S Commands

sak-expiry-time

[no] sak-expiry-time <ts>

Syntax Description

sak-expiry-time

Time in seconds to force SAK rekey

ts

time in seconds

Command Mode

  • /exec/configure/macsec-policy

sak-rekey-time

[no] sak-rekey-time <ts>

Syntax Description

sak-rekey-time

Time in seconds to force SAK rekey

ts

time in seconds

Command Mode

  • /exec/configure/tunenc-policy

sampling-rate prepost

[no] sampling-rate { pre-trigger <pre-sample-rate> } { post-trigger <post-sample-rate> }

Syntax Description

no

(Optional) Negate the command

sampling-rate

Configure sampling-rate parameters

pre-trigger

Pre-trigger parameters

pre-sample-rate

Transactions to be captured out of 16 samples (1-16)

post-trigger

Post-trigger parameters

post-sample-rate

Transactions to be captured out of 16 samples (1-16)

Command Mode

  • /exec/configure/pkt-drop

sampling

sampling <sampling_range> | no sampling

Syntax Description

no

Negate a command or set its defaults

sampling

Set the sampling range for SPAN packets.

sampling_range

Sampling range: N = every Nth packet will be spanned

Command Mode

  • /exec/configure/monitor-local-src /exec/configure/config-monitor /exec/configure/config-monitor-erspan-src

sampling rate

[no] sampling rate <samplingrate>

Syntax Description

sampling

Specify sampling for INT Clone MD

rate

Sampling rate for INT Clone MD

samplingrate

sampling rate: 1 for capture all

Command Mode

  • /exec/configure/config-int-clone-md-source-monitor

sampling rate

[no] sampling { rate <samplingrate> | microburst <mbrate> <mbpackets> }

Syntax Description

sampling

Specify sampling for buffer-latency

rate

Sampling rate for buffer-latency

samplingrate

sampling rate

microburst

Microburst mode for buffer-latency

mbrate

Microburst rate. Actual value will be the nearest lower multiple of 122.

mbpackets

Microburst packets

Command Mode

  • /exec/configure/config-buffer-latency-monitor

sampling rate

[no] sampling { rate <samplingrate> | microburst <mbrate> <mbpackets> }

Syntax Description

sampling

Specify sampling for buffer-drop

rate

Sampling rate for buffer-drop

samplingrate

sampling rate: 10 to 16777215. 1 for capture all

microburst

Microburst mode for buffer-drop

mbrate

Microburst rate. Actual value will be the nearest lower multiple of 122.

mbpackets

Microburst packets

Command Mode

  • /exec/configure/config-buffer-drop-monitor

sap hash-algorithm HMAC-SHA-1

{ [ no ] sap hash-algorithm HMAC-SHA-1 } | { sap hash-algorithm HMAC-MD5 }

Syntax Description

sap

Specify preferred SAP negotiation parameters

hash-algorithm

Hashing Algorithm to use during SAP protocol

HMAC-SHA-1

use HMAC-SHA-1 for hashing (default is HMAC-MD5)

HMAC-MD5

use HMAC-MD5 for hashing

Command Mode

  • /exec/configure/cts-dot1x /exec/configure/cts-manual

sap modelist

[no] sap modelist <mode_opt>

Syntax Description

sap

Specify preferred SAP negotiation parameters

modelist

encryption mode

mode_opt

modelist options

Command Mode

  • /exec/configure/cts-dot1x

sap pmk sap pmk use-dot1x

sap pmk <pmk> [ left-zero-padded ] [ modelist <mode_opt> ] | sap pmk use-dot1x [ modelist <mode_opt> ] | no sap

Syntax Description

sap

Specify preferred SAP negotiation parameters

pmk

pairwise master key

pmk

32 byte value specified as a string

left-zero-padded

(Optional) Pad with zeros on the left if PMK length is less than 32 bytes

modelist

(Optional) encryption mode

mode_opt

(Optional) modelist options

modelist

(Optional) <mode_opt>

use-dot1x

Use pmk generated after dot1x authentication. Use dot1x commands to configure dot1x on this port

Command Mode

  • /exec/configure/cts-manual

save

save <uri0>

Syntax Description

save

Save the current configuration session to uri

uri0

Enter the complete uri where the session is to be stored

Command Mode

  • /exec/configure

save configuration load

{ save configuration | load } <uri0>

Syntax Description

save

Save the current configuration session to uri

load

Load the configuration

configuration

current configuration session

uri0

Enter file name

Command Mode

  • /exec/configure

scale-factor module

[no] scale-factor <sf-value> module <module-number>

Syntax Description

no

(Optional) Negate a command or set its defaults

scale-factor

Scale factor

sf-value

Specify scale factor value from 0.10 to 2.00

module

Module

module-number

specify module number

Command Mode

  • /exec/configure/ctrl-plane

scheduler aaa-authentication

{ scheduler aaa-authentication { password { 0 <s0> | 7 <s1> | <s2> } | username <s3> password { 01 <s4> | 71 <s5> | <s6> } } | no scheduler aaa-authentication { password [ { 0 <s0> | 7 <s1> | <s2> } ] | username <s3> password [ { 01 <s4> | 71 <s5> | <s6> } ] } }

Syntax Description

no

Negate a command or set its defaults

scheduler

Config commands for scheduler

aaa-authentication

Password for AAA authentication(of logged in user)

password

Specify the password of logged in user(for AAA authentication)

0

Password (clear text) of logged in user

s0

password (clear text) of logged in user

7

Encrypted password of logged in user

s1

Encrypted password (for AAA authentication)

s2

Password (clear text) of logged in user

username

logged in user name

s3

user name (for AAA authentication)

password

Specify the password of logged in user(for AAA authentication)

01

Password (clear text) of logged in user

s4

password (clear text) of logged in user

71

Encrypted password of logged in user

s5

Encrypted password (for AAA authentication)

s6

Password (clear text) of logged in user

Command Mode

  • /exec/configure

scheduler job name

[no] scheduler job name <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

scheduler

Config commands for scheduler

job

Define a job

name

Specify a name for the job

s0

Name of the job

Command Mode

  • /exec/configure

scheduler logfile size

{ scheduler logfile size <i0> | no scheduler logfile size [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

scheduler

Config commands for scheduler

logfile

Scheduler log file configuration

size

Specify the log file size

i0

Size of the file in KB

Command Mode

  • /exec/configure

scheduler schedule name

[no] scheduler schedule name <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

scheduler

Config commands for scheduler

schedule

Define a schedule

name

Specify a name for the schedule

s0

Name of the schedule

Command Mode

  • /exec/configure

scheduler transport email

{ scheduler transport email { from <s0> | reply-to <s1> | smtp-server <host0> [ port <i1> ] } | no scheduler transport email { from | reply-to | smtp-server } }

Syntax Description

no

Negate a command or set its defaults

scheduler

Config commands for scheduler

transport

Configure transport related configuration

email

Configure email transport related configuration

from

Configure from email address

s0

Provide from email address, example: SJ-9500-1@xyz.com

reply-to

Configure replyto email address

s1

Provide reply-to email address, example: admin@xyz.com

smtp-server

Configure SMTP server address

host0

SMTP server(DNS name or IPv4 or IPv6 address)

port

(Optional) Configure SMTP server port (default:25)

i1

(Optional) SMTP server port

Command Mode

  • /exec/configure

schema

[no] schema <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

schema

PTP unicast-negotiation schema

s0

Name of schema

Command Mode

  • /exec/configure/ptp-ucast-negotiation

scripting tcl init

scripting tcl init <uri0> | no scripting tcl init

Syntax Description

no

Negate a command or set its defaults

scripting

Configure scripting parameters

tcl

Specify scripting parameter for tcl

init

Specify init parameters

uri0

Tcl init script name

Command Mode

  • /exec

scripting tcl recursion-limit

scripting tcl recursion-limit <limit> | no scripting tcl recursion-limit

Syntax Description

no

Negate a command or set its defaults

scripting

Configure scripting parameters

tcl

Specify scripting parameter for tcl

recursion-limit

Specify recursion-limit

limit

Specify limit

Command Mode

  • /exec

section

| section <pattern>

Syntax Description

|

Pipe command output to filter

section

show lines that include the pattern as well as the subsequent lines that are more indented than matching line

pattern

the pattern (regular expression) to match

Command Mode

  • /output

secure-handoff

{ [ no ] secure-handoff }

Syntax Description

no

(Optional) Negate a command or set its defaults

secure-handoff

Confirm dynamic-eid discovery by probing for remote host

Command Mode

  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

security-level

[no] security-level <seclvl>

Syntax Description

no

(Optional) Negate a command or set its defaults

seclvl

Command Mode

  • /exec/configure/config-snoop-policy

security-policy

[no] security-policy <policy>

Syntax Description

security-policy

Configure Security policy

policy

Security Policy options

Command Mode

  • /exec/configure/macsec-policy

sed

| sed [ -n ] + <expr>

Syntax Description

|

Pipe command output to filter

sed

Stream Editor

-n

(Optional) suppress automatic printing of pattern space

expr

Edition command (script)

Command Mode

  • /output

segment-list name

[no] segment-list name <seg-list-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-list

Explicit segment list configuration

name

Segment-list name

seg-list-name

Identifying name for the segment-list with max 128 characters

Command Mode

  • /exec/configure/sr/te

segment-routing

[no] segment-routing

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-routing

Configure Traffic Engineering Segment Routing related configurations

Command Mode

  • /exec/configure/sr/te

segment-routing

[no] segment-routing

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-routing

Enable Segment Routing

Command Mode

  • /exec/configure

segment-routing mpls

[no] segment-routing mpls

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-routing

Segment routing parameters

mpls

Enable segment routing MPLS

Command Mode

  • /exec/configure/router-ospf

segment-routing mpls

[no] segment-routing mpls

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-routing

Segment-routing properties

mpls

Configure MPLS parameters

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv4

segment-routing srv6

[no] segment-routing srv6

Syntax Description

no

(Optional) Negate a command or set its defaults

srv6

Configure srv6

segment-routing

Configure segment-routing

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4

segment-routing srv6

[no] segment-routing srv6

Syntax Description

no

(Optional) Negate a command or set its defaults

segment-routing

Segment-routing properties

srv6

Configure Segment-Routing for IPv6

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv6

segment-routing srv6

[no] segment-routing srv6

Syntax Description

no

(Optional) Negate a command or set its defaults

srv6

Configure srv6

segment-routing

Configure segment-routing

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6

segment-routing srv6

[no] segment-routing srv6

Syntax Description

no

(Optional) Negate a command or set its defaults

srv6

Configure srv6

segment-routing

Configure segment-routing

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf

segment-routing srv6

[no] segment-routing srv6

Syntax Description

no

(Optional) Negate a command or set its defaults

srv6

Configure srv6

segment-routing

Configure segment-routing

Command Mode

  • /exec/configure/router-bgp

segments

[no] segments

Syntax Description

no

(Optional) Negate a command or set its defaults

segments

Candidate path-option segments

Command Mode

  • /exec/configure/sr/te/pol/cndpaths/pref/constraint

segments

[no] segments

Syntax Description

no

(Optional) Negate a command or set its defaults

segments

Candidate path-option segments

Command Mode

  • /exec/configure/sr/te/color/cndpaths/pref/constraint

selection input

[no] selection input

Syntax Description

no

(Optional) Negate a command or set its defaults

selection

Selection configuration

input

Enable this source for selection

Command Mode

  • /exec/configure/clock-if/fsync

selection input

[no] selection input

Syntax Description

no

(Optional) Negate a command or set its defaults

selection

Selection configuration

input

Enable this source for selection

Command Mode

  • /exec/configure/if-eth-base/fsync

selection input

[no] selection input

Syntax Description

no

(Optional) Negate a command or set its defaults

selection

Selection configuration

input

Enable this source for selection

Command Mode

  • /exec/configure/gnss-if/fsync

send-community

[ no | default ] send-community [ both | extended | standard ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

send-community

Send Community attribute to this neighbor

both

(Optional) Send Standard and Extended Community attributes

extended

(Optional) Send Extended Community attribute

standard

(Optional) Send Standard Community attribute

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls

send-community

[ no | default ] send-community [ both | standard ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

send-community

Send Community attribute to this neighbor

both

(Optional) Send Standard and Extended Community attributes

standard

(Optional) Send Standard Community attribute

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

send-community extended

[ no | default ] send-community extended

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

send-community

Send Community attribute to this neighbor

extended

Send Extended Community attribute

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

send-lifetime smonth_a smonth_b smonth_c smonth_d smonth_e smonth_f smonth_g smonth_h smonth_i smonth_j smonth_k smonth_l duration infinite emonth_a emonth_b emonth_c emonth_d emonth_e emonth_f emonth_g emonth_h emonth_i emonth_j emonth_k emonth_l

{ { send-lifetime [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } } | { no send-lifetime [ [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } ] } }

Syntax Description

no

Negate a command or set its defaults

send-lifetime

Set send lifetime of macsec key

local

(Optional) Specify time in local timezone

stime

HH:MM:SS Time to start <0-23>:<0-59>:<0-59>

etime

HH:MM:SS Time to end <0-23>:<0-59>:<0-59>

smonth_a

smonth_b

smonth_c

smonth_d

smonth_e

smonth_f

smonth_g

smonth_h

smonth_i

smonth_j

smonth_k

smonth_l

emonth_a

emonth_b

emonth_c

emonth_d

emonth_e

emonth_f

emonth_g

emonth_h

emonth_i

emonth_j

emonth_k

emonth_l

sday

Day of the month to start

eday

Day of the month to end

syear

Year to start

eyear

Year to end

duration

Set key lifetime duration

dsec

Duration in seconds

infinite

Never Expires

Command Mode

  • /exec/configure/macseckeychain-key

send-lifetime smonth_a smonth_b smonth_c smonth_d smonth_e smonth_f smonth_g smonth_h smonth_i smonth_j smonth_k smonth_l duration infinite emonth_a emonth_b emonth_c emonth_d emonth_e emonth_f emonth_g emonth_h emonth_i emonth_j emonth_k emonth_l

{ { send-lifetime [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } } | { no send-lifetime [ [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } ] } }

Syntax Description

no

Negate a command or set its defaults

send-lifetime

Set send lifetime of key

local

(Optional) Specify time in local timezone

stime

HH:MM:SS Time to start <0-23>:<0-59>:<0-59>

etime

HH:MM:SS Time to end <0-23>:<0-59>:<0-59>

smonth_a

smonth_b

smonth_c

smonth_d

smonth_e

smonth_f

smonth_g

smonth_h

smonth_i

smonth_j

smonth_k

smonth_l

emonth_a

emonth_b

emonth_c

emonth_d

emonth_e

emonth_f

emonth_g

emonth_h

emonth_i

emonth_j

emonth_k

emonth_l

sday

Day of the month to start

eday

Day of the month to end

syear

Year to start

eyear

Year to end

duration

Set key lifetime duration

dsec

Duration in seconds

infinite

Never Expires

Command Mode

  • /exec/configure/keychain-key

send-lifetime smonth_a smonth_b smonth_c smonth_d smonth_e smonth_f smonth_g smonth_h smonth_i smonth_j smonth_k smonth_l duration infinite emonth_a emonth_b emonth_c emonth_d emonth_e emonth_f emonth_g emonth_h emonth_i emonth_j emonth_k emonth_l

{ { send-lifetime [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } } | { no send-lifetime [ [ local ] <stime> { smonth_a | smonth_b | smonth_c | smonth_d | smonth_e | smonth_f | smonth_g | smonth_h | smonth_i | smonth_j | smonth_k | smonth_l } <sday> <syear> { duration <dsec> | infinite | <etime> { emonth_a | emonth_b | emonth_c | emonth_d | emonth_e | emonth_f | emonth_g | emonth_h | emonth_i | emonth_j | emonth_k | emonth_l } <eday> <eyear> } ] } }

Syntax Description

no

Negate a command or set its defaults

send-lifetime

Set send lifetime of tunnel encryption key

local

(Optional) Specify time in local timezone

stime

HH:MM:SS Time to start <0-23>:<0-59>:<0-59>

etime

HH:MM:SS Time to end <0-23>:<0-59>:<0-59>

smonth_a

smonth_b

smonth_c

smonth_d

smonth_e

smonth_f

smonth_g

smonth_h

smonth_i

smonth_j

smonth_k

smonth_l

emonth_a

emonth_b

emonth_c

emonth_d

emonth_e

emonth_f

emonth_g

emonth_h

emonth_i

emonth_j

emonth_k

emonth_l

sday

Day of the month to start

eday

Day of the month to end

syear

Year to start

eyear

Year to end

duration

Set key lifetime duration

dsec

Duration in seconds

infinite

Never Expires

Command Mode

  • /exec/configure/tunnelencryptkeychain-key

send

send <line>

Syntax Description

send

Send message to open sessions

line

Send message (a line) to all open sessions

Command Mode

  • /exec

send session

send session <s0> <line>

Syntax Description

send

Send message to open sessions

session

Send message to specific session

s0

Specify pts/tty device type

line

Enter a one line message

Command Mode

  • /exec

sender

[no] sender

Syntax Description

no

(Optional) Negate a command or set its defaults

sender

Policies for a Sender

Command Mode

  • /exec/configure/nbm-host-policy

sender

[no] sender

Syntax Description

no

(Optional) Negate a command or set its defaults

sender

Policies for a Sender

Command Mode

  • /exec/configure/nbm-vrf/nbm-host-policy

sensor-group

[no] sensor-group <sgrp-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

sensor-group

Create a sensor group

sgrp-id

Identifier

Command Mode

  • /exec/configure/telemetry

sequence

{ [ no ] sequence <seq> | no sequence }

Syntax Description

sequence

Sequence Number

seq

Differentiated services codepoint value

Command Mode

  • /exec/configure/config-postcard-exporter

sequence

{ [ no ] sequence <seq> | no sequence }

Syntax Description

sequence

Sequence Number

seq

Sequence Number value

Command Mode

  • /exec/configure/config-int-exporter

server-key 0 7

{ { [ no ] server-key { 0 <s0> | 7 <s1> | <s2> } } | { no server-key } }

Syntax Description

no

(Optional) Negate a command or set its defaults

server-key

Encryption key shared with the radius clients

0

RADIUS shared secret(clear text)

s0

RADIUS shared secret(clear text)

7

RADIUS shared secret(encrypted)

s1

RADIUS shared secret(encrypted)

s2

RADIUS shared secret(clear text)(Max Size 63)

Command Mode

  • /exec/configure/locsvr-da-radius

server

[no] server { <hostipname> }

Syntax Description

no

(Optional) Negate a command or set its defaults

server

TACACS+ server name or IP address

hostipname

IPV4/IPV6 address or DNS name

Command Mode

  • /exec/configure/tacacs+

server

[no] server <host0>

Syntax Description

no

(Optional) Negate a command or set its defaults

server

LDAP server name

host0

LDAP server name

Command Mode

  • /exec/configure/ldap

server

[no] server <hostipname>

Syntax Description

no

(Optional) Negate a command or set its defaults

server

RADIUS server name or IP address

hostipname

IPV4/IPV6 address or DNS name

Command Mode

  • /exec/configure/radius

server protocol ldap

[no] server protocol ldap { ipv6 <ipv6addr> | ip <ipaddr> | host <hostname> } [ port <portnum> ] [ vrf { <vrf-name> | <vrf-known-name> } ] [ enable-ssl ]

Syntax Description

no

(Optional) Negate a command or set its defaults

server

Configure database server

protocol

Configure database protocol

ldap

Use LDAP

ipv6

IPv6 address of server

ip

IP address of server

ipaddr

Enter IP address of server

host

Hostname of server

hostname

Enter hostname of server

port

(Optional) Port

portnum

(Optional) Enter port number

vrf

(Optional) vrf context

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

enable-ssl

(Optional) LDAP server enable ssl

Command Mode

  • /exec/configure/fabric-db

server protocol radius group

[no] server protocol radius group <groupname>

Syntax Description

no

(Optional) Negate a command or set its defaults

server

Configure database server

protocol

Configure database protocol

radius

Use RADIUS

group

AAA group

groupname

Enter AAA group name of servers

Command Mode

  • /exec/configure/fabric-db

server protocol xmpp ip

[no] server protocol xmpp { ip <ipaddr> | host <hostname> } [ port <portnum> ] [ vrf { <vrf-name> | <vrf-known-name> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

server

Configure database server

protocol

Configure database protocol

xmpp

Use XMPP

ip

IP address of server

ipaddr

Enter IP address of server

host

Hostname of server

hostname

Enter hostname of server

port

(Optional) Port

portnum

(Optional) Enter port number

vrf

(Optional) vrf context

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec/configure/fabric-db

service-end-point ip

[no] service-end-point { { ip <ip-addr> } | { ipv6 <ipv6-addr> } } [ interface <interface> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

service-end-point

Details of service-end-point instance

ip

IPv4 address of service node

ipv6

IPv6 address of service node

interface

(Optional) Interface through which service is connected

ip-addr

IPv4 address in format i.i.i.i

interface

(Optional) Interface

Command Mode

  • /exec/configure/epbr/svc

service-end-point ip

[no] service-end-point { { ip <ip-addr> } | { ipv6 <ipv6-addr> } } [ interface <interface> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

service-end-point

Details of service-end-point instance

ip

IPv4 address of service node

ipv6

IPv6 address of service node

interface

(Optional) Interface through which service is connected

ip-addr

IPv4 address in format i.i.i.i

interface

(Optional) Interface

Command Mode

  • /exec/configure/epbr-sess/svc

service-interface

[no] service-interface <interface>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-interface

Interface through which all end-points of service are connected

interface

Interface

Command Mode

  • /exec/configure/epbr/svc

service-name

[no] service-name <nxsdk-service-name> [ profile { <nxsdk-profile-name> | <profile-name> } ]

Syntax Description

service-name

Complete path and name of file to execute

nxsdk-service-name

Service name

profile

(Optional) Service profile

nxsdk-profile-name

(Optional) Name of the profile

profile-name

(Optional) Name of the profile

Command Mode

  • /exec/configure/nxsdk-remote

service-policy-dynamic input

[no] service-policy-dynamic input <policy_name>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy-dynamic

Attach a policy to control-plane interface

input

Input the policy name

policy_name

Name of the policy

Command Mode

  • /exec/configure/ctrl-plane-dyn

service-policy

[no] service-policy [ type qos ] <pmap-name-qos>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Configure hierarchial policy-map

type

(Optional) Specify the type of this policy

qos

(Optional) Qos policy

pmap-name-qos

Policy-map name

Command Mode

  • /exec/configure/policy-map/class

service-policy

[no] service-policy [ type qos ] <inp-or-out> <pmap-name-qos> [ no-stats ]

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Configure service policy for an interface

type

(Optional) Specify the type of this policy

qos

(Optional) Qos policy

inp-or-out

pmap-name-qos

Policy-map name __nil__ You must create a policy-map before using this command

no-stats

(Optional) Disable statistics for this policy

Command Mode

  • /exec/configure/if-set-qos /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch /exec/configure/if-fc /exec/configure/if-san-port-channel /exec/configure/if-nve

service-policy input

[no] service-policy input <policy_name>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Attach a policy to control-plane interface

input

Input the policy name

policy_name

Name of the policy

Command Mode

  • /exec/configure/ctrl-plane

service-policy type network-qos

[no] service-policy type network-qos <pmap-name-nq>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Policy Map

type

Specify the type of this policy-map

network-qos

Network QoS policy

pmap-name-nq

Policy-map name

Command Mode

  • /exec/configure/system/qos

service-policy type qos

[no] service-policy type qos <inp-only> <pmap-name-qos>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Policy Map

type

Specify the type of this policy-map

qos

System-level QoS policy

inp-only

pmap-name-qos

Policy-map name __nil__ You must create a policy-map before using this command

Command Mode

  • /exec/configure/system/qos

service-policy type queuing

[no] service-policy type queuing <inp-or-out> <pmap-name-que>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Policy Map

type

Specify the type of this policy-map

queuing

DCE Queuing policy

inp-or-out

pmap-name-que

Policy-map name

Command Mode

  • /exec/configure/system/qos

service-policy type queuing

[no] service-policy type queuing <inp-or-out> <pmap-name-que> [ no-stats ]

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Configure service policy for an interface

type

Specify the type of this policy

queuing

Queuing policy

inp-or-out

pmap-name-que

Policy-map name

no-stats

(Optional) Disable statistics for this policy

Command Mode

  • /exec/configure/if-set-que

service-policy type queuing

[no] service-policy type queuing <pmap-name-que>

Syntax Description

no

(Optional) Negate a command or set its defaults

service-policy

Set the inner policy-map

type

Specify the type of this policy

queuing

Queuing policy

pmap-name-que

Policy-map name __nil__ You must create a policy-map before using this command

Command Mode

  • /exec/configure/policy-map/type/queuing/class

service exclude-bootconfig

{ service exclude-bootconfig | no service exclude-bootconfig }

Syntax Description

no

Negate a command or set its defaults

service

Configure boot variables

exclude-bootconfig

exclude bootvar config from asciigen

Command Mode

  • /exec/configure

service password-recovery

[no] service password-recovery

Syntax Description

no

(Optional) Negate a command or set its defaults

service

Service

password-recovery

Configure password-recovery option of console

Command Mode

  • /exec/configure

service unsupported-transceiver

[no] service unsupported-transceiver

Syntax Description

no

(Optional) Negate a command or set its defaults

service

Serviceability Commands

unsupported-transceiver

Configure support for transceivers not supported by Cisco

Command Mode

  • /exec/configure

session-limit

[no] session-limit <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

session-limit

Set the max no of concurrent vsh sessions

i0

Max concurrent vsh sessions

Command Mode

  • /exec/configure/line

session domain-lookup

session domain-lookup | no session domain-lookup

Syntax Description

session

Configure session preferences

no

Negate a command or set its defaults

domain-lookup

Session

Command Mode

  • /exec

session protection

[no] session protection [ vrf { <vrf-name> | <vrf-known-name> } ] [ for <pfx-list> ] [ duration { <secs> | infinite } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

session

Configure session parameters

protection

Configure session protection parameters

vrf

(Optional) VRF Routing/Forwarding instance information

vrf-name

(Optional) VPN Routing/Forwarding instance name

vrf-known-name

(Optional) Known VRF name

for

(Optional) Prefix list to specify LDP peers

pfx-list

(Optional) Prefix list for LDP peers

duration

(Optional) Period to sustain session protection after loss of link discovery

secs

(Optional) Holdup time in seconds

infinite

(Optional) Protect session forever after loss of link discovery

Command Mode

  • /exec/configure/ldp

set-attached-bit

[no] set-attached-bit

Syntax Description

no

(Optional) Negate a command or set its defaults

set-attached-bit

Configure L1|L2 router to set/unset attached bit in its L1 LSP

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv6

set-overload-bit

[no] set-overload-bit | [ no ] set-overload-bit { always | on-startup { <secs> | [ <seconds> ] wait-for bgp <as> } } [ suppress { [ interlevel ] [ external ] } ]

Syntax Description

no

Negate a command or set its defaults

set-overload-bit

Signal other routers not to use us for transit

always

Set the overload bit unconditionally

on-startup

Set the overload bit on IS-IS startup

secs

Clear the overload bit after an elapsed time in seconds

wait-for

Clear the overload bit when notified by a specific protocol

bgp

Border Gateway Protocol (BGP)

seconds

(Optional) Clear the overload bit after an elapsed time in seconds

as

Autonomous system number

suppress

(Optional) Suppress route redistribution if overload bit set

interlevel

(Optional) Suppress interlevel route redistribution

external

(Optional) Suppress external route redistribution

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

set-overload-bit

{ no set-overload-bit | [ no ] set-overload-bit { always | on-startup { <secs> | <seconds> } } }

Syntax Description

no

Negate a command or set its defaults

set-overload-bit

Signal other routers not to use us for transit

always

Set the overload bit unconditionally

on-startup

Set the overload bit on IS-IS startup

secs

Clear the overload bit after an elapsed time in seconds

seconds

Clear the overload bit after an elapsed time in seconds

Command Mode

  • /exec/configure/l2mp-isis/l2mp-isis-vrf-common

set

[no] set { load-sharing per-packet }

Syntax Description

set

Set attribute

load-sharing

Load sharing across ECMP by set out-of-order bit

per-packet

per MiM packet

no

(Optional) Negate a command or set its defaults

Command Mode

  • /exec/configure/policy-map/class

set

[no] set { { cos [ inner ] <cos-val> } | { dscp [ tunnel ] { <dscp-val> | <opt_set_dscp> } } | { precedence [ tunnel1 ] { <prec-val> | <opt_set_prec> } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

cos

IEEE 802.1Q class of service

inner

(Optional) Set inner 802.1Q class of service in QinQ environment

cos-val

802.1Q Class of Service value

dscp

DSCP in IP(v4) and IPv6 packets

tunnel

(Optional) Set DSCP in tunnel encapsulation

dscp-val

DSCP value

opt_set_dscp

precedence

Precedence in IP(v4) and IPv6 packets

tunnel1

(Optional) Set DSCP in tunnel encapsulation

prec-val

IP Precedence value

opt_set_prec

Command Mode

  • /exec/configure/pmap/class

set

set <paramname> <paramval>

Syntax Description

set

Set the parameter value

paramname

Enter the name of the parameter

paramval

Enter the parameter value

Command Mode

  • /exec/configure/param-inst

set

[no] set { { dlb-disable } | { precedence [ prec-tunnel ] { <prec-val> | <prec-enum> } } | { dscp [ tunnel ] { <dscp-val> | <dscp-enum> } } | { cos <cos-val> } | { qos-group <qos-grp-val> } | { mpls experimental { { topmost <exp-value> } | { imposition <exp-value-imp> } } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

dlb-disable

Disable Dynamic Load Balancing

precedence

Precedence in IP(v4) and IPv6 packets

prec-tunnel

(Optional) Set Precedence in tunnel encapsulation

prec-val

IP Precedence value

prec-enum

dscp

DSCP in IP(v4) and IPv6 packets

tunnel

(Optional) Set DSCP in tunnel encapsulation

dscp-val

DSCP value

dscp-enum

cos

IEEE 802.1Q Class of Service

cos-val

802.1Q Class of Service value

qos-group

Qos-group

qos-grp-val

mpls

Set MPLS label

experimental

Set MPLS experimental label

topmost

Set MPLS topmost label

imposition

Push the label and set new one on top

exp-value

MPLS value

exp-value-imp

MPLS value

Command Mode

  • /exec/configure/policy-map/class

set

[no] set { { discard-class <dis-class-val> } | { { { cos1 cos2 } | { dscp1 dscp2 } | { prec1 prec2 } | { dis-class1 dis-class2 } | { dscp3 mpls-exp-imposition } | { mpls-exp-topmost dscp4 } | { mpls-exp-topmost1 mpls-exp-topmost2 } } table <table-map-name> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

cos1

IEEE 802.1Q class of service

cos2

IEEE 802.1Q class of service

dscp1

DSCP in IP(v4) and IPv6 packets

dscp2

DSCP in IP(v4) and IPv6 packets

prec1

Precedence in IP(v4) and IPv6 packets

prec2

Precedence in IP(v4) and IPv6 packets

discard-class

Discard class

dis-class1

Discard class

dis-class2

Discard class

dis-class-val

Discard class value

table

Table defining mapping from input to output

table-map-name

Table-map name

dscp3

DSCP in IP(v4) and IPv6 packets

mpls-exp-imposition

mpls-exp-imposition

mpls-exp-topmost

mpls-exp-topmost

dscp4

DSCP in IP(v4) and IPv6 packets

mpls-exp-topmost1

mpls-exp-topmost

mpls-exp-topmost2

mpls-exp-topmost

Command Mode

  • /exec/configure/policy-map/class

set

[no] set { { cos <cos-val> } | { eth-src-mac-addr <src-mac-addr> } | { eth-dest-mac-addr <dest-mac-addr> } | { vlan <vlan-number> } | { ip-tos <ip-tos-value> <ip-tos-mask> } | { out-interface <iface-list> } | { dscp [ tunnel ] { <dscp-val> | <dscp-enum> } } | { precedence [ prec-tunnel ] { <prec-val> | <prec-enum> } } | { discard-class <dis-class-val> } | { qos-group <qos-grp-val> } | { { { cos1 cos2 } | { dscp1 dscp2 } | { prec1 prec2 } | { dis-class1 dis-class2 } | { dscp3 mpls-exp-imposition } | { mpls-exp-topmost dscp4 } | { mpls-exp-topmost1 mpls-exp-topmost2 } } } | { mpls experimental { { topmost <exp-value> } | { imposition <exp-value-imp> } } } | action-strip-vlan | action-drop-pkt | divert-action | copy-action | action-decrement-ttl | forward-normal | goto-pmap <pmap-table-handle> }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

cos

IEEE 802.1Q class of service

cos1

IEEE 802.1Q class of service

cos2

IEEE 802.1Q class of service

cos-val

802.1Q Class of Service value

eth-dest-mac-addr

Action on Layer 2 destination MAC address

eth-src-mac-addr

Action on Layer 2 source MAC address

src-mac-addr

Layer 2 MAC Address

dest-mac-addr

Layer 2 MAC Address

vlan

Set the VLAN ID

vlan-number

VLAN NUMBER

ip-tos

Set the IPv4 TOS

ip-tos-value

IPv4 TOS Value

ip-tos-mask

IPV4 TOS Mask

out-interface

Output to a Specified Interface

iface-list

Physical Interface Name and Number or List

action-strip-vlan

Perform the action STRIP-VLAN-ID

action-drop-pkt

Perform the action Drop the Packet

divert-action

Divert the packets to Controller

copy-action

Copy the packets to Controller

action-decrement-ttl

Decrement TTL on the Packet

forward-normal

Forward the packets normally

goto-pmap

Goto pmap/table

pmap-table-handle

Pmap-table handle

dscp

DSCP in IP(v4) and IPv6 packets

dscp1

DSCP in IP(v4) and IPv6 packets

dscp2

DSCP in IP(v4) and IPv6 packets

tunnel

(Optional) Set DSCP in tunnel encapsulation

dscp-val

DSCP value

dscp-enum

precedence

Precedence in IP(v4) and IPv6 packets

prec1

Precedence in IP(v4) and IPv6 packets

prec2

Precedence in IP(v4) and IPv6 packets

prec-tunnel

(Optional) Set Precedence in tunnel encapsulation

prec-val

IP Precedence value

prec-enum

discard-class

Discard class

dis-class1

Discard class

dis-class2

Discard class

dis-class-val

Discard class value

qos-group

Qos-group

qos-grp-val

Qos-group value

mpls

Set MPLS label

experimental

Set MPLS experimental label

topmost

Set MPLS topmost label

imposition

Push the label and set new one on top

exp-value

MPLS value

exp-value-imp

MPLS value

dscp3

DSCP in IP(v4) and IPv6 packets

mpls-exp-imposition

mpls-exp-imposition

mpls-exp-topmost

mpls-exp-topmost

dscp4

DSCP in IP(v4) and IPv6 packets

mpls-exp-topmost1

mpls-exp-topmost

mpls-exp-topmost2

mpls-exp-topmost

Command Mode

  • /exec/configure/policy-map/type/plc/class

set as-path none remote-as local-as

{ set as-path { none | { <asn> | remote-as | local-as } + } } | { no set as-path { none | { <asn> | remote-as | local-as } + } }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

as-path

for a BGP AS-path manipulation attribute

none

Set Empty AS-path

asn

<AA4> where AA4 is either <1-4294967295> or <1-65535>[.<0-65535>] format

remote-as

set aspath with remote-as

local-as

set aspath with local-as

Command Mode

  • /exec/configure/route-map

set as-path prepend last-as tag

{ set as-path { prepend { last-as <lastas> | <as> + } | tag } } | { no set as-path { prepend [ last-as [ <lastas> ] | <as> + ] | tag } }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

as-path

Prepend string for a BGP AS-path attribute

prepend

Prepend to the AS-Path

last-as

Prepend last AS to the as-path

lastas

number of last-AS prepends

as

AS number

tag

Set the tag as an AS-path attribute

as

(Optional)

Command Mode

  • /exec/configure/route-map

set as-path replace private-as

{ set as-path replace [ <asn> + ] { <asn_trail> | private-as } [ with { <r_asn> | remote-as | none } ] } | { no set as-path replace }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

as-path

Prepend string for a BGP AS-path attribute

replace

Replace the AS-path attribute

asn

(Optional) <AA4>, where AA4 is either <1-4294967295> or <1-65535>[.<0-65535>] format

asn_trail

<AA4>, where AA4 is either <1-4294967295> or <1-65535>[.<0-65535>] format

private-as

Replace private-as range

with

(Optional) replace with remote-as or asn

r_asn

(Optional) AS number

remote-as

(Optional) replace asn with remote-as

none

(Optional) remove the matched asn

Command Mode

  • /exec/configure/route-map

set comm-list delete

{ { set comm-list <name> delete } | { no set comm-list } }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

comm-list

set BGP community list (for deletion)

name

Community list name

delete

Delete matching communities

Command Mode

  • /exec/configure/route-map

set cos

[no] set cos <cos-val>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

cos

IEEE 802.1Q class of service

cos-val

802.1Q Class of Service value

Command Mode

  • /exec/configure/policy-map/type/uf/class

set cos

[no] set cos <cos-val>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

cos

IEEE 802.1Q Class of Service

cos-val

802.1Q Class of Service value

Command Mode

  • /exec/configure/policy-map/type/queuing/class

set dampening

{ set dampening <halflife> <reuse> <supress> <duration> } | { no set dampening [ <halflife> <reuse> <supress> <duration> ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

dampening

Set BGP route flap dampening parameters

halflife

half-life time for the penalty

reuse

penalty to start reusing a route

supress

penalty to start suppressing a route

duration

Maximum duration to suppress a stable route

Command Mode

  • /exec/configure/route-map

set distance

{ set distance <external-dist> [ <internal-dist> [ <local-dist> ] ] } | { no set distance }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

distance

Set the Administrative distance of route

external-dist

Administrative distance for IGP or EBGP routes

internal-dist

(Optional) Administrative distance for internal routes

local-dist

(Optional) Administrative distance for local routes

Command Mode

  • /exec/configure/route-map

set evpn gateway-ip

set evpn gateway-ip { <addr> | use-nexthop } | no set evpn gateway-ip [ <addr> | use-nexthop ]

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

evpn

Set BGP EVPN Routes

gateway-ip

Set gateway IP for type 5 EVPN routes

use-nexthop

Use nexthop address as gateway IP

addr

Gateway IP address

Command Mode

  • /exec/configure/route-map

set extcomm-list delete

{ { set extcomm-list <name> delete } | { no set extcomm-list [ <name> delete ] } }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcomm-list

set BGP extcommunity list (for deletion)

name

Extended Community list name

delete

Delete matching extcommunities

Command Mode

  • /exec/configure/route-map

set extcommunity 4byteas-generic transitive additive

{ set extcommunity 4byteas-generic { { transitive <ext-comm-gen-trans> | non-transitive <ext-comm-gen-nontrans> } + [ additive ] | additive | none } } | { no set extcommunity 4byteas-generic [ { transitive <ext-comm-gen-trans> | non-transitive <ext-comm-gen-nontrans> } + [ additive ] | additive | none ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcommunity

Set BGP extcommunity attribute

4byteas-generic

Generic extended community

additive

(Optional) Add to existing generic extcommunity

none

No extcommunity generic attribute

transitive

Transitive extended community

non-transitive

Non-Transitive extended community

ext-comm-gen-trans

Extcommunity number aa4:nn format

ext-comm-gen-nontrans

Extcommunity number aa4:nn format

ext-comm-gen-trans

(Optional) <ext-comm-gen-nontrans>

Command Mode

  • /exec/configure/route-map

set extcommunity color

{ set extcommunity color <color-value> } | { no set extcommunity color [ <color-value> ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcommunity

Set BGP extcommunity attribute

color

Color Extended Community

color-value

Color Community value

Command Mode

  • /exec/configure/route-map

set extcommunity cost

{ set extcommunity cost { [ igp | pre-bestpath ] <comm-id> <cost-value> } + } | { no set extcommunity cost [ [ igp | pre-bestpath ] <comm-id> <cost-value> ] + }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcommunity

Set BGP extcommunity attribute

cost

Cost

igp

(Optional) Compare following IGP cost comparison

pre-bestpath

(Optional) Compare before all other steps in bestpath calculation

comm-id

Community ID

cost-value

Cost Community value

comm-id

(Optional) <cost-value>

Command Mode

  • /exec/configure/route-map

set extcommunity evpn rmac

{ set extcommunity evpn rmac <mac-addr> } | { no set extcommunity evpn rmac <mac-addr> }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcommunity

Set BGP extcommunity attribute

evpn

EVPN Extended Community

rmac

Router MAC

mac-addr

MAC address

Command Mode

  • /exec/configure/route-map

set extcommunity rt additive

{ set extcommunity rt { { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } + [ additive ] | additive } } | { no set extcommunity rt [ { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } + [ additive ] | additive ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

extcommunity

Set BGP extcommunity attribute

rt

Route-Target

additive

(Optional) Add to existing rt extcommunity

ext-comm-rt-aa2nn4

Extcommunity number

ext-comm-rt-aa4nn2

Extcommunity number

ext-comm-rt-aa2nn4

(Optional) <ext-comm-rt-aa4nn2>

Command Mode

  • /exec/configure/route-map

set forwarding-address

[no] set forwarding-address

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

forwarding-address

Set the forwarding address

Command Mode

  • /exec/configure/route-map

set inner ipv4

set { inner | outer } ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

outer

Mask and Match By Outer Packet Fields

ipv4

IPv4 Fields

l3-type

(Optional) L3 Packet Type

l3_type

(Optional) L3 Packet Type

pyld-len

(Optional) Payload Length

pyld_len

(Optional) Payload Length

v6-vld

(Optional) IPv6 Valid Information

v6_vld

(Optional) IPv6 Valid Information

version

(Optional) Version

ver

(Optional) Version

header-len

(Optional) Header Length

hlen

(Optional) Header Length

dscp

(Optional) Diff. Serv. Code Point

dscp_val

(Optional) Diff. Serv. Code Point

ecn

(Optional) Explicit Congestion Ntfn

ecn_val

(Optional) Explicit Congestion Ntfn

packet-len

(Optional) Packet Total Length

pkt_len

(Optional) Packet Total Length

more-frags

(Optional) More Fragments Available

mf

(Optional) More Fragments Available

fragment-off

(Optional) Fragments Offset

fragoff

(Optional) Fragments Offset

ttl

(Optional) Time to Live

ttl_val

(Optional) Time to Live

next-protocol

(Optional) Next(L4) Protocol

nproto

(Optional) Next(L4) Protocol

checksum

(Optional) Checksum

csum

(Optional) Checksum

src_ip

(Optional) Source IP Address

sip

(Optional) Source IP Address

dst_ip

(Optional) Destination IP Address

dip

(Optional) Destination IP Address

Command Mode

  • /exec/elamns/sel6

set inner ipv4

set inner ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

ipv4

IPv4 Fields

l3-type

(Optional) L3 Packet Type

l3_type

(Optional) L3 Packet Type

pyld-len

(Optional) Payload Length

pyld_len

(Optional) Payload Length

v6-vld

(Optional) IPv6 Valid Information

v6_vld

(Optional) IPv6 Valid Information

version

(Optional) Version

ver

(Optional) Version

header-len

(Optional) Header Length

hlen

(Optional) Header Length

dscp

(Optional) Diff. Serv. Code Point

dscp_val

(Optional) Diff. Serv. Code Point

ecn

(Optional) Explicit Congestion Ntfn

ecn_val

(Optional) Explicit Congestion Ntfn

packet-len

(Optional) Packet Total Length

pkt_len

(Optional) Packet Total Length

more-frags

(Optional) More Fragments Available

mf

(Optional) More Fragments Available

fragment-off

(Optional) Fragments Offset

fragoff

(Optional) Fragments Offset

ttl

(Optional) Time to Live

ttl_val

(Optional) Time to Live

next-protocol

(Optional) Next(L4) Protocol

nproto

(Optional) Next(L4) Protocol

checksum

(Optional) Checksum

csum

(Optional) Checksum

src_ip

(Optional) Source IP Address

sip

(Optional) Source IP Address

dst_ip

(Optional) Destination IP Address

dip

(Optional) Destination IP Address

Command Mode

  • /exec/elamns/sel4

set inner l2

set { inner | outer } l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos <cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> | vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

outer

Mask and Match By Outer Packet Fields

l2

All Layer 2 Fields

snap_vld

(Optional) SNAP Header Information Valid

snap_vld

(Optional) SNAP Header Information Valid

cntag_vld

(Optional) CNTag Information Valid

cntag_vld

(Optional) CNTag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

vlan

(Optional) VLAN Id (Present only in case of FEX)

vlan_id

(Optional) VLAN Id

cos

(Optional) Class of Service

cos_val

(Optional) Class of Service Type

cfi

(Optional) CFI Setting

cfi_vld

(Optional) CFI Setting Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_svif

(Optional) VNTAG Source vif

vntag_svif

(Optional) VNTAG Source vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_looped

(Optional) VNTAG Header Looped Valid

vntag_loop

(Optional) VNTAG Header Looped Valid

vntag_pointer

(Optional) VNTAG Header Pointer Valid

vntag_p

(Optional) VNTAG Header Pointer Valid

src_mac

(Optional) Source MAC Address

smac

(Optional) Source MAC Address Value

dst_mac

(Optional) Destination MAC Address

dmac

(Optional) Destination MAC Address Value

Command Mode

  • /exec/elamns/sel5

set inner l2

set inner l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos <cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> | vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

l2

All Layer 2 Fields

snap_vld

(Optional) SNAP Header Information Valid

snap_vld

(Optional) SNAP Header Information Valid

cntag_vld

(Optional) CNTag Information Valid

cntag_vld

(Optional) CNTag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

vlan

(Optional) VLAN Id (Present only in case of FEX)

vlan_id

(Optional) VLAN Id

cos

(Optional) Class of Service

cos_val

(Optional) Class of Service Type

cfi

(Optional) CFI Setting

cfi_vld

(Optional) CFI Setting Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_svif

(Optional) VNTAG Source vif

vntag_svif

(Optional) VNTAG Source vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_looped

(Optional) VNTAG Header Looped Valid

vntag_loop

(Optional) VNTAG Header Looped Valid

vntag_pointer

(Optional) VNTAG Header Pointer Valid

vntag_p

(Optional) VNTAG Header Pointer Valid

src_mac

(Optional) Source MAC Address

smac

(Optional) Source MAC Address Value

dst_mac

(Optional) Destination MAC Address

dmac

(Optional) Destination MAC Address Value

Command Mode

  • /exec/elamns/sel4

set inner l2 hg2

set { inner | outer } l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror> | hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid> | hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast <hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

outer

Mask and Match By Outer Packet Fields

l2

All Layer 2 Fields

hg2

High Gig2 Fields

hg2_vid

(Optional) High Gig2 VLAN Tag

hg2_vlan

(Optional) High Gig2 VLAN Tag Information

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_dstpid

(Optional) High Gig2 Destination Port ID

hg2_dpid

(Optional) High Gig2 Destination Port ID

hg2_dstmod

(Optional) High Gig2 Destination Module ID

hg2_dmod

(Optional) High Gig2 Destination Module ID

hg2_srcpid

(Optional) High Gig2 Source Port ID

hg2_spid

(Optional) High Gig2 Source Port ID

hg2_srcmod

(Optional) High Gig2 Souce Module ID

hg2_smod

(Optional) High Gig2 Souce Module ID

hg2_l3vld

(Optional) High Gig2 Packet L3 Switched

hg2_l3_vld

(Optional) High Gig2 Packet L3 Switched

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_mcast

(Optional) High Gig2 MultiCast Forwarding Information

hg2_mcast_vld

(Optional) High Gig2 Multicast Forwarding Information

hg2-vld

(Optional) High Gig2 Valid Information

hg2_vld

(Optional) High Gig2 Valid Information

hg2-cos

(Optional) High Gig2 CoS Information

hg2_cos

(Optional) High Gig2 CoS Information

Command Mode

  • /exec/elamns/sel5

set inner l2 hg2

set inner l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror> | hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid> | hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast <hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

l2

All Layer 2 Fields

hg2

High Gig2 Fields

hg2_vid

(Optional) High Gig2 VLAN Tag

hg2_vlan

(Optional) High Gig2 VLAN Tag Information

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_dstpid

(Optional) High Gig2 Destination Port ID

hg2_dpid

(Optional) High Gig2 Destination Port ID

hg2_dstmod

(Optional) High Gig2 Destination Module ID

hg2_dmod

(Optional) High Gig2 Destination Module ID

hg2_srcpid

(Optional) High Gig2 Source Port ID

hg2_spid

(Optional) High Gig2 Source Port ID

hg2_srcmod

(Optional) High Gig2 Souce Module ID

hg2_smod

(Optional) High Gig2 Souce Module ID

hg2_l3vld

(Optional) High Gig2 Packet L3 Switched

hg2_l3_vld

(Optional) High Gig2 Packet L3 Switched

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_mcast

(Optional) High Gig2 MultiCast Forwarding Information

hg2_mcast_vld

(Optional) High Gig2 Multicast Forwarding Information

hg2-vld

(Optional) High Gig2 Valid Information

hg2_vld

(Optional) High Gig2 Valid Information

hg2-cos

(Optional) High Gig2 CoS Information

hg2_cos

(Optional) High Gig2 CoS Information

Command Mode

  • /exec/elamns/sel4

set inner l4

set { inner | outer } l4 [ { src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum> | flags <flag_val> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

outer

Mask and Match By Outer Packet Fields

l4

L4 Fields

src-port

(Optional) Source Port Information

sport

(Optional) Source Port

dst-port

(Optional) Destination Port Information

dport

(Optional) Destination Port

packet-len

(Optional) Packet Length

pkt_len

(Optional) Packet Length

checksum

(Optional) Checksum

csum

(Optional) Checksum

flags

(Optional) L4 Flags

flag_val

(Optional) L4 Flags

Command Mode

  • /exec/elamns/sel7

set inner l4

set inner l4 [ { src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum> | flags <flag_val> } ] +

Syntax Description

set

Setup Trigger

inner

Mask and Match By Inner Packet Fields

l4

L4 Fields

src-port

(Optional) Source Port Information

sport

(Optional) Source Port

dst-port

(Optional) Destination Port Information

dport

(Optional) Destination Port

packet-len

(Optional) Packet Length

pkt_len

(Optional) Packet Length

checksum

(Optional) Checksum

csum

(Optional) Checksum

flags

(Optional) L4 Flags

flag_val

(Optional) L4 Flags

Command Mode

  • /exec/elamns/sel4

set interface

[no] set interface <iface>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

interface

Output interface

iface

Interface name

Command Mode

  • /exec/configure/route-map

set interval find-new-host

[no] set interval find-new-host <val>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set vmtracker options

interval

Set the polling interval

find-new-host

Set interval for the new host searching timer

val

The host search interval value in seconds (0 to disable)

Command Mode

  • /exec/configure/vmt-conn

set interval sync-full-info

[no] set interval sync-full-info <val>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set vmtracker options

interval

Set the polling interval

sync-full-info

Set interval for syncing complete info from host

val

The sync info interval value in seconds (0 to disable)

Command Mode

  • /exec/configure/vmt-conn

set ip address prefix-list

[no] set ip address prefix-list <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

address

Specify IP address

prefix-list

IP prefix-list

name

Name of prefix list

Command Mode

  • /exec/configure/route-map

set ip default next-hop

[no] set ip default next-hop [ recursive ] { load-share | <addr1> + [ load-share ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

recursive

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

default

Set default next-hop

next-hop

Next hop address

addr1

IP address of next hop

load-share

Enables load sharing

Command Mode

  • /exec/configure/route-map

set ip default next-hop verify-availability

[no] set ip default next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

default

Set default next-hop

next-hop

Next hop address

verify-availability

Verify the reachability of the tracked object

addr

IP address of next hop

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

Command Mode

  • /exec/configure/route-map

set ip next-hop

[no] set ip next-hop { <addr1> srte-policy { name <name-value> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

addr1

IP address of next hop

srte-policy

Set SR-TE Policy details

name

Name of the SR-TE Policy

name-value

Name of the SR-TE Policy

Command Mode

  • /exec/configure/route-map

set ip next-hop

[no] set ip next-hop [ recursive ] { [ <addr1> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

recursive

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

next-hop

Next hop address

addr1

(Optional) IP address of next hop

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set ip next-hop

[no] set ip next-hop { <addr1> srte-policy { color <color-value> [ endpoint <endpoint-value> ] } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

addr1

IP address of next hop

srte-policy

Set SR-TE Policy details

color

Color of the SR-TE Policy

endpoint

(Optional) Endpoint of the SR-TE Policy

color-value

Policy Color

endpoint-value

(Optional) IPv4 endpoint address

Command Mode

  • /exec/configure/route-map

set ip next-hop peer-address

[no] set ip next-hop peer-address

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

peer-address

Use peer address (for BGP only)

Command Mode

  • /exec/configure/route-map

set ip next-hop redist-unchanged

[no] set ip next-hop redist-unchanged

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

redist-unchanged

Use unchanged address during redistribution (for BGP session only)

Command Mode

  • /exec/configure/route-map

set ip next-hop unchanged

[no] set ip next-hop unchanged

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

unchanged

Use unchanged address (for eBGP session only)

Command Mode

  • /exec/configure/route-map

set ip next-hop verify-availability

[no] set ip next-hop verify-availability { [ <addr1> [ track <object_id> ] ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

next-hop

Next hop address

verify-availability

Verify the reachability of the tracked object

addr1

(Optional) IP address of next hop

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set ip precedence

{ set ip precedence { <value> | <name> } } | { no set ip precedence [ <value> | <name> ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

precedence

Set precedence field

value

Precedence value

name

Precedence value

Command Mode

  • /exec/configure/route-map

set ip vrf next-hop

[no] set ip vrf { <vrf-name> | <vrf-known-name> } next-hop [ recursive ] { [ <addr1> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

vrf

Use VRF

recursive

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

next-hop

Next hop address

addr1

(Optional) IP address of next hop

vrf-name

VRF name

vrf-known-name

Known VRF name

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set ip vrf next-hop verify-availability

[no] set ip vrf { <vrf-name> | <vrf-known-name> } next-hop verify-availability { [ <addr1> [ track <object_id> ] ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ip

Configure IP features

vrf

Use VRF

next-hop

Next hop address

verify-availability

Verify the reachability of the tracked object

vrf-name

VRF name

vrf-known-name

Known VRF name

addr1

(Optional) IP address of next hop

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set ipv6 address prefix-list

[no] set ipv6 address prefix-list <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

address

Specify IP address

prefix-list

IPv6 prefix-list

name

Name of prefix list

Command Mode

  • /exec/configure/route-map

set ipv6 default next-hop

[no] set ipv6 default next-hop [ recursive ] { load-share | <addr1> + [ load-share ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

recursive

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

default

Set default next-hop

next-hop

Next hop address

load-share

Enables load sharing

addr1

Command Mode

  • /exec/configure/route-map

set ipv6 default next-hop verify-availability

[no] set ipv6 default next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

default

Set default next-hop

verify-availability

Verify the reachability of the tracked object

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop

[no] set ipv6 next-hop { [ <addr> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop ipv6 address

load-share

(Optional) Enables load sharing

force-order

(Optional) Enables Next-hop ordering as per cli

drop-on-fail

(Optional) Drop packets when next-hop unreachable

addr

(Optional)

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop

[no] set ipv6 next-hop { <addr1> srte-policy { name <name-value> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

srte-policy

Set SR-TE Policy details

name

Name of the SR-TE Policy

name-value

Name of the SR-TE Policy

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop

[no] set ipv6 next-hop { <addr1> srte-policy { color <color-value> [ endpoint <endpoint-value> ] } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

srte-policy

Set SR-TE Policy details

color

Color of the SR-TE Policy

endpoint

(Optional) Endpoint of the SR-TE Policy

color-value

Policy Color

endpoint-value

(Optional) IPv4 endpoint address

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop peer-address

[no] set ipv6 next-hop peer-address

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

peer-address

Use peer address (for BGP only)

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop redist-unchanged

[no] set ipv6 next-hop redist-unchanged

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

redist-unchanged

Use unchanged address during redistribution (for BGP session only)

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop unchanged

[no] set ipv6 next-hop unchanged

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

unchanged

Use unchanged address (for eBGP session only)

Command Mode

  • /exec/configure/route-map

set ipv6 next-hop verify-availability

[no] set ipv6 next-hop verify-availability { [ <addr1> [ track <object_id> ] ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

next-hop

Next hop address

verify-availability

Verify the reachability of the tracked object

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set ipv6 precedence

{ set ipv6 precedence { <value> | <name> } } | { no set ipv6 precedence [ <value> | <name> ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

precedence

Set precedence field

value

Precedence value

name

Precedence value

Command Mode

  • /exec/configure/route-map

set ipv6 vrf next-hop

[no] set ipv6 vrf { <vrf-name> | <vrf-known-name> } next-hop { [ <addr> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

vrf

Use VRF

next-hop

Next hop ipv6 address

vrf-name

VRF name

vrf-known-name

Known VRF name

load-share

(Optional) Enables load sharing

force-order

(Optional) Enables Next-hop ordering as per cli

drop-on-fail

(Optional) Drop packets when next-hop unreachable

addr

(Optional)

Command Mode

  • /exec/configure/route-map

set ipv6 vrf next-hop verify-availability

[no] set ipv6 vrf { <vrf-name> | <vrf-known-name> } next-hop verify-availability { [ <addr1> [ track <object_id> ] ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail ] } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

ipv6

Configure IPv6 features

vrf

Use VRF

next-hop

Next hop address

verify-availability

Verify the reachability of the tracked object

vrf-name

VRF name

vrf-known-name

Known VRF name

track

(Optional) The tracking method is track

object_id

(Optional) Object number that the tracking subsystem is tracking

load-share

(Optional) Enables load sharing

force-order

(Optional) Maintains next-hop order as per cli config

drop-on-fail

(Optional) Drop packets when next-hop unreachable

Command Mode

  • /exec/configure/route-map

set label-index

{ { set label-index <value> } | { no set label-index [ <value> ] } }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

label-index

Set Segment Routing (SR) label index of route

value

Segment Routing (SR) label index

Command Mode

  • /exec/configure/route-map

set level level-1 level-1-2 level-2

{ set level { level-1 | level-1-2 | level-2 } } | { no set level [ level-1 | level-1-2 | level-2 ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

level

Where to import route

level-1

Import into a level-1 area

level-1-2

Import into level-1 and level-2

level-2

Import into level-2 sub-domain

Command Mode

  • /exec/configure/route-map

set local-preference

{ set local-preference <pref> | no set local-preference [ <pref> ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

local-preference

BGP local preference path attribute

pref

Preference value

Command Mode

  • /exec/configure/route-map

set metric

{ set metric <metric0> [ <metric1> <metric2> <metric3> <metric4> ] } | { no set metric [ <metric0> [ <metric1> <metric2> <metric3> <metric4> ] ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

metric

Set metric for destination routing protocol

metric0

[+/-] Metric value or Bandwidth in Kbits per second

metric1

(Optional) IGRP delay metric

metric2

(Optional) IGRP reliability metric where 255 is 100% reliable

metric3

(Optional) IGRP Effective bandwidth metric (Loading) 255 is 100%

metric4

(Optional) IGRP MTU of the path

Command Mode

  • /exec/configure/route-map

set mpls-exp-topmost cos table exp-cos-map

[no] set mpls-exp-topmost cos table exp-cos-map

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set attribute

mpls-exp-topmost

MPLS experimental topmost

cos

IEEE 802.1Q Class of Service

table

Table map

exp-cos-map

Exp to cos table map name (reserved)

Command Mode

  • /exec/configure/policy-map/type/queuing/class

set nssa-only

[no] set nssa-only

Syntax Description

no

(Optional) Negate a command or set its defaults

set

Set values in destination routing protocol

nssa-only

OSPF NSSA Areas

Command Mode

  • /exec/configure/route-map

set origin egp igp incomplete

{ set origin { egp | igp | incomplete } } | { no set origin [ { egp | igp | incomplete } ] }

Syntax Description

no

Negate a command or set its defaults

set

Set values in destination routing protocol

origin

BGP origin code

egp

remote EGP

igp

local IGP

incomplete

unknown heritage

Command Mode

  • /exec/configure/route-map

set outer ipv4

set outer ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +

Syntax Description

set

Setup Trigger

outer

Mask and Match By Outer Packet Fields

ipv4

IPv4 Fields

l3-type

(Optional) L3 Packet Type

l3_type

(Optional) L3 Packet Type

pyld-len

(Optional) Payload Length

pyld_len

(Optional) Payload Length

v6-vld

(Optional) IPv6 Valid Information

v6_vld

(Optional) IPv6 Valid Information

version

(Optional) Version

ver

(Optional) Version

header-len

(Optional) Header Length

hlen

(Optional) Header Length

dscp

(Optional) Diff. Serv. Code Point

dscp_val

(Optional) Diff. Serv. Code Point

ecn

(Optional) Explicit Congestion Ntfn

ecn_val

(Optional) Explicit Congestion Ntfn

packet-len

(Optional) Packet Total Length

pkt_len

(Optional) Packet Total Length

more-frags

(Optional) More Fragments Available

mf

(Optional) More Fragments Available

fragment-off

(Optional) Fragments Offset

fragoff

(Optional) Fragments Offset

ttl

(Optional) Time to Live

ttl_val

(Optional) Time to Live

next-protocol

(Optional) Next(L4) Protocol

nproto

(Optional) Next(L4) Protocol

checksum

(Optional) Checksum

csum

(Optional) Checksum

src_ip

(Optional) Source IP Address

sip

(Optional) Source IP Address

dst_ip

(Optional) Destination IP Address

dip

(Optional) Destination IP Address

Command Mode

  • /exec/elamns/sel3

set outer l2

set outer l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos <cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> | vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +

Syntax Description

set

Setup Trigger

outer

Mask and Match By Outer Packet Fields

l2

All Layer 2 Fields

snap_vld

(Optional) SNAP Header Information Valid

snap_vld

(Optional) SNAP Header Information Valid

cntag_vld

(Optional) CNTag Information Valid

cntag_vld

(Optional) CNTag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

qtag_vld

(Optional) VLAN Tag Information Valid

vlan

(Optional) VLAN Id (Present only in case of FEX)

vlan_id

(Optional) VLAN Id

cos

(Optional) Class of Service

cos_val

(Optional) Class of Service Type

cfi

(Optional) CFI Setting

cfi_vld

(Optional) CFI Setting Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_vld

(Optional) VNTAG Information Valid

vntag_svif

(Optional) VNTAG Source vif

vntag_svif

(Optional) VNTAG Source vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_dvif

(Optional) VNTAG Destination vif

vntag_looped

(Optional) VNTAG Header Looped Valid

vntag_loop

(Optional) VNTAG Header Looped Valid

vntag_pointer

(Optional) VNTAG Header Pointer Valid

vntag_p

(Optional) VNTAG Header Pointer Valid

src_mac

(Optional) Source MAC Address

smac

(Optional) Source MAC Address Value

dst_mac

(Optional) Destination MAC Address

dmac

(Optional) Destination MAC Address Value

Command Mode

  • /exec/elamns/sel3

set outer l2 hg2

set outer l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror> | hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid> | hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast <hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +

Syntax Description

set

Setup Trigger

outer

Mask and Match By Outer Packet Fields

l2

All Layer 2 Fields

hg2

High Gig2 Fields

hg2_vid

(Optional) High Gig2 VLAN Tag

hg2_vlan

(Optional) High Gig2 VLAN Tag Information

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_ppd_type

(Optional) High Gig2 Packet Processing Descriptor

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_mirror

(Optional) High Gig2 Packet Mirror Information

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_opcode

(Optional) High Gig2 Packet Type

hg2_dstpid

(Optional) High Gig2 Destination Port ID

hg2_dpid

(Optional) High Gig2 Destination Port ID

hg2_dstmod

(Optional) High Gig2 Destination Module ID

hg2_dmod

(Optional) High Gig2 Destination Module ID

hg2_srcpid

(Optional) High Gig2 Source Port ID

hg2_spid

(Optional) High Gig2 Source Port ID

hg2_srcmod

(Optional) High Gig2 Souce Module ID

hg2_smod

(Optional) High Gig2 Souce Module ID

hg2_l3vld

(Optional) High Gig2 Packet L3 Switched

hg2_l3_vld

(Optional) High Gig2 Packet L3 Switched

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_tc

(Optional) High Gig2 Packet Traffic Class

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_dp

(Optional) High Gig2 Drop Precedence

hg2_mcast

(Optional) High Gig2 MultiCast Forwarding Information

hg2_mcast_vld

(Optional) High Gig2 Multicast Forwarding Information

hg2-vld

(Optional) High Gig2 Valid Information

hg2_vld

(Optional) High Gig2 Valid Information

hg2-cos

(Optional) High Gig2 CoS Information

hg2_cos

(Optional) High Gig2 CoS Information

Command Mode