W Commands

wait-igp-convergence

[no] wait-igp-convergence

Syntax Description

no

(Optional) Negate a command or set its defaults

wait-igp-convergence

Delay initial bestpath until redistributed IGPs have converged

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

wait-to-restore

[no] wait-to-restore <minutes>

Syntax Description

no

(Optional) Negate a command or set its defaults

wait-to-restore

Set the wait-to-restore time

minutes

value in minutes, default 5

Command Mode

  • /exec/configure/if-eth-base/fsync

wait-to-restore

[no] wait-to-restore <minutes>

Syntax Description

no

(Optional) Negate a command or set its defaults

wait-to-restore

Set the wait-to-restore time

minutes

value in minutes, default 5

Command Mode

  • /exec/configure/clock-if/fsync

wait-to-restore

[no] wait-to-restore <minutes>

Syntax Description

no

(Optional) Negate a command or set its defaults

wait-to-restore

Set the wait-to-restore time

minutes

value in minutes, default 5

Command Mode

  • /exec/configure/gnss-if/fsync

watch

watch [ differences ] [ interval <time> ] <watch_cmd>

Syntax Description

watch

execute a program periodically

differences

(Optional) highlight the differences

interval

(Optional) watch interval

time

(Optional) interval in seconds

watch_cmd

enter the command you want to watch

Command Mode

  • /exec

watch service action apply-acl

[no] watch service <service-name> action apply-acl <acl-name> | no watch service

Syntax Description

no

(Optional) Negate a command or set its defaults

watch

Watch a pod/service

service

The pod or service to watch

service-name

Name of the service/pod to watch

action

Action to be applied

apply-acl

Change ACL config

acl-name

Name of the acl to apply

Command Mode

  • /exec/configure/kubernetes

watchlist

[no] watchlist <watchlistname>

Syntax Description

watchlist

Specify POSTCARD watchlist to use

watchlistname

Name of watchlist

Command Mode

  • /exec/configure/config-postcard-monitor

watchlist

[no] watchlist <watchlistname>

Syntax Description

watchlist

Specify INT watchlist to use

watchlistname

Name of watchlist

Command Mode

  • /exec/configure/config-int-monitor

wc

| wc [ -c | -l | -w ]

Syntax Description

|

Pipe command output to filter

wc

Count words, lines, characters

-c

(Optional) Output character count

-l

(Optional) Output line count

-w

(Optional) Output word count

Command Mode

  • /output

wedge bmc ip-addr

[no] wedge bmc ip-addr { <ip> | <ip_v6> }

Syntax Description

no

(Optional) Negate a command or set its defaults

wedge

Configure wedge Board Management controller ip address

bmc

Board Management Controller ip address

ip-addr

BMC ip address

ip

ip adddress

Command Mode

  • /exec/configure

weight

{ weight <weight> } | { { no | default } weight [ <weight> ] }

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

weight

Set default weight for routes from this neighbor

weight

Default weight

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

weight

[no] weight <weight-value>

Syntax Description

no

(Optional) Negate a command or set its defaults

weight

weight for traffic distribution

weight-value

weight value

Command Mode

  • /exec/configure/itd-session-dg-node

weight

[no] weight <weight-value>

Syntax Description

no

(Optional) Negate a command or set its defaults

weight

weight for traffic distribution

weight-value

weight value

Command Mode

  • /exec/configure/itd-dg-node

where

where

Syntax Description

where

shows the cli context you are in

Command Mode

  • /global

where detail

where detail

Syntax Description

where

shows the cli context you are in

detail

shows each entry on separate line

Command Mode

  • /global

window-size

[no] window-size <size>

Syntax Description

window-size

Configure Window size

size

window size value

Command Mode

  • /exec/configure/macsec-policy

window-size

[no] window-size <size>

Syntax Description

window-size

Configure Window size

size

window size value, in num of IP packets

Command Mode

  • /exec/configure/tunenc-policy

wred-queue qos-group-map queue-only

[no] wred-queue qos-group-map queue-only { <qid> }

Syntax Description

no

(Optional) Negate the command

wred-queue

Enable queue based ECN marking for specific qos-group

queue-only

Enable queue based ECN marking

qos-group-map

Qid value

qid

Provide qos-group value

Command Mode

  • /exec/configure

write erase

write erase

Syntax Description

write

Write current configuration

erase

Destroys the configuration on persistent media

Command Mode

  • /exec

Usage Guidelines

You can erase the configuration on your device to return to the configuration defaults. In this context, configuration refers to the startup configuration as displayed by the show startup command. No other internal application or process states are cleared. To remove all application persistency files such as patch rpms, third party rpms, and application configuration in the /etc directory other than configuration, use the install reset command.

write erase boot

write erase boot

Syntax Description

write

Write current configuration

erase

Destroys the configuration on persistent media

boot

Destroys boot configuration on persistent media

Command Mode

  • /exec

write erase debug

write erase debug

Syntax Description

write

Write current configuration

erase

Destroys the configuration on persistent media

debug

Destroys debug configuration on persistent media

Command Mode

  • /exec

write erase poap

write erase poap

Syntax Description

write

Write current configuration

erase

Destroys the configuration on persistent media

poap

Removes System-wide POAP disable configuration on persistent media

Command Mode

  • /exec

wrr-queue qos-group-map

[no] wrr-queue qos-group-map <qid> { <cos> } +

Syntax Description

no

(Optional) Negate the command

wrr-queue

Map traffic priority (QG) values to L3 Multicast Queues

qos-group-map

Qid value

qid

Provide qid value

cos

Provide qos-group-map value

Command Mode

  • /exec/configure

wrr unicast-bandwidth

[no] wrr unicast-bandwidth <bw>

Syntax Description

no

(Optional) Negate the command

wrr

Configure Unicast Traffic Bandwidth Percentage

unicast-bandwidth

Specify rate as percentage of interface data-rate

bw

Value in percentage (Default is set to 50)

Command Mode

  • /exec/configure

wwn oui

wwn oui <oui-id> | no

Syntax Description

oui

{

no

Negate a command or set its defaults

wwn

Set OUI, secondary base MAC addr and range for additional WWNs

oui-id

Enter the oui-id

Command Mode

  • /exec/configure

wwn vsan vsan-wwn

wwn vsan <i0> vsan-wwn <wwn1> | no

Syntax Description

vsan

<i0>

no

Negate a command or set its defaults

wwn

Set secondary base MAC addr and range for additional WWNs

i0

Enter the vsan id

vsan-wwn

vsan-wwn for vsan in interop mode 4

wwn1

Enter wwn for vsan in interop mode 4

Command Mode

  • /exec/configure