Most printable and extended ASCII characters are acceptable for use in names and passwords. Certain characters are not allowed in HX Data Platform user names, passwords, virtual machine names, storage controller VM names, and datastore names. Folders and resource pools do not have character exceptions.

However, to simplify names and passwords, consider not using these special characters, as they are frequently assigned special purposes.

ampersand (&), apostrophe ('), asterisk (*), at sign (@), back slash (\), colon (:), comma (,), dollar sign ($), exclamation (!), forward slash (/), less than sign (<), more than sign (>), percent (%), pipe (|), pound (#), question mark (?), semi-colon (;)

When entering special characters, consider the shell being used. Different shells have different sensitive characters. If you have special characters in your names or passwords, place them in a single quote, 'speci@lword!'

HX Storage Cluster Name―HX cluster names cannot exceed 50 characters.

HX Storage Cluster Host Names―HX cluster host names cannot exceed 15 characters.

Virtual Machine and Datastore Names―Most characters used to create a virtual machine name, controller VM name, or datastore name are acceptable. Escaped characters are acceptable for virtual machine, controller VM names, or datastore names.

Maximum characters―Virtual machine names can have up to 15 characters.

Excluded characters―Do not use the following character in any user virtual machine name or datastore name for which you want to enable snapshots:

• accent grave (`)

Special characters―The following special characters are acceptable for user virtual machine or datastore names:

• ampersand (&), apostrophe ('), asterisk (*), at sign (@), back slash (\), circumflex (^), colon (:), comma (,), dollar sign ($), dot (.), double quotation ("), equal sign (=), exclamation (!), forward slash (/), hyphen (-), left curly brace ({), left parentheses ((), left square bracket ([), less than sign (<), more than sign (>), percent (%), pipe (|), plus sign (+), pound (#), question mark (?), right curly brace (}), right parentheses ()), right square bracket (]), semi-colon (;), tilde (~), underscore (_)

Username Requirements

Usernames can be specific to the HX Data Platform component and must meet UCS Manager username requirements.

UCS Manager username requirements.

• Number of characters: between 6 and 32 characters

• Must be unique within Cisco UCS Manager.

• Must start with an alphabetic character.

• Must have: alphabetic characters (upper or lower case).

• Can have: numeric characters. Cannot be all numeric characters.

• Only special character allowed: underscore (_), dash (-), dot (.)

Controller VM Password Requirements

The following rules apply to controller VM root and admin user passwords.

Note	General rule about passwords: Do not include them in a command string. Allow the command to prompt for the password.

• Minimum Length: 10

• Minimum 1 Uppercase

• Minimum 1 Lowercase

• Minimum 1 Digit

• Minimum 1 Special Character

• A maximum of 3 retry to set the new password

To change a controller VM password, always use the hxcli command. Do not use another change password command, such as a Unix password command.

1. Login to the management controller VM.

2. Run the hxcli security password set [-h] [--user USER] command.

   The change is propagated to all the controller VMs in the HX cluster.

UCS Manager Password Format and Character Requirements

The following is a summary of format and character requirements for UCS Manager passwords. See the Cisco UCS Manager documentation for additional information.

• Characters classes: lower case letters, upper case letters, numbers, special characters.

  Passwords are case sensitive.

• Character length: Minimum 6, maximum 80

  Minimum 6 characters required, if characters from all four character classes.

  Minimum 7 characters required, if characters from at least three character classes.

  Minimum 8 characters required, if characters from only one or two character classes.

• Start and end characters: An upper case letter at the beginning or a number at the end of the password do not count toward the total number of characters.

  If password starts with uppercase letter, then 2 uppercase letters are required. If password ends with a digit, then 2 digits are required.

  Examples that meet the requirements:

  • h#56Nu - 6 characters. 4 classes. No starting upper case letter. No ending number.

  • h5xj7Nu - 7 characters. 3 classes. No starting upper case letter. No ending number.

  • XhUwPcNu - 8 characters. 2 classes. No starting upper case letter. No ending number.

  • Xh#5*Nu - 6 characters counted. 4 characters classes. Starting upper case letter. No ending number.

  • h#5*Nu9 - 6 characters counted. 4 characters classes. No starting upper case letter. Ending number.

• Consecutive characters: Maximum 2. For example, hhh###555 is not acceptable.

• Excluded characters:

  UCS Manager passwords cannot contain the escape (\) character.