Cisco Fourth-Generation LTE Network Interface Module Installation Guide
Recommended Practices for the 4G-LTE-NIM
Preventing Electrostatic Discharge Damage
General Maintenance Guidelines
Installing the SIM card on the Cisco 4G-LTE-NIM
Installing the Cisco 4G-LTE-NIM into a Cisco 4000 Series ISR
Removing the Cisco 4G-LTE-NIM from a Cisco 4000 Series ISR
This document provides an overview of the hardware and installation information for Cisco Fourth-Generation Long-Term Evolution (4G-LTE) Network Interface Module (NIM) on Cisco 4000 Series Integrated Services Router (ISR).
This document contains the following sections:
– Preventing Electrostatic Discharge Damage
Cisco 4G-LTE NIM addresses the modular 4G-LTE cellular connectivity on the Cisco 4000 Series ISRs. Cisco 4G-LTE-NIM is feature-compatible with Cisco EHWIC-4G-LTE.
Table 1 describes the Cisco 4G LTE NIM SKUs.
Figure 1 shows the 4G-LTE-NIM front panel. Table 2 lists the 4G-LTE-NIM ports and LED indicators and describes their behavior. The LEDs provide a visual indication of the NIM status and the currently-selected services.
Note You should remove the caps before attaching the antennas.
Figure 1 Front Panel of the Cisco 4G-LTE-NIM
LED—GPS1 |
|||
LED—RSSI2 |
M1 DIV—Diversity Antenna Connector (TNC3), with dust cap removed. |
||
GPS—GPS Antenna Connector (SMA4), with knurled metal cap removed. |
M0 MAIN—Main Antenna Connector (TNC), with dust cap removed. |
The reserved (RSVD) diagnostic port is not required for normal activation or operation. This port supports modem debug or provisioning. |
|
The Enable (EN) LED is standard on NIMs and indicates the module state, as shown in Figure 1. Solid green —Indicates powered on and functioning normally. Solid amber —Indicates Module has some type of failure. Off —Indicates Module does not have power. It may also remain off the first time when the NIM is powered on, until it is configured by the host software. |
|
Solid green —Indicates the modem is powered, associated and authenticated but not receiving or transmitting data. Slow blinking green —Indicates the modem is powered, but not associated or authenticated; still searching for service. Check the antenna, cable, SIM card, or the user account with your service provider. Fast blinking green —Indicates the modem is powered and is transmitting or receiving. The blink rate is proportional to the transmitted and received data rate. Solid Amber —Indicates the modem is reserved for future use. |
|
Indicates the level of signal strength received by the NIM. Solid green —Indicates a high RSSI (greater than –69 dBm). Solid blue —Indicates medium RSSI (-89 to -69dBm). Solid amber —Indicates low RSSI (-99 to -89dBm). |
|
Indicates which cellular service is available. Solid green —Indicates 4G service is enabled (LTE). Solid blue —Indicates 3G service is enabled, e.g. EDVO, HSPA+. Solid amber —Indicates 2G service is enabled, e.g. 1xRTT, EDGE. |
|
Indicates whether GPS service is enabled. |
|
Table 3 lists the Cisco antennas that are supported for use on the Cisco 4G-LTE NIM.
Multiband dipole antenna. For more information, see Cisco 4G/3G Omnidirectional Dipole Antenna (4G-LTE-ANTM-D). |
|||
Multiband omnidirectional ceiling-mount antenna. For more information, see Cisco 4G Indoor Ceiling-Mount Omnidirectional Antenna (4G-ANTM-OM-CM). |
|||
Multiband outdoor omnidirectional stick antenna. For more information, see Cisco Outdoor Omnidirectional Antenna for 2G/3G/4G Cellular (ANT-4G-OMNI-OUT-N). |
|||
1.5 dBi (peak gain with 10-foot cable) or 0.8 dBi (peak gain with 15-foot cable) 3.7 dBi (peak gain with 10-foot cable) or 0.2 dBi (peak gain with 15-foot cable) |
Low-profile outdoor saucer antenna. For more information, see Cisco Integrated 4G Low-Profile Outdoor Saucer Antenna (ANT-4G-SR-OUT-TNC). |
||
This is the default antenna extension base. For more information, see Cisco Single-Port Antenna Stand for Multiband TNC Male-Terminated Portable Antenna (Cisco 4G-AE015-R, Cisco 4G-AE010-R). |
|||
Single-port antenna extension base with 15-foot cable. For more information, see Cisco Single-Port Antenna Stand for Multiband TNC Male-Terminated Portable Antenna (Cisco 4G-AE015-R, Cisco 4G-AE010-R). |
|||
4G lightning arrestor kit for use on Cisco 4G wireless devices. For more information, see Cisco 4G Lightning Arrestor (4G-ACC-OUT-LA). |
|||
4G lightning arrestor kit for use on Cisco 4G wireless devices. For more information, see Lightning Arrestor for the Cisco 1240 Connected Grid Router. |
Table 4 lists loss information and operating frequency levels for the ultra-low-loss (ULL) LMR 200 cables and LMR 400 cables available from Cisco for use with Cisco 4G-LTE-NIM.
Plenum Rated?
5
|
|||||
---|---|---|---|---|---|
1.4 dB @ 700 MHz |
|||||
2.3 dB @ 700 MHz |
This section describes recommended practices for safe and effective installation of the hardware described in this document.
Safety warnings included in this section apply to the 4G-LTE-NIMs that are used on the Cisco 4000 series ISRs.
To prevent hazardous conditions, follow these safety recommendations while working with this equipment:
– Installing or removing a router chassis
– Use caution; do not become a victim yourself.
– Turn off power to the room using the emergency power-off switch.
– Determine the condition of the victim and send another person to get medical aid or call for help.
– Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.
Electrostatic discharge can damage equipment and electrical circuitry. Electrostatic discharge occurs when electronic printed circuit cards, such as those used in Cisco network modules, are improperly handled and can result in complete or intermittent equipment failure. Always observe the following electrostatic discharge damage (ESD) prevention procedures when installing, removing, or replacing any electronic printed circuit cards:
The following maintenance guidelines apply to the Cisco Network Interface Module for 4G-LTE-NIM:
The following safety warning statements apply to all hardware procedures involving the 4G-LTE-NIM for Cisco 4000 series ISRs. Translations of these warnings are available in the Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information document, which ships with all individual NIM orders, and is also available on http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/rcsi/IOHrcsi.html.
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038
Warning To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039
Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040
Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046
The following warnings apply in Australia:
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43
Warning Because invisible laser radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 125
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001
Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Both LAN and WAN ports may use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning Hazardous network voltages are present in WAN ports regardless of whether power to the router is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the router first. Statement 1026
Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041
Warning The telecommunications lines must be disconnected 1) before unplugging the main power connector and/or 2) while the housing is open. Statement 1043
The SIM card socket is located on the bottom side of the NIM. Figure 2 shows the silk-screen of the NIM.
Figure 2 Silkscreen of the NIM
Follow these steps to install the SIM card:
Step 1 To unlock the SIM socket cover, slide the cover toward the faceplate in the direction of the unlock arrow, as shown in Figure 3.
Note The SIM cover unlocks and locks with a tactile 'click'.
Figure 3 Unlock the SIM Socket Cover
Step 2 Gently lift the cover on its hinges, and place the SIM card down on the metallic contacts, as shown in Figure 4.
Figure 4 Open the SIM cover, and Place the SIM Card on the Contacts
Step 3 Gently push down the cover to close.
Step 4 To lock the cover, slide it away from the faceplate in the direction of the lock arrow, as shown in Figure 5.
Figure 5 Lock the SIM Socket Cover
To install the 4G-LTE-NIM into a Cisco 4000 series ISR, see the following Figure 6 and the procedure that follows:
Figure 6 Installing the Cisco 4G-LTE-NIM into a Cisco 4000 Series ISR
Make sure that you connect the wrist-strap clip to an unpainted portion of the chassis frame to channel
Use the following procedure to install the Cisco 4G-LTE-NIM on your router:
Step 1 Read the “Safety Warnings” section before you perform any module replacement.
Step 2 Remove the blank faceplate installed over the NIM slot of the ISR.
Step 3 Insert the NIM into the router. (See Figure 6).
Step 4 Tighten the captive mounting screws on the module faceplate with the help of a number 1 Phillips or flat-blade screwdriver.
Use the following procedure to remove the Cisco 4G-LTE-NIM from your router:
Step 1 Read the “Safety Warnings” section before you perform any module replacement.
Step 2 Locate the 4G-LTE-NIM card to be removed.
Step 3 Unscrew the captive mounting screws on the module faceplate with the help of a number 1 Phillips or flat-blade screwdriver.
Step 4 Pull the 4G-LTE-NIM out of the chassis.
Step 5 Place the 4G-LTE-NIM card in an antistatic bag to protect it from electrostatic discharge (ESD) damage.
Cisco Fourth-Generation LTE Network Interface Module Configuration Guide for Cisco 4000 Series ISR |
Cisco Fourth-Generation LTE Network Interface Module Software Configuration Guide |
Hardware Installation Guide for the Cisco 4000 Series Integrated Services Router |
|
General information about configuration and the command reference. |
Software Configuration Guide for the Cisco 4000 Seris Integrated Services Router |
Regulatory compliance information for the Cisco 4000 Series ISR. |
Regulatory Compliance and Safety Information for the Cisco 4000 Series Integrated Services Router |