NX-API Developer Sandbox

NX-API Developer Sandbox: NX-OS Releases Prior to 9.2(2)

About the NX-API Developer Sandbox

The NX-API Developer Sandbox is a web form hosted on the switch. It translates NX-OS CLI commands into equivalent XML or JSON payloads, and converts NX-API REST payloads into their CLI equivalents.

The web form is a single screen with three panes — Command (top pane), Request, and Response — as shown in the figure.

Figure 1. NX-API Developer Sandbox with Example Request and Output Response

Controls in the Command pane allow you to choose a message format for a supported API, such as NX-API REST, and a command type, such as XML or JSON. The available command type options vary depending on the selected message format.

When you type or paste one or more CLI commands into the Command pane, the web form converts the commands into an API payload, checking for configuration errors, and displays the resulting payload in the Request pane. If you then choose to post the payload directly from the Sandbox to the switch, using the POST button in the Command pane, the Response pane displays the API response.

Conversely, when you type an NX-API REST designated name (DN) and payload into the Command pane and select the nx-api rest Message format and the model Command type, Developer Sandbox checks the payload for configuration errors, then the Response pane displays the equivalent CLIs.

Guidelines and Limitations

Following are the guidelines and limitations for the Developer Sandbox:

  • Clicking POST in the Sandbox commits the command to the switch, which can result in a configuration or state change.

  • Some feature configuration commands are not available until their associated feature has been enabled.

Configuring the Message Format and Command Type

The Message Format and Command Type are configured in the upper right corner of the Command pane (the top pane). For Message Format, choose the format of the API protocol that you want to use. The Developer Sandbox supports the following API protocols:

Table 1. NX-OS API Protocols

Protocol

Description

json-rpc

A standard lightweight remote procedure call (RPC) protocol that can be used to deliver NX-OS CLI commands in a JSON payload. The JSON-RPC 2.0 specification is outlined by jsonrpc.org.

xml

Cisco NX-API proprietary protocol for delivering NX-OS CLI or bash commands in an XML payload.

json

Cisco NX-API proprietary protocol for delivering NX-OS CLI or bash commands in a JSON payload.

nx-api rest

Cisco NX-API proprietary protocol for manipulating and reading managed objects (MOs) and their properties in the internal NX-OS data management engine (DME) model. For more information, see the Cisco Nexus NX-API References.

nx yang

The YANG ("Yet Another Next Generation") data modeling language for configuration and state data.

When the Message Format has been chosen, a set of Command Type options are presented just below the Message Format control. The Command Type setting can constrain the input CLI and can determine the Request and Response format. The options vary depending on the Message Format selection. For each Message Format, the following table describes the Command Type options:

Table 2. Command Types

Message format

Command type

json-rpc

  • cli — show or configuration commands

  • cli-ascii — show or configuration commands, output without formatting

xml

  • cli_show — show commands. If the command does not support XML output, an error message will be returned.

  • cli_show_ascii — show commands, output without formatting

  • cli_conf — configuration commands. Interactive configuration commands are not supported.

  • bash — bash commands. Most non-interactive bash commands are supported.

    Note 
    The bash shell must be enabled in the switch.

json

  • cli_show — show commands. If the command does not support XML output, an error message will be returned.

  • cli_show_ascii — show commands, output without formatting

  • cli_conf — configuration commands. Interactive configuration commands are not supported.

  • bash — bash commands. Most non-interactive bash commands are supported.

    Note 
    The bash shell must be enabled in the switch.

nx-api rest

  • cli — configuration commands

  • model — DN and corresponding payload.

nx yang

  • json — JSON structure is used for payload

  • xml — XML structure is used for payload

Output Chunking

In order to handle large show command output, some NX-API message formats support output chunking for show commands. In this case, an Enable chunk mode checkbox appears below the Command Type control along with a session ID (SID) type-in box.

When chunking is enabled, the response is sent in multiple "chunks," with the first chunk sent in the immediate command response. In order to retrieve the next chunk of the response message, you must send an NX-API request with SID set to the session ID of the previous response message.

Using the Developer Sandbox

Using the Developer Sandbox to Convert CLI Commands to Payloads


Tip

Online help is available by clicking Quick Start in the upper right corner of the Sandbox window.

Additional details, such as response codes and security methods, can be found in the NX-API CLI chapter.

Only configuration commands are supported.


Procedure


Step 1

Configure the Message Format and Command Type for the API protocol you want to use.

For detailed instructions, see Configuring the Message Format and Command Type.

Step 2

Type or paste NX-OS CLI configuration commands, one command per line, into the text entry box in the top pane.

You can erase the contents of the text entry box (and the Request and Response panes) by clicking Reset at the bottom of the top pane.

Step 3

Click the Convert at the bottom of the top pane.

If the CLI commands contain no configuration errors, the payload appears in the Request pane. If errors are present, a descriptive error message appears in the Response pane.

Step 4

When a valid payload is present in the Request pane, you can click POST to send the payload as an API call to the switch.

The response from the switch appears in the Response pane.

Warning 
Clicking POST commits the command to the switch, which can result in a configuration or state change.
Step 5

You can copy the contents of the Request or Response pane to the clipboard by clicking Copy in the pane.

Step 6

You can obtain a Python implementation of the request on the clipboard by clicking Python in the Request pane.


NX-API Developer Sandbox: NX-OS Release 9.2(2) and Later

About the NX-API Developer Sandbox

The Cisco NX-API Developer Sandbox is a web form hosted on the switch. It translates NX-OS CLI commands into equivalent XML or JSON payloads and converts NX-API REST payloads into their CLI equivalents.

The web form is a single screen with three panes — Command (top pane), Request (middle pane), and Response (bottom pane) — as shown in the figure below. The designated name (DN) field is located between the Command and Request panes (seen in the figure below located between the POST and Send options).

The Request pane also has a series of tabs. Each tab represents a different language: Python, Python3, Java, JavaScript, and Go-Lang. Each tab enables you to view the request in the respective language. For example, after converting CLI commands into an XML or JSON payload, click the Python tab to view the request in Python, which you can use to create scripts.

Figure 2. NX-API Developer Sandbox with Example Request and Output Response

Controls in the Command pane enable you to choose a supported API, such as NX-API REST, an input type, such as model (payload) or CLI, and a message format, such as XML or JSON. The available options vary depending on the chosen method.

When you choose the NXAPI-REST (DME) method, type or paste one or more CLI commands into the Command pane,and click Convert, the web form converts the commands into a REST API payload, checking for configuration errors, and displays the resulting payload in the Request pane. If you then choose to post the payload directly from the sandbox to the switch (by choosing the POST option and clicking SEND), the Response pane displays the API response. For more information, see Using the Developer Sandbox to Convert CLI Commands to REST Payloads

Conversely, the Cisco NX-API Developer Sandbox checks the payload for configuration errors then displays the equivalent CLis in the Response pane. For more information, see Using the Developer Sandbox to Convert from REST Payloads to CLI Commands

Guidelines and Limitations

Following are the guidelines and limitations for the Developer Sandbox:

  • Clicking Send in the Sandbox commits the command to the switch, which can result in a configuration or state change.

  • Some feature configuration commands are not available until their associated feature has been enabled.

  • Using Sandbox to convert with DN is supported only for finding the DN of a CLI config. Any other workflow, for example, using DME to convert DN for CLI configuration commands is not supported.

  • The Command pane (the top pane) supports a maximum of 10,000 individual lines of input.

Configuring the Message Format and Input Type

The Method, Message format, and Input type are configured in the upper right corner of the Command pane (the top pane). For Method, choose the format of the API protocol that you want to use. The Cisco NX-API Developer Sandbox supports the following API protocols:

Table 3. NX-OS API Protocols

Protocol

Description

NXAPI-CLI

Cisco NX-API proprietary protocol for delivering NX-OS CLI or bash commands in an XML or a JSON payload.

NXAPI-REST (DME)

Cisco NX-API proprietary protocol for manipulating and reading managed objects (MOs) and their properties in the internal NX-OS data management engine (DME) model. The NXAPI-REST (DME) protocol displays a drop-down list that enables you to choose from the following methods:

  • POST

  • GET

  • PUT

  • DELETE

For more information about the Cisco Nexus 3000 and 9000 Series NX-API REST SDK, see https://developer.cisco.com/site/cisco-nexus-nx-api-references/.

RESTCONF (Yang)

The YANG ("Yet Another Next Generation") data modeling language for configuration and state data.

The RESTCONF (Yang) protocol displays a drop-down list that enables you to choose from the following methods:

  • POST

  • GET

  • PUT

  • PATCH

  • DELETE

When you choose the Method, a set of Message format or Input type options are displayed in a drop-down list. The Message format can constrain the input CLI and determine the Request and Response format. The options vary depending on the Method you choose.

The following table describes the Input/Command type options for each Message format:

Table 4. Command Types

Method

Message format

Input/Command type

NXAPI-CLI

json-rpc

  • cli — show or configuration commands

  • cli-ascii — show or configuration commands, output without formatting

  • cli-array — show commands. Similar to cli, but with cli_array, data is returned as a list of one element, or an array, within square brackets, [ ].

NXAPI-CLI

xml

  • cli_show — show commands. If the command does not support XML output, an error message will be returned.

  • cli_show_ascii — show commands, output without formatting

  • cli_conf — configuration commands. Interactive configuration commands are not supported.

  • bash — bash commands. Most non-interactive bash commands are supported.

    Note 
    The bash shell must be enabled in the switch.

NXAPI-CLI

json

  • cli_show — show commands. If the command does not support XML output, an error message will be returned.

  • cli_show_array — show commands. Similar to cli_show, but with cli_show_array, data is returned as a list of one element, or an array, within square brackets [ ].

  • cli_show_ascii — show commands, output without formatting

  • cli_conf — configuration commands. Interactive configuration commands are not supported.

  • bash — bash commands. Most non-interactive bash commands are supported.

    Note 
    The bash shell must be enabled in the switch.

NXAPI-REST (DME)

  • cli — CLI to model conversion

  • model — Model to CLI conversion.

RESTCONF (Yang)

  • json — JSON structure is used for payload

  • xml — XML structure is used for payload

Output Chunking

In order to handle large show command output, some NX-API message formats support output chunking for show commands. In this case, an Enable chunk mode check box appears below the Command Type control along with a session ID (SID) type-in box.

When chunking is enabled, the response is sent in multiple "chunks," with the first chunk sent in the immediate command response. In order to retrieve the next chunk of the response message, you must send an NX-API request with SID set to the session ID of the previous response message.

Using the Developer Sandbox

You can use the Cisco NX-API Developer Sandbox to make multiple conversions, including the following:

Using the Developer Sandbox to Convert CLI Commands to REST Payloads


Tip

  • Online help is available by clicking the help icons (?) next to the field names located in the upper-right corner of the Cisco NX-API Developer Sandbox window.

  • For additional details, such as response codes and security methods, see the NX-API CLI chapter.

  • Only configuration commands are supported.


The Cisco NX-API Developer Sandbox enables you to convert CLI commands to REST payloads.

Procedure


Step 1

Click the Method drop-down list and choose NXAPI-REST (DME).

The Input type drop-down list appears.

Step 2

Click the Input type drop-down list and choose cli.

Step 3

Type or paste NX-OS CLI configuration commands, one command per line, into the text entry box in the top pane.

You can erase the contents of the text entry box (and the Request and Response panes) by clicking Reset at the bottom of the top pane.

Step 4

Click Convert.

If the CLI commands contain no configuration errors, the payload appears in the Request pane. If errors are present, a descriptive error message appears in the Response pane.

Step 5

(Optional) To send a valid payload as an API call to the switch, click Send.

The response from the switch appears in the Response pane.

Warning 
Clicking Send commits the command to the switch, which can result in a configuration or state change.
Step 6

(Optional) To obtain the DN for an MO in the payload:

  1. From the Request pane, choose POST.

  2. Click the Convert drop-down list and choose Convert (with DN).

The payload appears with with a dn field that contains the DN that corresponds to each MO in the payload.

Step 7

(Optional) To overwrite the current configuration with a new configuration:

  1. Click the Convert drop-down list and choose Convert (for Replace). The Request pane displays a payload with a status field set to replace.

  2. From the Request pane, choose POST.

  3. Click Send.

The current configuration is replaced with the posted configuration. For example, if you start with the following configuration:


interface eth1/2
  description test
  mtu 1501

Then use Convert (for Replace) to POST the following configuration:


interface eth1/2
  description testForcr

The mtu configuration is removed and only the new description (testForcr) is present under the interface. This change is confirmed when entering show running-config .

Step 8

(Optional) To copy the contents of a pane, such as the Request or Response pane, click Copy. The contents o the respective pane is copied to the clipboard.

Step 9

(Optional) To convert the request into an of the formats listed below, click on the appropriate tab in the Request pane:

  • Python

  • Python3

  • Java

  • JavaScript

  • Go-Lang


Using the Developer Sandbox to Convert from REST Payloads to CLI Commands

The Cisco NX-API Developer Sandbox enables you to convert REST payloads to corresponding CLI commands. This option is only available for the NXAPI-REST (DME) method.


Tip

  • Online help is available by clicking help icons (?) next to the Cisco NX-API Developer Sandbox field names. Click a help icon get information about the respective field.

    For additional details, such as response codes and security methods, see the chapter NX-API CLI.

  • The top-right corner of the Cisco NX-API Developer Sandbox contains links for additional information. The links that appear depend on the Method you choose. The links that appear for the NXAPI-REST (DME) method:

    • NX-API References—Enables you to access additional NX-API documentation.

    • DME Documentation—Enables you to access the NX-API DME Model Reference page.

    • Model Browser—Enables you to access Visore, the Model Browser. Note that you might have to manually enter the IP address for your switch to access the Visore page:

      https://management-ip-address/visore.html.


Procedure


Step 1

Click the Method drop-down list and choose NXAPI-REST (DME).

Example:

Step 2

Click the Input Type drop-down list and choose model.

Step 3

Enter the designated name (DN) that corresponds to the payload in the field above the Request pane.

Step 4

Enter the payload in the Command pane.

Step 5

Click Convert.

Example:

For this example, the DN is /api/mo/sys.json and the NX-API REST payload is:
{
  "topSystem": {
    "attributes": {
      "name": "REST2CLI"
    }
  }
}
When you click on the Convert button, the CLI equivalent appears in the CLI pane as shown in the following image.
Note 

The Cisco NX-API Developer Sandbox cannot convert all payloads into equivalent CLIs, even if the sandbox converted the CLIs to NX-API REST payloads. The following is a list of possible sources of error that can prevent a payload from completely converting to CLI commands:

Table 5. Sources of REST2CLI Errors

Payload Issue

Result

The payload contains an attribute that does not exist in the MO.

Example:
api/mo/sys.json
{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/1",
                  "fakeattribute": "totallyFake"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

The Error pane will return an error related to the attribute.

Example:

CLI

Error unknown attribute 'fakeattribute' in element 'l1PhysIf'

The payload includes MOs that aren't yet supported for conversion:

Example:
api/mo/sys.json
{
  "topSystem": {
    "children": [
      {
        "dhcpEntity": {
          "children": [
            {
              "dhcpInst": {
                "attributes": {
                  "SnoopingEnabled": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

The Error Pane will return an error related to the unsupported MO.

Example:

CLI

Error The entire subtree of "sys/dhcp" is not converted.


Using the Developer Sandbox to Convert from RESTCONF to json or XML


Tip

  • Online help is available by clicking the help icon (?) in the upper-right corner of the Cisco NX-API Developer Sandbox window.

  • Click on the Yang Documentation link in the upper right corner of the Sandbox window to go to the Model Driven Programmability with Yang page.

  • Click on the Yang Models link in the upper right corner of the Sandbox window to access the YangModels GitHub site.


Procedure


Step 1

Click the Method drop-down list and choose RESTCONF (Yang).

Example:

Step 2

Click Message format and choose either json or xml.

Step 3

Enter a command in the text entry box in the top pane.

Step 4

Choose a message format.

Step 5

Click Convert.

Example:

For this example, the command is logging level netstack 6 and the message format is json:

Example:

For this example, the command is logging level netstack 6 and the message format is xml:
Step 6

You can also convert the request into the following formats by clicking on the appropriate tab in the Request pane:

  • Python

  • Python3

  • Java

  • JavaScript

  • Go-Lang

Note 

The Java-generated script does not work if you choose the PATCH option from the drop-down menu in the area above the Request tab. This is a known limitation with Java and is expected behavior.