P Commands

packet-size

{ packet-size <packetsize> }

Syntax Description

packet-size

Packet

packetsize

Size

Command Mode

  • /exec/configure/configngoamconnectcheck

param-list param-list

[no] param-list <plistname> [ cross-check ] | param-list <plistname>

Syntax Description

no

(Optional) Negate a command or set its defaults

param-list

Configure a parameter list

plistname

Enter the name of the parameter list

cross-check

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure

parity

[no] parity { even | none | odd }

Syntax Description

no

(Optional) Negate a command or set its defaults

parity

Set terminal parity

even

Even parity

none

No parity

odd

Odd parity

Command Mode

  • /exec/configure/com1

parity

[no] parity <parity-value>

Syntax Description

no

(Optional) Negate a command or set its defaults

parity

Set terminal parity

parity-value

terminal parity value

Command Mode

  • /exec/configure/console

passive-interface default

[no] passive-interface default

Syntax Description

no

(Optional) Negate a command or set its defaults

passive-interface

Suppress routing updates on the interface

default

interfaces passive by default

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

passive-interface default

[no] passive-interface default <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

passive-interface

Suppress IS-IS PDU

default

Undo a command

level

IS-IS level

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

passive-interface default

[no] passive-interface default

Syntax Description

no

(Optional) Negate a command or set its defaults

passive-interface

Suppress routing updates on the interface

default

interfaces passive by default

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

passive-interface default

[no] passive-interface default

Syntax Description

no

(Optional) Negate a command or set its defaults

passive-interface

Suppress routing updates on the interface

default

interfaces passive by default

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

password

password [ vrf { <vrf-name> | <vrf-known-name> } ] { required [ req-for <req-pfx-list> ] | { fallback | option <seq-num> opt-for <opt-pfx-list> } { key-chain <name> } } | no password [ vrf { <vrf-name> | <vrf-known-name> } ] { required | fallback | option <seq-num> }

Syntax Description

no

Negate a command or set its defaults

password

Configure LDP password

vrf

(Optional) VRF Routing/Forwarding instance information

vrf-name

(Optional) VPN Routing/Forwarding instance name

vrf-known-name

(Optional) Known VRF name

required

Password is required for the peer

req-for

(Optional) Prefix list specifying control on LDP peers

req-pfx-list

(Optional) Prefix list for LDP peers

fallback

Specifies a fallback password will follow

option

LDP password option

seq-num

Sequence number of the LDP password option

opt-for

Prefix list specifying control on LDP peers

opt-pfx-list

Prefix list for LDP peers

key-chain

Specifies a key-chain name will follow

name

Key-chain name

Command Mode

  • /exec/configure/ldp

password

password <password-string> | { no | default } password [ <password-string> ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

password

Configure a password for neighbor

password-string

Neighbor password

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-neighbor-stmp /exec/configure/router-bgp/router-bgp-vrf-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor /exec/configure/router-bgp/router-bgp-vrf-prefixneighbor

password

{ [ no ] password <passwd> }

Syntax Description

password

password

passwd

password

Command Mode

  • /exec/configure/dot1x-cred

password prompt username

[no] password prompt username

Syntax Description

no

(Optional) Negate a command or set its defaults

password

Password for the user

prompt

Enable prompt for password

username

Enable prompt for password on username command

Command Mode

  • /exec/configure

password secure-mode

[no] password secure-mode

Syntax Description

no

(Optional) Negate a command or set its defaults

password

Password for the user

secure-mode

Enable secure mode for changing password

Command Mode

  • /exec/configure

password strength-check

[no] password strength-check

Syntax Description

no

(Optional) Negate a command or set its defaults

password

Password for the user

strength-check

Strength check of password

Command Mode

  • /exec/configure

path-option dynamic explicit identifier

[no] path-option [ protect ] <pref> | path-option <pref> dynamic [ attributes <attr-name> | { bandwidth <kbps> | lockdown } + ] | path-option [ protect ] <pref> explicit { identifier <id-num> | name <name> } [ { attributes <attr-name> [ verbatim ] | { bandwidth <kbps> | lockdown | verbatim } + } ]

Syntax Description

no

Negate a command or set its defaults

path-option

a primary or fallback path setup option

protect

(Optional) a path protection setup option

pref

preference for this path option

dynamic

setup based on dynamically calculated path

explicit

setup based on preconfigured path

identifier

Specify an IP explicit path by number

id-num

Number of ip explicit path

name

Specify an IP explicit path by name

name

Name of ip explicit path

attributes

(Optional) Specify an LSP attribute list

attr-name

(Optional) Name of LSP attribute list

verbatim

(Optional) send out path as is, with no checking

bandwidth

(Optional) override the bandwidth configured on the tunnel

kbps

(Optional) bandwidth requirement in kbps

lockdown

(Optional) not a candidate for reoptimization

kbps

(Optional) bandwidth requirement in kbps

lockdown

(Optional) not a candidate for reoptimization

Command Mode

  • /exec/configure/if-te /exec/configure/tunnel-te/cbts-member

path-selection metric igp

[no] path-selection metric | path-selection metric { igp | te }

Syntax Description

no

Negate a command or set its defaults

path-selection

Path Selection Configuration

metric

Metric type for path calculation

igp

Use IGP Metric

te

Use TE Metric

Command Mode

  • /exec/configure/if-te /exec/configure/tunnel-te/cbts-member

path-selection metric igp

path-selection metric { igp | te } | no path-selection metric

Syntax Description

no

Negate a command or set its defaults

path-selection

Path Selection Configuration

metric

Metric Type Configuration

igp

Use IGP metric

te

Use TE metric (*Default)

Command Mode

  • /exec/configure/te

path-selection overload allow

[no] path-selection overload allow | path-selection overload allow { head [ middle ] [ tail ] | middle [ tail ] | tail }

Syntax Description

no

Negate a command or set its defaults

path-selection

Path Selection Configuration

overload

Overload Node Configuration

allow

Allow overloaded nodes in CSPFs

head

Allow overloaded head node in TE CSPF

middle

(Optional) Allow overloaded middle node in TE CSPF

tail

(Optional) Allow overloaded tail node in TE CSPF

Command Mode

  • /exec/configure/te

path next-hop out-label-stack

{ no path <path-num> | path <path-num> next-hop <next-hop> out-label-stack { <static-outlabel> + | implicit-null } }

Syntax Description

no

Negate a command or set its defaults

path

Configure an outgoing path for the LSP

path-num

Path identifier

next-hop

Nexthop

next-hop

Destination IPv4 next hop

out-label-stack

Series of output labels

static-outlabel

Label Value

implicit-null

IETF MPLS implicit null label (3)

Command Mode

  • /exec/configure/mpls_static/ipv4/lsp/inlabel/forw

pathtrace nve

pathtrace nve { { { { ip { <numeric10> | <numeric11> | unknown } } [ vrf { <vrf-name> | <vrf-known-name> } | { <dot1qid1> } ] } | mac <dmac> <dot1qid> [ <intfid> ] } [ profile <pid> ] [ payload { [ mac-addr <dstmac> <smac> ] [ dot1q <dot1q-id> ] [ ip <dstip> <srcip> | ipv6 <dstipv6> <srcipv6> ] [ port <sport> <dport> ] [ proto <proto-id> ] [ src-intf <src_if> ] } payload-end ] [ copy-to <copy-to-ip> [ ext-id <ext_id> ] ] [

Syntax Description

pathtrace

Test

nve

network virtualization edge

numeric10

Peer vtep ip address

unknown

Peer vtep ip is unknown, will be derived from payload

intfid

(Optional) Name of the interface for ngoam pathtrace on which dot1q is configured

payload

(Optional) Enter customer payload

mac-addr

(Optional) Mac

dstmac

(Optional) Destination mac address

smac

(Optional) Source mac address

dot1q

(Optional) Encapsulation dot1q/bd

dot1q-id

(Optional) Encapsulation dot1q/bd on which the mac is learnt

ip

ip address

dstip

(Optional) Destination ipv4 address

srcip

(Optional) source ipv4 address

ipv6

(Optional) ipv6 address

port

(Optional) L4 port info

sport

(Optional) Source port

dport

(Optional) Destination port

proto

(Optional) Protocol

proto-id

(Optional) IANA Protocol id

src-intf

(Optional) Interface on which the host with src ip of the payload is connected

src_if

(Optional) Interface

payload-end

(Optional) End payload info input

profile

(Optional) NGOAM profile to use

pid

(Optional) NGOAM profile id

mac

Mac

dmac

Destination mac address

dot1qid

Encapsulation dot1q/bd on which the mac is learnt

dot1qid1

(Optional) Encapsulation dot1q/bd on which the mac is learnt

vrf

(Optional) Display per-VRF information

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

copy-to

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

copy-to-ip

(Optional) IpV4 addr to send responses to

ext-id

(Optional) Identifier passed from caller

ext_id

(Optional) 32-bit identifier

Command Mode

  • /exec

payload

[no] payload

Syntax Description

no

(Optional) Negate a command or set its defaults

payload

Configure ngoam connectivity check payload

Command Mode

  • /exec/configure/configngoamconnectcheck

pcc

[no] pcc

Syntax Description

no

(Optional) Negate a command or set its defaults

pcc

PCC related configuration

Command Mode

  • /exec/configure/sr/te

pce-address ipv4

[no] pce-address ipv4 <ip-address> [ precedence <precedence> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

pce-address

Configure the address of the PCE

ipv4

Configure v4 address of the PCE

precedence

(Optional) Precedence of the PCE

ip-address

PCE address

precedence

(Optional) Path-option preference

Command Mode

  • /exec/configure/sr/te/pcc

pcep

[no] pcep

Syntax Description

no

(Optional) Negate a command or set its defaults

pcep

Dynamic path needs to be computed externally via PCEP

Command Mode

  • /exec/configure/sr/te/color/cndpaths/pref/dyn

pcep

[no] pcep

Syntax Description

no

(Optional) Negate a command or set its defaults

pcep

Dynamic path needs to be computed externally via PCEP

Command Mode

  • /exec/configure/sr/te/pol/cndpaths/pref/dyn

peer-gateway

peer-gateway [ exclude-vlan <vlan-list> ] | no peer-gateway

Syntax Description

no

Negate a command or set its defaults

peer-gateway

Enable L3 forwarding for packets destined to peer's gateway mac-address

exclude-vlan

(Optional) Specify VLANs to be excluded from peer-gateway functionality

vlan-list

(Optional) Specify the list of vlans

Command Mode

  • /exec/configure/vpc-domain

peer-ip

[no] peer-ip { <addr> }

Syntax Description

no

(Optional) Negate a command or set its defaults

peer-ip

Static IP Address Configuration

addr

Remote Peer IP Address

Command Mode

  • /exec/configure/if-nve/vni/ingr-rep

peer-keepalive destination

peer-keepalive destination [ <dst-ip> | <dst-ipv6> ] [ [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | tos-byte <tos-byte-value> | hold-timeout <hold-time-out> ] + | [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | tos { <tos-value> | min-delay | max-throughput | max-reliability | min-monetary-cost | normal } | hold-timeout <hold-time-out> ] + | [ source [ <src-ip> | <src-ipv6> ] | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | precedence { <prec-vlaue> | network | internet | critical | flash-override | flash | immediate | priority | routine } | hold-timeout <hold-time-out> ] + ]

Syntax Description

peer-keepalive

Keepalive/Hello with peer switch

destination

specify destination ip address of peer switch

dst-ip

(Optional) IPv4 address (A.B.C.D) of destination

source

(Optional) source interface for hello

src-ip

(Optional) IPv4 address (A.B.C.D) of source

udp-port

(Optional) enter UDP port number used for hello

udp-port-num

(Optional) udp port number for hellos

vrf

(Optional) vrf to be used for hello messages

vrf-name

(Optional) vrf to be used for hellos

vrf-known-name

(Optional) Known VRF name

interval

(Optional) enter interval in milleseconds

interval-ms

(Optional) Enter interval in milleseconds

timeout

(Optional) enter timeout in seconds

time-out

(Optional) enter timeout in seconds

precedence

(Optional) Precedence

prec-vlaue

(Optional) Precedence value

network

(Optional) network (7)

internet

(Optional) internet (6)

critical

(Optional) critical (5)

flash-override

(Optional) flash-override (4)

flash

(Optional) flash (3)

immediate

(Optional) immediate (2)

priority

(Optional) priority (1)

routine

(Optional) routine (0)

tos

(Optional) Type of Service(IPV4)/Traffic Class(IPV6)

tos-value

(Optional) Enter 4-bit TOS value

min-delay

(Optional) min-delay (8)

max-throughput

(Optional) max-throughput (4)

max-reliability

(Optional) max-reliability (2)

min-monetary-cost

(Optional) min-monetary-cost (1)

normal

(Optional) normal (0)

tos-byte

(Optional) Type of Service Byte (IPv4)/Traffic Class Octet(IPv6)

tos-byte-value

(Optional) Enter 8-bit TOS value

hold-timeout

(Optional) hold timeout to ignore stale peer alive messages

hold-time-out

(Optional) Enter hold-timeout in seconds

Command Mode

  • /exec/configure/vpc-domain

peer-switch

[no] peer-switch

Syntax Description

no

(Optional) Negate a command or set its defaults

peer-switch

Enable peer switch on vPC pair switches

Command Mode

  • /exec/configure/vpc-domain

peer-type fabric

peer-type { fabric-external | fabric-border-leaf } | { no | default } peer-type

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

peer-type

Neighbor facing

fabric-external

Fabric external

fabric-border-leaf

Fabric Border Leaf

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

peer local service

[no] peer local service <service-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

peer

Peer cli for sandwich mode failure notification

local

Peer involved in sandwich mode

service

Peer service involved in sandwich mode

service-name

Peer service name string

Command Mode

  • /exec/configure/itd

peer vpc

[no] peer <svc-name> vpc <num>

Syntax Description

no

(Optional) Negate a command or set its defaults

peer

smart channel peer

vpc

vpc

svc-name

peer smart channel name

num

VPC number to assign to smart-channel

Command Mode

  • /exec/configure/smartc

per-ingress-port-mtu-mode

[no] per-ingress-port-mtu-mode

Syntax Description

no

(Optional) Negate the command

per-ingress-port-mtu-mode

per-ingress-port mtu mode

Command Mode

  • /exec/configure handle auto 424

perf

perf [ { record { context-switch | profile } { system | process <i0> } [ <s1> ] } | { stop { all | <s0> } } | { list } | { create-archive <s2> } | { remove { all | <s3> } } ]

Syntax Description

perf

Run perf tool to collect or process event data

record

(Optional) Record events to a file for later analysis

stop

(Optional) Stop a perf record.

list

(Optional) List recorded datasets

create-archive

(Optional) Create an archive of dataset for download

remove

(Optional) Remove recorded dataset(s)

all

(Optional) Act on all recorded datasets

context-switch

(Optional) Record context-switch events

profile

(Optional) Record periodic runtime samples

system

(Optional) Record events for all processes on all CPUS

process

(Optional) Record events for a specific process with the given pid

i0

(Optional) pid of process to record events

s0

(Optional) id of perf record session to stop

s1

(Optional) id to use for perf record session

s2

(Optional) id of perf dataset to create an archive

s3

(Optional) id of perf dataset to remove

Command Mode

  • /exec

periodic-inventory notification

[no] periodic-inventory notification

Syntax Description

no

(Optional) Negate a command or set its defaults

periodic-inventory

Configure periodic software inventory message dispatch

notification

Enable periodic software inventory message dispatch

Command Mode

  • /exec/configure/callhome

periodic-inventory notification interval

periodic-inventory notification { interval <i0> | timeofday <s0> }

Syntax Description

periodic-inventory

Configure periodic software inventory message dispatch

notification

Enable periodic software inventory message dispatch

interval

Configure the time period for periodic inventory

i0

Time period in days (default is 7 days)

timeofday

Configure the timeofday for periodic inventory in HH:MM format

s0

Time period in HH:MM format

Command Mode

  • /exec/configure/callhome

periodic to

{ [ <seqno> ] | no } periodic { { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday } + | daily | weekdays | weekend } <stime> to <etime>

Syntax Description

seqno

(Optional) Sequence number

no

Negate a command or set its defaults

periodic

Periodic time and date

Monday

Monday

Tuesday

Tuesday

Wednesday

Wednesday

Thursday

Thursday

Friday

Friday

Saturday

Saturday

Sunday

Sunday

daily

Every day of the week

weekdays

Monday thru Friday

weekend

Saturday and Sunday

stime

Starting time

to

Ending day and time

etime

Ending time

Command Mode

  • /exec/configure/timerange

periodic to

{ [ <seqno> ] | no } periodic { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday } <stime> to { <eday> } <etime>

Syntax Description

seqno

(Optional) Sequence number

no

Negate a command or set its defaults

periodic

Periodic time and date

Monday

Monday

Tuesday

Tuesday

Wednesday

Wednesday

Thursday

Thursday

Friday

Friday

Saturday

Saturday

Sunday

Sunday

eday

Day of the week

stime

Starting time

to

Ending day and time

etime

Ending time

Command Mode

  • /exec/configure/timerange

permit interface

[no] permit interface <if0>

Syntax Description

no

(Optional) Negate a command or set its defaults

permit

Permit access to interfaces (applicable if interface policy is 'deny')

interface

Enter the range of interfaces accessible the role

if0

Enter the interface range

Command Mode

  • /exec/configure/role/interface

permit vlan

[no] permit vlan <vlan-mrange>

Syntax Description

no

(Optional) Negate a command or set its defaults

permit

Permit access to vlans (applicable if vlan policy is 'deny')

vlan

Enter the range of vlans accessible the role

vlan-mrange

Enter the vlan range

Command Mode

  • /exec/configure/role/vlan

permit vrf

[no] permit vrf <vrf-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

permit

Permit access to vrf (applicable if vrf policy is 'deny')

vrf

Enter the range of vrf accessible the role

vrf-name

Enter the vrf name

Command Mode

  • /exec/configure/role/vrf

permit vsan

[no] permit vsan <vsan-mrange>

Syntax Description

no

(Optional) Negate a command or set its defaults

permit

Permit access to vsans (applicable if vsan policy is 'deny')

vsan

Enter the range of vsans accessible the role

vsan-mrange

Enter the vsan range

Command Mode

  • /exec/configure/role/vsan

personality

[no] personality

Syntax Description

no

(Optional) Negate a mode

personality

Config Personality

Command Mode

  • /exec/configure

personality backup

personality backup { <uri_local> | <uri_remote> [ password <password> ] [ vrf <vrf-known-name> ] }

Syntax Description

personality

personality

backup

backup personality

password

(Optional) The password for personality backups

vrf

(Optional) The VRF for personality backups

uri_local

Personality backup local destination

uri_remote

Personality backup remote destination

password

(Optional) Password for SCP username

vrf-known-name

(Optional) VRF name

Command Mode

  • /exec

personality restore

personality restore <uri> [ user-name <user> ] [ password <password> ] [ hostname <hostname> ] [ vrf <vrf_name> ]

Syntax Description

personality

Personality

restore

Restore the personality file

uri

Personality file

user-name

(Optional) The username for downloads

user

(Optional) The username

password

(Optional) The password for downloads

password

(Optional) The password

hostname

(Optional) The hostname for downloads

hostname

(Optional) The hostname

vrf

(Optional) The VRF for downloads

vrf_name

(Optional) The VRF name

Command Mode

  • /exec

phone-contact

{ phone-contact <s0> | no phone-contact }

Syntax Description

no

Negate a command or set its defaults

phone-contact

Contact person's phone number

s0

Phone number in international format(such as +1-800-123-4567)

Command Mode

  • /exec/configure/callhome

pim

[no] pim

Syntax Description

no

(Optional) Negate a command or set its defaults

pim

Policies for a Remote Receiver

Command Mode

  • /exec/configure/nbm-vrf/nbm-host-policy

pim

[no] pim

Syntax Description

no

(Optional) Negate a command or set its defaults

pim

Policies for a Remote Receiver

Command Mode

  • /exec/configure/nbm-host-policy

ping

ping [ { { <alpha> | <numeric> [ loopback interface <interface> ] } | { multicast <group> interface <interface> [ loopback ] } } [ [ source-interface <src-intf> | vrf { <vrf-name> | <vrf-known-name> } ] [ count { <count> | unlimited } | packet-size <packetsize> | vrf { <vrf-name> | <vrf-known-name> } | interval <interval> | source { <alpha> | <numeric1> } | df-bit | timeout <timeout> ] + | [ count { <count> | unlimited } | packet-size <packetsize> | source-interface <src-intf> | interval <interval> | df-bit | timeout <timeout> ] + ] ]

Syntax Description

ping

Test

count

(Optional) Number

unlimited

(Optional) Unlimited

count

(Optional) Number

packet-size

(Optional) Packet

packetsize

(Optional) Size

source-interface

(Optional) Select source interface

src-intf

(Optional) Specify interface

interval

(Optional) Wait

interval

(Optional) Interval

numeric

(Optional) IP address of remote system

numeric1

(Optional) IP

alpha

(Optional) Enter

multicast

(Optional) Multicast

group

(Optional) Multicast

interface

(Optional) Interface

interface

(Optional) Interface

loopback

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

source

(Optional) Source

df-bit

(Optional) Enable

timeout

(Optional) Specify

timeout

(Optional) Timeout

vrf

(Optional) Display per-VRF information

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

Command Mode

  • /exec

ping6

ping6 { { <host> | <hostname> } | { multicast <group> } } [ [ { count { <count> | unlimited } } | { packet-size <packetsize> } | [ source { <host1> | <hostname> } ] | vrf { <vrf-name> | <vrf-known-name> } | timeout <timeout> | { interval <interval> } ] + | [ { count { <count> | unlimited } } | { packet-size <packetsize> } | { source-interface <src-intf> } | timeout <timeout> | { interval <interval> } ] + ]

Syntax Description

ping6

Test

count

(Optional) Number

count

(Optional) Number

unlimited

(Optional) unlimited

packet-size

(Optional) Packet

packetsize

(Optional) Size

source-interface

(Optional) Select source interface

src-intf

(Optional) Specify interface

interval

(Optional) Wait

interval

(Optional) Interval

hostname

Enter

multicast

Multicast

vrf

(Optional) Display per-VRF information

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

source

(Optional) Source

timeout

(Optional) Specify

timeout

(Optional) Timeout

Command Mode

  • /exec

ping mpls

ping mpls { nil-fec { { labels <comma-separated-labels> } { output { ointerface <tx-interface> } nexthop <nexthop-ip-addr> } | { policy { { name <srte-policy-name> } | { endpoint <srte-policy-endpoint> color <srte-policy-color> } } [ { output { ointerface <tx-interface> } [ nexthop <nexthop-ip-addr> ] } ] } } } [ { repeat <count> } | { { size <size> } | { sweep <min-size> <max-size> <increment> } } | { timeout <seconds> } | { interval <milliseconds> } | { destination <addr-start> [ <addr-end> [ <addr-incr-mask> | <addr-incr> ] ] } | { source <addr> } | { exp <exp-value> } | { pad <pattern> } | { ttl <ttl> } | { verbose } | { reply { { mode { <reply-mode-ipv4> | router-alert | control-channel | no-reply } } | { dscp { <dscp-bits> | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | default | ef } } | { pad-tlv } } } + | { force-explicit-null } | { dsmap [ hashkey { none | { hash-ipv4 { bitmap <bitmap-size> } } } ] } | { flags { fec } } ] +

Syntax Description

ping

need

mpls

Test

nil-fec

Target

labels

A

comma-separated-labels

A

repeat

(Optional) Repeat

count

(Optional) Repeat

size

(Optional) Packet

size

(Optional) Datagram

sweep

(Optional) Sweep

min-size

(Optional)

max-size

(Optional)

increment

(Optional) Sweep

timeout

(Optional) Timeout

seconds

(Optional) Timeout

interval

(Optional) Send

milliseconds

(Optional) Send

destination

(Optional) Destination

addr-start

(Optional) Destination

addr-end

(Optional) Destination

addr-incr-mask

(Optional) Destination

addr-incr

(Optional) Destination

source

(Optional) Source

addr

(Optional) Source

exp

(Optional) EXP

exp-value

(Optional) EXP

pad

(Optional) Pad

pattern

(Optional) Pad

ttl

(Optional) Time

ttl

(Optional) TTL

verbose

(Optional) verbose

reply

(Optional) Reply

mode

(Optional) Reply

reply-mode-ipv4

(Optional) Send

router-alert

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

control-channel

(Optional) Send

no-reply

(Optional) Send

dscp

(Optional) DSCP

dscp-bits

(Optional) Differentiated

af11

(Optional) Match

af12

(Optional) Match

af13

(Optional) Match

af21

(Optional) Match

af22

(Optional) Match

af23

(Optional) Match

af31

(Optional) Match

af32

(Optional) Match

af33

(Optional) Match

af41

(Optional) Match

af42

(Optional) Match

af43

(Optional) Match

cs1

(Optional) Match

cs2

(Optional) Match

cs3

(Optional) Match

cs4

(Optional) Match

cs5

(Optional) Match

cs6

(Optional) Match

cs7

(Optional) Match

default

(Optional) Match

ef

(Optional) Match

pad-tlv

(Optional) Reply

force-explicit-null

(Optional) Force

output

Output

ointerface

Echo

tx-interface

Echo

nexthop

Next

nexthop-ip-addr

Next

dsmap

(Optional) Request

hashkey

(Optional) Downstream

none

(Optional) Hash

hash-ipv4

(Optional) IPv4

bitmap

(Optional) Hash

bitmap-size

(Optional) Multipath

flags

(Optional) Flag

fec

(Optional) Request

policy

Derive

name

Specify

color

Specify

endpoint

Specify

srte-policy-name

The

srte-policy-color

The

srte-policy-endpoint

The

Command Mode

  • /exec

ping nve

ping nve { { { { { ip { <numeric10> | <numeric11> | unknown } } [ vrf { <vrf-name> | <vrf-known-name> } | { <dot1qid1> } ] } | mac <dmac> <dot1qid> [ <intfid> ] } [ profile <pid> ] } [ payload { [ mac-addr <dstmac> <smac> ] [ dot1q <dot1q-id> ] [ ip <dstip> <srcip> | ipv6 <dstipv6> <srcipv6> ] [ port <sport> <dport> ] [ proto <proto-id> ] [ src-intf <src_if> ] } payload-end ] [ source { <numeric1> | <numeric2> } |

Syntax Description

{

<count>

ping

Test

nve

network virtualization edge

numeric10

Ipv4 address of remote host / VTEP

unknown

Peer vtep ip is unknown, Applicable only for channel Nv03

dot1qid

Encapsulation dot1q/bd on which the mac is learnt

intfid

(Optional) Name of the interface for ngoam ping on which dot1q is configured

payload

(Optional) Enter customer payload

port

(Optional) L4 port info

sport

(Optional) Source port

dport

(Optional) Destination port

proto

(Optional) Protocol

proto-id

(Optional) IANA Protocol id

src-intf

(Optional) Interface on which the host with src ip of the payload is connected

src_if

(Optional) Interface

payload-end

(Optional) End of payload info

profile

(Optional) NGOAM profile to use

pid

(Optional) NGOAM profile id

mac

Mac

mac-addr

(Optional) Mac

ip

ip address

dstip

(Optional) Destination ipv4 address

srcip

(Optional) source ipv4 address

ipv6

(Optional) ipv6 address

dmac

Destination mac address

dstmac

(Optional) Destination mac address

smac

(Optional) Source mac address

dot1q

(Optional) Encapsulation dot1q/bd

dot1q-id

(Optional) Encapsulation dot1q/bd on which the mac is learnt

dot1qid1

(Optional) Encapsulation dot1q/bd on which the mac is learnt

vrf

(Optional) Display per-VRF information

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

source

(Optional) Source

numeric1

(Optional) IP

Command Mode

  • /exec

ping sr-mpls

ping sr-mpls { <sr-ipv4-prefix> fec-type { { igp isis } | { bgp } | { generic } } } [ { repeat <count> } | { { size <size> } | { sweep <min-size> <max-size> <increment> } } | { timeout <seconds> } | { interval <milliseconds> } | { destination <addr-start> [ <addr-end> [ <addr-incr-mask> | <addr-incr> ] ] } | { source <addr> } | { exp <exp-value> } | { pad <pattern> } | { ttl <ttl> } | { verbose } | { reply { { mode { <reply-mode-ipv4> | router-alert | control-channel | no-reply } } | { dscp { <dscp-bits> | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | default | ef } } | { pad-tlv } } } + | { force-explicit-null } | { dsmap [ hashkey { none | { hash-ipv4 { bitmap <bitmap-size> } } } ] } | { flags { fec } } ] +

Syntax Description

ping

need

sr-mpls

Test

sr-ipv4-prefix

IP

fec-type

Type

igp

Kind

isis

ISIS

bgp

BGP

generic

Generic

repeat

(Optional) Repeat

count

(Optional) Repeat

size

(Optional) Packet

size

(Optional) Datagram

sweep

(Optional) Sweep

min-size

(Optional)

max-size

(Optional)

increment

(Optional) Sweep

timeout

(Optional) Timeout

seconds

(Optional) Timeout

interval

(Optional) Send

milliseconds

(Optional) Send

destination

(Optional) Destination

addr-start

(Optional) Destination

addr-end

(Optional) Destination

addr-incr-mask

(Optional) Destination

addr-incr

(Optional) Destination

source

(Optional) Source

addr

(Optional) Source

exp

(Optional) EXP

exp-value

(Optional) EXP

pad

(Optional) Pad

pattern

(Optional) Pad

ttl

(Optional) Time

ttl

(Optional) TTL

verbose

(Optional) verbose

reply

(Optional) Reply

mode

(Optional) Reply

reply-mode-ipv4

(Optional) Send

router-alert

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

control-channel

(Optional) Send

no-reply

(Optional) Send

dscp

(Optional) DSCP

dscp-bits

(Optional) Differentiated

af11

(Optional) Match

af12

(Optional) Match

af13

(Optional) Match

af21

(Optional) Match

af22

(Optional) Match

af23

(Optional) Match

af31

(Optional) Match

af32

(Optional) Match

af33

(Optional) Match

af41

(Optional) Match

af42

(Optional) Match

af43

(Optional) Match

cs1

(Optional) Match

cs2

(Optional) Match

cs3

(Optional) Match

cs4

(Optional) Match

cs5

(Optional) Match

cs6

(Optional) Match

cs7

(Optional) Match

default

(Optional) Match

ef

(Optional) Match

pad-tlv

(Optional) Reply

force-explicit-null

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

dsmap

(Optional) Request

hashkey

(Optional) Downstream

none

(Optional) Hash

hash-ipv4

(Optional) IPv4

bitmap

(Optional) Hash

bitmap-size

(Optional) Multipath

flags

(Optional) Flag

fec

(Optional) Request

Command Mode

  • /exec

plb

[no] plb [ <svc-name> ] [ service <service-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

plb

Configure PLB

svc-name

(Optional) Specify PLB service name [Deprecated]

service

(Optional) Configure PLB service [Preferred]

service-name

(Optional) Specify PLB service name

Command Mode

  • /exec/configure

plb analytics

[no] plb analytics <service-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

plb

Configure PLB

analytics

Enable PLB service analytics

service-name

PLB service name

Command Mode

  • /exec/configure

plb device-group

[no] plb device-group <group-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

plb

Configure PLB

device-group

Configure PLB device group

group-name

Specify device-group name

Command Mode

  • /exec/configure

pnp startup-vlan

[no] pnp startup-vlan <vlan>

Syntax Description

no

(Optional) disable pnp startup vlan configured. default value is vlan 1

pnp

plug and play

startup-vlan

PnP startup-vlan

vlan

PNP vlan id. Default vlan is 1

Command Mode

  • /exec/configure

police

[no] police [ { { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ] <bc-val> [ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] | percent1 <pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform { <opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> | <opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed { <opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate { <opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } } ]

Syntax Description

no

Negate a command or set its defaults

police

Police

cir

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

opt_kbps_mbps_gbps_pps_cir

(Optional) Units

percent

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

pir

(Optional) Specify peak information rate

opt_kbps_mbps_gbps_pps_pir

(Optional) Units

percent1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

be

(Optional) Specify extended burst

opt_kbytes_mbytes_gbytes_be

(Optional) Units

bc

(Optional) Specify committed burst

opt_kbytes_mbytes_gbytes_bc

(Optional) Units

conform

(Optional) Specify a conform action

opt_drop_transmit_conform

(Optional) Set the action

set-cos-transmit

(Optional) Set conform action cos val

set-cos-val

(Optional) 802.1Q Class of Service value

set-dscp-transmit

(Optional) Set conform action dscp val

set-dscp-val

(Optional) DSCP value

opt_set_dscp

(Optional)

set-prec-transmit

(Optional) Set conform action precedence val

set-prec-val

(Optional) IP Precedence value

opt_set_prec

(Optional)

exceed

(Optional) Specify a exceed action

opt_drop_transmit_exceed

(Optional) Set the action

set

(Optional) Set exceed action to cir-markdown-map

dscp1

(Optional) Exceed from field

dscp2

(Optional) Exceed to field

table

(Optional) To specify table name

cir-markdown-map

(Optional) Well known markdown map

violate

(Optional) Specify a violate action

opt_drop_transmit_violate

(Optional) Set the action

set1

(Optional) Set violate action to pir-markdown-map

dscp3

(Optional) Violate from field

dscp4

(Optional) Violate to field

table1

(Optional) To specify table name

pir-markdown-map

(Optional) Well known markdown map

Command Mode

  • /exec/configure/pmap/class

police

[no] police { { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps ] | percent <cir-perc> } [ [ bc ] { <committed-burst> [ bytes | kbytes | mbytes | ms | us ] } ] [ pir { <pir-val> [ bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent <pir-perc> } [ [ be ] { <extended-burst> [ bytes2 | kbytes2 | mbytes2 | ms2 | us2 | packets2 ] } ] ] [ conform { transmit | set-prec-transmit { <prec-val> | <prec-enum> } | set-dscp-transmit { <dscp-val> | <dscp-enum> } | set-cos-transmit <cos-val> | set-discard-class-transmit <disc-class-val> | set-qos-transmit <qos-grp-val> | set-mpls-exp-imposition-transmit <exp-value-imp> | set-mpls-exp-topmost-transmit <exp-value-top> } [ exceed { drop1 | set <exc-frm-field> <exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1> | <prec-enum1> } | set-dscp-transmit1 { <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> | set-discard-class-transmit1 <disc-class-val1> | set-qos-transmit1 <qos-grp-val1> | set-mpls-exp-imposition-transmit1 <exp-value-imp1> | set-mpls-exp-topmost-transmit1 <exp-value-top1> } ] [ violate { drop2 | set <vio-frm-field> <vio-to-field> table2 pir-markdown-map | set-prec-transmit2 { <prec-val2> | <prec-enum2> } | set-dscp-transmit2 { <dscp-val2> | <dscp-enum2> } | set-cos-transmit2 <cos-val2> | set-discard-class-transmit2 <disc-class-val2> | set-qos-transmit2 <qos-grp-val2> | set-mpls-exp-imposition-transmit2 <exp-value-imp2> | set-mpls-exp-topmost-transmit2 <exp-value-top2> } ] ] } | aggregate <policer-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

police

police

cir

(Optional) Specify committed information rate

bc

(Optional) Specify committed burst

percent

Specify rate as percentage of interface data-rate

cir-perc

Percentage

pir-perc

(Optional) Percentage

pir

(Optional) Specify peak information rate

be

(Optional) Specify extended burst (for 1R3C meter)

bps

(Optional) Bits per second

kbps

(Optional) Kilo bits per second

mbps

(Optional) Mega bits per second

gbps

(Optional) Giga bits per second

bps2

(Optional) Bits per second

kbps2

(Optional) Kilo Bits per second

mbps2

(Optional) Mega Bits per second

gbps2

(Optional) Giga Bits per second

pps2

(Optional) Packets per second

bytes

(Optional) Bytes

kbytes

(Optional) Kilo bytes

mbytes

(Optional) Mega bytes

us

(Optional) Micro second(s)

ms

(Optional) Milli second(s)

bytes2

(Optional) Bytes

kbytes2

(Optional) Kilo Bytes

mbytes2

(Optional) Mega Bytes

ms2

(Optional) Milli seconds

us2

(Optional) Micro seconds

packets2

(Optional) Packets

conform

(Optional) Specify a conform action

exceed

(Optional) Specify a exceed action

violate

(Optional) Specify a violate action

transmit

(Optional) Transmit packet

drop1

(Optional) Drop packet

drop2

(Optional) Drop packet

set-prec-transmit

(Optional) Set precedence and send it

set-prec-transmit1

(Optional) Set precedence and send it

set-prec-transmit2

(Optional) Set precedence and send it

prec-val

(Optional) Precedence value

prec-val1

(Optional) Precedence value

prec-val2

(Optional) Precedence value

prec-enum

(Optional)

prec-enum1

(Optional)

prec-enum2

(Optional)

set-dscp-transmit

(Optional) Set dscp and send it

set-dscp-transmit1

(Optional) Set dscp and send it

set-dscp-transmit2

(Optional) Set dscp and send it

dscp-val

(Optional) DSCP value

dscp-val1

(Optional) DSCP value

dscp-val2

(Optional) DSCP value

dscp-enum

(Optional)

dscp-enum1

(Optional)

dscp-enum2

(Optional)

set-cos-transmit

(Optional) Set cos and send it

set-cos-transmit1

(Optional) Set cos and send it

set-cos-transmit2

(Optional) Set cos and send it

cos-val

(Optional) new cos value

cos-val1

(Optional) new cos value

cos-val2

(Optional) new cos value

set-discard-class-transmit

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-discard-class-transmit1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-discard-class-transmit2

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

disc-class-val

(Optional) new discard-class value

disc-class-val1

(Optional) new discard-class value

disc-class-val2

(Optional) new discard-class value

set-qos-transmit

(Optional) Set qos-group and send it

set-qos-transmit1

(Optional) Set qos-group and send it

set-qos-transmit2

(Optional) Set qos-group and send it

qos-grp-val

(Optional) QoS group value

qos-grp-val1

(Optional) QoS group value

qos-grp-val2

(Optional) QoS group value

set-mpls-exp-imposition-transmit

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-mpls-exp-imposition-transmit1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-mpls-exp-imposition-transmit2

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

exp-value-imp

(Optional) MPLS imposition value

exp-value-imp1

(Optional) MPLS imposition value

exp-value-imp2

(Optional) MPLS imposition value

set-mpls-exp-topmost-transmit

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-mpls-exp-topmost-transmit1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

set-mpls-exp-topmost-transmit2

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

exp-value-top

(Optional) MPLS topmost value

exp-value-top1

(Optional) MPLS topmost value

exp-value-top2

(Optional) MPLS topmost value

set

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

exc-frm-field

(Optional)

exc-to-field

(Optional)

vio-frm-field

(Optional)

vio-to-field

(Optional)

table

(Optional) Set using the table-map

table2

(Optional) Set using the table-map

cir-markdown-map

(Optional) Markdown map table name for exceed action

pir-markdown-map

(Optional) Markdown map table name for violate action

aggregate

Choose aggregate policer for current class

policer-name

Enter aggregate-policer name

Command Mode

  • /exec/configure/policy-map/class

policer

[no] policer

Syntax Description

no

(Optional) Negate a command or set its defaults

policer

Flow rate limiter installed in hardware

Command Mode

  • /exec/configure/nbm-vrf/nbm-flow-policy/attr

policer

[no] policer

Syntax Description

no

(Optional) Negate a command or set its defaults

policer

Flow rate limiter installed in hardware

Command Mode

  • /exec/configure/nbm-flow-policy/attr

policy-map

[no] policy-map [ type qos ] [ match-first ] <pmap-name-qos>

Syntax Description

no

(Optional) Negate a command or set its defaults

policy-map

Configure a policy map

type

(Optional) Specify the type of this policy-map

qos

(Optional) Qos policy

match-first

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

pmap-name-qos

Policy-map name (alphanumeric)

Command Mode

  • /exec/configure

policy-map type control-plane

[no] policy-map type control-plane <pmap-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

policy-map

Configure a policy map

type

Specify the type of this policy-map

control-plane

Control-Plane

pmap-name

Policy-map name (alphanumeric)

Command Mode

  • /exec/configure

policy-map type network-qos

[no] policy-map type network-qos <pmap-name-nq>

Syntax Description

no

(Optional) Negate a command or set its defaults

policy-map

Configure a policy map

type

Specify the type of this policy-map

network-qos

Network QoS policy

pmap-name-nq

Policy-map name

Command Mode

  • /exec/configure

policy-map type queuing

[no] policy-map type queuing [ match-first ] <pmap-name-que>

Syntax Description

no

(Optional) Negate a command or set its defaults

policy-map

Configure a policy map

type

Specify the type of this policy-map

queuing

Queuing policy

match-first

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

pmap-name-que

Policy-map name (alphanumeric)

Command Mode

  • /exec/configure

policy

[no] policy { <cfg-pol-name> | <unknown-pol-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

policy

NBM Flow policy

cfg-pol-name

Policy name

unknown-pol-name

Policy name

Command Mode

  • /exec/configure/nbm-flow-policy

policy

policy { { dynamic identity <device-id> } | { static sgt <sgt> [ trusted ] } } | no policy static | no policy dynamic

Syntax Description

policy

Enable and define policy to be applied

dynamic

apply to authorization server for policy

identity

specify identity of peer for authorization request

device-id

peer's device-id

static

configure static policy

sgt

SGT tag for pkts from this device

sgt

sgt value

trusted

(Optional) specify trust state of the link

Command Mode

  • /exec/configure/cts-manual

policy

[no] policy <pol-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

policy

Identifying name for policy with max 128 characters

pol-name

Configure Policy name

Command Mode

  • /exec/configure/sr/te

policy

[no] policy { <cfg-pol-name> | <unknown-pol-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

policy

NBM Flow policy

cfg-pol-name

Policy name

unknown-pol-name

Policy name

Command Mode

  • /exec/configure/nbm-vrf/nbm-flow-policy

pop

pop [ <name> ]

Syntax Description

pop

pop mode from stack or restore from name

name

(Optional) name

Command Mode

  • /global

port-channel fast-convergence

port-channel fast-convergence | no port-channel fast-convergence

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

fast-convergence

Enable/Disable port-channel fast convergence

Command Mode

  • /exec/configure

port-channel hash-distribution

port-channel hash-distribution <type> | no port-channel hash-distribution [ <type> ]

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

hash-distribution

Configure port-channel hash-distribution

type

adaptive/fixed (default adaptive)

Command Mode

  • /exec/configure/

port-channel limit

port-channel limit | no port-channel limit

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure the maximum number of supported vPCs

limit

limit to 244 vPCs

Command Mode

  • /exec/configure/vpc-domain

port-channel load-balance1 ethernet

port-channel load-balance1 ethernet <algorithm> [ symmetric ] | no port-channel load-balance1 ethernet [ <algorithm> [ symmetric ] ]

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

load-balance1

Configure port-channel load balance

ethernet

Ethernet port-channel

algorithm

Configure port-channel load balance

symmetric

(Optional) symmetric load balancing

Command Mode

  • /exec/configure

port-channel load-balance2 resilient

port-channel load-balance2 resilient | no port-channel load-balance2 resilient

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

load-balance2

Configure port-channel load balance

resilient

Configure port-channel load balance resilient mode

Command Mode

  • /exec/configure

port-channel load-defer

port-channel load-defer <load-defer-timeout> | no port-channel load-defer [ <load-defer-timeout> ]

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

load-defer

Load defer time interval

load-defer-timeout

Load defer time interval in seconds (default 120 seconds)

Command Mode

  • /exec/configure/

port-channel port hash-distribution

port-channel port hash-distribution <type> | no port-channel port hash-distribution [ <type> ]

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

port

Configure port-channel port hash-distribution

hash-distribution

Configure port-channel port hash-distribution

type

adaptive/fixed (default adaptive)

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

port-channel port load-defer

port-channel port load-defer | no port-channel port load-defer

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

port

Configure port-channel load-defer for member ports

load-defer

Configure port-channel load-defer

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

port-channel scale-fanout

port-channel scale-fanout | no port-channel scale-fanout

Syntax Description

no

Negate a command or set its defaults

port-channel

Configure port channel parameters

scale-fanout

Enable/disable port-channel scale-fanout when ports span more than 16 ASIC units

Command Mode

  • /exec/configure

port-group

{ port-group <name> } | { no port-group <name> }

Syntax Description

no

Negate a command or set its defaults

port-group

smart channel port group

name

smart channel port group name

Command Mode

  • /exec/configure/smartc

port-license

[no] port-license [ acquire ]

Syntax Description

no

(Optional) Negate a command or set its defaults

port-license

Enable port activation license

acquire

(Optional) Acquire port activation license

Command Mode

  • /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext

port-license

[no] port-license [ acquire ]

Syntax Description

no

(Optional) Negate a command or set its defaults

port-license

Enable port activation license

acquire

(Optional) Acquire port activation license

Command Mode

  • /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext

port-profile

[no] port-profile [ type <typeval> ] { <profilename> | <s0> }

Syntax Description

no

(Optional) Negate a command or set its defaults

port-profile

Configure a port-profile

profilename

Enter the name of the profile

s0

Enter the name of the profile

type

(Optional) configure type of the profile

typeval

(Optional)

Command Mode

  • /exec/configure

port-type

[no] port-type <type>

Syntax Description

no

(Optional) Negate a command or set its defaults

port-type

Identifies if port is fabric-facing or not

type

Facing port-type

Command Mode

  • /exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-ether-sub-p2p

port

{ port <sport> <dport> }

Syntax Description

port

L4 port info

sport

Source port

dport

Destination port

Command Mode

  • /exec/configure/configngoamccpayload

port

{ no port | port <value> }

Syntax Description

no

port

Port on which to listen

value

Max port value

Command Mode

  • /exec/configure/config-twamp-srvr

port

{ { [ no ] port <i0> } | { no port } }

Syntax Description

no

(Optional) Negate a command or set its defaults

port

Specify port on which local radius server listens

i0

Radius server port (default is 1700)

Command Mode

  • /exec/configure/locsvr-da-radius

port control

[no] port control <port-control-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

port

Configure PLB port control

control

control

port-control-name

Port control name

Command Mode

  • /exec/configure/plb-inout

port destination

{ port { destination | source } <port> } | { no port { destination | source } }

Syntax Description

no

Negate a command or set its defaults

port

specify flow port address

source

specify flow source port address

destination

specify flow destination port address

port

port number

Command Mode

  • /exec/configure/configngoamprofileflow

port type ethernet

[no] port <port-range> type { ethernet | fc }

Syntax Description

no

(Optional) Negate a command or set its defaults

port

Configure a port

port-range

Enter a port range

type

Configure a port type

ethernet

Ethernet Port

fc

FC Port

Command Mode

  • /exec/configure/slot

postcard-telemetry exporter

[no] postcard-telemetry exporter <exportername>

Syntax Description

postcard-telemetry

Enable/Disable postcard telemetry configuration

exporter

Define a events Exporter

exportername

Name of event Exporter

Command Mode

  • /exec/configure/config-postcard

postcard-telemetry flow-profile

[no] postcard-telemetry flow-profile

Syntax Description

postcard-telemetry

Enable/Disable postcard telemetry configuration

flow-profile

Define a POSTCARD flow-profile

Command Mode

  • /exec/configure/config-postcard

postcard-telemetry monitor

[no] postcard-telemetry monitor <monitorname>

Syntax Description

postcard-telemetry

Enable/Disable postcard telemetry configuration

monitor

Define a POSTCARD Monitor

monitorname

Name of POSTCARD Monitor

Command Mode

  • /exec/configure/config-postcard

postcard-telemetry queue-profile

[no] postcard-telemetry queue-profile [ <queue_profilename> | queue-profile-default ]

Syntax Description

postcard-telemetry

Enable/Disable postcard telemetry configuration

queue-profile

Define a POSTCARD queue_profile

queue_profilename

(Optional) Name of POSTCARD queue_profile

queue-profile-default

(Optional) Queue Profile Default Configuration

Command Mode

  • /exec/configure/config-postcard

postcard-telemetry system monitor

[no] postcard-telemetry system monitor <monitorname>

Syntax Description

system

global config

postcard-telemetry

postcard global settings

monitor

postcard Monitor to be applied

monitorname

postcard Monitor to be applied

Command Mode

  • /exec/configure/config-postcard

postcard-telemetry watchlist ip

[no] postcard-telemetry watchlist ip <watchlistname>

Syntax Description

postcard-telemetry

Enable/Disable postcard telemetry configuration

watchlist

Define a POSTCARD watchlist

ip

Configure POSTCARD IP watchlist

watchlistname

Name of POSTCARD watchlist

Command Mode

  • /exec/configure/config-postcard

power efficient-ethernet auto

[no] power efficient-ethernet auto

Syntax Description

no

(Optional) Negate a command or set its defaults

power

Configure EEE for the port

efficient-ethernet

Configure Energy Efficient Ethernet (EEE)

auto

Auto negotiate EEE

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

power efficient-ethernet sleep threshold aggressive

[no] power efficient-ethernet sleep threshold aggressive

Syntax Description

no

(Optional) Negate a command or set its defaults

power

Configure EEE for the port

efficient-ethernet

Configure Energy Efficient Ethernet (EEE)

sleep

EEE LPI sleep configuration

threshold

EEE LPI sleep threshold

aggressive

Enable/ Disable EEE LPI aggressive sleep mode

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

power inline

{ power inline { <port-mode-never> | <port-mode> [ max <wattage> ] } } | { no power inline { <port-mode-never> | <port-mode> } }

Syntax Description

no

Negate a command or set its defaults

power

Power over Ethernet

port-mode-never

configure POE port mode

port-mode

configure POE port mode

max

(Optional) Configure the max power per interface

wattage

(Optional) milli-watts

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

power inline default_consumption

{ power inline default_consumption <wattage> } | { no power inline default_consumption }

Syntax Description

no

Negate a command or set its defaults

power

Power over Ethernet

default_consumption

POE port default consumption

wattage

milli-watts

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

power inline police action

{ power inline police action <police-action> } | { no power inline police action }

Syntax Description

no

Negate a command or set its defaults

power

Power over Ethernet

police

Configure POE port police parameters

action

Configure action in port when power allocation exceeds

police-action

configure POE port action

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

power inline port priority

{ power inline port priority <port-priority> } | { no power inline port priority <port-priority> }

Syntax Description

no

Negate a command or set its defaults

power

Power over Ethernet

port

Configure POE port parameters

priority

Configure the priority for the port

port-priority

configure POE port priority

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

power redundancy-mode ps-redundant

[no] power redundancy-mode ps-redundant

Syntax Description

no

(Optional) Negate a command or set its defaults

power

Configure power supply

redundancy-mode

Configure power supply redundancy mode

ps-redundant

Configure power supply redundancy mode as PS redundant

Command Mode

  • /exec/configure

precision milliseconds

{ { no | default } precision | precision { milliseconds | microseconds } }

Syntax Description

no

precision

milliseconds

default

Set a command to its defaults

precision

Set precision of measurement

microseconds

Precision microseconds

milliseconds

Precision milliseconds

Command Mode

  • /exec/configure/ip-sla/jitter

preempt

[no] preempt

Syntax Description

no

(Optional) Negate a command or set its defaults

preempt

Enable preemption of lower priority master

Command Mode

  • /exec/configure/if-eth-any/vrrp

preempt

[no] preempt | preempt

Syntax Description

no

Negate a command or set its defaults

preempt

Enable preemption of lower priority Master

Command Mode

  • /exec/configure/if-eth-any/vrrpv3

preempt delay minimum

[no] preempt delay | preempt delay minimum <secs>

Syntax Description

no

Negate a command or set its defaults

preempt

Enable preemption of lower priority Master

delay

Wait before preempting

minimum

Delay at least this long

secs

Seconds to delay

Command Mode

  • /exec/configure/if-eth-any/vrrpv3

preempt delay minimum reload sync preempt delay reload minimum sync preempt delay sync minimum reload preempt delay reload sync minimum preempt delay sync reload minimum preempt delay minimum sync reload preempt delay reload sync preempt delay sync reload preempt delay minimum sync preempt delay sync minimum preempt delay minimum reload preempt delay reload minimum preempt delay minimum preempt delay reload preempt delay sync preempt

preempt delay minimum <min-delay> reload <rel-delay> sync <sync-delay> | preempt delay reload <rel-delay> minimum <min-delay> sync <sync-delay> | preempt delay sync <sync-delay> minimum <min-delay> reload <rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> minimum <min-delay> | preempt delay sync <sync-delay> reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> sync <sync-delay> reload <rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> | preempt delay sync <sync-delay> reload <rel-delay> | preempt delay minimum <min-delay> sync <sync-delay> | preempt delay sync <sync-delay> minimum <min-delay> | preempt delay minimum <min-delay> reload <rel-delay> | preempt delay reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> | preempt delay reload <rel-delay> | preempt delay sync <sync-delay> | preempt | no preempt | no preempt delay [ { minimum [ <min-delay> ] [ [ reload [ <rel-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [ <sync-delay> ] ] [ reload [ <rel-delay> ] ] ] | reload [ <rel-delay> ] [ [ minimum [ <min-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [ <sync-delay> ] ] [ minimum [ <min-delay> ] ] ] | sync [ <sync-delay> ] [ [ reload [ <rel-delay> ] ] [ minimum [ <min-delay> ] ] | [ minimum [ <min-delay> ] ] [ reload [ <rel-delay> ] ] ] } ]

Syntax Description

no

Negate a command or set its defaults

preempt

Overthrow lower priority Active routers

delay

Wait before preempting

minimum

Delay at least this long

min-delay

Number of seconds for minimum delay

reload

Delay after reload

rel-delay

Number of seconds for reload delay

sync

Wait for IP redundancy clients

sync-delay

Number of seconds for sync delay

Command Mode

  • /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6

preference

[no] preference <pref>

Syntax Description

no

(Optional) Negate a command or set its defaults

preference

Policy path-option preference entry

pref

Path-option preference

Command Mode

  • /exec/configure/sr/te/pol/cndpaths

preference

[no] preference <pref>

Syntax Description

no

(Optional) Negate a command or set its defaults

preference

Candidate path-option preference entry

pref

Path-option preference

Command Mode

  • /exec/configure/sr/te/color/cndpaths

preference max

[no] preference max <pref-val>

Syntax Description

no

(Optional) Negate a command or set its defaults

pref-val

maximum value

Command Mode

  • /exec/configure/config-dhcp-guard

preference min

[no] preference min <pref-val>

Syntax Description

no

(Optional) Negate a command or set its defaults

pref-val

maximum value

Command Mode

  • /exec/configure/config-dhcp-guard

prefix out

[ no | default ] { prefix-list <prfxlist-name> } { out | in }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

prefix-list

Apply prefix-list

prfxlist-name

Name of prefix-list

out

Apply policy to outgoing routes

in

Apply policy to incoming routes

Command Mode