow-profile description string (63 characters maximum)

Command Mode

  • /exec/configure/config-int-flow-prof

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Record

line

Record description string (63 characters maximum)

Command Mode

  • /exec/configure/config-fte-record

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this FTE Monitor

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/config-fte-monitor

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this FTE Eveny

line

Event description string (63 characters maximum)

Command Mode

  • /exec/configure/config-fte-event

description

{ description <line> | no description }

Syntax Description

no

Negate a command or set its defaults

description

Description of the route-map

line

Route-map description string

Command Mode

  • /exec/configure/route-map

description

{ [ no ] description <text> }

Syntax Description

description

description for this profile

text

description

Command Mode

  • /exec/configure/dot1x-cred

description

{ description <descr> } | { no description }

Syntax Description

description

Configure description of the profile

descr

Description of maximum 64 characters

Command Mode

  • /exec/configure/configngoamprofile

description

description <descr> | no description

Syntax Description

no

Negate a command or set its defaults

description

Session description (max 32 characters)

descr

Enter the description string(can include spaces)

Command Mode

  • /exec/configure/monitor-common

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters

Command Mode

  • /exec/configure/if-any-tunnel

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)

Command Mode

  • /exec/configure/class-map

description

[no] description <desc-str>

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)

Command Mode

  • /exec/configure/class-map/type/queuing

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Policy-Map description

desc-str

Description of this policy-map (up to 200 characters)

Command Mode

  • /exec/configure/policy-map

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Policy-Map description

desc-str

Description of this policy-map (up to 200 characters)

Command Mode

  • /exec/configure/policy-map/type/queuing

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Record

line

Record description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-record

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Monitor

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-monitor

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Exporter

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-exporter

description

description [ port-profile ] <desc_line> | no description [ port-profile ] [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter port-profile description of maximum 80 characters

port-profile

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

desc_line

Enter port-profile description of maximum 80 characters

Command Mode

  • /exec/configure/port-profile

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)

Command Mode

  • /exec/configure/class-map/type/uf

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Policy-Map description

desc-str

Description of this policy-map (up to 200 characters)

Command Mode

  • /exec/configure/policy-map/type/uf

description

description <desc> | no description

Syntax Description

no

Negate a command or set its defaults

description

Fabric Path topology description

desc

Description of maximum 80 characters

Command Mode

  • /exec/configure/fp-topology

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this collector

line

Collector description string (63 characters maximum)

Command Mode

  • /exec/configure/config-buffer-latency-collector

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this buffer-latency record

line

Record description string (63 characters maximum)

Command Mode

  • /exec/configure/config-buffer-latency-record

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this buffer-latency Monitor

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/config-buffer-latency-monitor

description

[no] description <description>

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Configure description for the policy

description

Description for the policy

Command Mode

  • /exec/configure/event-manager-applet

description

[no] description

Syntax Description

no

Negate a command or set its defaults

description

Configure description for the policy

Command Mode

  • /exec/configure/event-manager-applet

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Exporter

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-exporter

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Record

line

Record description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-record

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Monitor

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-monitor

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Event

line

Event description string (63 characters maximum)

Command Mode

  • /exec/configure/nfm-event

description

description <desc_line> | no description

Syntax Description

no

Negate a command or set its defaults

description

Interface specific description

desc_line

Up to 255 characters describing this interface

Command Mode

  • /exec/configure/if-vlan-common

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this POSTCARD queue_profile

line

queue_profile description string (63 characters maximum)

Command Mode

  • /exec/configure/config-postcard-q-prof

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this POSTCARD flow-profile

line

flow-profile description string (63 characters maximum)

Command Mode

  • /exec/configure/config-postcard-flow-prof

description

description <line> | no description

Syntax Description

no

Negate a command or set its defaults

description

Add a description for the role

line

Enter the description string(can include spaces)

Command Mode

  • /exec/configure/role

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-eth-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-ethernet-p2p /exec/configure/if-ether-sub-p2p /exec/configure/if-loopback /exec/configure/if-ethernet-all /exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-range

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters

Command Mode

  • /exec/configure/if-mgmt-ether

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters

Command Mode

  • /exec/configure/if-nve

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 80 characters

desc_line

Description of maximum 80 characters

Command Mode

  • /exec/configure/if-overlay /exec/configure/if-te

description

[no] description [ <desc> ] | description <desc>

Syntax Description

no

Negate a command or set its defaults

description

Group description

desc

(Optional) Up to 80 characters describing this group

Command Mode

  • /exec/configure/if-eth-any/vrrpv3

description

[no] description [ <desc> ] | description <desc>

Syntax Description

no

Negate a command or set its defaults

description

Pathway description

desc

(Optional) Up to 80 characters describing this pathway

Command Mode

  • /exec/configure/if-eth-any/vrrs

description

{ description <line> } | { no description }

Syntax Description

no

Negate a command or set its defaults

description

Description of the VRF

line

VRF description string

Command Mode

  • /exec/configure/vrf

description

{ [ no ] description <descrip-string> }

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Provide a description string for the LISP site

descrip-string

Description string

Command Mode

  • /exec/configure/lisp-site /exec/configure/vrf/lisp-site

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this collector

line

Collector description string (63 characters maximum)

Command Mode

  • /exec/configure/config-buffer-drop-collector

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this buffer-drop Monitor

line

Monitor description string (63 characters maximum)

Command Mode

  • /exec/configure/config-buffer-drop-monitor

description

description <describe> | no description

Syntax Description

no

Negate a command or set its defaults

description

Description for the BMP server

describe

Upto 80 characters describing this server

Command Mode

  • /exec/configure/router-bgp/router-bgp-bmp-server

description

description <describe> | { no | default } description [ <describe> ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

description

Neighbor specific description

describe

Upto 80 characters describing this neighbor

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

dest-ipaddr

{ dest-ipaddr { <ip-address> | <hostname> } }

Syntax Description

dest-ipaddr

Destination ip address

ip-address

IP address, broadcast disallowed

hostname

IP Hostname, broadcast disallowed

Command Mode

  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter

dest-ipaddr

{ dest-ipaddr { <ip-address> | <hostname> | <ipv6-address> } }

Syntax Description

dest-ipaddr

Destination ip address

ip-address

IP address, broadcast disallowed

hostname

IP Hostname, broadcast disallowed

Command Mode

  • /exec/configure/ip-sla/tcp

dest-port

{ dest-port <port> }

Syntax Description

dest-port

Destination port

port

udp port number

Command Mode

  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp

dest

{ dest { { ip { <numeric10> | <numeric11> | unknown } } | { mac <dmac> <dot1qid> [ <intfid> ] } } }

Syntax Description

dest

destination node

ip

ip address

numeric10

Ipv4 address of remote host / VTEP

unknown

Peer vtep ip is unknown, Applicable only for channel Nv03

mac

Mac

dmac

Destination mac address

dot1qid

Encapsulation dot1q/bd on which the mac is learnt

intfid

(Optional) Name of the interface for ngoam ping on which dot1q is configured

Command Mode

  • /exec/configure/configngoamconnectcheck

destination-group

[no] destination-group <dgrp-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-group

Create destination group

dgrp-id

Identifier

Command Mode

  • /exec/configure/telemetry

destination-profile

[no] destination-profile <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

Command Mode

  • /exec/configure/callhome

destination-profile

[no] destination-profile

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Specify the default destination profile

Command Mode

  • /exec/configure/telemetry

destination-profile CiscoTAC-1 alert-group

[no] destination-profile CiscoTAC-1 alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC | Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test }

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

alert-group

Add alert group

All

This alert group consists of all of the callhome messages

Cisco-TAC

Events which are meant for Cisco TAC only

Environmental

Power,fan,temperature related events

Inventory

Inventory status events

License

Events related to licensing

Linecard-Hardware

Linecard related events

Supervisor-Hardware

Supervisor related events

Syslog-group-port

Events related to syslog messages filed by port manager

System

Software related events

Test

User generated test events

Configuration

Events related to Configuration

Diagnostic

Events related to Diagnostic

EEM

EEM events

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 email-addr

destination-profile CiscoTAC-1 [ index <i0> ] email-addr <s0>

Syntax Description

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com

index

(Optional) Configure an index(1 to 50) for email-id

i0

(Optional) Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 http

destination-profile CiscoTAC-1 [ index <i0> ] http <s0>

Syntax Description

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

index

(Optional) Configure an index(1 to 50) for http url

i0

(Optional) Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 index email-addr

[no] destination-profile CiscoTAC-1 index <i0> email-addr

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

email-addr

Add email addr

index

Delete email-id associated with index(1 to 50)

i0

Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 index http

[no] destination-profile CiscoTAC-1 index <i0> http

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

http

Add http or https url

index

Delete http url associated with index(1 to 50)

i0

Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 transport-method http

[no] destination-profile CiscoTAC-1 transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

transport-method

Callhome message sending transport-method

http

http transport-method

Command Mode

  • /exec/configure/callhome

destination-profile CiscoTAC-1 transport-method email

[no] destination-profile CiscoTAC-1 transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

transport-method

Callhome message sending transport-method

email

email transport-method

Command Mode

  • /exec/configure/callhome

destination-profile alert-group

[no] destination-profile <s0> alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC | Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test }

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

alert-group

Add alert group

All

This alert group consists of all of the callhome messages

Cisco-TAC

Events which are meant for Cisco TAC only

Environmental

Power,fan,temperature related events

Inventory

Inventory status events

License

Events related to licensing

Linecard-Hardware

Linecard related events

Supervisor-Hardware

Supervisor related events

Syslog-group-port

Events related to syslog messages filed by port manager

System

Software related events

Test

User generated test events

Configuration

Events related to Configuration

Diagnostic

Events related to Diagnostic

EEM

EEM events

Command Mode

  • /exec/configure/callhome

destination-profile email-addr

destination-profile <s0> [ index <i0> ] email-addr <s1>

Syntax Description

destination-profile

Configure destination profiles

s0

User defined destination profile name

email-addr

Add email addr

s1

Provide email address, example: jdow@xyz.com

index

(Optional) Configure an index(1 to 50) for email-id

i0

(Optional) Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile format

destination-profile <s0> format { full-txt | short-txt | XML }

Syntax Description

destination-profile

Configure destination profiles

s0

User defined destination profile name

format

Callhome message format (default XML)

full-txt

Plain text message format

short-txt

Short text message format

XML

XML message format

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination alert-group

[no] destination-profile full-txt-destination alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC | Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test }

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

alert-group

Add alert group

All

This alert group consists of all of the callhome messages

Cisco-TAC

Events which are meant for Cisco TAC only

Environmental

Power,fan,temperature related events

Inventory

Inventory status events

License

Events related to licensing

Linecard-Hardware

Linecard related events

Supervisor-Hardware

Supervisor related events

Syslog-group-port

Events related to syslog messages filed by port manager

System

Software related events

Test

User generated test events

Configuration

Events related to Configuration

Diagnostic

Events related to Diagnostic

EEM

EEM events

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination email-addr

destination-profile full-txt-destination [ index <i0> ] email-addr <s0>

Syntax Description

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com

index

(Optional) Configure an index(1 to 50) for email-id

i0

(Optional) Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination http

destination-profile full-txt-destination [ index <i0> ] http <s0>

Syntax Description

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

index

(Optional) Configure an index(1 to 50) for http url

i0

(Optional) Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination index email-addr

[no] destination-profile full-txt-destination index <i0> email-addr

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

email-addr

Add email addr

index

Delete email-id associated with index(1 to 50)

i0

Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination index http

[no] destination-profile full-txt-destination index <i0> http

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

http

Add http or https url

index

Delete http url associated with index(1 to 50)

i0

Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination message-size

[no] destination-profile full-txt-destination message-size <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

message-size

Configure maximum message size (default 2500000)

i0

Provide maximum possible message size

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination message-level

[no] destination-profile full-txt-destination message-level <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination transport-method email

[no] destination-profile full-txt-destination transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

transport-method

Callhome message sending transport-method

email

email transport-method

Command Mode

  • /exec/configure/callhome

destination-profile full-txt-destination transport-method http

[no] destination-profile full-txt-destination transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

transport-method

Callhome message sending transport-method

http

http transport-method

Command Mode

  • /exec/configure/callhome

destination-profile http

destination-profile <s4> [ index <i0> ] { http <s2> }

Syntax Description

destination-profile

Configure destination profiles

s4

User defined destination profile name

http

Add http or https url

s2

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

index

(Optional) Configure an index(1 to 50) for http url

i0

(Optional) Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile index email-addr

[no] destination-profile <s0> index <i0> email-addr | no destination-profile <s0> email-addr

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

email-addr

Add email addr

index

Delete email-id associated with index(1 to 50)

i0

Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile index http

[no] destination-profile <s4> index <i0> http | no destination-profile <s4> http

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

s4

User defined destination profile name

http

Add http or https url

index

Delete http url associated with index(1 to 50)

i0

Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile message-level

[no] destination-profile <s0> message-level <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode

  • /exec/configure/callhome

destination-profile message-size

[no] destination-profile <s0> message-size <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

message-size

Configure maximum message size (default 2500000)

i0

Provide maximum possible message size

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination alert-group

[no] destination-profile short-txt-destination alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC | Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test }

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

alert-group

Add alert group

All

This alert group consists of all of the callhome messages

Cisco-TAC

Events which are meant for Cisco TAC only

Environmental

Power,fan,temperature related events

Inventory

Inventory status events

License

Events related to licensing

Linecard-Hardware

Linecard related events

Supervisor-Hardware

Supervisor related events

Syslog-group-port

Events related to syslog messages filed by port manager

System

Software related events

Test

User generated test events

Configuration

Events related to Configuration

Diagnostic

Events related to Diagnostic

EEM

EEM events

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination email-addr

destination-profile short-txt-destination [ index <i0> ] email-addr <s0>

Syntax Description

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com

index

(Optional) Configure an index(1 to 50) for email-id

i0

(Optional) Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination http

destination-profile short-txt-destination [ index <i0> ] http <s0>

Syntax Description

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

index

(Optional) Configure an index(1 to 50) for http url

i0

(Optional) Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination index http

[no] destination-profile short-txt-destination index <i0> http

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

http

Add http or https url

index

Delete http url associated with index(1 to 50)

i0

Index between 1 to 50 associate with http url

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination index email-addr

[no] destination-profile short-txt-destination index <i0> email-addr

Syntax Description

no

Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

email-addr

Add email addr

index

Delete email-id associated with index(1 to 50)

i0

Index between 1 to 50 associate with email-id

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination message-size

[no] destination-profile short-txt-destination message-size <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

message-size

Configure maximum message size (default 4000)

i0

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination message-level

[no] destination-profile short-txt-destination message-level <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination transport-method http

[no] destination-profile short-txt-destination transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

transport-method

Callhome message sending transport-method

http

http transport-method

Command Mode

  • /exec/configure/callhome

destination-profile short-txt-destination transport-method email

[no] destination-profile short-txt-destination transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

transport-method

Callhome message sending transport-method

email

email transport-method

Command Mode

  • /exec/configure/callhome

destination-profile transport-method email

[no] destination-profile <s5> transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s5

User defined destination profile name

transport-method

Callhome message sending transport-method

email

email transport-method

Command Mode

  • /exec/configure/callhome

destination-profile transport-method http

[no] destination-profile <s6> transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s6

User defined destination profile name

transport-method

Callhome message sending transport-method

http

http transport-method

Command Mode

  • /exec/configure/callhome

destination-sup interface

[no] destination-sup interface <interface>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-sup

Destination configuration

interface

Configure interfaces

interface

Command Mode

  • /exec/configure/monitor-local-src /exec/configure/config-monitor /exec/configure/config-monitor-erspan-src

destination

{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

(Optional) Optional VRF label

vrf_name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/nfm-exporter

destination

{ [ no ] destination { <ipaddr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf_name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/config-int-exporter

destination

{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

(Optional) Optional VRF label

vrf_name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/config-fte-exporter

destination

{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf-name> | <vrf-known-name> } ] [ v9 ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

(Optional) Optional VRF label

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

v9

(Optional) Send records in V9 format

Command Mode

  • /exec/configure/nfm-exporter

destination

{ [ no ] destination { <ipaddr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf_name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/config-postcard-exporter

destination any

[no] destination any

Syntax Description

no

(Optional) Negate a command or set its defaults

destination

destination address

any

Any destination IP

Command Mode

  • /exec/configure/tunnel-profile

destination group

[no] destination group <group_number>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination

Destination configuration

group

Configure destination group

group_number

Command Mode

  • /exec/configure/monitor-local-dst

destination inband-interface

[no] destination inband-interface

Syntax Description

destination

Destination configuration

inband-interface

Use CPU as the destination

Command Mode

  • /exec/configure/config-ssx-exporter

destination inband-interface

[no] destination inband-interface

Syntax Description

destination

Specify the destination address

inband-interface

Use CPU as the destination

Command Mode

  • /exec/configure/nfm-exporter

destination interface

[no] destination interface <interface_range>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination

Destination configuration

interface

Configure interfaces

interface_range

Command Mode

  • /exec/configure/monitor-local-dst

destination ip

[no] destination ip <ipaddress>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination

Destination configuration

ip

Configure remote IP address

ipaddress

Command Mode

  • /exec/configure/config-monitor-erspan-src

destination ipv4

{ [ no ] destination ipv4 <ipaddr> }

Syntax Description

destination

Destination configuration

ipv4

IP v4 address

ipaddr

IP Address to be configured

Command Mode

  • /exec/configure/config-int-clone-md-sink-collector

destination ipv6

[no] destination ipv6 <ipv6-address>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination

Destination configuration

ipv6

Configure remote IPv6 address

ipv6-address

Command Mode

  • /exec/configure/config-monitor-erspan-src

destination ipv6

{ [ no ] destination { <ipaddr> | ipv6 <ipv6addr> } } [ use-vrf { <vrf-name> | <vrf-known-name> } ]

Syntax Description

destination

Destination configuration

ipaddr

IP Address to be configured

ipv6

IPv6

use-vrf

(Optional) VRF label

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/config-ssx-exporter

destination sup-eth0

{ [ no ] destination sup-eth0 | no destination }

Syntax Description

destination

Specify the collector destination

sup-eth0

Inband to SUP

Command Mode

  • /exec/configure/config-buffer-drop-collector

destination sup-eth0

{ [ no ] destination sup-eth0 | no destination }

Syntax Description

destination

Specify the collector destination

sup-eth0

Inband to SUP

Command Mode

  • /exec/configure/config-buffer-latency-collector

destination sup-eth0

{ [ no ] destination sup-eth0 | no destination }

Syntax Description

destination

Specify the collector destination

sup-eth0

Inband to SUP

Command Mode

  • /exec/configure/config-int-clone-md-sink-collector

device-alias abort

[no] device-alias abort

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

abort

Abort the device-alias configuration

Command Mode

  • /exec/configure

device-alias commit

[no] device-alias commit

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

commit

Commit the device-alias configuration

Command Mode

  • /exec/configure

device-alias confirm-commit enable

[no] device-alias confirm-commit enable

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

confirm-commit

Confirm the commit for device-alias

enable

Enable the confirm-commit mode

Command Mode

  • /exec/configure

device-alias database

[no] device-alias database

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

database

Device-alias database configuration commands

Command Mode

  • /exec/configure

device-alias distribute

[no] device-alias distribute

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

distribute

Enable device-alias configuration distribution

Command Mode

  • /exec/configure

device-alias import fcalias vsan

[no] device-alias import fcalias vsan <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

import

Import configuration

fcalias

Import fcalias definitions

vsan

Import fcalias definitions from the specified VSAN range

i0

VSAN id range

Command Mode

  • /exec/configure

device-alias mode enhanced

[no] device-alias mode enhanced

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

mode

Configure device-alias mode

enhanced

Configure device-alias enhanced mode

Command Mode

  • /exec/configure

device-alias name

[no] device-alias name <s0>

Syntax Description

no

Negate a command or set its defaults

device-alias

Device-alias configuration commands

name

Configure a device-alias

s0

Enter the device-alias

Command Mode

  • /exec/configure/device-alias-db

device-alias name pwwn

device-alias name <s0> pwwn <wwn0> [ force ]

Syntax Description

device-alias

Device-alias configuration commands

name

Configure a device-alias

s0

Enter the device-alias

pwwn

Configure a device-alias for port WWN

wwn0

Enter port WWN

force

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/device-alias-db

device-alias rename

[no] device-alias rename <s0> <s1>

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device-alias configuration commands

rename

Rename a device-alias

s0

Enter the current device-alias name

s1

Enter the new device-alias name

Command Mode

  • /exec/configure/device-alias-db

device-alias vsan

[no] device-alias <s0> vsan <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

device-alias

Device name

s0

Enter device alias name

vsan

VSAN id for device

i0

vsan id

Command Mode

  • /exec/configure/dpvm-db

device-group

{ device-group <name> } | { no device-group <name> }

Syntax Description

no

Negate a command or set its defaults

device-group

ITD device group

name

ITD device group name

Command Mode

  • /exec/configure/itd

device-role

[no] device-role <dev_role>

Syntax Description

no

(Optional) Negate a command or set its defaults

dev_role

Command Mode

  • /exec/configure/config-snoop-policy

device-role

[no] device-role <devrole>

Syntax Description

no

(Optional) Negate a command or set its defaults

devrole

Command Mode

  • /exec/configure/config-dhcp-guard

device-role

[no] device-role <dev_role>

Syntax Description

no

(Optional) Negate a command or set its defaults

dev_role

Command Mode

  • /exec/configure/config-ra-guard

df-election time

df-election time <sec> | no df-election time

Syntax Description

no

Negate a command or set its defaults

df-election

DF election parameters

time

DF election timer

sec

Seconds in decimal format in range 1.0-3.0

Command Mode

  • /exec/configure/config-evpn-msite-bgw

dfe-tuning-delay

{ dfe-tuning-delay <delay-val> | no dfe-tuning-delay [ <delay-val> ] }

Syntax Description

no

Negate a command or set its defaults

dfe-tuning-delay

Configure DFE Tuning delay for interface

delay-val

DFE tuning delay value (ms)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

diagnostic bootup level

diagnostic bootup level { bypass | complete | minimal }

Syntax Description

diagnostic

Diagnostic commands

bootup

Configure Diagnostic for bootup

level

Select diagnostic level

bypass

Skip all bootup test

complete

Complete level

minimal

Minimal level - no MacsecLoopBackTest

Command Mode

  • /exec/configure

diagnostic bootup level

[no] diagnostic bootup level

Syntax Description

no

Negate a command or set its defaults

diagnostic

Diagnostic commands

bootup

Configure Diagnostic for bootup

level

Select diagnostic level

Command Mode

  • /exec/configure

diagnostic clear result module all diagnostic clear result module test

diagnostic clear result module all | diagnostic clear result module <module> test { <test-id> | all }

Syntax Description

diagnostic

Diagnostic commands

clear

Erase Diagnostic Test Results/Stats

result

Diagnostic test result

module

Module keyword

module

Module number

all

Select all

test

Diagnostic test selection

test-id

Command Mode

  • /exec

diagnostic monitor interval module test all hour min second

diagnostic monitor interval module <module> test { all | <name> | <test-id> } hour <hour-cntr> min <min-cntr> second <sec-cntr> | no diagnostic monitor interval module <module> test { all | <name> | <test-id> }

Syntax Description

no

Negate a command or set its defaults

diagnostic

Diagnostic commands

monitor

Configure diagnostic monitoring test

interval

Configure diagnostic monitoring tests interval

module

Module Keyword

module

Module number

test

Diagnostic test selection

all

Select all test ID

test-id

name

Test name

hour

Hour of the day

hour-cntr

Interval in hours

min

Minute of an hour

min-cntr

Interval in minutes

second

Second of a minute

sec-cntr

Interval in seconds

Command Mode

  • /exec/configure

diagnostic monitor module test all

diagnostic monitor module <module> test { all | <name> | <test-id> } | no diagnostic monitor module <module> test { all | <name> | <test-id> }

Syntax Description

no

Negate a command or set its defaults

diagnostic

Diagnostic commands

monitor

Configure diagnostic monitoring test

module

Module Keyword

module

Module number

test

Diagnostic test selection

all

Select all test ID

test-id

name

Test name

Command Mode

  • /exec/configure

diagnostic monitor syslog

[no] diagnostic monitor syslog

Syntax Description

no

(Optional) Negate a command or set its defaults

diagnostic

Diagnostic command

monitor

Configure diagnostic monitoring for syslog

syslog

Diag test failure syslog

Command Mode

  • /exec/configure

diagnostic ondemand action-on-failure continue failure-count diagnostic ondemand action-on-failure stop

diagnostic ondemand action-on-failure continue failure-count <failure-cnt> | diagnostic ondemand action-on-failure stop

Syntax Description

diagnostic

Diagnostic commands

ondemand

On demand diagnostic setting

action-on-failure

Set action to take if test fails

continue

Continue ondemand test until test failure limit is reached

failure-count

Continue failing tests this many times

stop

Stop ondemand tests immediately if a test fails

failure-cnt

Maximum number of test failures allowed

Command Mode

  • /exec

diagnostic ondemand iteration

diagnostic ondemand iteration <iteration-count>

Syntax Description

diagnostic

Diagnostic commands

ondemand

On demand diagnostic setting

iteration

Set number of times to repeat ondemand test list

iteration-count

Number of times to repeat ondemand test list

Command Mode

  • /exec

diagnostic ondemand test-parameter module test port_lb packet-length

diagnostic ondemand test-parameter module <module> test port_lb packet-length <size>

Syntax Description

diagnostic

Diagnostic commands

ondemand

Ondemand command

test-parameter

Set test parameter

module

Module keyword

module

Module number

test

Diagnostic test selection

port_lb

Port loop back test

packet-length

Size of the packet

size

Packet size for the selected module

Command Mode

  • /exec

diagnostic start module test

diagnostic start module <module> test { all | <name> | <test-id> | non-disruptive | per-port } [ port { iall | <port-id> } ]

Syntax Description

diagnostic

Diagnostic commands

start

Starting on demand diagnostic

module

Module keyword

module

Module Number

test

Diagnostic test selection

all

Select all test ID

name

Test name

test-id

non-disruptive

Select the Non-Disruptive test suite [Attribute = N]

per-port

Select the Per-Port test suite [Attribute = P]

port

(Optional) Interface port selection

iall

(Optional) Select all ports

port-id

(Optional)

Command Mode

  • /exec

diagnostic stop module test all

diagnostic stop module <module> test { all | <name> | <test-id> }

Syntax Description

diagnostic

Diagnostic commands

stop

Stopping diagnostic

module

Module keyword

module

Module Number

test

Diagnostic test selection

all

Select all test ID

test-id

name

Test name

Command Mode

  • /exec

diagnostic test simulation module test diagnostic test simulation module test clear

diagnostic test simulation module <module> test <test-id> [ port { <port-id> | all } ] { success | fail | random-fail } | diagnostic test simulation module <module> test <test-id> clear

Syntax Description

diagnostic

Diagnostic commands

test

Diagnostic test selection

simulation

Simulating Diagnostic result

module

Module keyword

module

Module Number

test

Diagnostic test selection

test-id

port

(Optional) Interface port selection

all

(Optional) Select all ports

port-id

(Optional)

success

pass test result

fail

fail test result

random-fail

fail test result randomly

clear

Stop simulation

Command Mode

  • /exec

diff-clean

diff-clean [ all-sessions ]

Syntax Description

diff-clean

remove temp files created by '| diff' filters

all-sessions

(Optional) remove '| diff' temp files from all sessions (past and present!) of current user

Command Mode

  • /exec

diff-clean all-users

diff-clean all-users

Syntax Description

diff-clean

remove temp files created by '| diff' filters

all-users

remove '| diff' temp files from all sessions (past and present!) of all users

Command Mode

  • /exec

diff

| diff [ again | echo | -c [ <lines> ] | -b | -B | -i | -I <regexp> | -y | --left-column | -W <columns> | -q | -s ] +

Syntax Description

|

Pipe command output to filter

diff

show difference between current and previous invocation (creates temp files: remove them with 'diff-clean' command and dont use it on commands with big outputs, like 'show tech'!)

again

(Optional) dont create new file: use old ones, just change display options or add more filters

echo

(Optional) echo the current file (only effective if no old file)

-c

(Optional) set number of lines of context (default 3)

lines

(Optional) number of lines of context

-b

(Optional) Ignore changes in amount of white space

-B

(Optional) Ignore changes that just insert or delete blank lines

-i

(Optional) Ignore changes in case

-I

(Optional) Ignore changes that just insert or delete lines that match regexp

regexp

(Optional) regexp of lines to ignore

-y

(Optional) Use the side by side output format

--left-column

(Optional) Print only the left column of two common lines in side by side format

-W

(Optional) Use an output width of <columns> in side by side format

columns

(Optional) Use an output width of <columns> in side by side format

-q

(Optional) Report only whether the files differ, not the details of the differences

-s

(Optional) Report when two files are the same

Command Mode

  • /output

dir

dir [ <uri0> | <uri1> | <uri2> ] [ __readonly__ { TABLE_dir <fsize> <timestring> <fname> } { <usage> <bytesused> <bytesfree> <bytestotal> } ]

Syntax Description

dir

list files in a directory

uri0

(Optional) Directory or filename

uri1

(Optional) Directory or filename on expansion flash

uri2

(Optional) Directory or filename on log flash

__readonly__

(Optional) Read Only

TABLE_dir

(Optional) show dir

fsize

(Optional) filesize

timestring

(Optional) time string

fname

(Optional) filename

usage

(Optional) usage

bytesused

(Optional) bytes used

bytesfree

(Optional) bytes free

bytestotal

(Optional) bytes total

Command Mode

  • /exec

disable-connected-check

[ no | default ] disable-connected-check

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

disable-connected-check

Disable check for directly connected peer

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

disable-fka

[no] disable-fka

Syntax Description

no

(Optional) Negate a command or set its defaults

disable-fka

Disables verifying FIP Keep Alives

Command Mode

  • /exec/configure/if-vfc

disable-peer-as-check

[ no | default ] disable-peer-as-check

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

disable-peer-as-check

Disable checking of peer AS-number while advertising

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn

disable-policy-batching

[no] disable-policy-batching [ nexthop | { { ipv4 | ipv6 } prefix-list <prfxlist-name> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

disable-policy-batching

Disable batching evaluation of outbound policy for a peer

nexthop

(Optional) batching based on nexthop

ipv4

(Optional) IPv4 address-family

ipv6

(Optional) IPv6 address-family

prefix-list

(Optional) Apply prefix-list

prfxlist-name

(Optional) Name of prefix-list

Command Mode

  • /exec/configure/router-bgp

disable-smart-zoning

[no] disable-smart-zoning

Syntax Description

no

(Optional) Negate a command or set its defaults

disable-smart-zoning

Set to disable smart zoning for the zone

Command Mode

  • /exec/configure/attribute-group

disable vlan

[no] disable { vlan <vlan-range> } [ port <port-range> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

vlan

Disable detection on VLAN

vlan-range

vlan range max span 1024, Example: 2000-3000,400,500

port

(Optional) Disable detection on port

port-range

(Optional) Disable interface for loop detection

disable

Disable port-vlan

Command Mode

  • /exec/configure/configngoamloopdetection

discard-route external

[no] discard-route { external | internal }

Syntax Description

no

(Optional) Negate a command or set its defaults

discard-route

Install discard route

external

External route

internal

Internal route

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

discard-route external

[no] discard-route { external | internal }

Syntax Description

no

(Optional) Negate a command or set its defaults

discard-route

Install discard route

external

External route

internal

Internal route

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

disjoint

[no] disjoint

Syntax Description

no

(Optional) Negate a command or set its defaults

disjoint

Configure disjointness association type

Command Mode

  • /exec/configure/sr/te/pol/cndpaths/pref/constraint/assoc

disjoint

[no] disjoint

Syntax Description

no

(Optional) Negate a command or set its defaults

disjoint

Configure disjointness association type

Command Mode

  • /exec/configure/sr/te/color/cndpaths/pref/constraint/assoc

distance

distance <ebgp-dist> <ibgp-dist> <local-dist> | no distance [ <ebgp-dist> <ibgp-dist> <local-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

Configure administrative distance

ebgp-dist

Distance for EBGP routes

ibgp-dist

Distance for IBGP routes

local-dist

Distance for local routes

Command Mode

  • /exec/configure/router-bgp/router-bgp-af

distance

distance <distance> | no distance [ <distance> ]

Syntax Description

no

Negate a command or set its defaults

distance

RIP administrative distance

distance

RIP administrative distance

Command Mode

  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

Administrative distance

admin-dist

Distance value

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv4 /exec/configure/router-isis/router-isis-af-ipv6

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

OSPFv3 administrative distance

admin-dist

adminitrative distance value

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

distance

{ { distance <int-distance> <ext-distance> } | { no distance [ <int-distance> <ext-distance> ] } }

Syntax Description

no

Negate a command or set its defaults

distance

Define an administrative distance

int-distance

Distance for internal routes

ext-distance

Distance for external routes

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

OSPF administrative distance

admin-dist

adminitrative distance value

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

distribute into route-map all

{ { distribute <src-level> into <dst-level> { { route-map { <map-name> | <rtr_pol_name> } } | all } } | { no distribute <src-level> into <dst-level> [ { route-map { <map-name> | <rtr_pol_name> } } | all ] } }

Syntax Description

no

Negate a command or set its defaults

distribute

Distribute routes between ISIS levels

src-level

Route-distribution between levels

dst-level

Route-distribution between levels

route-map

Route Map to constrain distribution

into

from level-n into level-m

map-name

A 'routing-rules' route-map name

rtr_pol_name

An existing routing-rules policy

all

Distribute all level-n routes

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv4 /exec/configure/router-isis/router-isis-af-ipv6

distribute link-state

[no] distribute link-state [ instance-id <instid> ] [ level <level> ] [ throttle <seconds> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

distribute

Distribute routes between ISIS levels

link-state

Distribute link-state

instance-id

(Optional) Instance ID of ISIS process

instid

(Optional) Instance ID of ISIS process

level

(Optional) Level to be distributed

level

(Optional) IS-IS level

throttle

(Optional) Throttle timer in seconds

seconds

(Optional) Throttle timer in seconds

Command Mode

  • /exec/configure/router-isis

dns

[no] dns { <WORD> } { name-server { <hostname> | <ip-address> } } { [ source-ip { <source-ip-hostname> | <source-ip-address> } ] | [ source-port <src-port> ] } +

Syntax Description

source-ip

(Optional) <source-ip-hostname>

source-port

(Optional) <src-port>

no

(Optional)

dns

DNS Operation

WORD

Target IP Address or Hostname

name-server

Name Server

hostname

Destination hostname, broadcast disallowed

ip-address

Destination IP address, broadcast disallowed

source-ip-hostname

(Optional) source IP hostname, broadcast disallowed

source-ip-address

(Optional) source IP address, broadcast disallowed

src-port

(Optional) Port Number (Recommended port range between 1025-65534)

Command Mode

  • /exec/configure/ip-sla

domain-id

domain-id { <id> | { type <dtype> value <dvalue> } | Null } | no domain-id [ <id> | { type <dtype> value <dvalue> } | Null ]

Syntax Description

no

Negate a command or set its defaults

domain-id

OSPF domain-ID

id

OSPF domain ID in IP address format

type

OSPF domain ID type in Hex format

dtype

OSPF domain ID type in Hex format

value

OSPF domain ID ext. community value in Hex

dvalue

Null

Null Domain-ID

Command Mode

  • /exec/configure/router-ospf/vrf

domain-id secondary

domain-id { <id> | { type <dtype> value <dvalue> } | Null } secondary | no domain-id [ <id> | { type <dtype> value <dvalue> } | Null ] secondary

Syntax Description

no

Negate a command or set its defaults

domain-id

OSPF domain-ID

id

OSPF domain ID in IP address format

type

OSPF domain ID type in Hex format

dtype

OSPF domain ID type in Hex format

value

OSPF domain ID ext. community value in Hex

dvalue

Null

Null Domain-ID

secondary

Secondary Domain-ID

Command Mode

  • /exec/configure/router-ospf/vrf

domain-tag

[no] domain-tag <as-number>

Syntax Description

no

(Optional) Negate a command or set its defaults

domain-tag

Set OSPF process domain-tag

as-number

AS number

Command Mode

  • /exec/configure/router-ospf/vrf

dont-capability-negotiate

[ no | default ] dont-capability-negotiate

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

dont-capability-negotiate

Don't negotiate capability with this neighbor

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

dos2nxos

dos2nxos <uri0>

Syntax Description

dos2nxos

DOS to NXOS text file format converter

uri0

Filename to be displayed

Command Mode

  • /exec

dot1q

{ dot1q <dot1q-id> [ <intf-id> ] } | { no dot1q }

Syntax Description

no

Negate a command or set its defaults

dot1q

Encapsulation dot1q/bd

dot1q-id

Encapsulation dot1q/bd value

intf-id

(Optional) Name of the interface for ngoam on which dot1q is configured

Command Mode

  • /exec/configure/configngoamprofile

dot1q

{ dot1q <vlan-id> [ cos <cos-val> ] } | { no dot1q }

Syntax Description

no

Negate a command or set its defaults

dot1q

specify flow profile to include dot1q tag

vlan-id

specify flow profile vlan-id

cos

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

cos-val

(Optional) class of service value

Command Mode

  • /exec/configure/configngoamprofileflow

dot1q default dynamic

{ dot1q default dynamic } | { no dot1q default }

Syntax Description

no

Negate a command or set its defaults

dynamic

Dynamic Profile Map: Retrieve profile name from the external server

dot1q

Dot1Q Encapsulation

default

Default (wildcard). Match any dot1q when there is no specific dot1q mapping configured

Command Mode

  • /exec/configure/profile-map /exec/configure/profile-map-global

dot1x authentication event server dead action authorize

[no] dot1x authentication event server dead action authorize

Syntax Description

dot1x

dot1x configuration commands

authentication

Dot1x Authentication

event

Event Type

server

Some Server

dead

Server is Unreachable

action

Action Type

authorize

Authorize all clients

Command Mode

  • /exec/configure

dot1x authentication order

[no] dot1x authentication order <auth_order>

Syntax Description

dot1x

dot1x configuration commands

authentication

Authentication type

order

specifying the authentication order

auth_order

Authentication orders

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x default

dot1x default

Syntax Description