B Commands

backoff

backoff <initial-backoff> <maximum-backoff> | no backoff

Syntax Description

no

Negate a command or set its defaults

backoff

Set LDP session backoff parameters

initial-backoff

Initial session backoff time (seconds)

maximum-backoff

Maximum session backoff time (seconds)

Command Mode

  • /exec/configure/ldp

bandwidth

bandwidth { <bandwidth_val> | inherit [ <inherit_val> ] } | no bandwidth { [ <bandwidth_val> ] | inherit [ <inherit_val> ] }

Syntax Description

no

Negate a command or set its defaults

bandwidth

Set bandwidth informational parameter

bandwidth_val

Bandwidth in kilobits

inherit

Specify that bandwidth is inherited

inherit_val

(Optional) Bandwidth in kilobits

Command Mode

  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-ethernet-p2p /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-remote-ethernet-sub

bandwidth

bandwidth <bandwidth_val> | no bandwidth

Syntax Description

no

Negate a command or set its defaults

bandwidth

Set bandwidth informational parameter

bandwidth_val

Bandwidth in kilobits

Command Mode

  • /exec/configure/if-any-tunnel

bandwidth

[no] bandwidth { { xxx <bw-value> [ bps | kbps | mbps | gbps ] | percent <percentage> } | { remaining percent <rem-perc> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

bandwidth

Specify bandwidth for the class

xxx

xxx

bps

(Optional) Bits per second

kbps

(Optional) Kilo bits per second

mbps

(Optional) Mega bits per second

gbps

(Optional) Giga bits per second

percent

Percentage of available bandwidth

percentage

Value in percentage

remaining

% of remaining bandwidth

rem-perc

Value in percentage

Command Mode

  • /exec/configure/policy-map/type/queuing/class

bandwidth

bandwidth <bandwidth_val> | no bandwidth

Syntax Description

no

Negate a command or set its defaults

bandwidth

Set bandwidth informational parameter

bandwidth_val

Bandwidth in kilobits

Command Mode

  • /exec/configure/if-vlan-common

bandwidth

bandwidth { <bandwidth_val> | inherit [ <inherit_val> ] } | no bandwidth { [ <bandwidth_val> ] | inherit [ <inherit_val> ] }

Syntax Description

no

Negate a command or set its defaults

bandwidth

Set bandwidth informational parameter

inherit

Specify that bandwidth is inherited

Command Mode

  • /exec/configure/if-eth-port-channel /exec/configure/if-port-channel-range /exec/configure/if-port-channel-sub /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel-p2p

bandwidth

[no] bandwidth { { <bw-value> [ bps | kbps | mbps | gbps ] | percent <percentage> } | { remaining percent <rem-perc> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

bandwidth

Specify bandwidth for the class

bps

(Optional) Bits per second

kbps

(Optional) Kilo bits per second

mbps

(Optional) Mega bits per second

gbps

(Optional) Giga bits per second

percent

Percentage of available bandwidth

percentage

Value in percentage

remaining

% of remaining bandwidth

rem-perc

Value in percentage

Command Mode

  • /exec/configure/policy-map/type/plc/class

bandwidth kbps mbps gbps

{ { bandwidth { <val_kbps> kbps | <val_mbps> mbps | <val_gbps> gbps } } | { dscp <dscp_val> } } | { no { bandwidth | dscp } }

Syntax Description

no

Negate a command or set its defaults

bandwidth

Bandwidth per flow

val_kbps

Per Flow Bandwidth in Kbps

kbps

Bandwidth value in Kbps

val_mbps

Per Flow Bandwidth in Mbps

mbps

Bandwidth value in Mbps

val_gbps

Per Flow Bandwidth in Gbps

gbps

Bandwidth value in Gbps

dscp

DSCP per flow

dscp_val

Per Flow DSCP

Command Mode

  • /exec/configure/nbm-vrf/nbm-flow-policy/attr

bandwidth kbps mbps gbps

{ { bandwidth { <val_kbps> kbps | <val_mbps> mbps | <val_gbps> gbps } } | { dscp <dscp_val> } } | { no { bandwidth | dscp } }

Syntax Description

no

Negate a command or set its defaults

bandwidth

Bandwidth per flow

val_kbps

Per Flow Bandwidth in Kbps

kbps

Bandwidth value in Kbps

val_mbps

Per Flow Bandwidth in Mbps

mbps

Bandwidth value in Mbps

val_gbps

Per Flow Bandwidth in Gbps

gbps

Bandwidth value in Gbps

dscp

DSCP per flow

dscp_val

Per Flow DSCP

Command Mode

  • /exec/configure/nbm-flow-policy/attr

banner exec

{ banner exec <lineNo> } | { no banner exec }

Syntax Description

no

Negate a command or set its defaults

banner

Configure banner message

exec

Configure banner exec message

lineNo

Delimiter char (first char is delimiter char) followed by message ending with delimiter

Command Mode

  • /exec/configure

banner motd

{ banner motd <line> } | { no banner motd }

Syntax Description

no

Negate a command or set its defaults

banner

Configure banner message

motd

Configure banner motd message

line

Delimiter char (Very first char is delimiter char) followed by message ending with delimiter

Command Mode

  • /exec/configure

bcm-shell module

bcm-shell module <module>

Syntax Description

bcm-shell

bcm shell/cmd

module

Module number of the linecard

module

Enter module number

Command Mode

  • /exec

bcm-shell module

bcm-shell module <module> <quoted-cmd>

Syntax Description

bcm-shell

bcm shell/cmd

module

Module number of the linecard

module

Enter module number

quoted-cmd

the command to run on bcm-shell

Command Mode

  • /exec

beacon

[no] beacon

Syntax Description

no

(Optional) Negate a command or set its defaults

beacon

Disable/enable the beacon for an interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

begin exclude include end

| { begin | exclude | include | end } [ -i | -x ] + <expr> [ next <num> | prev <num> ] +

Syntax Description

|

Pipe command output to filter

begin

Begin with the line that matches

exclude

Exclude lines that match

include

Include lines that match

end

End with the line that matches

-i

(Optional) Ignore case difference when comparing strings

-x

(Optional) Print only lines where the match is a whole line

expr

Search for the expression

next

(Optional) Print <num> lines of context after every matching line

prev

(Optional) Print <num> lines of context before every matching line

num

(Optional) Print <num> lines of context

Command Mode

  • /output

bestpath

[no] bestpath { always-compare-med | med { missing-as-worst | non-deterministic | confed } | compare-routerid | compare-neighborid | cost-community ignore | as-path { multipath-relax | ignore } | igp-metric ignore }

Syntax Description

no

(Optional) Negate a command or set its defaults

bestpath

Change default bestpath selection algorithm

always-compare-med

Compare MED on paths from different AS

med

MED

missing-as-worst

Treat missing MED as highest MED

non-deterministic

Not always pick the best-MED path among paths from same AS

compare-routerid

Compare router-id for identical EBGP paths

compare-neighborid

When more paths available than max path config, use neighborid tibreaker

cost-community

cost community

ignore

Ignore cost communities in bestpath selection

confed

Compare MED only from paths originated from within a confederation

as-path

AS-Path

multipath-relax

Relax AS-Path restriction when choosing multipaths

ignore

Ignore AS-Path during bestpath selection

igp-metric

IGP metric for next-hop

ignore

Ignore IGP metric for next-hop during bestpath selection

Command Mode

  • /exec/configure/router-bgp/vrf-cmds

bestpath origin-as allow invalid

[no] bestpath origin-as allow invalid

Syntax Description

no

(Optional) Negate a command or set its defaults

bestpath

Change default bestpath selection algorithm

origin-as

Use RPKI origin-as validity in bestpath selection

allow

BGP bestpath selection will allow invalid origin-AS

invalid

BGP bestpath selection will allow invalid origin-AS

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

bestpath origin-as use-validity

[no] bestpath origin-as use-validity

Syntax Description

no

(Optional) Negate a command or set its defaults

bestpath

Change default bestpath selection algorithm

origin-as

Use RPKI origin-as validity in bestpath selection

use-validity

BGP bestpath selection will use origin-as validity

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Enable IPv4 BFD on all ISIS interfaces

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv4 /exec/configure/router-isis/router-isis-af-ipv6

bfd

[ no | default ] bfd [ multihop | singlehop ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

bfd

Bidirectional Fast Detection for the neighbor

multihop

(Optional) Multihop session

singlehop

(Optional) Single-hop session

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

bfd

[no] bfd [ ipv4 | ipv6 ]

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

ipv4

(Optional) ipv4 sessions

ipv6

(Optional) ipv6 sessions

Command Mode

  • /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Enable BFD on all OSPF interfaces

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Enable BFD on all EIGRP interfaces

Command Mode

  • /exec/configure/router-eigrp /exec/configure/router-eigrp/router-eigrp-vrf /exec/configure/router-eigrp/router-eigrp-af-common

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Enable BFD on all OSPF interfaces

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Configure MPLS BFD traffic Engineering Segment Routing liveness detection configurations

Command Mode

  • /exec/configure/sr/te/live-det/mpls

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Configure MPLS BFD traffic Engineering Segment Routing liveness detection configurations

Command Mode

  • /exec/configure/sr/te/color/live-det/mpls

bfd

[no] bfd

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

Configure MPLS BFD traffic Engineering Segment Routing liveness detection configurations

Command Mode

  • /exec/configure/sr/te/pol/live-det/mpls

bfd authentication interop

bfd authentication interop | no bfd authentication interop

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

authentication

Configure BFD authentication parameters

interop

Allows keys to be sent in network format to interop with non N3k/N9K switches

Command Mode

  • /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd authentication key-id key

bfd [ { ipv4 | ipv6 } ] authentication <auth_name> key-id <key_id_val> { key <key_val> | hex-key <h_key_val> } | no bfd [ { ipv4 | ipv6 } ] authentication

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

authentication

Configure BFD authentication parameters

ipv4

(Optional) ipv4 sessions

ipv6

(Optional) ipv6 sessions

auth_name

auth algorithm

key-id

Key ID to use in BFD frames

key_id_val

Key ID value

key

ASCII SHA1 secret

hex-key

HEX binary SHA1 secret

key_val

SHA1 secret value

h_key_val

SHA1 secret value. e.g ABCD123

Command Mode

  • /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd echo-interface

[no] bfd echo-interface <ifindex>

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

echo-interface

Configure interface used for bfd echo frames

ifindex

loopback interface

Command Mode

  • /exec/configure

bfd echo-rx-interval

bfd [ ipv4 | ipv6 ] echo-rx-interval <intv> | no bfd [ ipv4 | ipv6 ] echo-rx-interval

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

ipv6

(Optional) ipv6 sessions

ipv4

(Optional) ipv4 sessions

echo-rx-interval

Configure BFD session echo rx interval

intv

Echo Rx Interval in milliseconds

Command Mode

  • /exec/configure /exec/configure/if-ma /exec/configure/if-ma-p2p

bfd echo

[no] bfd [ { ipv4 | ipv6 } ] echo

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

echo

Configure Echo function for all address families

ipv4

(Optional) ipv4 sessions

ipv6

(Optional) ipv6 sessions

Command Mode

  • /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd hw-offload

[no] bfd hw-offload

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

hw-offload

Configure hardware offload

Command Mode

  • /exec/configure

bfd interval

[no] bfd [ ipv4 | ipv6 ] interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

interval

Configure BFD session interval parameters

ipv6

(Optional) ipv6 sessions

ipv4

(Optional) ipv4 sessions

min_tx_mills

(Optional) TX interval in milliseconds

min_rx

(Optional) Minimum RX interval

min_rx_mills

(Optional) RX interval in milliseconds

multiplier

(Optional) Configure detect multiplier for bfd sessions

int_mult

(Optional) Detect Multiplier

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd interval

[no] bfd [ ipv4 | ipv6 ] interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

interval

Configure BFD session interval parameters

ipv6

(Optional) ipv6 sessions

ipv4

(Optional) ipv4 sessions

min_tx_mills

(Optional) TX interval in milliseconds

min_rx

(Optional) Minimum RX interval

min_rx_mills

(Optional) RX interval in milliseconds

multiplier

(Optional) Configure detect multiplier for bfd sessions

int_mult

(Optional) Detect Multiplier

Command Mode

  • /exec/configure

bfd interval min_rx multiplier

bfd [ ipv6 | ipv4 ] interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>

Syntax Description

bfd

BFD commands

interval

Configure BFD session interval parameters

ipv6

(Optional) ipv6 sessions

ipv4

(Optional) ipv4 sessions

min_tx_mills

TX interval in milliseconds

min_rx

Minimum RX interval

min_rx_mills

RX interval in milliseconds

multiplier

Configure detect multiplier for bfd sessions

int_mult

Detect Multiplier

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd interval min_rx multiplier

bfd [ ipv6 | ipv4 ] interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>

Syntax Description

bfd

BFD commands

interval

Configure BFD session interval parameters

ipv6

(Optional) ipv6 sessions

ipv4

(Optional) ipv4 sessions

min_tx_mills

TX interval in milliseconds

min_rx

Minimum RX interval

min_rx_mills

RX interval in milliseconds

multiplier

Configure detect multiplier for bfd sessions

int_mult

Detect Multiplier

Command Mode

  • /exec/configure

bfd local-address

bfd local-address { <src_ip> | <src_ipv6> } | no bfd local-address

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

local-address

Configure the source IP address to be used for BFD session

src_ip

Source IP value

Command Mode

  • /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p

bfd multihop authentication key-id key

bfd multihop authentication <auth_name> key-id <key_id_val> { key <key_val> | hex-key <h_key_val> } | { no | default } bfd multihop authentication [ <auth_name> key-id <key_id_val> { key <key_val> | hex-key <h_key_val> } ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

bfd

Bidirectional Fast Detection for the neighbor

multihop

For Multihop sessions

authentication

Configure BFD authentication parameters

auth_name

auth algorithm

key-id

Key ID to use in BFD frames

key_id_val

Key ID value

key

ASCII SHA1 secret

hex-key

HEX binary SHA1 secret

key_val

SHA1 secret value

h_key_val

SHA1 secret value. e.g ABCD123

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

bfd multihop interval

[no] bfd multihop interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

multihop

Configure BFD Multihop session interval parameters

interval

Configure BFD multihop session interval parameters

min_tx_mills

(Optional) TX interval in milliseconds

min_rx

(Optional) Minimum RX interval

min_rx_mills

(Optional) RX interval in milliseconds

multiplier

(Optional) Configure detect multiplier for bfd multihop sessions

int_mult

(Optional) Detect Multiplier

Command Mode

  • /exec/configure

bfd multihop interval min_rx multiplier

bfd multihop interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> | { no | default } bfd multihop interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

bfd

Bidirectional Fast Detection for the neighbor

multihop

Multihop session

interval

Configure BFD session interval parameters

min_tx_mills

TX interval in milliseconds

min_rx

Minimum RX interval

min_rx_mills

RX interval in milliseconds

multiplier

Configure detect multiplier for bfd sessions

int_mult

Detect Multiplier

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

bfd multihop interval min_rx multiplier

bfd multihop interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>

Syntax Description

bfd

BFD commands

multihop

Configure BFD Multihop session interval parameters

interval

Configure BFD multihop session interval parameters

min_tx_mills

TX interval in milliseconds

min_rx

Minimum RX interval

min_rx_mills

RX interval in milliseconds

multiplier

Configure detect multiplier for bfd multihop sessions

int_mult

Detect Multiplier

Command Mode

  • /exec/configure

bfd optimize subinterface

[no] bfd [ ipv4 ] optimize subinterface

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

optimize

optimize

subinterface

optimize subinterfaces

ipv4

(Optional) ipv4 sessions

Command Mode

  • /exec/configure/if-ma /exec/configure/if-ma-p2p

bfd per-link

[no] bfd [ { ipv4 | ipv6 } ] per-link

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

per-link

Run BFD sessions on each port-channel link

ipv4

(Optional) ipv4 sessions

ipv6

(Optional) ipv6 sessions

Command Mode

  • /exec/configure/if-eth-port-channel /exec/configure/if-port-channel-sub /exec/configure/if-eth-port-channel-p2p

bfd slow-timer

bfd [ { ipv4 | ipv6 } ] slow-timer <int_slow_timer> | no bfd [ { ipv4 | ipv6 } ] slow-timer

Syntax Description

no

Negate a command or set its defaults

bfd

BFD commands

slow-timer

Configure slow mode timer for sessions

int_slow_timer

Slow rate timer in milliseconds

ipv4

(Optional) ipv4 sessions

ipv6

(Optional) ipv6 sessions

Command Mode

  • /exec/configure

bfd startup-timer bfd startup-timer

bfd startup-timer <int_startup_timer> | [ no ] bfd startup-timer

Syntax Description

no

(Optional) Negate a command or set its defaults

bfd

BFD commands

startup-timer

Configure Delayed Start Up timer for sessions

int_startup_timer

Start Up timer in seconds

Command Mode

  • /exec/configure

bfshell

bfshell

Syntax Description

bfshell

bfshell

Command Mode

  • /exec

bfshell cmd

bfshell cmd <cmd>

Syntax Description

bfshell

bfshell

cmd

Specify command

cmd

Quoted commands to be exec

Command Mode

  • /exec

bfshell module

bfshell module <module>

Syntax Description

bfshell

bfshell

module

Select module

module

Module number

Command Mode

  • /exec

bfshell module cmd

bfshell module <module> cmd <cmd>

Syntax Description

bfshell

bfshell

module

Select module

cmd

Specify command

module

Module number

cmd

Quoted commands to be exec

Command Mode

  • /exec

binary-location

[no] binary-location <source-uri>

Syntax Description

no

(Optional) Negate a command or set its defaults

binary-location

the location binaries are downloaded from

source-uri

Location for restoration to pick up binaries

Command Mode

  • /exec/configure/personality

bind interface

[no] bind interface <interface-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

bind

Bind the VFC

interface

Bind the VFC to an interface

interface-name

Interface name

Command Mode

  • /exec/configure/if-vfc

bind mac-address

[no] bind mac-address <mac0>

Syntax Description

no

(Optional) Negate a command or set its defaults

bind

Bind the VFC

mac-address

Bind the VFC to a MAC Address

mac0

Enter MAC addrress in dotted hex format

Command Mode

  • /exec/configure/if-vfc

blink

[no] blink { module <module> | <s0> <santa-cruz-range> | chassis | powersupply <psnum> | fan <fan_num> }

Syntax Description

no

(Optional) Negate a command or set its defaults

blink

blink locator led

module

blink module led

module

please enter the module number

s0

blink a specific xbar

santa-cruz-range

please enter the xbar number

chassis

blink chassis led

powersupply

blink powersupply led

psnum

powersupply number

fan

blink Fan led

fan_num

fan number

Command Mode

  • /exec

bloggerd auto-collect component

{ bloggerd auto-collect component { ethport { enable | disable } | kern { enable | disable } | bgp { enable | disable } | cdp { enable | disable } | snmpmib_proc { enable | disable } | arp { enable | disable } | icmpv6 { enable | disable } | l3vm { enable | disable } | pktmgr { enable | disable } | feature-mgr { enable | disable } | vpc { enable | disable } | port-channel { enable | disable } | mfdm { enable | disable } | spm { enable | disable } | dhcp_snoop { enable | disable } | mrib { enable | disable } | fex { enable | disable } | icam { enable | disable } | isis { enable | disable } | pim { enable | disable } | vmtracker { enable | disable } | tahusd { enable | disable } | adjmgr { enable | disable } | lldp { enable | disable } | udld { enable | disable } | smm { enable | disable } | lacp { enable | disable } | hsrp_engine { enable | disable } | vrrp-eng { enable | disable } | vrrp-cfg { enable | disable } | ip { enable | disable } | netstack { enable | disable } | clis { enable | disable } | pltfm_config { enable | disable } | nbm { enable | disable } | bcm_usd { enable | disable } | statsclient { enable | disable } | sysmgr { enable | disable } | jer_usd { enable | disable } | m2rib { enable | disable } | ipqosmgr { enable | disable } | hmm { enable | disable } | l2fm { enable | disable } | sla_sender { enable | disable } | sla_responder { enable | disable } | sla_twamp { enable | disable } | ufdm { enable | disable } | vrrpv3 { enable | disable } | iftmc { enable | disable } | eltm { enable | disable } | tctrl_usd { enable | disable } | CrdCfg { enable | disable } | ngoam { enable | disable } | nve { enable | disable } | cardclient { enable | disable } | l2rib { enable | disable } | eigrp { enable | disable } | kafka { enable | disable } | im { enable | disable } | pfma { enable | disable } | cfs { enable | disable } | aclqos { enable | disable } | tun_enc_mgr { enable | disable } | cts { enable | disable } | vntag_mgr { enable | disable } | rip { enable | disable } | sdaa { enable | disable } | ipfib { enable | disable } | ospfv3 { enable | disable } | ospf { enable | disable } | aclmgr { enable | disable } | bfd { enable | disable } } }

Syntax Description

bloggerd

Syslog based auto-collect for components

auto-collect

Auto-collect for different components

component

Component name for syslog based auto-collect

kern

Auto-collect for Kernel

enable

Enable the syslog based auto-collect

disable

Disable the syslog based auto-collect

Command Mode

  • /exec

bloggerd clear evtlog stats

bloggerd clear evtlog stats

Syntax Description

bloggerd

Blogger commands

clear

Reset the eventlog stats

evtlog

Event logs

stats

Event log statistics

Command Mode

  • /exec

bloggerd live-process-core sap

bloggerd live-process-core sap <sap>

Syntax Description

bloggerd

Blogger commands

live-process-core

Dump the core of the live-process

sap

Dump core for a particular SAP

sap

Enter a valid SAP.

Command Mode

  • /exec

bloggerd log-dump all

[no] bloggerd log-dump { all | [ module <module> ] sap <sap_num> [ vdc <new_id> | vdc-all ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

bloggerd

Blogger commands

log-dump

Dump Log Buffer

all

Log Dump for ALL services across ALL modules in the switch on reaching threshold

module

(Optional) Enable Buffer Dump for particular Module

module

(Optional) Enter a valid Module Number

sap

Enable Buffer Dump for a particular sap

sap_num

Enter a valid SAP. Enter 0 for ALL SAPs in this VDC

vdc

(Optional) Enable Log Dump for a particular VDC. DEFAULT_VDC by default

new_id

(Optional) Enter a valid VDC ID

vdc-all

(Optional) Enable Log Dump for the sap on ALL VDCs

Command Mode

  • /exec/configure

bloggerd log-dump once log-buffer sap

bloggerd log-dump once log-buffer sap <sap0>

Syntax Description

bloggerd

Blogger commands

log-dump

Dump Log Buffer

once

Dump Log Buffer once immediately

log-buffer

Dump Log buffer

sap

Enable Buffer Dump for a particular sap

sap0

Enter 0 for ALL SAPs in this VDC

Command Mode

  • /exec

bloggerd log-dump once log-buffer sap event-history

bloggerd log-dump once log-buffer sap <sap> event-history { errors | msgs | { app-specific <uuid> instance <buffer-instance> } | all }

Syntax Description

bloggerd

Blogger commands

log-dump

Dump Log Buffer

once

Dump Log Buffer once immediately

log-buffer

Dump Log buffer

sap

Enable Buffer Dump for a particular sap

sap

Enter a valid SAP for a specific process

event-history

Event-History Buffers

errors

event-history errors

msgs

event-history messages

app-specific

application specific event history

uuid

Enter valid app's UUID

instance

Buffer Instance of the App-Specific SDWrap buffer

buffer-instance

Enter a valid SDWrap buffer instance for the app

all

All event-history buffers on the SAP

Command Mode

  • /exec

bloggerd log-dump once pss uuid

bloggerd log-dump once pss uuid <uuid>

Syntax Description

bloggerd

Blogger commands

log-dump

Dump Log Buffer

once

Dump Log Buffer once immediately

pss

Dump PSS

uuid

Dump PSS for a particular UUID

uuid

Enter a app's UUID

Command Mode

  • /exec

bloggerd log-snapshot

bloggerd log-snapshot [ <identifier> | time <i0> | size <i1> | purge threshold <i2> | all | storage { bootflash | logflash | usb1 | usb2 } ] +

Syntax Description

bloggerd

Blogger commands

log-snapshot

Event Logs

identifier

(Optional) Identifier of the snapshot

time

(Optional) Snapshot based on time

i0

(Optional) Snapshot of last xx mins logs

size

(Optional) Snapshot based on size

i1

(Optional) Snapshot size in MB

storage

(Optional) List of allowed file systems for storing snapshot

bootflash

(Optional) Snapshot will be stored in bootflash:evt_log_snapshot

logflash

(Optional) Snapshot will be stored in logflash:evt_log_snapshot

usb1

(Optional) Snapshot will be stored in usb1:evt_log_snapshot

usb2

(Optional) Snapshot will be stored in usb2:evt_log_snapshot

purge

(Optional) Older snapshots will be purged

threshold

(Optional) Threshold value, after which purge kicks in

i2

(Optional) Snapshots will be purged once the threhold is reached

all

(Optional) Snapshot will be collected along with log-dump once sap 0

Command Mode

  • /exec

bloggerd log-throttle

[no] bloggerd log-throttle [ min-rollover <min-rollover> max-rollover-per-minute <max-rollover-per-minute> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

bloggerd

Blogger commands

log-throttle

Enable Log Dump Throttling for all NxOS services

min-rollover

(Optional) Number of minimum buffer rollovers before starting to throttle. Default: 5

min-rollover

(Optional) Enter the mininum number of roll-overs before throttleing log-dump. Default: 5

max-rollover-per-minute

(Optional) Maximum allowed buffer rollovers per minute. Default: 1

max-rollover-per-minute

(Optional) Enter the maximum allowed roll-overs per minute before throttling. Default: 1

Command Mode

  • /exec/configure

bloggerd log-transfer

bloggerd log-transfer { <ip-addr> <path> | logflash }

Syntax Description

bloggerd

Blogger commands

log-transfer

Configure log transfer

ip-addr

IP addr of logging server

path

Path in tftp server to store logs. Eg: logOutput

logflash

Move all log-files to logflash

Command Mode

  • /exec/configure

bloggerd log-transfer

[no] bloggerd log-transfer

Syntax Description

no

Negate a command or set its defaults

bloggerd

Blogger commands

log-transfer

Configure log transfer

Command Mode

  • /exec/configure

bloggerd parse log-buffer file

bloggerd parse log-buffer { file | directory } <uri0> [ dsf_table <uri1> ]

Syntax Description

bloggerd

Blogger commands

parse

Parse a file

log-buffer

Parse buffer log file

directory

Enter path of directory

file

Enter file name. Please unzip file before parsing!

uri0

Linux path to file/directory (Eg: /bootflash/abc)

dsf_table

(Optional) Enter dsf table file name.

uri1

(Optional) Linux path to file/directory (Eg: /bootflash/abc)

Command Mode

  • /exec

bloggerd parse log-buffer file sap

bloggerd parse log-buffer file <uri0> sap <sap-num>

Syntax Description

bloggerd

Blogger commands

parse

Parse a file

log-buffer

Parse buffer log file

file

Enter file name. Please unzip file before parsing!

uri0

Linux path to file (Eg: /bootflash/abc)

sap

SAP of the application which should parse the file

sap-num

Enter a valid SAP. Enter 0 for ALL SAPs in this VDC

Command Mode

  • /exec

bloggerd parse pss file

bloggerd parse pss file <uri0>

Syntax Description

bloggerd

Blogger commands

parse

Parse a file

pss

Parse a dumped PSS File

file

Enter file name (without pss extensions). Please unzip file before parsing!

uri0

Linux path to file/directory (Eg: /bootflash/abc)

Command Mode

  • /exec

bloggerd reparse log-profile

bloggerd reparse log-profile

Syntax Description

bloggerd

Blogger commands

reparse

Parse the YAML profile file

log-profile

Log Profile in YAML

Command Mode

  • /exec

bmp-activate-server

bmp-activate-server <server-number> | { no | default } bmp-activate-server <server-number>

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

bmp-activate-server

Activate BMP monitoring for the peer

server-number

Server Id

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

bmp-server

[no] bmp-server <server-number>

Syntax Description

no

(Optional) Negate a command or set its defaults

bmp-server

Configure bmp-server

server-number

server number value

Command Mode

  • /exec/configure/router-bgp

boot-order

boot-order <new_id>

Syntax Description

boot-order

The order at which a vdc will boot up. VDCs at the same level will be started parallely

new_id

The order at which a vdc will boot up. VDCs at the same level will be started parallely

Command Mode

  • /exec/configure/vdc

boot

{ boot <s0> <uri0> [ module [ <module> ] ] | no boot <s0> [ <uri0> [ module [ <module> ] ] ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

s0

use [show boot variables] for list of keywords

uri0

Enter module image uri

module

(Optional) Enter module number for the image

module

(Optional) Enter module number

Command Mode

  • /exec/configure

boot aci

{ boot aci <uri0> | no boot aci [ <uri0> ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

aci

Configure ACI image

uri0

Enter ACI image uri

Command Mode

  • /exec/configure

boot auto-copy

[no] boot auto-copy

Syntax Description

no

(Optional) Negate a command or set its defaults

boot

Configure boot variables

auto-copy

Turns on/off autocopy of bootvar images

Command Mode

  • /exec/configure

boot fex

{ boot fex [ <uri0> ] | no boot fex [ <uri0> ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

fex

Configure FEX image

uri0

(Optional) Enter FEX image uri

Command Mode

  • /exec/configure

boot kickstart

{ boot kickstart <uri0> | no boot kickstart [ <uri0> ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

kickstart

Configure kickstart image

uri0

Enter Kickstart image uri

Command Mode

  • /exec/configure

boot mode docker_cluster

[no] boot mode docker_cluster [ dhcp <option> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

boot

Configure boot mode

mode

boot mode

docker_cluster

Turns on/off docker_cluster mode

dhcp

(Optional) Custom DHCP option

option

(Optional) Option, default is 250

Command Mode

  • /exec/configure

boot mode lxc

[no] boot mode lxc

Syntax Description

no

(Optional) Negate a command or set its defaults

boot

Configure boot mode

mode

boot mode

lxc

Turns on/off lxc mode

Command Mode

  • /exec/configure

boot nxos

{ boot nxos <uri0> | no boot nxos [ <uri0> ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

nxos

Configure NXOS image

uri0

Enter nxos image uri

Command Mode

  • /exec/configure

boot nxos sup-1

{ boot nxos <uri0> sup-1 | no boot nxos <uri0> sup-1 }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

nxos

Configure NXOS image

uri0

Enter nxos image uri

sup-1

Enter sup-1 to configure the 1st sup

Command Mode

  • /exec/configure

boot nxos sup-1 sup-2

{ boot nxos <uri0> sup-1 sup-2 | no boot nxos <uri0> sup-1 sup-2 }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

nxos

Configure NXOS image

uri0

Enter nxos image uri

sup-1

Enter sup-1 to configure the 1st sup

sup-2

Enter sup-2 to configure the 2nd sup

Command Mode

  • /exec/configure

boot nxos sup-2

{ boot nxos <uri0> sup-2 | no boot nxos <uri0> sup-2 }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

nxos

Configure NXOS image

uri0

Enter nxos image uri

sup-2

Enter sup-2 to configure the 2nd sup

Command Mode

  • /exec/configure

boot order bootflash

{ boot order bootflash [ pxe ] | no boot order bootflash [ pxe ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

order

Configure loader fallback order

bootflash

Boot from Bootflash

pxe

(Optional) Pxe Boot

Command Mode

  • /exec/configure

boot order pxe

{ boot order pxe [ bootflash ] | no boot order pxe [ bootflash ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

order

Configure loader fallback order

pxe

Pxe Boot

bootflash

(Optional) Boot from Bootflash

Command Mode

  • /exec/configure

boot poap enable

{ boot poap enable | no boot poap enable }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

poap

feature poap

enable

Enable Perpetual POAP making POAP kick in on reload even with startup-config

Command Mode

  • /exec/configure

boot system

{ boot system <uri0> | no boot system [ <uri0> ] }

Syntax Description

no

Negate a command or set its defaults

boot

Configure boot variables

system

Configure system image

uri0

Enter system image uri

Command Mode

  • /exec/configure

broadcast

[no] broadcast

Syntax Description

no

(Optional) Negate a command or set its defaults

broadcast

Allow broadcast frames in the default-zone

Command Mode

  • /exec/configure/default-zone/attribute-group

broadcast

[no] broadcast

Syntax Description

no

(Optional) Negate a command or set its defaults

broadcast

Allow broadcast frames in the zone

Command Mode

  • /exec/configure/attribute-group

buffer-boost

[no] buffer-boost

Syntax Description

no

(Optional) Negate a command or set its defaults

buffer-boost

Enable extra buffers for this interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

buffer-delete

buffer-delete { <id-range> | <id> | all }

Syntax Description

buffer-delete

delete buffered command(s)

id-range

Range(whole-number) of command id(s) to be deleted from switch-profile buffer

id

Exact command id (x.x.x format) to be deleted from switch-profile buffer

all

delete all buffered commands

Command Mode

  • /exec/configure

buffer-drop collector

[no] buffer-drop collector <collectorname>

Syntax Description

buffer-drop

Enable/Disable buffer-drop configuration

collector

Define a collector

collectorname

Name of collector

Command Mode

  • /exec/configure/config-buffer-drop

buffer-drop monitor

[no] buffer-drop monitor <monitorname>

Syntax Description

buffer-drop

Enable/Disable buffer-drop configuration

monitor

Define a buffer-drop Monitor

monitorname

Name of buffer-drop Monitor

Command Mode

  • /exec/configure/config-buffer-drop

buffer-drop system monitor

[no] buffer-drop system monitor <monitorname>

Syntax Description

system

global config

buffer-drop

buffer-drop global settings

monitor

buffer-drop Monitor to be applied

monitorname

buffer-drop Monitor to be applied

Command Mode

  • /exec/configure/config-buffer-drop

buffer-latency collector

[no] buffer-latency collector <collectorname>

Syntax Description

buffer-latency

Enable/Disable buffer-latency configuration

collector

Define a collector

collectorname

Name of collector

Command Mode

  • /exec/configure/config-buffer-latency

buffer-latency monitor

[no] buffer-latency monitor <monitorname>

Syntax Description

buffer-latency

Enable/Disable buffer-latency configuration

monitor

Define a buffer-latency Monitor

monitorname

Name of buffer-latency Monitor

Command Mode

  • /exec/configure/config-buffer-latency

buffer-latency record

[no] buffer-latency record <recordname>

Syntax Description

buffer-latency

Enable/Disable buffer-latency configuration

record

Define a buffer-latency record

recordname

Name of buffer-latency record

Command Mode

  • /exec/configure/config-buffer-latency

buffer-latency system monitor

[no] buffer-latency system monitor <monitorname>

Syntax Description

system

global config

buffer-latency

buffer-latency global settings

monitor

buffer-latency Monitor to be applied

monitorname

buffer-latency Monitor to be applied

Command Mode

  • /exec/configure/config-buffer-latency

buffer-latency threshold

[no] buffer-latency threshold <thresholdname> <thresholdvalue>

Syntax Description

buffer-latency

buffer-latency configuration

threshold

Define a threshold value

thresholdname

Name for threshold

thresholdvalue

Threshold value in ns

Command Mode

  • /exec/configure/config-buffer-latency

buffer-move

buffer-move <fromid> <toid>

Syntax Description

buffer-move

move buffered command(s)

fromid

Command id of command(s) to be moved in switch-profile buffer

toid

New command id to be assigned in switch-profile buffer

Command Mode

  • /exec/configure

burst-detect active-queue-percentage

[no] burst-detect active-queue-percentage <value-in-percent>

Syntax Description

no

(Optional) Negate a command or set its defaults

burst-detect

Global burst-detect settings

active-queue-percentage

Active queue percentage

value-in-percent

Percent

Command Mode

  • /exec/configure/system/qos

burst-detect enable

[no] burst-detect enable

Syntax Description

no

(Optional) Negate a command or set its defaults

burst-detect

Specify OOBST burst-detect thresholds for the class

enable

enable

Command Mode

  • /exec/configure/policy-map/type/queuing/class

burst-detect rise-threshold bytes fall-threshold bytes2

[no] burst-detect rise-threshold { { <value-in-bytes> bytes } | { <value-in-percent> percent } } fall-threshold { { <value-in-bytes> bytes2 } | { <value-in-percent> percent2 } }

Syntax Description

no

(Optional) Negate a command or set its defaults

burst-detect

Specify OOBST burst-detect thresholds for the class

rise-threshold

Threshold bytes(queue depth) to start monitoring burst

value-in-bytes

bytes

bytes

value-in-percent

Value in percentage

percent

Percent

fall-threshold

Threshold bytes(queue depth) to stop monitoring burst

value-in-bytes

bytes2

bytes2

value-in-percent

Value in percentage

percent2

Percent

Command Mode

  • /exec/configure/policy-map/type/queuing/class