L Commands

l2rib dup-host-mac-detection

{ no l2rib dup-host-mac-detection } | { l2rib dup-host-mac-detection <num-of-moves> <duration> }

Syntax Description

no

Negate a command or set its defaults

l2rib

Layer 2 routing information base

dup-host-mac-detection

Set Duplicate-Host-MAC-Detection parameters

num-of-moves

Number of host moves to be allowed

duration

Duplicate detection timeout in secs for host moves

Command Mode

  • /exec/configure

l2rib dup-host-mac-recovery

{ no l2rib dup-host-mac-recovery } | { l2rib dup-host-mac-recovery <timeout> <retry-count> }

Syntax Description

no

Negate a command or set its defaults

l2rib

Layer 2 routing information base

dup-host-mac-recovery

Set Duplicate-Host-MAC-Recovery (Unfreeze) parameters

timeout

Unfreeze timeout (secs)

retry-count

Unfreeze retry count

Command Mode

  • /exec/configure

label-allocation-mode per-vrf

[no] label-allocation-mode per-vrf

Syntax Description

no

(Optional) Negate a command or set its defaults

label-allocation-mode

Configure label allocation mode

per-vrf

per VRF label allocation mode

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

label allocate global

[no] label allocate global { all-routes | host-routes | prefix-list <pfx-list> }

Syntax Description

no

(Optional) Negate a command or set its defaults

label

LDP label configuration

allocate

Allocate local labels

global

Specify default VPN Routing/Forwarding instance

all-routes

Allocate local labels for all routes

host-routes

Allocate local labels for host routes only (default)

prefix-list

Specify a prefix-list for local label filtering

pfx-list

IP prefix-list for destination prefixes

Command Mode

  • /exec/configure/ldp

lacp graceful-convergence

lacp graceful-convergence | no lacp graceful-convergence

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

graceful-convergence

Configure port-channel lacp graceful convergence. Disable this only with lacp ports connected to Non-Nexus peer. Disabling this with Nexus peer can lead to port suspension

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp max-bundle

lacp max-bundle <max-bundle-number> | no lacp max-bundle [ <max-bundle-number> ]

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

max-bundle

Configure the port-channel max-bundle

max-bundle-number

Enter the max-bundle number

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp min-links

lacp min-links <min-links-number> | no lacp min-links [ <min-links-number> ]

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

min-links

Configure the port-channel min-links

min-links-number

Enter the min-link number

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description

no

(Optional) Negate a command or set its defaults

lacp

Set LACP parameters for the interface

mode

Enter the LACP mode

delay

Configure delayed lacp on the port-channel

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description

no

(Optional) Negate a command or set its defaults

lacp

Set LACP parameters for the interface

mode

Enter the LACP mode

delay

Configure delayed lacp on the port-channel

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp port-number front-panel

lacp port-number front-panel | no lacp port-number front-panel

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

port-number

Configure port-number in LACP port-channels

front-panel

Configure front panel based port numbering for LACP port-channels

Command Mode

  • /exec/configure

lacp port-priority

lacp port-priority <port-pri> | no lacp port-priority

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

port-priority

Set LACP port priority

port-pri

Enter port priority

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

lacp rate

[no] lacp rate

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

rate

Configure rate at which PDUs are sent by LACP

Command Mode

  • /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp rate

lacp rate <rate_type>

Syntax Description

lacp

Set LACP parameters for the interface

rate

Configure rate at which PDUs are sent by LACP

rate_type

Rate type

Command Mode

  • /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp suspend-individual

lacp suspend-individual [ pxe [ <pxe-timeout> ] ] | no lacp suspend-individual [ pxe [ <pxe-timeout> ] ]

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

suspend-individual

Configure lacp port-channel state. Disabling this will cause lacp to put the port to individual state and not suspend the port in case it does not get LACP BPDU from the peer ports in the port-channel

pxe

(Optional) Disabling this would cause lacp to put only one port to individual state in case it does not get LACP BPDU from the peer port in the port-channel

pxe-timeout

(Optional) PXE timeout value in seconds (default 10 seconds)

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp system-mac

lacp system-mac <mac-address> [ role <role> ] | no lacp system-mac

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

system-mac

Configure the MAC address to be used for the LACP Protocol exchanges

mac-address

MAC-address(FORMAT :xxxx.xxxx.xxxx)

role

(Optional) Configure the role for this Switch

role

(Optional) Role played by the Switch

Command Mode

  • /exec/configure

lacp system-priority

lacp system-priority <sys-pri> | no lacp system-priority

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

system-priority

Set LACP system priority

sys-pri

Enter System Priority

Command Mode

  • /exec/configure

lacp vpc-convergence

lacp vpc-convergence | no lacp vpc-convergence

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

vpc-convergence

Enable lacp convergence for vPC port channels.

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

last

| last [ <lines> ]

Syntax Description

|

Pipe command output to filter

last

Display last lines

lines

(Optional) number of lines to print

Command Mode

  • /output

latency

{ [ no ] latency <lat> | no latency }

Syntax Description

latency

Provide the latency value for this POSTCARD queue_profile

lat

queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

  • /exec/configure/config-postcard-q-prof

latency

{ [ no ] latency <lat> | no latency }

Syntax Description

latency

Provide the latency value for this INT queue_profile

lat

queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

  • /exec/configure/config-int-q-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description

latency

Provide the latency value for this POSTCARD flow-profile

quantization

Provide the latency value for this POSTCARD flow-profile

lat

flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any postcard in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28. Default is 11.

Command Mode

  • /exec/configure/config-postcard-flow-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description

latency

Provide the latency value for this INT flow-profile

quantization

Provide the latency value for this INT flow-profile

lat

flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any point in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28 Default is 11.

Command Mode

  • /exec/configure/config-int-flow-prof

layer-2 multicast lookup mac

[no] layer-2 multicast lookup mac

Syntax Description

no

(Optional) Negate a command or set its defaults

layer-2

set layer2 multicast lkup mode

multicast

set layer2 multicast lkup mode

lookup

lkup type can be either mac or ip based

mac

set mac based multicast lkup mode

Command Mode

  • /exec/configure/vlan-config /exec/configure/bdomain

layer2-switched flow monitor input

[no] layer2-switched flow monitor <monitorname> { input | output }

Syntax Description

layer2-switched

Configure L2 features

flow

NetFlow related commands

monitor

Apply a Flow Monitor to this interface

monitorname

Name of Flow Monitor

input

Apply Flow Monitor on input traffic

output

Apply Flow Monitor on output traffic

Command Mode

  • /exec/configure/if-switching

layer2-switched flow monitor input

[no] layer2-switched flow monitor <monitorname> { input | output }

Syntax Description

layer2-switched

Configure L2 features

flow

NetFlow related commands

monitor

Apply a Flow Monitor to this interface

monitorname

Name of Flow Monitor

input

Apply Flow Monitor on input traffic

output

Apply Flow Monitor on output traffic

Command Mode

  • /exec/configure/if-veth /exec/configure/if-veth-all /exec/configure/if-vethernet /exec/configure/if-veth-any

layer3 peer-router

layer3 peer-router | no layer3 peer-router

Syntax Description

no

Negate a command or set its defaults

layer3

Enable layer 3 functionality

peer-router

no change for TTL of packets destined to the peer

Command Mode

  • /exec/configure/vpc-domain

layer3 peer-router syslog

layer3 peer-router syslog [ interval <syslog-interval> ] | no layer3 peer-router syslog

Syntax Description

no

Negate a command or set its defaults

layer3

Enable layer 3 functionality

peer-router

no change for TTL of packets destined to the peer

syslog

print layer 3 protocol syslog

interval

(Optional) how frequent to print the syslog

syslog-interval

(Optional) how many seconds to print a syslog

Command Mode

  • /exec/configure/vpc-domain

lcnd push_to_klm address port vlan

lcnd push_to_klm address <macaddr> port <portnum> vlan <vlanid>

Syntax Description

lcnd

LCND configuration

push_to_klm

Push MAC address to auth_db

address

MAC address

macaddr

MAC address

port

Port number

portnum

Port number

vlan

VLAN id

vlanid

VLAN id

Command Mode

  • /exec/configure

ldap-search-map

[no] ldap-search-map

Syntax Description

no

Negate a command or set its defaults

ldap-search-map

Set one of the configured search-map as active

Command Mode

  • /exec/configure/ldap

ldap-search-map

ldap-search-map <s0>

Syntax Description

ldap-search-map

Set one of the configured search-map as active

s0

Name of the search-map

Command Mode

  • /exec/configure/ldap

ldap-server deadtime

[no] ldap-server deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

deadtime

Global LDAP server deadtime period in seconds

i0

LDAP server deadtime period in minutes (default 0 mins -disabled)

Command Mode

  • /exec/configure

ldap-server host

[no] ldap-server host { <hostipname> } [ { enable-ssl | port <i1> [ timeout <i2> ] | rootDN <s0> [ password { 7 <s1> | <s2> } ] [ port1 <i3> ] [ timeout1 <i4> ] | timeout2 <i5> | referral-disable } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

host

LDAP server's DNS name or IP address

hostipname

IPV4/IPV6 address or DNS name

enable-ssl

(Optional) LDAP server enable ssl

port

(Optional) LDAP server's port (default: global config)

i1

(Optional) port number

timeout

(Optional) LDAP server timeout period in seconds

i2

(Optional) LDAP server timeout in seconds (default: global config)

rootDN

(Optional) LDAP server root DN

s0

(Optional) root DN

password

(Optional) LDAP server root password

7

(Optional) LDAP root password (encrypted)

s1

(Optional) password (encrypted)

s2

(Optional) password (clear text)

port1

(Optional) LDAP server's port (default: global config)

i3

(Optional) port number

timeout1

(Optional) LDAP server timeout period in seconds

i4

(Optional) LDAP server timeout in seconds (default: global config)

timeout2

(Optional) LDAP server timeout period in seconds

i5

(Optional) LDAP server timeout in seconds (default: global config)

referral-disable

(Optional) LDAP server disable referrals

Command Mode

  • /exec/configure

ldap-server host test rootDN

[no] ldap-server host { <hostipname> } test rootDN <r1> { { [ username <s0> { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] | [ idle-time <i1> ] } ] } | { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] } | { [ idle-time <i1> ] } }

Syntax Description

username

(Optional) <s0>

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

host

LDAP server's IP address

hostipname

IPV4/IPV6 address or DNS name

test

Parameters to send test packets

7

(Optional) LDAP test password (encrypted)

s0

(Optional) user name

password

(Optional) user password in test packets

s1

(Optional) test password

s2

(Optional) test password (encrypted)

rootDN

rootDN in test packets

r1

root DN

idle-time

(Optional) time interval for monitoring the server

i1

(Optional) time period in minutes

Command Mode

  • /exec/configure

ldap-server timeout

[no] ldap-server timeout <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

timeout

Global LDAP server timeout period in seconds

i0

LDAP server timeout period in seconds (default 5 sec)

Command Mode

  • /exec/configure

ldap search-map

[no] ldap search-map <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap

Configure information about ldap

search-map

Configure the search-map

s0

Search Map Name

Command Mode

  • /exec/configure

less

| less [ -d | -E ] +

Syntax Description

|

Pipe command output to filter

less

Filter for paging

-d

(Optional) dumb terminal

-E

(Optional) quit at end of file

Command Mode

  • /output

license smart clear eventlog

license smart clear eventlog

Syntax Description

license

License related command

smart

Smart license related commands

clear

Clear

eventlog

Event log

Command Mode

  • /exec

license smart custom_id

license smart custom_id <s0> | no license smart custom_id

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

custom_id

Identifier to be added in utility RUM Report.

s0

Provide identifier

Command Mode

  • /exec/configure

license smart factory reset

license smart factory reset

Syntax Description

license

License related command

smart

Smart license related commands

factory

Smart license factory command

reset

Reset smart command

Command Mode

  • /exec

license smart import

license smart import <file>

Syntax Description

license

License related command

smart

Smart license related commands

import

Import or install authorization codes, policies, trust codes or ack from file

file

Specify URL for the file

Command Mode

  • /exec

license smart privacy

[no] license smart privacy { all | hostname | version }

Syntax Description

no

(Optional) Negate a command or set its defaults

license

License related command

smart

Smart license related commands

privacy

Set internal data privacy

hostname

Apply privacy setting for hostname

version

Apply privacy setting for SA version

all

Apply privacy setting for all data types

Command Mode

  • /exec/configure

license smart proxy address

license smart proxy { address <proxyadd> | port <proxyport> } | no license smart proxy { address | port }

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

proxy

Proxy related commands

address

The IP address or the hostname

proxyadd

Address/Hostname

port

The port

proxyport

Proxy port

Command Mode

  • /exec/configure

license smart save

license smart save { usage { all | days <n> | unreported | rum-Id <rum_id> } <file> | trust-request <file> }

Syntax Description

license

License related command

smart

Smart license related commands

save

Save RUM reports / trust request to a file offline

usage

Save RUM reports

all

Save all RUM reports

days

Save RUM reports for the last number of <days> specified

unreported

Save RUM reports not previously saved in file or sent

rum-Id

Save an individual RUM report

rum_id

RUM ID

trust-request

Generate trust request to save it a file

n

Specify number of days

file

Specify URL for the file

Command Mode

  • /exec

license smart source-interface

license smart source-interface <src-intf> | no license smart source-interface

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

source-interface

Select source interface

src-intf

Specify interface

Command Mode

  • /exec/configure

license smart sync local

license smart sync { local | all }

Syntax Description

license

License related command

smart

Smart license related commands

sync

Send any unsent RUM reports to the CSLU, controller REST endpoint or CSSM

local

Get codes for the current UDI

all

Get codes for all devices in HA config

Command Mode

  • /exec

license smart transport

license smart transport { callhome | smart | cslu | off } | no license smart transport

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

transport

set transport mode

callhome

Set the transport mode to callhome

smart

Set the transport mode to smart

cslu

Set the transport mode to cslu

off

Set the transport mode to off

Command Mode

  • /exec/configure

license smart trust idtoken local

license smart trust idtoken <s0> { local | all } [ force ]

Syntax Description

license

License related command

smart

Smart license related commands

trust

Establish trust with backend

idtoken

Use Trust Token to establish trust

s0

Provide id token received from backend

local

Establish trust with backend for Active SUP

all

Establish trust with backend for all SUPs

force

(Optional) Force backend to re-establish trust

Command Mode

  • /exec

license smart url smart

license smart url { smart | cslu } <url> | no license smart url { smart | cslu }

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related command

url

Set the transport url

smart

Set smart transport url

cslu

Set CSLU URL

url

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL

Command Mode

  • /exec/configure

license smart usage interval

license smart usage interval <i0> | no license smart usage interval

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

usage

RUM reports

interval

Day for periodic RUM reports sending

i0

Reporting interval in days. Default 30 days

Command Mode

  • /exec/configure

license smart vrf

license smart vrf { <vrf_name> | <vrf-known-name> } | no license smart vrf

Syntax Description

no

Negate a command or set its defaults

license

License related command

smart

Smart license related commands

vrf

Configure vrf name

vrf_name

VRF name

vrf-known-name

Known VRF name

Command Mode

  • /exec/configure

limit-resource module-type

{ limit-resource module-type <card-type> + } | { no limit-resource module-type }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

module-type

Controls which type of modules are allowed in this vdc

card-type

Allowed module types

Command Mode

  • /exec/configure/vdc

limit-resource monitor-session-erspan-dst minimum maximum equal-to-min

{ limit-resource monitor-session-erspan-dst minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-erspan-dst [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session-erspan-dst

Monitor erspan destination session

minimum

minimum monitor erspan-dst session to allocate

min-val

minimum monitor erspan-dst session value

maximum

maximum monitor erspan-dst session to allocate

max-val

maximum monitor erspan-dst session value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session-inband-src minimum maximum equal-to-min

{ limit-resource monitor-session-inband-src minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-inband-src [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session-inband-src

Monitor inband source

minimum

minimum monitor inband source to allocate

min-val

minimum monitor inband source value

maximum

maximum monitor inband source to allocate

max-val

maximum monitor inband source value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session minimum maximum equal-to-min

{ limit-resource monitor-session minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session

Monitor local/erspan-source session

minimum

minimum monitor local session to allocate

min-val

minimum monitor local session value

maximum

maximum monitor local session to allocate

max-val

maximum monitor local session value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource port-channel minimum maximum

limit-resource port-channel minimum <min-val> maximum { <max-val> | equal-to-min } | no limit-resource port-channel [ minimum <min-val> maximum { <max-val> | equal-to-min } ]

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

port-channel

set port-channel limits

minimum

minimum port-channels to allocate

min-val

maximum

maximum port-channels to allocate

max-val

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource vlan minimum maximum equal-to-min

{ limit-resource vlan minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource vlan [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

vlan

set VLAN limits

minimum

minimum VLANs to allocate

min-val

minimum VLANs value

maximum

maximum VLANs to allocate

max-val

maximum VLANs value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource vrf minimum maximum equal-to-min

{ limit-resource vrf minimum <number1> maximum { <number2> | equal-to-min } } | { no limit-resource vrf [ minimum <number1> maximum { <number2> | equal-to-min } ] }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

vrf

set vrf resource limits

minimum

minimum vrf resources to allocate

number1

minimum vrf resource value

maximum

maximum vrf resources to allocate

number2

maximum vrf resource value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit address-count

[no] limit address-count <addr_count>

Syntax Description

no

(Optional) Negate a command or set its defaults

addr_count

maximum value

Command Mode

  • /exec/configure/config-snoop-policy

line console

[no] line console

Syntax Description

no

(Optional) Negate a command or set its defaults

line

Configure a terminal line

console

Primary terminal line

Command Mode

  • /exec/configure

line console

[no] line console

Syntax Description

no

(Optional) Negate a command or set its defaults

line

Configure a terminal line

console

Primary terminal line

Command Mode

  • /exec/configure

line vty

line vty

Syntax Description

line

Configure a terminal line

vty

Virtual terminal line

Command Mode

  • /exec/configure

link-flap error-disable count interval

{ link-flap error-disable count <count> interval <interval> | no link-flap error-disable }

Syntax Description

no

Negate a command or set its defaults

link-flap

Configure actions on link-flap

error-disable

Configure the port to error-disable on link-flap

count

Configure the number of link-flaps to trigger the action

count

Specify the number of link-flaps for action

interval

Configure the interval to trigger the action

interval

link-flap interval in seconds

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link-level-flow-control watch-dog-interval on

[no] link-level-flow-control watch-dog-interval { on | off }

Syntax Description

no

(Optional) Negate the command

link-level-flow-control

Enable/Disable LLFC

watch-dog-interval

Watch dog interval

on

Enable LLFC watch-dog interval globally

off

Disable LLFC watch-dog interval globally

Command Mode

  • /exec/configure

link-state-trap

[no] link-state-trap

Syntax Description

no

(Optional) Negate a command or set its defaults

link-state-trap

Enable/disable link state change traps

Command Mode

  • /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-fcip /exec/configure/if-iscsi

link active-jitter-management

{ link active-jitter-management | no link active-jitter-management }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

active-jitter-management

Enable/Disable jitter management on link

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link debounce

link debounce { [ link-up [ time <time_val_link_up> ] ] | [ time <time_val> ] } | no link debounce [ link-up ]

Syntax Description

no

Negate a command or set its defaults

link

Configure link

debounce

Configure link debounce timer

link-up

(Optional) Timer for the link-up event

time

(Optional) Link debounce time

time_val

(Optional) Timer value (in milliseconds)

time_val_link_up

(Optional) Timer value (in milliseconds)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link dfe adaptive-tuning

{ link dfe adaptive-tuning | no link dfe adaptive-tuning }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

dfe

Decision Feedback Equalizer

adaptive-tuning

Configure DFE adaptive tuning for interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link loopback

{ link loopback | no link loopback }

Syntax Description

no

Negate a command or set its defaults

link

configure link

loopback

configure the port to be in a loopback mode

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link mac-up timer

{ link mac-up timer <mac_up_timer_val> | no link mac-up timer }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

mac-up

Configure link mac-up timer

timer

Link mac-up time

mac_up_timer_val

Timer value (in seconds)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link max-bringup timer

{ link max-bringup timer <max_bringup_timer_val_max> | no link max-bringup timer }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

max-bringup

Configure link max-bringup timer maximum

timer

Link max-bringup timer maximum

max_bringup_timer_val_max

Timer value (in seconds)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link transmit attenuation

{ link transmit attenuation | no link transmit attenuation }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

transmit

Configure link transmit for interface

attenuation

Enable/Disable attenuation on link transmit

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link transmit reset-skip

{ link transmit reset-skip | no link transmit reset-skip }

Syntax Description

no

Negate a command or set its defaults

link

Configure link

transmit

Configure link transmit for interface

reset-skip

Configure link transmit for interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

lisp

{ lisp-lig | lig } { version | self | self6 | <hostname> | { <eid> | <eid6> } } [ source { <seid> | <seid6> } ] [ to { <mr-hostname> | { <mr> | <mr6> } } ] [ count <count> ] [ probe ] [ vrf { <vrf-name> | <vrf-known-name> } ]

Syntax Description

lisp-lig

LISP Internet Groper

lig

LISP Internet Groper

eid

LIG on a IPv4 Endpoint ID (EID)

version

Display Internet Draft version lig supports

self

Test if IPv4 EID-prefix registered in mapping database

self6

Test if IPv6 EID-prefix registered in mapping database

hostname

DNS name for Endpoint ID (EID)

source

(Optional) Provide source EID for Map-Request

seid

(Optional) Source IPv4 Endpoint ID (EID)

to

(Optional) Where to send the Map-Request

mr-hostname

(Optional) DNS name for Map-Resolver

mr

(Optional) Map-Resolver IPv4 address to send Map-Request to

count

(Optional) Map-Requests to send before Map-Reply returned

count

(Optional) Number of Map-Requests

probe

(Optional) RLOC-probe each locator

vrf

(Optional) LIGing for specific VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec

lisp ddt

{ [ no ] lisp ddt }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

ddt

Configures a LISP-DDT mapping system functionality

Command Mode

  • /exec/configure /exec/configure/vrf

lisp ddt authoritative-prefix eid-prefix

{ [ no ] lisp ddt authoritative-prefix eid-prefix { <eid-prefix> | <eid-prefix6> } } | { [ no ] lisp ddt authoritative-prefix instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] } | { [ no ] lisp ddt authoritative-prefix <star> } | { [ no ] lisp ddt authoritative-prefix instance-id { <iidp> | <range> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

ddt

Configure LISP-DDT parameters

authoritative-prefix

Configure EID-prefix this LISP-DDT node is authoritative for

instance-id

Instance ID of VPN for EID-prefix

iid

Instance-ID value

star

Authoritative prefix on root for all address space

iidp

Instance-ID in prefix format

range

Instance-ID range in 'x-y' format where y > x

eid-prefix

Authoritative IPv4 or IPv6 EID-prefix

eid-prefix

EID-prefix in IPv4 slash format

Command Mode

  • /exec/configure /exec/configure/vrf

lisp ddt delegate eid-prefix

{ [ no ] lisp ddt delegate { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> | <node6> } instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> | <node6> } instance-id { <iidp> | <range> } [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

ddt

Configure LISP-DDT parameters

delegate

Configure LISP-DDT child in delegation hierarchy

node

IPv4 locator address of DDT node

instance-id

Instance ID of VPN for EID-prefix

iid

Instance-ID value

iidp

Instance-ID in prefix format

range

Instance-ID range in 'x-y' format where y > x

eid-prefix

Child delegration for IPv4 or IPv6 EID-prefix

eid-prefix

EID-prefix in IPv4 slash format

priority

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

priority

(Optional) Lower priority Locator takes preference

weight

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

weight

(Optional) Specified in a percentage from 0 to 100

map-server

(Optional) Child delegate is a Map-Server

public-key

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

key

(Optional) RSA public-key

Command Mode

  • /exec/configure /exec/configure/vrf

lisp ddt map-server-peer eid-prefix

{ [ no ] lisp ddt map-server-peer { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority <priority> weight <weight> ] [ public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6> } instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority> weight <weight> ] [ public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6> } instance-id { <iidp> | <range> } [ priority <priority> weight <weight> ] [ public-key <key> ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

ddt

Configure LISP-DDT parameters

map-server-peer

Configure other map-server peers

node

IPv4 locator address of DDT node

instance-id

Instance ID of VPN for EID-prefix

iid

Instance-ID value

iidp

Instance-ID in prefix format

range

Instance-ID range in 'x-y' format where y > x

eid-prefix

Child delegration for IPv4 or IPv6 EID-prefix

eid-prefix

EID-prefix in IPv4 slash format

priority

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

priority

(Optional) Lower priority Locator takes preference

weight

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

weight

(Optional) Specified in a percentage from 0 to 100

public-key

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

key

(Optional) RSA public-key

Command Mode

  • /exec/configure /exec/configure/vrf

lisp ddt root

[no] lisp ddt root { <root> | <root6> } [ public-key <key> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

ddt

Configure LISP-DDT parameters

root

Configure LISP-DDT root of tree in Map-Resolver

root

IPv4 locator address of DDT root

public-key

(Optional) DDT root's public key used to verify signed Map-Referrals

key

(Optional) RSA public-key

Command Mode

  • /exec/configure /exec/configure/vrf

lisp dynamic-eid

{ [ no ] lisp dynamic-eid <dyn-eid-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

dynamic-eid

Configure dynamic-EIDs for roaming

dyn-eid-name

Name your dynamic-EID

Command Mode

  • /exec/configure

lisp dynamic-eid

{ [ no ] lisp dynamic-eid <dyn-eid-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

dynamic-eid

Configure dynamic-EIDs for roaming

dyn-eid-name

Name your dynamic-EID

Command Mode

  • /exec/configure/vrf

lisp explicit-locator-path

[no] lisp explicit-locator-path <elp-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

explicit-locator-path

Configures a LISP Explicit Locator Path (ELP)

elp-name

Name of LISP ELP

Command Mode

  • /exec/configure/vrf

lisp explicit-locator-path

{ [ no ] lisp explicit-locator-path <elp-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

explicit-locator-path

Configures a LISP Explicit Locator Path (ELP)

elp-name

Name of LISP ELP

Command Mode

  • /exec/configure

lisp extended-subnet-mode

{ [ no ] lisp extended-subnet-mode }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP interface configuration commands

extended-subnet-mode

Create dynamic-EID state when EIDs reside on their home subnet

Command Mode

  • /exec/configure/if-igp

lisp geo-coordinates

[no] lisp geo-coordinates <latitude> <longitude> [ <altitude> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

geo-coordinates

Configure Geo Coordinates for this router

latitude

Latitude in DMS format: 'degree-min-sec-N' or 'degree-min-sec-S

longitude

Longitude in DMS format: 'degree-min-sec-E' or 'degree-min-sec-W format

altitude

(Optional) Altitude in meters above sea-level

Command Mode

  • /exec/configure /exec/configure/vrf

lisp instance-id

[no] lisp instance-id <iid>

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

instance-id

Configures Instance-ID for global data-mappings

iid

24-bit instance-ID value

Command Mode

  • /exec/configure /exec/configure/vrf

lisp loc-reach-algorithm

[no] lisp loc-reach-algorithm { count-tcp | echo-nonce | { rloc-probing [ map-request-on-failure ] } }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

loc-reach-algorithm

Configure locator reachability algorithm

count-tcp

Count TCP SYNs and ACKs

echo-nonce

Request for nonce to echo back in data-plane

rloc-probing

Probe each high-priority RLOC with Map-Request as last resort

map-request-on-failure

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure /exec/configure/vrf

lisp merge-registrations site-id

[no] lisp merge-registrations site-id <site-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

merge-registrations

ETRs merge registrations from Map-Notify messages

site-id

Configure site-id value for each xTR at site

site-id

Site-ID to group xTRs together

Command Mode

  • /exec/configure /exec/configure/vrf

lisp mobility

[no] lisp mobility <dyn-eid-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP interface configuration commands

mobility

Configures to allow EID mobility on interface

dyn-eid-name

Name of the dynamic-EID to use

Command Mode

  • /exec/configure/if-igp

lisp mobility test-liveness

[no] lisp mobility test-liveness

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP interface configuration commands

mobility

Configures to allow EID mobility on interface

test-liveness

Ping discovered dyn-eid hosts on this interface periodically to determine host liveness

Command Mode

  • /exec/configure/if-igp

lisp security

[no] lisp security [ strong ]

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

security

Configure LISP-SEC on ITR or PITR

strong

(Optional) Reject Map-Replies without LISP-SEC signatures included

Command Mode

  • /exec/configure /exec/configure/vrf

lisp site

{ [ no ] lisp site <site-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

site

Configures LISP sites in a map-server

site-name

Name your LISP site

Command Mode

  • /exec/configure/vrf

lisp site

{ [ no ] lisp site <site-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

site

Configures LISP sites in a map-server

site-name

Name your LISP site

Command Mode

  • /exec/configure

lisp smr-locators

[no] lisp smr-locators

Syntax Description

no

(Optional) Negate a command or set its defaults

lisp

LISP global configuration commands

smr-locators

Send SMR to all RLOCs in locator-set for map-cache entry

Command Mode

  • /exec/configure

lisp to

{ lisp-rig | rig } [ instance-id <iid> ] { <hostname> | { <eid> | <eid6> } } to { <ddt-hostname> | { <ddt> | <ddt6> } }

Syntax Description

lisp-rig

LISP-DDT Referral Internet Groper

rig

LISP-DDT Referral Internet Groper

instance-id

(Optional) Instance-ID of VPN EID resides in

iid

(Optional) 24-bit instance-ID value

eid

RIG on a IPv4 Endpoint ID (EID)

hostname

DNS name for Endpoint ID (EID)

to

Where to send the Map-Request

ddt-hostname

DNS name for DDT-node

ddt

DDT-node IPv4 address to send Map-Request to

Command Mode

  • /exec

listobject-boolean not

listobject-boolean <obj-id> not

Syntax Description

listobject-boolean

Configure Object as member of tracking list

obj-id

Tracked object

not

Negate Up status

Command Mode

  • /exec/configure/tr-list-bool

listobject-weight weight threshold-weight

listobject-weight { <obj-id> weight <weight-val> } | threshold-weight { weight-thresh { weightup <up-weight> [ weightdown <down-weight> ] | weightdown <down-weight> [ weightup <up-weight> ] } } | no threshold-weight weight-thresh

Syntax Description

no

Negate a command or set its defaults

listobject-weight

Configure Object as member of tracking list

obj-id

Tracked Object

weight

Assign a weight to object

weight-val

Assign a weight to object

threshold-weight

Threshold parameters

weight-thresh

Weight threshold

weightup

Up threshold

up-weight

Up threshold weight

weightdown

(Optional) Down threshold

down-weight

(Optional) Down threshold weight

Command Mode

  • /exec/configure/tr-list-thrw

listobject

[no] listobject <obj-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

listobject

Configure Object as member of tracking list

obj-id

Tracked Object

Command Mode

  • /exec/configure/tr-list-thrw /exec/configure/tr-list-thrp /exec/configure/tr-list-bool

liveness-detection

[no] liveness-detection

Syntax Description

no

(Optional) Negate a command or set its defaults

liveness-detection

Configure Traffic Engineering Segment Routing liveness detection related configurations

Command Mode

  • /exec/configure/sr/te

liveness-detection

[no] liveness-detection

Syntax Description

no

(Optional) Negate a command or set its defaults

liveness-detection

Configure color specific liveness detection related configurations

Command Mode

  • /exec/configure/sr/te/color

liveness-detection

[no] liveness-detection

Syntax Description

no

(Optional) Negate a command or set its defaults

liveness-detection

Configure color specific liveness detection related configurations

Command Mode

  • /exec/configure/sr/te/pol

lldp

[no] lldp { holdtime <i0> | reinit <i1> | timer <i2> | portid-subtype <i3> | tlv-select { management-address | port-description | port-vlan | power-management | system-capabilities | system-description | system-name | dcbxp | four-wire-power-management | port { max-framesize | vlan-name | link-aggregation } } | port-channel | multi-neighbor | chassis-id switch }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure global LLDP parameters

holdtime

Specify the holdtime (in sec) to be sent in packets

i0

holdtime in sec

reinit

Delay (in sec) for LLDP initialisation on any interface

i1

reinit in sec

timer

Specify the rate at which LLDP packets are sent (in sec)

i2

rate of packets in sec

portid-subtype

config portid subtype for LLDP TLV and SNMP MIBs

i3

0: long interface name (default), 1: short interface name

tlv-select

Selection of LLDP to send

management-address

Management Address TLV

port-description

Port Description TLV

port-vlan

Port Vlan ID TLV

power-management

IEEE 802.3 DTE Power via MDI TLV

system-capabilities

System Capabilities TLV

system-description

System Description TLV

system-name

System Name TLV

dcbxp

DCBXP TLVs

four-wire-power-management

Cisco 4-wire Power via MDI TLV

port

Organization specific port TLVs

max-framesize

Port Maximum Frame Size TLV

vlan-name

Port Vlan Name TLV

link-aggregation

Port Link Aggregation TLV

port-channel

Enable LLDP on Port-channel

multi-neighbor

Enable multiple LLDP neighbors per interface

chassis-id

Device ID to advertise (Default is MAC of the port)

switch

Advertise MAC of the switch

Command Mode

  • /exec/configure

lldp dcbx version auto

lldp dcbx version auto

Syntax Description

lldp

Configure LLDP parameters

dcbx

Configure DCBX parameters

version

Change the DCBX protocol version

auto

Auto-detect the DCBX version

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp dcbx version cee

[no] lldp dcbx version { cee | ieee }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure LLDP parameters

dcbx

Configure DCBX parameters

version

Change the DCBX protocol version

cee

The CEE version of DCBX

ieee

The IEEE 802.1 version of DCBX

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp receive

[no] lldp receive

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

receive

Enable LLDP reception on interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether /exec/configure/if-vethernet /exec/configure/if-veth-any /exec/configure/if-veth-all /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-switch

lldp tlv-select dcbxp egress

[no] lldp tlv-select dcbxp { egress-queuing }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure global LLDP parameters

tlv-select

Selection of LLDP to send

dcbxp

DCBXP TLVs

egress-queuing

DCBXP TLV egress queuing

Command Mode

  • /exec/configure

lldp tlv-select management-address v4

[no] lldp tlv-select management-address { v4 | v6 }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure global LLDP parameters

tlv-select

Selection of LLDP to send

management-address

Management Address TLV

v4

Management Address TLV v4

v6

Management Address TLV v6

Command Mode

  • /exec/configure

lldp tlv-set management-address

[no] lldp tlv-set management-address <ip-addr>

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

management-address

Management address to be sent in management-tlv of LLDPDU.

ip-addr

IP address in dotted decimal format i.i.i.i

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set management-address ipv6

[no] lldp tlv-set management-address <ipv6-addr> ipv6

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

management-address

Management address to be sent in management-tlv of LLDPDU.

ipv6

IPV6

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set vlan

[no] lldp tlv-set vlan [ <vlan-id> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

vlan

VLAN-id whose SVI IP address should be used as management adrress in management-tlv of LLDPDU. Default is native VLAN.

vlan-id

(Optional) vlan-id within range of 1-4094

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp transmit

[no] lldp transmit

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

transmit

Enable LLDP transmission on interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether /exec/configure/if-vethernet /exec/configure/if-veth-any /exec/configure/if-veth-all /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-switch

load-balance

[no] load-balance { { { method <lb-method> } | { buckets <buckets> } | { mask-position <mpos> } } + }

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

Loadbalance options for this match

method

Loadbalance method

lb-method

Loadbalance method options

buckets

Buckets for traffic distribution - this should be in powers of 2

buckets

Loadbalance bucket count

mask-position

Loadbalance mask position

mpos

Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6

Command Mode

  • /exec/configure/epbr-policy/action

load-balance

[no] load-balance { { { method <lb-method> } | { buckets <buckets> } | { mask-position <mpos> } } + }

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

Loadbalance options for this match

method

Loadbalance method

lb-method

Loadbalance method options

buckets

Buckets for traffic distribution - this should be in powers of 2

buckets

Loadbalance bucket count

mask-position

Loadbalance mask position

mpos

Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6

Command Mode

  • /exec/configure/epbr-sess-policy/action

load-balance

[no] load-balance { { method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | { buckets <num> } | { mask-position <mask> } | { least-bit } } + }

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

ITD Loadbalance

method

ITD Loadbalance method

src

Source based parameters

dst

Destination based parameters

ip

IP

ip-l4port

IP and L4 port

src-protocol

Protocol

range

Match only packets in the range of port numbers

src-x

src-y

ip-dst

IP

dst-protocol

Protocol

dst-x

dst-y

buckets

Used to create the buckets for traffic distribution, and it should be in powers of 2

num

Loadbalance bucket number

mask-position

Loadbalance mask position

mask

Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6

least-bit

Craft load-balancing masks beginning at the least significant bits

Command Mode

  • /exec/configure/itd

load-balance egress filter-policy route-map

[no] load-balance egress filter-policy route-map <rmap-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

Enable load-balance functionality applied to routes in the underlay

egress

Enable load-balance functionality during egress to routes in the underlay

filter-policy

Restricting the egress load-balance logic to specific routes matching the route-map

route-map

Apply route-map to filter the routes

rmap-name

Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6

load-balance egress multipath auto-policy route-map

[no] load-balance egress multipath auto-policy route-map <rmap-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

Enable load-balancing functionality applied to routes in the underlay (default VRF)

egress

Enable load-balance functionality during egress to routes in the underlay

multipath

Apply multipath rules to specific routes

auto-policy

Apply auto multipath rules to specific routes

route-map

Apply route-map auto multipath rules to specific routes

rmap-name

Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-af-ipv6

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-vlan-common

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

counter

Specify counter for this load interval

interval

Load interval delay in seconds

counter_val

Specify counter for this load interval

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-vlan-common

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

counter

Specify counter for this load interval

counter_val

Specify counter for this load interval

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load

load <uri0> [ <s0> ]

Syntax Description

load

Load system image

uri0

Enter image URI

s0

(Optional) Options

Command Mode

  • /exec

load

load <uri0>

Syntax Description

load

Load system image

uri0

Enter image URI

Command Mode

  • /exec

load

load <uri0> [ <s0> ]

Syntax Description

load

Load system image

uri0

Enter image URI

s0

(Optional) Options

Command Mode

  • /exec

load configuration failed commit

load configuration failed commit

Syntax Description

load

Load the configuration

configuration

Contents of configuration

failed

Load failed configuration

commit

Failed configuration from last commit

Command Mode

  • /exec/configure

local-as

{ local-as <asn> [ no-prepend [ replace-as [ dual-as ] ] ] } | { { no | default } local-as [ <asn> ] }

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

local-as

Specify the local-as number for the eBGP neighbor

asn

Autonomous System Number

no-prepend

(Optional) Do not prepend the local-as number to updates from the eBGP neighbor

replace-as

(Optional) Prepend only the local-as number to updates to eBGP neighbor

dual-as

(Optional) Connect using either the local-as number or the real as

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

local-as

local-as <asn> | no local-as [ <asn> ]

Syntax Description

no

Negate a command or set its defaults

local-as

Specify the local-as for this vrf

asn

AS number

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <prefix> <mask> | <prefix-mask> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

local-label

Configure local label assignment and forwarding

static-inlabel

Label Value

prefix

For a given prefix

prefix

Destination prefix

mask

Destination prefix mask

prefix-mask

Destination prefix/mask

Command Mode

  • /exec/configure/mpls_static/ipv4

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <ipv6-prefix-mask> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

local-label

Configure local label assignment and forwarding

static-inlabel

Label Value

prefix

For a given prefix

Command Mode

  • /exec/configure/mpls_static/ipv6

locator-led

[no] locator-led { chassis | module <module> | fan <fan_num> | powersupply <psnum> }

Syntax Description

no

(Optional) Negate a command or set its defaults

locator-led

blink locator led on device

chassis

blink chassis led

module

blink module led

module

please enter the module number

fan

blink Fan led

fan_num

fan number

powersupply

blink powersupply led

psnum

powersupply number

Command Mode

  • /exec

locator

[no] locator <locator-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

locator

Configure Traffic Engineering Segment Routing V6 locator

locator-name

Configure locator name

Command Mode

  • /exec/configure/sr/te/sr/srv6/locs

locator

[no] locator <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

locator

Configure an SRv6 locator for this node

name

Name for the locator

Command Mode

  • /exec/configure/sr/srv6/locators

locator

[no] locator <locator-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

locator

Configure SRv6 locator name

locator-name

Locator name to advertise

Command Mode

  • /exec/configure/router-isis/router-isis-af-ipv6/srv6

locator

[no] locator <locator-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

locator

Specify the locator

locator-name

Locator name

Command Mode

  • /exec/configure/router-bgp/router-bgp-srv6

locators

[no] locators

Syntax Description

no

(Optional) Negate a command or set its defaults

locators

Base to configure SRv6 locators

Command Mode

  • /exec/configure/sr/srv6

locators

[no] locators

Syntax Description

no

(Optional) Negate a command or set its defaults

locators

Configure Traffic Engineering Segment Routing V6 locator configurations

Command Mode

  • /exec/configure/sr/te/sr/srv6

lockdown

[no] lockdown

Syntax Description

no

(Optional) Negate a command or set its defaults

lockdown

Disable re-optimization of the path preferences for this policy

Command Mode

  • /exec/configure/sr/te/pol

lockdown

[no] lockdown

Syntax Description

no

(Optional) Negate a command or set its defaults

lockdown

Disable re-optimization of the path preferences for policies using this color template

Command Mode

  • /exec/configure/sr/te/color

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/l2mp-isis/l2mp-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

detail

(Optional) Notify all state changes

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

detail

(Optional) Notify all state changes

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

log-neighbor-changes

[no] log-neighbor-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-neighbor-changes

Log a message for neighbor up/down event

Command Mode

  • /exec/configure/router-bgp/vrf-cmds

log-neighbor-changes

[ no | default ] log-neighbor-changes [ disable ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

log-neighbor-changes

Log message for neighbor up/down event

disable

(Optional) Disable logging of neighbor up/down event

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

log-neighbor-warnings

{ { [ eigrp ] log-neighbor-warnings [ <interval> ] } | { no [ eigrp ] log-neighbor-warnings [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

eigrp

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

log-neighbor-warnings

Enable/Disable IP-EIGRP neighbor warnings

interval

(Optional) Neighbor warning interval in seconds

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

logging

[no] logging { neighbor-changes |

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Enable LDP logging

neighbor-changes

Log LDP neighbor state changes

Command Mode

  • /exec/configure/ldp

logging abort

logging abort

Syntax Description

logging

Modify message logging facilities

abort

Flushes cached data without committing and releases the lock

Command Mode

  • /exec/configure

logging console

[no] logging console [ <i0> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

console

Set console logging

i0

(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging distribute

[no] logging distribute

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

distribute

Enables/disables fabric distribution using cfs.

Command Mode

  • /exec/configure

logging drop threshold

[no] logging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level <level-value> ]

Syntax Description

no

Negate a command or set its defaults

logging

set logging for copp class

drop

logging for copp drops

threshold-packets

threshold value for dropped packets

threshold-bytes

threshold value for dropped bytes

level

(Optional) syslog level

level-value

(Optional) specify the logging level between 1-7

Command Mode

  • /exec/configure/pmap/class

logging drop threshold

logging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level <level-value> ]

Syntax Description

logging

set logging for copp class

drop

logging for copp drops

threshold-packets

threshold value for dropped packets

threshold-bytes

threshold value for dropped bytes

level

(Optional) syslog level

level-value

(Optional) specify the logging level between 1-7

Command Mode

  • /exec/configure/pmap/class

logging event link enable

[no] logging event { link-status | trunk-status } { enable | default }

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

link-status

UPDOWN and CHANGE messages

trunk-status

TRUNK status messages

enable

To enable logging overriding port level configuration

default

default logging configuration used by interfaces not explicitly configured

Command Mode

  • /exec/configure

logging event port link-status

logging event port link-status [ default ] | no logging event port link-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

default

(Optional) Use the global default value

Command Mode

  • /exec/configure/if-loopback

logging event port link-status

logging event port link-status

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status

[no] logging event port link-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status default

logging event port link-status default

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

default

Use the global default value

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-switch /exec/configure/if-port-channel-sub-switch /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port trunk-status

[no] logging event port trunk-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

logging event port trunk-status

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status default

logging event port trunk-status default

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

default

Use the global default value

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging history

{ logging history { <i0> | size <i1> } | no logging history [ size ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

history

Modifies severity level or size for history table

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

size

Modifies history table size

i1

Enter history table size

Command Mode

  • /exec/configure

logging level

[no] logging level { xml server | xmlma } <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

xml

xml agent

server

xml agent server

xmlma

xml master agent. Same as combination of keywords xml server

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

[no] logging level { { routing ipv6 multicast } | m6rib } <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

routing

Configure routing information

ipv6

Display IPv6 information

multicast

Set syslog filter level for M6RIB

m6rib

Set syslog filter level for M6RIB

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

{ logging level { auth <i1> | authpriv <i2> | cron <i3> | daemon <i4> | ftp <i5> | kernel <i6> | local0 <i7> | local1 <i8> | local2 <i9> | local3 <i10> | local4 <i11> | local5 <i12> | local6 <i13> | local7 <i14> | lpr <i15> | mail <i16> | news <i17> | syslog <i18> | user <i19> | uucp <i20> } | no logging level { auth [ <i1> ] | authpriv [ <i2> ] | cron [ <i3> ] | daemon [ <i4> ] | ftp [ <i5> ] | kernel [ <i6> ] | local0 [ <i7> ] | local1 [ <i8> ] | local2 [ <i9> ] | local3 [ <i10> ] | local4 [ <i11> ] | local5 [ <i12> ] | local6 [ <i13> ] | local7 [ <i14> ] | lpr [ <i15> ] | mail [ <i16> ] | news [ <i17> ] | syslog [ <i18> ] | user [ <i19> ] | uucp [ <i20> ] } }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

auth

Set level for Authorization System

i1

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

authpriv

Set level for Authorization (Private) system

i2

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

cron

Set level for Cron/at facility

i3

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

daemon

Set level for System daemons

i4

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

ftp

Set level for File Transfer System

i5

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

kernel

Set level for kernel

i6

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local0

Set level for Local use daemons

i7

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local1

Set level for Local use daemons

i8

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local2

Set level for Local use daemons

i9

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local3

Set level for Local use daemons

i10

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local4

Set level for Local use daemons

i11

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local5

Set level for Local use daemons

i12

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local6

Set level for Local use daemons

i13

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local7

Set level for Local use daemons

i14

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

lpr

Set level for Line Printer System

i15

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

mail

Set level for Mail system

i16

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

news

Set level for USENET news

i17

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

syslog

Set level for Internal Syslog Messages

i18

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

user

Set level for User Process

i19

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

uucp

Set level for Unix-to-Unix copy system

i20

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

[no] logging level { { routing [ ip | ipv4 ] multicast } | mrib } <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

routing

Configure routing information

ip

(Optional) Configure IP features

ipv4

(Optional) Configure IP features

multicast

Set syslog filter level for MRIB

mrib

Set syslog filter level for MRIB

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level aaa

logging level aaa <i0> | no logging level aaa [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

aaa

Set level for aaa syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level acl

[no] logging level acl <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

acl

Set syslog filter level for acl manager

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level aclmgr

[no] logging level aclmgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

aclmgr

Set level for aclmgr syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level adbm

[no] logging level adbm <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

adbm

Set level for adbm syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level adjmgr

[no] logging level adjmgr <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

adjmgr

Set syslog filter level for Adjacency Manager

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level all

{ logging level { all <i0> } | no logging level { all [ <i0> ] } }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

all

Set level for all facilities

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level amt

[no] logging level amt <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

amt

Set syslog filter level for AMT

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level app-hosting

[no] logging level app-hosting <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

app-hosting

Set level for app-hosting syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level arp

{ logging level arp <level> } | { no logging level arp [ <level> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

arp

Set syslog filter level for ARP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ascii-cfg

[no] logging level ascii-cfg <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ascii-cfg

Set logging level for ascii-cfg

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level assoc_mgr

[no] logging level assoc_mgr <i0> | no logging level assoc_mgr [ <i0> ]

Syntax Description

no

(Optional) Negate a command or set its default

logging

Show logging configuration and contents of logfile

level

Show facility logging configuration

assoc_mgr

Show Association Manager Logging Configuration

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level backup

[no] logging level { backup | flexlink } <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

backup

Set level for Switchport Backup syslog messages

flexlink

Set level for Switchport Backup syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bfd

[no] logging level bfd <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bfd

Set level for bfd syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bgp

[no] logging level bgp <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bgp

Set syslog filter level for BGP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bloggerd

[no] logging level bloggerd <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bloggerd

Set level for BloggerD syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bootvar

[no] logging level bootvar <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bootvar

Set level for bootvar

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level callhome

logging level callhome <i0> | no logging level callhome [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

callhome

Callhome syslog level

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level capability

[no] logging level capability <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

capability

Set syslog level for mig utils daemon

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cdp

logging level cdp <i0> | no logging level cdp [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

cdp

Set level for CDP syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cfs

[no] logging level cfs <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level clis

[no] logging level clis <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

clis

Set syslog filter level for CLIS

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level clk_mgr

[no] logging level clk_mgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

clk_mgr

Set level for clock manager syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level confcheck

{ logging level confcheck <i0> | no logging level confcheck [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level copp

logging level copp <i0> | no logging level copp [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

copp

Set level for copp syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level core-dmon

{ logging level core-dmon <i0> | no logging level core-dmon [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

core-dmon

core daemon syslog level

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cts

[no] logging level cts <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

cts

Set level for cts syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level device-alias

[no] logging level device-alias <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

device-alias

Set syslog level for Device Alias Distribution Service

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dhclient

[no] logging level dhclient <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dhclient

Set level for dhcp client syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dhcp_snoop

logging level dhcp_snoop <level> | no logging level dhcp_snoop [ <level> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dhcp_snoop

Set level for dhcp snoop syslog messages

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level diagclient

[no] logging level diagclient <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

diagclient

Set level for GOLD DiagClient syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level diagmgr

[no] logging level diagmgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

diagmgr

Set level for GOLD DiagMgr syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dot1x

logging level dot1x <i0> | no logging level dot1x [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dot1x

Set level for dot1x syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dpvm

[no] logging level dpvm <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dpvm

Set syslog level for DPVM

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ecp

[no] logging level ecp <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ecp

Set syslog filter level for ECP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level eigrp

[no] logging level eigrp [ <eigrp-ptag> ] <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

eigrp

Set syslog filter level for EIGRP

eigrp-ptag

(Optional) Process tag

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level eltm

logging level eltm <i0> | no logging level eltm

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

eltm

Set level for eltm syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level epbr

[no] logging level epbr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

epbr

Set level for epbr syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level epp

[no] logging level epp <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

epp

Set level for EPP syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ethpm

[no] logging level ethpm <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ethpm

Set level for ethpm syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ethpm link

[no] logging level ethpm { link-up | link-down } <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ethpm

Set level for ethpm syslog messages

link-up

Configure logging level for link up syslog messages

link-down

Configure logging level for link down syslog messages

level

Logging Level

Command Mode

  • /exec/configure

logging level evb

[no] logging level evb <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

evb

Set syslog filter level for EVB

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level evmc

[no] logging level evmc <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

evmc

Set level for evmc syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level evmed

[no] logging level evmed <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

evmed

Set level for evmed syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level evms

[no] logging level evms <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

evms

Set level for evms syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level fabric forwarding

[no] logging level fabric forwarding <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

fabric

Fabric

forwarding

Fabric Forwarding Protocol: Host Mobility Manager (HMM)

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level fabricpath switch-id

[no] logging level fabricpath switch-id <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

fabricpath

fabricpath configuration

switch-id

switch-id submodule of fabricpath

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level fc2d

[no] logging level fc2d <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

fc2d

Set level for fc2d syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level fcdomain

[no] logging level fcdomain <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

fcdomain

set level for fcdomain syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level fcns

[no] logging level fcns <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults