L Commands

l2rib dup-host-mac-detection

{ no l2rib dup-host-mac-detection } | { l2rib dup-host-mac-detection <num-of-moves> <duration> }

Syntax Description

no

Negate a command or set its defaults

l2rib

Layer 2 routing information base

dup-host-mac-detection

Set Duplicate-Host-MAC-Detection parameters

num-of-moves

Number of host moves to be allowed

duration

Duplicate detection timeout in secs for host moves

Command Mode

  • /exec/configure

l2rib dup-host-mac-recovery

{ no l2rib dup-host-mac-recovery } | { l2rib dup-host-mac-recovery <timeout> <retry-count> }

Syntax Description

no

Negate a command or set its defaults

l2rib

Layer 2 routing information base

dup-host-mac-recovery

Set Duplicate-Host-MAC-Recovery (Unfreeze) parameters

timeout

Unfreeze timeout (secs)

retry-count

Unfreeze retry count

Command Mode

  • /exec/configure

label-allocation-mode per-vrf

[no] label-allocation-mode per-vrf

Syntax Description

no

(Optional) Negate a command or set its defaults

label-allocation-mode

Configure label allocation mode

per-vrf

per VRF label allocation mode

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

label allocate global

[no] label allocate global { all-routes | host-routes | prefix-list <pfx-list> }

Syntax Description

no

(Optional) Negate a command or set its defaults

label

LDP label configuration

allocate

Allocate local labels

global

Specify default VPN Routing/Forwarding instance

all-routes

Allocate local labels for all routes

host-routes

Allocate local labels for host routes only (default)

prefix-list

Specify a prefix-list for local label filtering

pfx-list

IP prefix-list for destination prefixes

Command Mode

  • /exec/configure/ldp

lacp graceful-convergence

lacp graceful-convergence | no lacp graceful-convergence

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

graceful-convergence

Configure port-channel lacp graceful convergence. Disable this only with lacp ports connected to Non-Nexus peer. Disabling this with Nexus peer can lead to port suspension

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp max-bundle

lacp max-bundle <max-bundle-number> | no lacp max-bundle [ <max-bundle-number> ]

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

max-bundle

Configure the port-channel max-bundle

max-bundle-number

Enter the max-bundle number

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp min-links

lacp min-links <min-links-number> | no lacp min-links [ <min-links-number> ]

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

min-links

Configure the port-channel min-links

min-links-number

Enter the min-link number

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description

no

(Optional) Negate a command or set its defaults

lacp

Set LACP parameters for the interface

mode

Enter the LACP mode

delay

Configure delayed lacp on the port-channel

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp mode delay

[no] lacp mode delay

Syntax Description

no

(Optional) Negate a command or set its defaults

lacp

Set LACP parameters for the interface

mode

Enter the LACP mode

delay

Configure delayed lacp on the port-channel

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp port-priority

lacp port-priority <port-pri> | no lacp port-priority

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

port-priority

Set LACP port priority

port-pri

Enter port priority

Command Mode

  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

lacp rate

[no] lacp rate

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

rate

Configure rate at which PDUs are sent by LACP

Command Mode

  • /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp rate

lacp rate <rate_type>

Syntax Description

lacp

Set LACP parameters for the interface

rate

Configure rate at which PDUs are sent by LACP

rate_type

Rate type

Command Mode

  • /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp suspend-individual

lacp suspend-individual | no lacp suspend-individual

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

suspend-individual

Configure lacp port-channel state. Disabling this will cause lacp to put the port to individual state and not suspend the port in case it does not get LACP BPDU from the peer ports in the port-channel

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp system-mac

lacp system-mac <mac-address> [ role <role> ] | no lacp system-mac

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

system-mac

Configure the MAC address to be used for the LACP Protocol exchanges

mac-address

MAC-address(FORMAT :xxxx.xxxx.xxxx)

role

(Optional) Configure the role for this Switch

role

(Optional) Role played by the Switch

Command Mode

  • /exec/configure

lacp system-priority

lacp system-priority <sys-pri> | no lacp system-priority

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

system-priority

Set LACP system priority

sys-pri

Enter System Priority

Command Mode

  • /exec/configure

lacp vpc-convergence

lacp vpc-convergence | no lacp vpc-convergence

Syntax Description

no

Negate a command or set its defaults

lacp

Set LACP parameters for the interface

vpc-convergence

Enable lacp convergence for vPC port channels.

Command Mode

  • /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

last

| last [ <lines> ]

Syntax Description

|

Pipe command output to filter

last

Display last lines

lines

(Optional) number of lines to print

Command Mode

  • /output

latency

{ [ no ] latency <lat> | no latency }

Syntax Description

latency

Provide the latency value for this POSTCARD queue_profile

lat

queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

  • /exec/configure/config-postcard-q-prof

latency

{ [ no ] latency <lat> | no latency }

Syntax Description

latency

Provide the latency value for this INT queue_profile

lat

queue_profile latency (nano seconds). Default is 2048 ns

Command Mode

  • /exec/configure/config-int-q-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description

latency

Provide the latency value for this POSTCARD flow-profile

quantization

Provide the latency value for this POSTCARD flow-profile

lat

flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any postcard in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28. Default is 11.

Command Mode

  • /exec/configure/config-postcard-flow-prof

latency quantization

{ [ no ] latency quantization <lat> | no latency quantization }

Syntax Description

latency

Provide the latency value for this INT flow-profile

quantization

Provide the latency value for this INT flow-profile

lat

flow-profile latency quantization. This value will be converted to a power of 2 (nanoseconds). For example, value of 11 will be converted to 2 power 11 which is 2048. This means that if the difference between ingress timestamp and egress timestamp is more than 2048 nanosec at any point in the path, one upstream report or local report will be generated per flow. The allowed values are in range 0-28 Default is 11.

Command Mode

  • /exec/configure/config-int-flow-prof

layer-2 multicast lookup mac

[no] layer-2 multicast lookup mac

Syntax Description

no

(Optional) Negate a command or set its defaults

layer-2

set layer2 multicast lkup mode

multicast

set layer2 multicast lkup mode

lookup

lkup type can be either mac or ip based

mac

set mac based multicast lkup mode

Command Mode

  • /exec/configure

layer-2 multicast lookup mac

[no] layer-2 multicast lookup mac

Syntax Description

no

(Optional) Negate a command or set its defaults

layer-2

set layer2 multicast lkup mode

multicast

set layer2 multicast lkup mode

lookup

lkup type can be either mac or ip based

mac

set mac based multicast lkup mode

Command Mode

  • /exec/configure/vlan-config /exec/configure/bdomain

layer2-switched flow monitor input

[no] layer2-switched flow monitor <monitorname> input

Syntax Description

layer2-switched

Configure L2 features

flow

NetFlow related commands

monitor

Apply a Flow Monitor to this interface

monitorname

Name of Flow Monitor

input

Apply Flow Monitor on input traffic

Command Mode

  • /exec/configure/if-switching

layer3 peer-router

layer3 peer-router | no layer3 peer-router

Syntax Description

no

Negate a command or set its defaults

layer3

Enable layer 3 functionality

peer-router

no change for TTL of packets destined to the peer

Command Mode

  • /exec/configure/vpc-domain

ldap-search-map

[no] ldap-search-map

Syntax Description

no

Negate a command or set its defaults

ldap-search-map

Set one of the configured search-map as active

Command Mode

  • /exec/configure/ldap

ldap-search-map

ldap-search-map <s0>

Syntax Description

ldap-search-map

Set one of the configured search-map as active

s0

Name of the search-map

Command Mode

  • /exec/configure/ldap

ldap-server deadtime

[no] ldap-server deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

deadtime

Global LDAP server deadtime period in seconds

i0

LDAP server deadtime period in minutes (default 0 mins -disabled)

Command Mode

  • /exec/configure

ldap-server host

[no] ldap-server host { <hostipname> } [ { enable-ssl | port <i1> [ timeout <i2> ] | rootDN <s0> [ password { 7 <s1> { { [ port1 <i3> [ timeout1 <i4> ] ] } | { [ timeout5 <i9> ] } } | <s2> { { [ port2 <i5> [ timeout2 <i6> ] ] } | { [ timeout4 <i8> ] } } } ] | timeout3 <i7> | referral-disable } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

host

LDAP server's DNS name or IP address

hostipname

IPV4/IPV6 address or DNS name

enable-ssl

(Optional) LDAP server enable ssl

port

(Optional) LDAP server's port (default: global config)

i1

(Optional) port number

timeout

(Optional) LDAP server timeout period in seconds

i2

(Optional) LDAP server timeout in seconds (default: global config)

rootDN

(Optional) LDAP server root DN

s0

(Optional) root DN

password

(Optional) LDAP server root password

7

(Optional) LDAP root password (encrypted)

s1

(Optional) password (encrypted)

port1

(Optional) LDAP server's port (default: global config)

i3

(Optional) port number

timeout1

(Optional) LDAP server timeout period in seconds

i4

(Optional) LDAP server timeout in seconds (default: global config)

s2

(Optional) password (clear text)

port2

(Optional) LDAP server's port (default: global config)

i5

(Optional) port number

timeout2

(Optional) LDAP server timeout period in seconds

i6

(Optional) LDAP server timeout in seconds (default: global config)

timeout3

(Optional) LDAP server timeout period in seconds

i7

(Optional) LDAP server timeout in seconds (default: global config)

timeout4

(Optional) LDAP server timeout period in seconds

i8

(Optional) LDAP server timeout in seconds (default: global config)

timeout5

(Optional) LDAP server timeout period in seconds

i9

(Optional) LDAP server timeout in seconds (default: global config)

referral-disable

(Optional) LDAP server disable referrals

Command Mode

  • /exec/configure

ldap-server host test rootDN

[no] ldap-server host { <hostipname> } test rootDN <r1> { { [ username <s0> { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] | [ idle-time <i1> ] } ] } | { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] } | { [ idle-time <i1> ] } }

Syntax Description

username

(Optional) <s0>

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

host

LDAP server's IP address

hostipname

IPV4/IPV6 address or DNS name

test

Parameters to send test packets

7

(Optional) LDAP test password (encrypted)

s0

(Optional) user name

password

(Optional) user password in test packets

s1

(Optional) test password

s2

(Optional) test password (encrypted)

rootDN

rootDN in test packets

r1

root DN

idle-time

(Optional) time interval for monitoring the server

i1

(Optional) time period in minutes

Command Mode

  • /exec/configure

ldap-server timeout

[no] ldap-server timeout <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap-server

Configure LDAP related parameters

timeout

Global LDAP server timeout period in seconds

i0

LDAP server timeout period in seconds (default 5 sec)

Command Mode

  • /exec/configure

ldap search-map

[no] ldap search-map <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

ldap

Configure information about ldap

search-map

Configure the search-map

s0

Search Map Name

Command Mode

  • /exec/configure

less

| less [ -d | -E ] +

Syntax Description

|

Pipe command output to filter

less

Filter for paging

-d

(Optional) dumb terminal

-E

(Optional) quit at end of file

Command Mode

  • /output

limit-resource module-type

{ limit-resource module-type <card-type> + } | { no limit-resource module-type }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

module-type

Controls which type of modules are allowed in this vdc

card-type

Allowed module types

Command Mode

  • /exec/configure/vdc

limit-resource monitor-session-erspan-dst minimum maximum equal-to-min

{ limit-resource monitor-session-erspan-dst minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-erspan-dst [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session-erspan-dst

Monitor erspan destination session

minimum

minimum monitor erspan-dst session to allocate

min-val

minimum monitor erspan-dst session value

maximum

maximum monitor erspan-dst session to allocate

max-val

maximum monitor erspan-dst session value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session-inband-src minimum maximum equal-to-min

{ limit-resource monitor-session-inband-src minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-inband-src [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session-inband-src

Monitor inband source

minimum

minimum monitor inband source to allocate

min-val

minimum monitor inband source value

maximum

maximum monitor inband source to allocate

max-val

maximum monitor inband source value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session minimum maximum equal-to-min

{ limit-resource monitor-session minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

limit-resource

Resource configuration

monitor-session

Monitor local/erspan-source session

minimum

minimum monitor local session to allocate

min-val

minimum monitor local session value

maximum

maximum monitor local session to allocate

max-val

maximum monitor local session value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource port-channel minimum maximum

limit-resource port-channel minimum <min-val> maximum { <max-val> | equal-to-min } | no limit-resource port-channel [ minimum <min-val> maximum { <max-val> | equal-to-min } ]

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

port-channel

set port-channel limits

minimum

minimum port-channels to allocate

min-val

maximum

maximum port-channels to allocate

max-val

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource vlan minimum maximum equal-to-min

{ limit-resource vlan minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource vlan [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

vlan

set VLAN limits

minimum

minimum VLANs to allocate

min-val

minimum VLANs value

maximum

maximum VLANs to allocate

max-val

maximum VLANs value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit-resource vrf minimum maximum equal-to-min

{ limit-resource vrf minimum <number1> maximum { <number2> | equal-to-min } } | { no limit-resource vrf [ minimum <number1> maximum { <number2> | equal-to-min } ] }

Syntax Description

no

Negate a command or set its defaults

limit-resource

Resource configuration

vrf

set vrf resource limits

minimum

minimum vrf resources to allocate

number1

minimum vrf resource value

maximum

maximum vrf resources to allocate

number2

maximum vrf resource value

equal-to-min

set maximum value equal to min

Command Mode

  • /exec/configure/vdc-template /exec/configure/vdc

limit address-count

[no] limit address-count <addr_count>

Syntax Description

no

(Optional) Negate a command or set its defaults

addr_count

maximum value

Command Mode

  • /exec/configure/config-snoop-policy

line console

[no] line console

Syntax Description

no

(Optional) Negate a command or set its defaults

line

Configure a terminal line

console

Primary terminal line

Command Mode

  • /exec/configure

line console

[no] line console

Syntax Description

no

(Optional) Negate a command or set its defaults

line

Configure a terminal line

console

Primary terminal line

Command Mode

  • /exec/configure

line vty

line vty

Syntax Description

line

Configure a terminal line

vty

Virtual terminal line

Command Mode

  • /exec/configure

link-management timers bandwidth

[no] link-management timers { bandwidth-hold | periodic-flooding } | link-management timers { bandwidth-hold <bw_seconds> | periodic-flooding <flood_seconds> }

Syntax Description

no

Negate a command or set its defaults

link-management

Link Management configuration

timers

Link Management timers configuration

bandwidth-hold

Link Management bandwidth hold timer

bw_seconds

seconds

periodic-flooding

Link Management periodic flooding interval

flood_seconds

seconds [0 to disable, minimum set to 30]

Command Mode

  • /exec/configure/te

link-state-trap

[no] link-state-trap

Syntax Description

no

(Optional) Negate a command or set its defaults

link-state-trap

Enable/disable link state change traps

Command Mode

  • /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-fcip /exec/configure/if-iscsi

link debounce

link debounce { [ link-up [ time <time_val_link_up> ] ] | [ time <time_val> ] } | no link debounce [ link-up ]

Syntax Description

no

Negate a command or set its defaults

link

Configure link

debounce

Configure link debounce timer

link-up

(Optional) Timer for the link-up event

time

(Optional) Link debounce time

time_val

(Optional) Timer value (in milliseconds)

time_val_link_up

(Optional) Timer value (in milliseconds)

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

link rxlos

link rxlos [ algo <algo_val> ] | no link rxlos [ algo <algo_val> ]

Syntax Description

no

Negate a command or set its defaults

link

Configure link

rxlos

Configure link rxlos algo

algo

(Optional) Link rxlos algo control

algo_val

(Optional) rxlos control options

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-sub

list

list

Syntax Description

list

Re-list all of the attribute list entries

Command Mode

  • /exec/configure/te/lsp-attr

list

list [ <index> ]

Syntax Description

list

Re-list all or part of the explicit path entries

index

(Optional) List starting at entry index number

Command Mode

  • /exec/configure/te/expl-path

listobject-boolean not

listobject-boolean <object-id> not

Syntax Description

listobject-boolean

Configure Object as member of tracking list

object-id

Tracked object

not

Negate Up status

Command Mode

  • /exec/configure/tr-list-bool

listobject-weight weight threshold-weight

listobject-weight { <object-id> weight <weight-val> } | threshold-weight { weight-thresh { weightup <up-weight> [ weightdown <down-weight> ] | weightdown <down-weight> [ weightup <up-weight> ] } } | no threshold-weight weight-thresh

Syntax Description

no

Negate a command or set its defaults

listobject-weight

Configure Object as member of tracking list

object-id

Tracked Object

weight

Assign a weight to object

weight-val

Assign a weight to object

threshold-weight

Threshold parameters

weight-thresh

Weight threshold

weightup

Up threshold

up-weight

Up threshold weight

weightdown

(Optional) Down threshold

down-weight

(Optional) Down threshold weight

Command Mode

  • /exec/configure/tr-list-thrw

listobject

[no] listobject <object-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

listobject

Configure Object as member of tracking list

object-id

Tracked Object

Command Mode

  • /exec/configure/tr-list-thrw /exec/configure/tr-list-thrp /exec/configure/tr-list-bool

lldp

[no] lldp { holdtime <i0> | reinit <i1> | timer <i2> | portid-subtype <i3> | tlv-select { management-address | port-description | port-vlan | power-management | system-capabilities | system-description | system-name | dcbxp } }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure global LLDP parameters

holdtime

Specify the holdtime (in sec) to be sent in packets

i0

holdtime in sec

reinit

Delay (in sec) for LLDP initialisation on any interface

i1

reinit in sec

timer

Specify the rate at which LLDP packets are sent (in sec)

i2

rate of packets in sec

portid-subtype

config portid subtype for LLDP TLV and SNMP MIBs

i3

0: long interface name (default), 1: short interface name

tlv-select

Selection of LLDP to send

management-address

Management Address TLV

port-description

Port Description TLV

port-vlan

Port Vlan ID TLV

power-management

IEEE 802.3 DTE Power via MDI TLV

system-capabilities

System Capabilities TLV

system-description

System Description TLV

system-name

System Name TLV

dcbxp

DCBXP TLVs

Command Mode

  • /exec/configure

lldp dcbx version auto

lldp dcbx version auto

Syntax Description

lldp

Configure LLDP parameters

dcbx

Configure DCBX parameters

version

Change the DCBX protocol version

auto

Auto-detect the DCBX version

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp dcbx version cee

[no] lldp dcbx version { cee | ieee }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure LLDP parameters

dcbx

Configure DCBX parameters

version

Change the DCBX protocol version

cee

The CEE version of DCBX

ieee

The IEEE 802.1 version of DCBX

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp receive

[no] lldp receive

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

receive

Enable LLDP reception on interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-select management-address v4

[no] lldp tlv-select management-address { v4 | v6 }

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure global LLDP parameters

tlv-select

Selection of LLDP to send

management-address

Management Address TLV

v4

Management Address TLV v4

v6

Management Address TLV v6

Command Mode

  • /exec/configure

lldp tlv-set management-address

[no] lldp tlv-set management-address <ip-addr>

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

management-address

Management address to be sent in management-tlv of LLDPDU.

ip-addr

IP address in dotted decimal format i.i.i.i

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set management-address ipv6

[no] lldp tlv-set management-address <ipv6-addr> ipv6

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

management-address

Management address to be sent in management-tlv of LLDPDU.

ipv6

IPV6

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set vlan

[no] lldp tlv-set vlan [ <vlan-id> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

tlv-set

LLDP TLV configuration for interface

vlan

VLAN-id whose SVI IP address should be used as management adrress in management-tlv of LLDPDU. Default is native VLAN.

vlan-id

(Optional) vlan-id within range of 1-4094

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp transmit

[no] lldp transmit

Syntax Description

no

(Optional) Negate a command or set its defaults

lldp

Configure Interface LLDP parameters

transmit

Enable LLDP transmission on interface

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

load-balance

[no] load-balance { { method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | { buckets <num> } | { mask-position <mask> } } + } [ least-bit ]

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

ITD Loadbalance

method

ITD Loadbalance method

src

Source based parameters

dst

Destination based parameters

ip

IP

ip-l4port

IP and L4 port

src-protocol

Protocol

range

Match only packets in the range of port numbers

src-x

src-y

ip-dst

IP

dst-protocol

Protocol

dst-x

dst-y

buckets

Used to create the buckets for traffic distribution, and it should be in powers of 2

num

Loadbalance bucket number

mask-position

Loadbalance mask position

mask

Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6

least-bit

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/itd

load-balance

[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

Loadbalance

method

(Optional) Loadbalance method

src

(Optional) Source based parameters

dst

(Optional) Destination based parameters

ip

(Optional) IP

ip-l4port

(Optional) IP and L4 port

src-protocol

(Optional) Protocol

range

(Optional) Match only packets in the range of port numbers

src-x

(Optional)

src-y

(Optional)

ip-dst

(Optional) IP

dst-protocol

(Optional) Protocol

dst-x

(Optional)

dst-y

(Optional)

buckets

(Optional) Used to create the buckets for traffic distribution, and it should be in powers of 2

num

(Optional) Loadbalance bucket number

mask-position

(Optional) Loadbalance mask position

mask

(Optional) Loadbalance mask position number range 0-31 for IPv4 and 0-127 for IPv6

Command Mode

  • /exec/configure/smartc

load-balance

[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }

Syntax Description

no

(Optional) Negate a command or set its defaults

load-balance

PLB Loadbalance options

method

(Optional) Loadbalance method

src

(Optional) Source based parameters

dst

(Optional) Destination based parameters

ip

(Optional) IP

ip-l4port

(Optional) IP and L4 port

src-protocol

(Optional) Protocol

range

(Optional) Match only packets in the range of port numbers

src-x

(Optional)

src-y

(Optional)

ip-dst

(Optional) IP

dst-protocol

(Optional) Protocol

dst-x

(Optional)

dst-y

(Optional)

buckets

(Optional) Used to create the buckets for traffic distribution, and it should be in powers of 2

num

(Optional) Loadbalance bucket number

mask-position

(Optional) Loadbalance mask position

mask

(Optional) Loadbalance mask position number range 0-23 for IPv4 and 0-127 for IPv6

Command Mode

  • /exec/configure/plb

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-vlan-common

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

counter

Specify counter for this load interval

counter_val

Specify counter for this load interval

interval

Load interval delay in seconds

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description

no

Negate a command or set its defaults

load-interval

Specify interval for load calculation for an interface

counter

Specify counter for this load interval

interval

Load interval delay in seconds

counter_val

Specify counter for this load interval

interval1

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

  • /exec/configure/if-vlan-common

load

load <uri0>

Syntax Description

load

Load system image

uri0

Enter image URI

Command Mode

  • /exec

load

load <uri0> [ <s0> ]

Syntax Description

load

Load system image

uri0

Enter image URI

s0

(Optional) Options

Command Mode

  • /exec

load

load <uri0> [ <s0> ]

Syntax Description

load

Load system image

uri0

Enter image URI

s0

(Optional) Options

Command Mode

  • /exec

local-as

local-as <asn> | no local-as [ <asn> ]

Syntax Description

no

Negate a command or set its defaults

local-as

Specify the local-as for this vrf

asn

AS number

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf

local-as

{ local-as <asn> [ no-prepend [ replace-as [ dual-as ] ] ] } | { { no | default } local-as [ <asn> ] }

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

local-as

Specify the local-as number for the eBGP neighbor

asn

Autonomous System Number

no-prepend

(Optional) Do not prepend the local-as number to updates from the eBGP neighbor

replace-as

(Optional) Prepend only the local-as number to updates to eBGP neighbor

dual-as

(Optional) Connect using either the local-as number or the real as

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <prefix> <mask> | <prefix-mask> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

local-label

Configure local label assignment and forwarding

static-inlabel

Label Value

prefix

For a given prefix

prefix

Destination prefix

mask

Destination prefix mask

prefix-mask

Destination prefix/mask

Command Mode

  • /exec/configure/mpls_static/ipv4

local-label prefix

[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <ipv6-prefix-mask> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

vrf

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

local-label

Configure local label assignment and forwarding

static-inlabel

Label Value

prefix

For a given prefix

Command Mode

  • /exec/configure/mpls_static/ipv6

locator-led

[no] locator-led { chassis | module <module> | fan <fan_num> }

Syntax Description

no

(Optional) Negate a command or set its defaults

locator-led

blink locator led on device

chassis

blink chassis led

module

blink module led

module

please enter the module number

fan

blink Fan led

fan_num

fan number

Command Mode

  • /exec

lockdown

[no] lockdown

Syntax Description

no

(Optional) Negate a command or set its defaults

lockdown

Lockdown the LSP--disable reoptimization

Command Mode

  • /exec/configure/te/lsp-attr

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

detail

(Optional) Notify all state changes

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

detail

(Optional) Notify all state changes

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-adjacency-changes

Log changes in adjacency state

Command Mode

  • /exec/configure/l2mp-isis/l2mp-isis-vrf-common

log-neighbor-changes

[no] log-neighbor-changes

Syntax Description

no

(Optional) Negate a command or set its defaults

log-neighbor-changes

Log a message for neighbor up/down event

Command Mode

  • /exec/configure/router-bgp/vrf-cmds

log-neighbor-changes

[ no | default ] log-neighbor-changes [ disable ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

log-neighbor-changes

Log message for neighbor up/down event

disable

(Optional) Disable logging of neighbor up/down event

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

log-neighbor-warnings

{ { [ eigrp ] log-neighbor-warnings [ <interval> ] } | { no [ eigrp ] log-neighbor-warnings [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

eigrp

THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

log-neighbor-warnings

Enable/Disable IP-EIGRP neighbor warnings

interval

(Optional) Neighbor warning interval in seconds

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

logging

[no] logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel { lsp-selection | path change } } | logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel { lsp-selection | path change } }

Syntax Description

no

Negate a command or set its defaults

logging

Trap logging configuration

lsp

LSP-specific traps logging configuration

path-errors

Log LSP Path Error traps

preemption

Log LSP Preemption traps

reservation-errors

Log LSP Reservation Error traps

setups

Log LSP Establishment Traps

teardowns

Log LSP Teardown Traps

tunnel

Tunnel-specific traps logging configuration

lsp-selection

Log Tunnel LSP Selection traps

path

Log Tunnel Path-related traps

change

Log Tunnel Path change traps

Command Mode

  • /exec/configure/te

logging

[no] logging { neighbor-changes |

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Enable LDP logging

neighbor-changes

Log LDP neighbor state changes

Command Mode

  • /exec/configure/ldp

logging abort

logging abort

Syntax Description

logging

Modify message logging facilities

abort

Flushes cached data without committing and releases the lock

Command Mode

  • /exec/configure

logging console

[no] logging console [ <i0> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

console

Set console logging

i0

(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging distribute

[no] logging distribute

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

distribute

Enables/disables fabric distribution using cfs.

Command Mode

  • /exec/configure

logging event link enable

[no] logging event { link-status | trunk-status } { enable | default }

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

link-status

UPDOWN and CHANGE messages

trunk-status

TRUNK status messages

enable

To enable logging overriding port level configuration

default

default logging configuration used by interfaces not explicitly configured

Command Mode

  • /exec/configure

logging event port link-status

logging event port link-status [ default ] | no logging event port link-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

default

(Optional) Use the global default value

Command Mode

  • /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-gig-ether-sub /exec/configure/if-loopback /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status

logging event port link-status

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port link-status

[no] logging event port link-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port link-status default

logging event port link-status default

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

link-status

UPDOWN and CHANGE messages

default

Use the global default value

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

[no] logging event port trunk-status

Syntax Description

no

Negate a command or set its defaults

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

logging event port trunk-status

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status default

logging event port trunk-status default

Syntax Description

logging

Configure logging for interface

event

Interface events

port

Port level events

trunk-status

TRUNK status messages

default

Use the global default value

Command Mode

  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging flow-mod

[no] logging flow-mod

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Enable logging

flow-mod

Enable logging for flow-modify

Command Mode

  • /exec/configure/openflow/switch/sub-switch

logging flow-mod

[no] logging flow-mod

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Enable logging

flow-mod

Enable logging for flow-modify

Command Mode

  • /exec/configure/openflow/switch

logging ip access-list cache

[no] logging ip access-list cache { { interval <seconds> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

ip

IP configuration

access-list

Access-list

cache

logging

interval

Log-update interval (in sec)

seconds

Log-update interval in seconds

Command Mode

  • /exec/configure

logging ip access-list cache entries

[no] logging ip access-list cache { { entries <num_entries> } | { threshold <num_packets> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

ip

IP configuration

access-list

Access-list

cache

logging

entries

Maximum number of log entries cached in software

num_entries

Number of entries

threshold

Log-update threshold

num_packets

Log-update threshold (number of hits)

Command Mode

  • /exec/configure

logging ip access-list detailed

[no] logging ip access-list detailed

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Enable detailed logging

ip

configured IP

access-list

Access-list

detailed

Detailed ACL information

Command Mode

  • /exec/configure

logging ip access-list include sgt

[no] logging ip access-list include sgt

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

ip

IP configuration

access-list

Access-list

include

Include additional fields in syslogs

sgt

Include source group tag info in syslogs

Command Mode

  • /exec/configure

logging level

[no] logging level { { routing ipv6 multicast } | m6rib } <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

routing

Configure routing information

ipv6

Configure IPv6 features

multicast

Set syslog filter level for MRIB

m6rib

Set syslog filter level for MRIB

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

{ logging level { auth <i1> | authpriv <i2> | cron <i3> | daemon <i4> | ftp <i5> | kernel <i6> | local0 <i7> | local1 <i8> | local2 <i9> | local3 <i10> | local4 <i11> | local5 <i12> | local6 <i13> | local7 <i14> | lpr <i15> | mail <i16> | news <i17> | syslog <i18> | user <i19> | uucp <i20> } | no logging level { auth [ <i1> ] | authpriv [ <i2> ] | cron [ <i3> ] | daemon [ <i4> ] | ftp [ <i5> ] | kernel [ <i6> ] | local0 [ <i7> ] | local1 [ <i8> ] | local2 [ <i9> ] | local3 [ <i10> ] | local4 [ <i11> ] | local5 [ <i12> ] | local6 [ <i13> ] | local7 [ <i14> ] | lpr [ <i15> ] | mail [ <i16> ] | news [ <i17> ] | syslog [ <i18> ] | user [ <i19> ] | uucp [ <i20> ] } }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

auth

Set level for Authorization System

i1

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

authpriv

Set level for Authorization (Private) system

i2

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

cron

Set level for Cron/at facility

i3

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

daemon

Set level for System daemons

i4

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

ftp

Set level for File Transfer System

i5

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

kernel

Set level for kernel

i6

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local0

Set level for Local use daemons

i7

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local1

Set level for Local use daemons

i8

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local2

Set level for Local use daemons

i9

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local3

Set level for Local use daemons

i10

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local4

Set level for Local use daemons

i11

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local5

Set level for Local use daemons

i12

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local6

Set level for Local use daemons

i13

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

local7

Set level for Local use daemons

i14

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

lpr

Set level for Line Printer System

i15

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

mail

Set level for Mail system

i16

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

news

Set level for USENET news

i17

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

syslog

Set level for Internal Syslog Messages

i18

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

user

Set level for User Process

i19

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

uucp

Set level for Unix-to-Unix copy system

i20

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

[no] logging level { { routing [ ip | ipv4 ] multicast } | mrib } <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

routing

Configure routing information

ip

(Optional) Configure IP features

ipv4

(Optional) Configure IP features

multicast

Set syslog filter level for MRIB

mrib

Set syslog filter level for MRIB

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level

[no] logging level { xml server | xmlma } <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

xml

xml agent

server

xml agent server

xmlma

xml master agent. Same as combination of keywords xml server

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level aaa

logging level aaa <i0> | no logging level aaa [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

aaa

Set level for aaa syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level acllog

logging level acllog <i0> | no logging level acllog [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

acllog

Set level for acllog syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level aclmgr

[no] logging level aclmgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

aclmgr

Set level for aclmgr syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level adbm

[no] logging level adbm <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

adbm

Set level for adbm syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level adjmgr

[no] logging level adjmgr <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

adjmgr

Set syslog filter level for Adjacency Manager

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level all

{ logging level { all <i0> } | no logging level { all [ <i0> ] } }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

all

Set level for all facilities

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level amt

[no] logging level amt <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

amt

Set syslog filter level for AMT

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level arp

{ logging level arp <level> } | { no logging level arp [ <level> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

arp

Set syslog filter level for ARP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ascii-cfg

[no] logging level ascii-cfg <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ascii-cfg

Set logging level for ascii-cfg

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level assoc_mgr

[no] logging level assoc_mgr <i0> | no logging level assoc_mgr [ <i0> ]

Syntax Description

no

(Optional) Negate a command or set its default

logging

Show logging configuration and contents of logfile

level

Show facility logging configuration

assoc_mgr

Show Association Manager Logging Configuration

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level backup

[no] logging level { backup | flexlink } <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

backup

Set level for Switchport Backup syslog messages

flexlink

Set level for Switchport Backup syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bfd

[no] logging level bfd <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bfd

Set level for bfd syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bgp

[no] logging level bgp <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bgp

Set syslog filter level for BGP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bloggerd

[no] logging level bloggerd <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bloggerd

Set level for BloggerD syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level bootvar

[no] logging level bootvar <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

bootvar

Set level for bootvar

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level callhome

logging level callhome <i0> | no logging level callhome [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

callhome

Callhome syslog level

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level capability

[no] logging level capability <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

capability

Set syslog level for mig utils daemon

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level catena

[no] logging level catena <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

catena

Set level for catena syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cdp

logging level cdp <i0> | no logging level cdp [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

cdp

Set level for CDP syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cfs

[no] logging level cfs <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level clis

[no] logging level clis <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

clis

Set syslog filter level for CLIS

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level clk_mgr

[no] logging level clk_mgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

clk_mgr

Set level for clock manager syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level confcheck

{ logging level confcheck <i0> | no logging level confcheck [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level copp

logging level copp <i0> | no logging level copp [ <i0> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

copp

Set level for copp syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level core

{ logging level core <i0> | no logging level core [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

core

core daemon syslog level

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level cts

[no] logging level cts <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

cts

Set level for cts syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dhclient

[no] logging level dhclient <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dhclient

Set level for dhcp client syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dhcp_snoop

logging level dhcp_snoop <level> | no logging level dhcp_snoop [ <level> ]

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dhcp_snoop

Set level for dhcp snoop syslog messages

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level diagclient

[no] logging level diagclient <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

diagclient

Set level for GOLD DiagClient syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level diagmgr

[no] logging level diagmgr <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

diagmgr

Set level for GOLD DiagMgr syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level dot1x

[no] logging level dot1x <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

dot1x

Set level for dot1x syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level ecp

[no] logging level ecp <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

ecp

Set syslog filter level for ECP

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level eigrp

[no] logging level eigrp [ <eigrp-ptag> ] <level>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

eigrp

Set syslog filter level for EIGRP

eigrp-ptag

(Optional) Process tag

level

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level eltm

logging level eltm <i0> | no logging level eltm

Syntax Description

no

Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

eltm

Set level for eltm syslog messages

i0

0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debug

Command Mode

  • /exec/configure

logging level epp

[no] logging level epp <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

logging

Modify message logging facilities

level

Facility parameter for syslog messages

epp

Set level for EPP syslog messages

i0