Cisco Elastic Services Controller 5.2 Install and Upgrade Guide

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book

Results

Updated:
May 31, 2020

Chapter: Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine

This chapter describes how to install Cisco Elastic Services Controller on a Kernel-based Virtual Machine and includes the following sections:

Installing Cisco Elastic Services Controller in a Kernel-based Virtual Machine

Cisco Elastic Services Controller can be installed in a Kernel-based Virtual Machine. You can install Cisco Elastic services controller in a Kernel-based Virtual Machine using libvirt.

Preparing to Install Cisco Elastic Services Controller on a Kernel-based Virtual Machine

If you plan to run Cisco Elastic Services Controller on a kernel-based virtual machine, make sure the following are setup:

Notes

Python 2.7 or 3.x

Installed by default on Linux

python-setuptools

Installed by default on Linux

pip

On RHEL: 
# easy_install pip
Since the installation using pip compiles source files, the gcc and python development packages are also required on RHEL. To install these packages on RHEL: 
# yum install gcc python-devel
On Ubuntu: Installed by default. Since the installation using pip compiles source files, the gcc and python development packages are also required on Ubuntu. To install these packages on Ubuntu: 
# apt-get install python-dev

OpenStack clients 

# pip install python-keystoneclient
# pip install python-cinderclient
# pip install python-novaclient
# pip install python-neutronclient

genisoimage

On RHEL: 
# yum install  genisoimage
On Ubuntu: 
# apt-get install genisoimage

libvirt and virtinst

On RHEL 6.x: 
# yum install libvirt-python python-virtinst
On RHEL 7.x: 
# yum install libvirt-python virt-install
On Ubuntu: 
# apt-get install libvirt-dev 
# pip install libvirt-python

Note

libvirt will create the default network automatically.

Installing Elastic Services Controller on a Kernel-Based Virtual Machine

To install standalone Elastic Services Controller (ESC) on a kernel-based virtual machine, do the following:

Procedure

Step 1

Load the variables from the openerc file that contains OpenStack credentials: 

cat ./openrc.sh
export OS_TENANT_NAME='<OS tenant username>'
export OS_USERNAME='<OS username>'
export OS_PASSWORD='<OS password>'
export OS_AUTH_URL='http://<Openstack Host>:5000/v2.0/'

source ./openrc.sh
Step 2

Copy the ESC qcow2 image and the bootvm.py into the kernel-based VM.

Step 3

Boot ESC on a kernel-based VM on the default network that was created when libvirt was installed, use one of the following command: 

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password> --libvirt --image <image_name> esc-vm --net <default network>
Step 4

Boot ESC on a kernel-based VM on the default network with static IP, using the following command: 

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password> --libvirt --image <image_name> esc-vm --net <network> --ipaddr <ip_address>
Step 5

Get a list of used IP addresses in your network. Use IP addresses that are not in the list for both HA Active/Standby bootvm.py command and for kad_vip. Determine the first 3 octets of your network (i.e. 192.168.122) and pass it in the below command : 

arp -an | grep 192.168.122
Step 6

To install ESC on a kernel-based VM in high availability, use the following command twice for both the HA nodes:

Note 

For the second bootvm.py command, use the other HA instance name. 

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password> --libvirt --image <image_name> --ha_mode drbd --gateway_ip <default_gateway_ip_address> --ipaddr <ip_address>
 --ha_node_list <ha peer ip addresses separated by comma> --kad_vip <vip address> esc-ha-1 --net <network>

Next Steps: Cisco Elastic Services Controller Kernel-based Virtual Machine

Verifying ESC installation for a Kernel-based Virtual Machine (KVM)

After deploying ESC on a Kernel-based virtual machine, use the following procedure to verify the deployment.

Procedure

Step 1

Check that the ESC VMs have booted using the following command: 

$ virsh list
Step 2

Get the IP address of the ESC VM, using the following command: 

$ arp -an | grep <ip_address>
Step 3

Connect to ESC using SSH and verify the processes are running: 

$ ssh USERNAME@ESC_IP

Troubleshooting Tips

When SSH access is not available, due to network conditions or ESC startup failures, you can connect to ESC through console(if enabled in ESC VM image) or VNC access. To access ESC VM through VNC, do the following:
  1. Identify the vnc port. 
    virsh dumpxml 10 | fgrep vnc

  2. Create a ssh tunnel to the local vnc port to allow connection from your remote VNC client.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco