A Show Commands
show aaa accounting
show aaa authentication
show aaa authentication login
show aaa authentication login ascii-authentication
show aaa authentication login error-enable
show aaa authentication login invalid-username-log
show aaa authorization
show aaa bypass-user
show aaa client radius statistics
show aaa groups
show aaa local user blocked
show aaa server radius statistics
show aaa user default-role
show access-list
show access-list database
show access-lists
show access-lists
show accounting log
show accounting log all
show accounting log last-index
show accounting log nvram
show accounting log nvram last-index
show accounting log nvram start-seqnum
show accounting log start-seqnum
show acl status
show amt process
show amt vrf all
show archive log config
show arp access-lists

A Show Commands

show aaa accounting

show aaa accounting [ __readonly__ [ TABLE_acctMethods <service> <methods> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
accounting	Show accounting configuration
__readonly__	(Optional)
TABLE_acctMethods	(Optional)
service	(Optional) service type
methods	(Optional) Accounting methods configured for the application

Command Mode

/exec

show aaa authentication

show aaa authentication [ __readonly__ [ TABLE_AuthenMethods <service> <method> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authentication	Show authentication configuration
__readonly__	(Optional)
TABLE_AuthenMethods	(Optional)
service	(Optional) Service for which authentication is needed
method	(Optional) Authentication method used for the service

Command Mode

/exec

show aaa authentication login

show aaa authentication login { mschap | mschapv2 | chap } [ __readonly__ [ <mschap_status> ] [ <mschapv2_status> ] [ <chap_status> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authentication	Show authentication configuration
login	Show authentication login error message configuration
mschap	Show authentication login MSCHAP enable configuration
mschapv2	Show authentication login MSCHAP V2 enable configuration
chap	Show authentication login CHAP enable configuration
__readonly__	(Optional)
mschap_status	(Optional) mschap enabled or disabled
mschapv2_status	(Optional) mschapv2 enabled or disabled
chap_status	(Optional) chap enabled or disabled

Command Mode

/exec

show aaa authentication login ascii-authentication

show aaa authentication login ascii-authentication [ __readonly__ { <ascii_authen_status> } ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authentication	Show authentication configuration
login	Show authentication login message configuration
ascii-authentication	Show ascii-authentication configuration
__readonly__	(Optional)
ascii_authen_status	(Optional) ascii authentication status

Command Mode

/exec

show aaa authentication login error-enable

show aaa authentication login error-enable [ __readonly__ [ <status> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authentication	Show authentication configuration
login	Show authentication login error message configuration
error-enable	Show authentication login error message enable configuration
__readonly__	(Optional)
status	(Optional) login error-enable enabled or disabled

Command Mode

/exec

show aaa authentication login invalid-username-log

show aaa authentication login invalid-username-log [ __readonly__ [ <status> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authentication	Show authentication configuration
login	Show authentication login message configuration
invalid-username-log	Show invalid username log configuration
__readonly__	(Optional)
status	(Optional) login invalid-username-log enabled or disabled

Command Mode

/exec

show aaa authorization

show aaa authorization [ all ] [ __readonly__ [ <pki_ssh_cert_author> <pki_ssh_pubkey_author> ] [ TABLE_cmd_methods <appl_subtype> <cmd_type> <methods> ] [ TABLE_app_methods <appl> <methods> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
authorization	Show authorization configuration
all	(Optional) Show all(include defaults configurations) authorization info
__readonly__	(Optional)
pki_ssh_cert_author	(Optional)
pki_ssh_pubkey_author	(Optional)
TABLE_cmd_methods	(Optional) table containing command authorization methods
appl_subtype	(Optional)
cmd_type	(Optional)
methods	(Optional)
TABLE_app_methods	(Optional) table containing application authorization methods
appl	(Optional)
methods	(Optional)

Command Mode

/exec

show aaa bypass-user

show aaa bypass-user [ <s0> ] [ __readonly__ [ <num_bypass_users> ] [ TABLE_bypassUsers <username> <account> <author> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
bypass-user	Show bypass user information
s0	(Optional) Enter the username
__readonly__	(Optional)
num_bypass_users	(Optional) Number of bypass users configured
TABLE_bypassUsers	(Optional)
username	(Optional) Username
account	(Optional) Accounting Bypass
author	(Optional) Authorization bypass

Command Mode

/exec

show aaa client radius statistics

show aaa client radius statistics <host0> [ __readonly__ TABLE_allstat [ <auth_client> ] TABLE_allcoastat [ <requests> ] [ <transactions> ] [ <retransmissions> ] [ <active_trans> ] [ <ack_responses> ] [ <nak_responses> ] [ <invalid_req> ] [ <errors> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
client	Show AAA client info
radius	show radius dynamic authorization client info
statistics	show radius dynamic authorization client statistics
host0	IPV4/IPV6 address or DNS name of RADIUS client
__readonly__	(Optional)
TABLE_allstat	(Optional)
TABLE_allcoastat	(Optional)
auth_client	(Optional) Authentication Client Port details
requests	(Optional) COA Request Sent count
transactions	(Optional) COA transactions count
retransmissions	(Optional) COA retransmission count
active_trans	(Optional) COA active transactions count
ack_responses	(Optional) COA acknowledgement responses count
nak_responses	(Optional) COA nak responses count
invalid_req	(Optional) Invalid requests count
errors	(Optional) COA Error count

Command Mode

/exec

show aaa groups

show aaa groups [ __readonly__ { TABLE_groups <group> } ]

Syntax Description


show	Show running system information
aaa	Show aaa information
groups	Show configured groups
__readonly__	(Optional)
TABLE_groups	(Optional) Table showing aaa groups
group	(Optional) Name of the group

Command Mode

/exec

show aaa local user blocked

show aaa local user blocked [ __readonly__ { TABLE_sessions <u_name> <u_state> } ]

Syntax Description


show	Show running system information
aaa	Configure aaa functions
local	Local username
user	Local system user
blocked	Display Blocked users
__readonly__	(Optional)
TABLE_sessions	(Optional) aaa local users blocked table
u_name	(Optional) Name of the user
u_state	(Optional) State of the user

Command Mode

/exec

show aaa server radius statistics

show aaa server radius statistics [ __readonly__ TABLE_allstat [ <auth_ser> ] [ <coa_sessions> ] TABLE_alldot1xstat [ <request_sent> ] [ <resp_received> ] [ <resp_timeout> ] [ <errors> ] ]

Syntax Description


show	Show running system information
aaa	Show aaa information
server	show Local AAA server info
radius	show local radius server info
statistics	show local radius server statistics
__readonly__	(Optional)
TABLE_allstat	(Optional)
TABLE_alldot1xstat	(Optional)
auth_ser	(Optional) Authentication Server Port details
coa_sessions	(Optional) Active COA session numbers
request_sent	(Optional) DOT1X Request Sent Count
resp_received	(Optional) DOT1X Response received Count
resp_timeout	(Optional) DOT1X Response Timeout Value
errors	(Optional) DOT1X Error count

Command Mode

/exec

show aaa user default-role

show aaa user default-role [ __readonly__ { default_role_status <udr_status> } ]

Syntax Description


show	Show running system information
aaa	Show aaa information
user	Remotely authenticated user
default-role	Default role assigned by aaa-admin for remote authentication
__readonly__	(Optional)
default_role_status	(Optional) user default role status
udr_status	(Optional) Status of user default role

Command Mode

/exec

show access-list

show { system internal | hardware } access-list { summary | [ vdc <vdc_id> ] { [ interface <if_name> | vlan <vlan_id> | inband table <table> ] [ { input | output } { config | { { entries | merge } [ detail ] } | statistics | l4ops | redirect | sampler } ] } } [ module <module> ] [ __readonly__ <type> <feature> <plcy_id> <src_ip> <src_mask> <dst_ip> <dst_mask> <proto> <l4ops> <action> <mac> <cos> <vlan> <l2_proto> <ethertype> [ TABLE_vdc <vdc-no> <vdc-type> <dir> <policy-type> <policy-id> <policy-name> ] [ TABLE_instance <inst> [ TABLE_tcam_resource_usage <tcam-no> <lbl> <hw-lbl-id> [ <bank> ] [ TABLE_bank <bank-no> [ TABLE_class <class-type> [ TABLE_policies <policy> ] <netflow-profile> <netflow-deny-profile> [ <tcam-entries> ] [ TABLE_tcam_entry <tcam-index> <tcam-rule> <tcam-stats> ] ] ] ] <l4-protocol-cam-entries> <mac-etype-proto-cam-entries> <lous> <tcp-flags-table-entries> <adjacency-entries> ] ]

Syntax Description


show	Show running system information
system	System-related show commands
internal	Commands for internal use
hardware	Show hardware information
access-list	Access Control List
summary	summary
vdc	(Optional) vdc id
vdc_id	(Optional) vdc_id
interface	(Optional) interface name
if_name	(Optional) display access list for the interface
vlan	(Optional) vlan_id
vlan_id	(Optional) vlan_id
inband	(Optional) inband interface
table	(Optional) vrf table number
table	(Optional) vrf table number
input	(Optional) input/ingress policies
output	(Optional) output/egress policies
config	(Optional) parsed policy software database
entries	(Optional) tcam entries
statistics	(Optional) aggregate statistics
l4ops	(Optional) l4 operations information
redirect	(Optional) redirect resource information
sampler	(Optional) with sampler details
merge	(Optional) tcam entries merge information
detail	(Optional) detailed information
module	(Optional) Slot/module
module	(Optional) Slot/module number
__readonly__	(Optional)
type	(Optional) policy type eg: ACL, QOS
feature	(Optional) feature type eg: RACL, VACL
plcy_id	(Optional) policy id
src_ip	(Optional) src ipv4 address
src_mask	(Optional) src mask
dst_ip	(Optional) dst ipv4 address
dst_mask	(Optional) dst mask
proto	(Optional) protocol eg: TCP, UDP ...
l4ops	(Optional) layer 4 operations
action	(Optional) action
mac	(Optional) mac address
cos	(Optional) acos value
vlan	(Optional) vlan id
l2_proto	(Optional) L2 protocol
ethertype	(Optional) ethertype
TABLE_vdc	(Optional) show for vdc
vdc-no	(Optional) vdc number
vdc-type	(Optional) VDC type-COPP etc
dir	(Optional) Policy Direction
policy-type	(Optional) Policy type
policy-id	(Optional) Policy id
policy-name	(Optional) Policy name
TABLE_instance	(Optional) show for an instance
inst	(Optional) instance number
TABLE_tcam_resource_usage	(Optional) TCAM resource usage
tcam-no	(Optional) tcam number
TABLE_bank	(Optional) table bank
bank-no	(Optional) bank number
lbl	(Optional) lbl name
hw-lbl-id	(Optional) hw lbl id
bank	(Optional) bank number
TABLE_class	(Optional) table class
class-type	(Optional) Class type
TABLE_policies	(Optional) policy table
policy	(Optional) Policy name
netflow-profile	(Optional) Netflow Profile
netflow-deny-profile	(Optional) Netflow Deny Profile
TABLE_tcam_entry	(Optional) table tcam entries
tcam-index	(Optional) Index of tcam entry
tcam-rule	(Optional) tcam rule
tcam-stats	(Optional) stats of tcam rule
tcam-entries	(Optional) No. of TCAM entries
l4-protocol-cam-entries	(Optional) L4 protocol cam entries
mac-etype-proto-cam-entries	(Optional) No. of mac etype/proto cam entries
lous	(Optional) No. of LOU's
tcp-flags-table-entries	(Optional) No. of CP flags table entries
adjacency-entries	(Optional) No. of adjacency entries

Command Mode

/exec

show access-list database

show { system internal | hardware } access-list [ vdc <vdc_id> ] database { interface | vlan | policy | process } [ module <module> ] [ __readonly__ <if_idx> <vlan> <plcy_id> <process_info> ]

Syntax Description


show	Show running system information
system	System-related show commands
internal	Commands for internal use
hardware	Show hardware information
access-list	Access Control List
vdc	(Optional) vdc id
vdc_id	(Optional) vdc_id
database	Show memory database
interface	display interfaces/vlans in a vdc with policies
policy	display policies in a vdc
vlan	display vlans in a vdc
process	display process database in a vdc
module	(Optional) Slot/module
module	(Optional) Slot/module number
__readonly__	(Optional)
if_idx	(Optional) interface
vlan	(Optional) vlan
plcy_id	(Optional) policy id
process_info	(Optional) process information

Command Mode

/exec

show access-lists

show <mpls_acl> access-lists [ <mpls_name> ] [ __readonly__ TABLE_mpls <mpls_name> [ <statistics> ] [ TABLE_seqno <seqno> { <permitdeny> <mpls> [ <mpls_option> ] { <label1_any> | { <label1> [ mask <label1_mask> ] } } [ <label2_any> | { <label2> [ mask <label2_mask> ] } ] [ <label3_any> | { <label3> [ mask <label3_mask> ] } ] [ <label4_any> | { <label4> [ mask <label4_mask> ] } ] <mplsaction> <mplsactionid> } | <remark> ] ]

Syntax Description


show	Show running system information
mpls_acl	mpls acl value
access-lists	List access lists
mpls_name	(Optional) List name
__readonly__	(Optional)
mpls_name	(Optional) Name of the MPLS ACL
seqno	(Optional) Sequence number
permitdeny	(Optional) Permit/deny
mplsaction	(Optional) mpls ACL Action
mplsactionid	(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63> set-erspan-gre-proto: <1-65535>
statistics	(Optional) STATISTICS
mask	(Optional) mask
label1	(Optional) mpls label one
label2	(Optional) mpls label two
label3	(Optional) mpls label three
label4	(Optional) mpls label three
label1_mask	(Optional) mpls label one mask
label2_mask	(Optional) mpls label two mask
label3_mask	(Optional) mpls label three mask
label4_mask	(Optional) mpls label four mask
label1_any	(Optional) label one Any
label2_any	(Optional) label two Any
label3_any	(Optional) label three Any
label4_any	(Optional) label four Any
mpls	(Optional) mpls keyword
mpls_option	(Optional) mpls option
TABLE_mpls	(Optional)
TABLE_seqno	(Optional)
remark	(Optional) Remark String

Command Mode

/exec

show access-lists

show [ <ip_ipv6_mac> ] access-lists [ <name> ] [ capture session <capture_session> ] [ <expanded> | <summary> | <private> | <brief> | <stats-detail> ] [ __readonly__ TABLE_ip_ipv6_mac <op_ip_ipv6_mac> <show_summary> <acl_name> [ <statistics> ] [ <frag_opt_permit_deny> ] [ <global_capture_session> ] [ TABLE_seqno <seqno> { <permitdeny> [ <proto_str> | <proto> | <ip> | <ipv6> ] { <src_any> | <src_ip_prefix> | <src_ip_addr> <src_ip_mask> | <src_ipv6_prefix> | <src_ipv6_addr> <src_ipv6_mask> | <mac_src> <mac_src_wild> | <src_addrgrp> } [ <src_port_op> [ <src_port1_str> ] { <src_port1_num> } [ <src_port2_str> | <src_port2_num> ] | <src_portgrp> ] { <dest_any> | <dest_ip_prefix> | <dest_ip_addr> <dest_ip_mask> | <dest_ipv6_prefix> | <dest_ipv6_addr> <dest_ipv6_mask> | <mac_dest> <mac_dest_wild> | <dest_addrgrp> } [ <dest_port_op> [ <dest_port1_str> ] { <dest_port1_num> } [ <dest_port2_str> | <dest_port2_num> ] | <dest_portgrp> ] [ { <icmp_type> [ <icmp_code> ] | <icmp_str> } | { <icmpv6_type> [ <icmpv6_code> ] | <icmpv6_str> } ] [ <igmp_type> | <igmp_type_str> ] [ [ <precedence> | <precedence_str> ] [ <tos> | <tos_str> ] | [ <dscp> | <dscp_str> ] | [ <ttl> ] ] [ <log> ] [ <udfs> ] [ <capture_session> ] [ <fragments> ] [ <plen_op> <plen1> [ <plen2> ] ] [ <urg> ] [ <ack> ] [ <psh> ] [ <rst> ] [ <syn> ] [ <fin> ] [ <established> ] [ <http-method> | <http_opt_str> ] [ <tcp-option-length> ] [ <tcp-flags-mask> ] [ <flow_label> ] [ <timerange> ] [ <eth_proto> | <eth_proto_str> ] [ <vlan> ] [ <cos> ] [ <match_count> ] | [ TABLE_match <module> <module_match_count> ] | [ <nve_vni> ] | <remark> [ <action> <actionid> ] } ] [ ethertype <ethertypeid> | vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [ [ <stats_enabled> ] [ <frag_option> ] [ <ign_rtable> ] { <num_ace> } { <conf_if_header> } [ <conf_if> ] { <active_if_header> } [ <active_if> ] ] ]

Syntax Description


show	Show running system information
name	(Optional) List name
ip_ipv6_mac	(Optional) IP/IPv6/MAC
capture	(Optional) capture
session	(Optional) session
capture_session	(Optional) session id
op_ip_ipv6_mac	(Optional) IP/IPv6/MAC
access-lists	List access lists
show_summary	(Optional)
acl_name	(Optional) List name
__readonly__	(Optional)
TABLE_ip_ipv6_mac	(Optional)
frag_opt_permit_deny	(Optional) frag_op_type
ethertype	(Optional) Configure match based on ethertype
vlan	(Optional) Configure match based on vlan
ingress_intf	(Optional) Configure match based on ingress interface
vlan_priority	(Optional) Configure match based on priority
ethertypeid	(Optional) Configure the ethertype value
vlanid	(Optional) VLAN number
intfid	(Optional) Interface index
intfname	(Optional) Interface name
vlanpriorityid	(Optional) Vlan Priority
seqno	(Optional) Sequence number
permitdeny	(Optional) Permit/deny
proto	(Optional) A protocol number
TABLE_seqno	(Optional)
proto_str	(Optional) Protocol name
ip	(Optional) IP
ipv6	(Optional) IPV6
src_any	(Optional) SRCAny
dest_any	(Optional) DESTAny
src_ip_prefix	(Optional) Source IP prefix
src_ip_addr	(Optional) Source IP address
src_ip_mask	(Optional) Source IP mask
mac_src	(Optional) Source MAC address
mac_src_wild	(Optional) Source MAC mask
dest_ip_prefix	(Optional) Destination IP prefix
dest_ip_addr	(Optional) Destination IP address
dest_ip_mask	(Optional) Destination IP mask
mac_dest	(Optional) Destination MAC address
mac_dest_wild	(Optional) Destination MAC mask
src_port_op	(Optional) Source Port operator
dest_port_op	(Optional) Destination Port operator
src_port1_str	(Optional) Source port name
src_port1_num	(Optional) Source port number
src_port2_str	(Optional) Source port name
src_port2_num	(Optional) Source port number
dest_port1_str	(Optional) Destination port name
dest_port1_num	(Optional) Destination port number
dest_port2_str	(Optional) Destination port name
dest_port2_num	(Optional) Destination port number
icmp_type	(Optional) ICMP type
icmp_code	(Optional) ICMP code
icmp_str	(Optional) ICMP message
icmpv6_type	(Optional) ICMP type
icmpv6_code	(Optional) ICMP code
icmpv6_str	(Optional) ICMP message
igmp_type	(Optional) IGMP type
igmp_type_str	(Optional) IGMP type String
precedence	(Optional) precedence
precedence_str	(Optional) precedence string
tos	(Optional) tos
tos_str	(Optional) tos string
dscp	(Optional) dscp
dscp_str	(Optional) dscp string
udfs	(Optional) udfs string
ttl	(Optional) ttl
capture_session	(Optional) capture session
global_capture_session	(Optional) capture session
log	(Optional) Log
fragments	(Optional) Fragments
urg	(Optional) URG
ack	(Optional) ACK
psh	(Optional) PSH
rst	(Optional) RST
syn	(Optional) SYN
fin	(Optional) FIN
established	(Optional) ESTABLISHED
http-method	(Optional) http-method
http_opt_str	(Optional) http_option string
tcp-option-length	(Optional) TCP Option size
tcp-flags-mask	(Optional) TCP Flags mask
flow_label	(Optional) IPv6 flow label
timerange	(Optional) Time-range
eth_proto	(Optional) MAC protocol number
eth_proto_str	(Optional) MAC protocol name
vlan	(Optional) VLAN number
cos	(Optional) CoS value
match_count	(Optional) Number of packets matching the ACL
TABLE_match	(Optional)
module	(Optional) Module name
module_match_count	(Optional) Number of packets matching the ACL per module
nve_vni	(Optional) nve vni
remark	(Optional) Remark String
statistics	(Optional) STATISTICS
src_addrgrp	(Optional) Source address group
dest_addrgrp	(Optional) Destination address group
src_portgrp	(Optional) Source port group
dest_portgrp	(Optional) Destination port group
plen_op	(Optional) Source Port operator
plen1	(Optional) Packet length minimum
plen2	(Optional) packet length maximum
action	(Optional) Action
actionid	(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63> set-erspan-gre-proto: <1-65535>
stats_enabled	(Optional)
frag_option	(Optional)
ign_rtable	(Optional)
num_ace	(Optional) Total number of ACEs
conf_if_header	(Optional)
conf_if	(Optional) Configured Interfaces
active_if_header	(Optional)
active_if	(Optional) Active interfaces
expanded	(Optional) EXPANDED
summary	(Optional) SUMMARY
private	(Optional) PRIVATE
brief	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED
stats-detail	THIS KEYWORD OR VARIABLE IS NOT SUPPORTED

Command Mode

/exec

show accounting log

show accounting log [ { <i0> | start-time <SYYYY> <SMonth> <SDate> <STime> [ end-time <EYYYY> <EMonth> <EDate> <ETime> ] } ] [ __readonly__ [ TABLE_acctlog_time <accountlog_starttime> ] ]

Syntax Description


show	Show running system information
accounting	Show Accounting Information
log	Show Accounting Log
i0	(Optional) Log Size(in bytes)
start-time	(Optional) Show messages from a given start-time
SYYYY	(Optional) Enter year in YYYY format
SMonth	(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
SDate	(Optional) Enter day of month in dd format
STime	(Optional) Enter hour, minutes, seconds as HH:MM:SS
end-time	(Optional) Show messages from a given end-time
EYYYY	(Optional) Enter year in YYYY format
EMonth	(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
EDate	(Optional) Enter day of month in dd format
ETime	(Optional) Enter hour, minutes, seconds as HH:MM:SS
__readonly__	(Optional)
TABLE_acctlog_time	(Optional)
accountlog_starttime	(Optional) accounting log starttime

Command Mode

/exec

show accounting log all

show accounting log all [ __readonly__ [ TABLE_acctlog <accountlog_all> ] ]

Syntax Description


show	Show running system information
accounting	Show accounting configuration
log	Show Accounting Log
all	Display accounting log including show commands (Use <terminal log-all> to enable show command accounting)
__readonly__	(Optional)
TABLE_acctlog	(Optional)
accountlog_all	(Optional) accounting log all

Command Mode

/exec

show accounting log last-index

show accounting log last-index [ __readonly__ { <last_index> } ]

Syntax Description


show	Show running system information
accounting	Show accounting configuration
log	Show Accounting Log
last-index	Show accounting log last index information
__readonly__	(Optional)
last_index	(Optional) accounting log last index

Command Mode

/exec

show accounting log nvram

show accounting log nvram [ { <i0> | start-time <SYYYY> <SMonth> <SDate> <STime> [ end-time <EYYYY> <EMonth> <EDate> <ETime> ] } ] [ __readonly__ [ TABLE_acctnvramlog_time <accountnvramlog_starttime> ] ]

Syntax Description


show	Show running system information
accounting	Show Accounting Information
log	Show Accounting Log
nvram	present in nvram
i0	(Optional) Log Size(in bytes)
start-time	(Optional) Show messages from a given start-time
SYYYY	(Optional) Enter year in YYYY format
SMonth	(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
SDate	(Optional) Enter day of month in dd format
STime	(Optional) Enter hour, minutes, seconds as HH:MM:SS
end-time	(Optional) Show messages from a given end-time
EYYYY	(Optional) Enter year in YYYY format
EMonth	(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec
EDate	(Optional) Enter day of month in dd format
ETime	(Optional) Enter hour, minutes, seconds as HH:MM:SS
__readonly__	(Optional)
TABLE_acctnvramlog_time	(Optional)
accountnvramlog_starttime	(Optional) accounting log nvram starttime

Command Mode

/exec

show accounting log nvram last-index

show accounting log nvram last-index [ __readonly__ { <last_index> } ]

Syntax Description


show	Show running system information
accounting	Show accounting configuration
log	Show Accounting Log
nvram	present in nvram
last-index	Show accounting log last index information
__readonly__	(Optional)
last_index	(Optional) accounting log last index

Command Mode

/exec

show accounting log nvram start-seqnum

show accounting log nvram start-seqnum <SSEQNUM> [ end-seqnum <ESEQNUM> ] [ __readonly__ [ TABLE_acctnvramlog_seq <accountnvramlog_seq> ] ]

Syntax Description


show	Show running system information
accounting	Show Accounting Information
log	Show Accounting Log
nvram	present in nvram
start-seqnum	Show messages starting from a given sequence number
end-seqnum	(Optional) Show messages ending with a given sequence number
SSEQNUM	Enter Starting Sequence Number
ESEQNUM	(Optional) Enter Starting Sequence Number
__readonly__	(Optional)
TABLE_acctnvramlog_seq	(Optional)
accountnvramlog_seq	(Optional) accounting log nvram seqnum

Command Mode

/exec

show accounting log start-seqnum

show accounting log start-seqnum <SSEQNUM> [ end-seqnum <ESEQNUM> ] [ __readonly__ [ TABLE_acctlog_seq <accountlog_seq> ] ]

Syntax Description


show	Show running system information
accounting	Show Accounting Information
log	Show Accounting Log
start-seqnum	Show messages starting from a given sequence number
end-seqnum	(Optional) Show messages ending with a given sequence number
SSEQNUM	Enter Starting Sequence Number
ESEQNUM	(Optional) Enter Starting Sequence Number
__readonly__	(Optional)
TABLE_acctlog_seq	(Optional)
accountlog_seq	(Optional) accounting log seqnum

Command Mode

/exec

show acl status

show acl status [ __readonly__ [ <current_operation> [ <current_operation_stage> ] [ <current_operation_cli> ] <last_operation> [ <last_operation_status> ] [ <last_operation_cli> ] [ <current_acl> ] [ <current_ace> ] ] ]

Syntax Description


show	Show running system information
acl	Show information about acl
status	Shows the status of last acl operation
__readonly__	(Optional)
current_operation	(Optional) Current operation
current_operation_stage	(Optional) Current operation stage
current_operation_cli	(Optional) Current operation CLI
last_operation	(Optional) Last operation
last_operation_status	(Optional) Last operation status
last_operation_cli	(Optional) Last operation CLI
current_acl	(Optional) Access-list being modified
current_ace	(Optional) ACE rule being modified

Command Mode

/exec

show amt process

show amt process [ vrf { <vrf-name> | <vrf-known-name> } ] [ __readonly__ TABLE_vrf <vrf> <pid> <uuid> <q> <re4> <ge4> <re6> <ge6> <pi4> <ar4> <ag4> <ra4> <ga4> <dra4> <pi6> <ar6> <ag6> <ra6> <ga6> <dra6> <qqic4> <tc4> <tl4> <rc4> <rl4> <jp4> <qqic6> <tc6> <tl6> <rc6> <rl6> <jp6> <grm4> <gjp4> <gslp4> <gsl4> <grm6> <gjp6> <gslp6> <gsl6> ]

Syntax Description


show	Show running system information
amt	AMT show commands
vrf	(Optional) Display information for VRF
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
process	Display AMT process information
__readonly__	(Optional)
TABLE_vrf	(Optional)
vrf	(Optional)
pid	(Optional)
uuid	(Optional)
q	(Optional)
re4	(Optional)
ge4	(Optional)
re6	(Optional)
ge6	(Optional)
pi4	(Optional)
ar4	(Optional)
ag4	(Optional)
ra4	(Optional)
ga4	(Optional)
dra4	(Optional)
pi6	(Optional)
qqic4	(Optional)
tc4	(Optional)
tl4	(Optional)
rc4	(Optional)
rl4	(Optional)
jp4	(Optional)
qqic6	(Optional)
tc6	(Optional)
tl6	(Optional)
rc6	(Optional)
rl6	(Optional)
jp6	(Optional)
grm4	(Optional)
gjp4	(Optional)
gslp4	(Optional)
gsl4	(Optional)
grm6	(Optional)
gjp6	(Optional)
gslp6	(Optional)
gsl6	(Optional)

Command Mode

/exec

show amt vrf all

show amt vrf all [ __readonly__ TABLE_vrf <vrf> <cid> <ip_tid> <ipv6_tid> ]

Syntax Description


show	Show running system information
amt	AMT show commands
vrf	Display all VRFs AMT is configured in
all	Display all VRFs AMT is configured in
__readonly__	(Optional)
TABLE_vrf	(Optional)
vrf	(Optional)
cid	(Optional)
ip_tid	(Optional)
ipv6_tid	(Optional)

Command Mode

/exec

show archive log config

show archive log config { all | [ user <username> ] [ first-index <first_index> [ last-index <last_index> ] ] } [ __readonly__ [ TABLE_archivelog_time [ <archivelog_firstindex> ] ] ]

Syntax Description


show	Show running system information
archive	Show archive configuration
log	Show Archive Log
config	Show Config Logger information
all	List all the records in the config log
user	(Optional) List records for specific user in the config log
username	(Optional) Username
first-index	(Optional) The first record number to display
last-index	(Optional) The last record number to display
first_index	(Optional) config log first index
last_index	(Optional) config log last index
__readonly__	(Optional)
TABLE_archivelog_time	(Optional)
archivelog_firstindex	(Optional) archive log startindex

Command Mode

/exec

show arp access-lists

show arp access-lists [ <name> ] [ __readonly__ TABLE_arp <arp_name> [ TABLE_seqno <seqno> { <permitdeny> <reqresp> ip { { <sender_ip_any> | { { <sender_host> <sender_ip> | { <sender_net_ip> <sender_ip_mask> } } } } [ { <target_ip_any> | { { <target_host> <target_ip> | { <target_net_ip> <target_ip_mask> } } } } ] } mac { { <sender_mac_any> | { { <sender_mac_host> <sender_mac> | { <sender_net_mac> <sender_mac_mask> } } } } [ { <target_mac_any> | { { <target_mac_host> <target_mac> | { <target_net_mac> <target_mac_mask> } } } } ] } [ <arp_log> ] } | <remark> ] ] [ capture session <session-id> ]

Syntax Description


show	Show running system information
arp	ARP access-lists
access-lists	List access lists
name	(Optional) List name
__readonly__	(Optional)
arp_name	(Optional) Name of the ARP ACL
seqno	(Optional) Sequence number
permitdeny	(Optional) Permit/deny
ip	(Optional) Any IP protocol
TABLE_arp	(Optional)
TABLE_seqno	(Optional)
reqresp	(Optional) ARP_Request
sender_ip_any	(Optional) Any
sender_host	(Optional) Host
sender_ip	(Optional) IP address <a.b.c.d>
sender_net_ip	(Optional) IP address <a.b.c.d>
sender_ip_mask	(Optional) IP mask <a.b.c.d>
target_ip_any	(Optional) Any
target_host	(Optional) Host
target_ip	(Optional) IP address <a.b.c.d>
target_net_ip	(Optional) IP address <a.b.c.d>
target_ip_mask	(Optional) IP mask <a.b.c.d>
mac	(Optional) MAC configuration commands
sender_mac_any	(Optional) Any
sender_mac_host	(Optional) Host
sender_mac	(Optional) MAC address EEEE.EEEE.EEEE
sender_net_mac	(Optional) MAC address EEEE.EEEE.EEEE
sender_mac_mask	(Optional) MAC mask EEEE.EEEE.EEEE
target_mac_any	(Optional) Any
target_mac_host	(Optional) Host
target_mac	(Optional) MAC address EEEE.EEEE.EEEE
target_net_mac	(Optional) MAC address EEEE.EEEE.EEEE
target_mac_mask	(Optional) MAC mask EEEE.EEEE.EEEE
remark	(Optional) Remark String
arp_log	(Optional) Log
capture	(Optional) Enable packet capture on this filter for session
session	(Optional) Session ID <1-48> for this session
session-id	(Optional) Session ID <1-48> for this session

Command Mode

/exec

Cisco Nexus 3548 NX-OS Command Reference (Show Commands), Release 9.3(1)

Bias-Free Language

Book Title

Cisco Nexus 3548 NX-OS Command Reference (Show Commands), Release 9.3(1)

Chapter Title

A Show Commands

Results

Chapter: A Show Commands

A Show Commands

show aaa accounting

show aaa authentication

show aaa authentication login

show aaa authentication login ascii-authentication

show aaa authentication login error-enable

show aaa authentication login invalid-username-log

show aaa authorization

show aaa bypass-user

show aaa client radius statistics

show aaa groups

show aaa local user blocked

show aaa server radius statistics

show aaa user default-role

show access-list

show access-list database

show access-lists

show access-lists

show accounting log

show accounting log all

show accounting log last-index

show accounting log nvram

show accounting log nvram last-index

show accounting log nvram start-seqnum

show accounting log start-seqnum

show acl status

show amt process

show amt vrf all

show archive log config

show arp access-lists

Was this Document Helpful?

Contact Cisco