A Show Commands

show aaa accounting

show aaa accounting [ __readonly__ [ TABLE_acctMethods <service> <methods> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

accounting

Show accounting configuration

__readonly__

(Optional)

TABLE_acctMethods

(Optional)

service

(Optional) service type

methods

(Optional) Accounting methods configured for the application

Command Mode

  • /exec

show aaa authentication

show aaa authentication [ __readonly__ [ TABLE_AuthenMethods <service> <method> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

__readonly__

(Optional)

TABLE_AuthenMethods

(Optional)

service

(Optional) Service for which authentication is needed

method

(Optional) Authentication method used for the service

Command Mode

  • /exec

show aaa authentication login

show aaa authentication login { mschap | mschapv2 | chap } [ __readonly__ [ <mschap_status> ] [ <mschapv2_status> ] [ <chap_status> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

login

Show authentication login error message configuration

mschap

Show authentication login MSCHAP enable configuration

mschapv2

Show authentication login MSCHAP V2 enable configuration

chap

Show authentication login CHAP enable configuration

__readonly__

(Optional)

mschap_status

(Optional) mschap enabled or disabled

mschapv2_status

(Optional) mschapv2 enabled or disabled

chap_status

(Optional) chap enabled or disabled

Command Mode

  • /exec

show aaa authentication login ascii-authentication

show aaa authentication login ascii-authentication [ __readonly__ { <ascii_authen_status> } ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

login

Show authentication login message configuration

ascii-authentication

Show ascii-authentication configuration

__readonly__

(Optional)

ascii_authen_status

(Optional) ascii authentication status

Command Mode

  • /exec

show aaa authentication login error-enable

show aaa authentication login error-enable [ __readonly__ [ <status> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

login

Show authentication login error message configuration

error-enable

Show authentication login error message enable configuration

__readonly__

(Optional)

status

(Optional) login error-enable enabled or disabled

Command Mode

  • /exec

show aaa authentication login invalid-username-log

show aaa authentication login invalid-username-log [ __readonly__ [ <status> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

login

Show authentication login message configuration

invalid-username-log

Show invalid username log configuration

__readonly__

(Optional)

status

(Optional) login invalid-username-log enabled or disabled

Command Mode

  • /exec

show aaa authentication login password-aging

show aaa authentication login password-aging [ __readonly__ { <passwordAging_status> } ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authentication

Show authentication configuration

login

Show authentication login error message configuration

password-aging

Show password-aging enable configuration

__readonly__

(Optional)

passwordAging_status

(Optional) login password-aging

Command Mode

  • /exec

show aaa authorization

show aaa authorization [ all ] [ __readonly__ [ <pki_ssh_cert_author> <pki_ssh_pubkey_author> ] [ TABLE_cmd_methods <appl_subtype> <cmd_type> <methods> ] [ TABLE_app_methods <appl> <methods> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

authorization

Show authorization configuration

all

(Optional) Show all(include defaults configurations) authorization info

__readonly__

(Optional)

pki_ssh_cert_author

(Optional)

pki_ssh_pubkey_author

(Optional)

TABLE_cmd_methods

(Optional) table containing command authorization methods

appl_subtype

(Optional)

cmd_type

(Optional)

methods

(Optional)

TABLE_app_methods

(Optional) table containing application authorization methods

appl

(Optional)

methods

(Optional)

Command Mode

  • /exec

show aaa bypass-user

show aaa bypass-user [ <s0> ] [ __readonly__ [ <num_bypass_users> ] [ TABLE_bypassUsers <username> <account> <author> ] ]

Syntax Description

show

Show running system information

aaa

Show aaa information

bypass-user

Show bypass user information

s0

(Optional) Enter the username

__readonly__

(Optional)

num_bypass_users

(Optional) Number of bypass users configured

TABLE_bypassUsers

(Optional)

username

(Optional) Username

account

(Optional) Accounting Bypass

author

(Optional) Authorization bypass

Command Mode

  • /exec

show aaa groups

show aaa groups [ __readonly__ { TABLE_groups <group> } ]

Syntax Description

show

Show running system information

aaa

Show aaa information

groups

Show configured groups

__readonly__

(Optional)

TABLE_groups

(Optional) Table showing aaa groups

group

(Optional) Name of the group

Command Mode

  • /exec

show aaa local user blocked

show aaa local user blocked [ __readonly__ { TABLE_sessions <u_name> <u_state> } ]

Syntax Description

show

Show running system information

aaa

Configure aaa functions

local

Local username

user

Local system user

blocked

Display Blocked users

__readonly__

(Optional)

TABLE_sessions

(Optional) aaa local users blocked table

u_name

(Optional) Name of the user

u_state

(Optional) State of the user

Command Mode

  • /exec

show aaa user default-role

show aaa user default-role [ __readonly__ { default_role_status <udr_status> } ]

Syntax Description

show

Show running system information

aaa

Show aaa information

user

Remotely authenticated user

default-role

Default role assigned by aaa-admin for remote authentication

__readonly__

(Optional)

default_role_status

(Optional) user default role status

udr_status

(Optional) Status of user default role

Command Mode

  • /exec

show access-list

show { system internal | hardware } access-list { summary | [ vdc <vdc_id> ] { [ interface <if_name> | vlan <vlan_id> | inband table <table> ] [ { input | output } { config | { { entries | merge } [ detail ] } | statistics | l4ops | redirect | sampler } ] } } [ module <module> ] [ __readonly__ <type> <feature> <plcy_id> <src_ip> <src_mask> <dst_ip> <dst_mask> <proto> <l4ops> <action> <mac> <cos> <vlan> <l2_proto> <ethertype> [ TABLE_vdc <vdc-no> <vdc-type> <dir> <policy-type> <policy-id> <policy-name> ] [ TABLE_instance <inst> [ TABLE_tcam_resource_usage <tcam-no> <lbl> <hw-lbl-id> <bank> ] [ TABLE_class <class-type> <policies> <netflow-profile> <netflow-deny-profile> <tcam-entries> ] <l4-protocol-cam-entries> <mac-etype-proto-cam-entries> <lous> <tcp-flags-table-entries> <adjacency-entries> ] ]

Syntax Description

show

Show running system information

system

System-related show commands

internal

Commands for internal use

hardware

Show hardware information

access-list

Access Control List

summary

summary

vdc

(Optional) vdc id

vdc_id

(Optional) vdc_id

interface

(Optional) interface name

if_name

(Optional) display access list for the interface

vlan

(Optional) vlan_id

vlan_id

(Optional) vlan_id

inband

(Optional) inband interface

table

(Optional) vrf table number

table

(Optional) vrf table number

input

(Optional) input/ingress policies

output

(Optional) output/egress policies

config

(Optional) parsed policy software database

entries

(Optional) tcam entries

statistics

(Optional) aggregate statistics

l4ops

(Optional) l4 operations information

redirect

(Optional) redirect resource information

sampler

(Optional) with sampler details

merge

(Optional) tcam entries merge information

detail

(Optional) detailed information

module

(Optional) Slot/module

module

(Optional) Slot/module number

__readonly__

(Optional)

type

(Optional) policy type eg: ACL, QOS

feature

(Optional) feature type eg: RACL, VACL

plcy_id

(Optional) policy id

src_ip

(Optional) src ipv4 address

src_mask

(Optional) src mask

dst_ip

(Optional) dst ipv4 address

dst_mask

(Optional) dst mask

proto

(Optional) protocol eg: TCP, UDP ...

l4ops

(Optional) layer 4 operations

action

(Optional) action

mac

(Optional) mac address

cos

(Optional) acos value

vlan

(Optional) vlan id

l2_proto

(Optional) L2 protocol

ethertype

(Optional) ethertype

TABLE_vdc

(Optional) show for vdc

vdc-no

(Optional) vdc number

vdc-type

(Optional) VDC type-COPP etc

dir

(Optional) Policy Direction

policy-type

(Optional) Policy type

policy-id

(Optional) Policy id

policy-name

(Optional) Policy name

TABLE_instance

(Optional) show for an instance

inst

(Optional) instance number

TABLE_tcam_resource_usage

(Optional) TCAM resource usage

tcam-no

(Optional) tcam number

lbl

(Optional) lbl name

hw-lbl-id

(Optional) hw lbl id

bank

(Optional) bank number

TABLE_class

(Optional) table class

class-type

(Optional) Class type

policies

(Optional) Policy name

netflow-profile

(Optional) Netflow Profile

netflow-deny-profile

(Optional) Netflow Deny Profile

tcam-entries

(Optional) No. of TCAM entries

l4-protocol-cam-entries

(Optional) L4 protocol cam entries

mac-etype-proto-cam-entries

(Optional) No. of mac etype/proto cam entries

lous

(Optional) No. of LOU's

tcp-flags-table-entries

(Optional) No. of CP flags table entries

adjacency-entries

(Optional) No. of adjacency entries

Command Mode

  • /exec

show access-list database

show { system internal | hardware } access-list [ vdc <vdc_id> ] database { interface | vlan | policy | process } [ module <module> ] [ __readonly__ <if_idx> <vlan> <plcy_id> <process_info> ]

Syntax Description

show

Show running system information

system

System-related show commands

internal

Commands for internal use

hardware

Show hardware information

access-list

Access Control List

vdc

(Optional) vdc id

vdc_id

(Optional) vdc_id

database

Show memory database

interface

display interfaces/vlans in a vdc with policies

policy

display policies in a vdc

vlan

display vlans in a vdc

process

display process database in a vdc

module

(Optional) Slot/module

module

(Optional) Slot/module number

__readonly__

(Optional)

if_idx

(Optional) interface

vlan

(Optional) vlan

plcy_id

(Optional) policy id

process_info

(Optional) process information

Command Mode

  • /exec

show access-lists

show [ <ip_ipv6_mac> ] access-lists [ <name> ] [ capture session <capture_session> ] [ <expanded> | <summary> | <private> | <brief> ] [ __readonly__ TABLE_ip_ipv6_mac <op_ip_ipv6_mac> <show_summary> <acl_name> [ <statistics> ] [ <frag_opt_permit_deny> ] [ <global_capture_session> ] [ TABLE_seqno <seqno> { <permitdeny> [ <proto_str> | <proto> | <ip> | <ipv6> ] { <src_any> | <src_ip_prefix> | <src_ip_addr> <src_ip_mask> | <src_ipv6_prefix> | <src_ipv6_addr> <src_ipv6_mask> | <mac_src> <mac_src_wild> | <src_addrgrp> } [ <src_port_op> [ <src_port1_str> ] { <src_port1_num> } [ <src_port2_str> | <src_port2_num> ] | <src_portgrp> ] { <dest_any> | <dest_ip_prefix> | <dest_ip_addr> <dest_ip_mask> | <dest_ipv6_prefix> | <dest_ipv6_addr> <dest_ipv6_mask> | <mac_dest> <mac_dest_wild> | <dest_addrgrp> } [ <dest_port_op> [ <dest_port1_str> ] { <dest_port1_num> } [ <dest_port2_str> | <dest_port2_num> ] | <dest_portgrp> ] [ { <icmp_type> [ <icmp_code> ] | <icmp_str> } | { <icmpv6_type> [ <icmpv6_code> ] | <icmpv6_str> } ] [ <igmp_type> | <igmp_type_str> ] [ [ <precedence> | <precedence_str> ] [ <tos> | <tos_str> ] | [ <dscp> | <dscp_str> ] | [ <ttl> ] ] [ <log> ] [ <udfs> ] [ <capture_session> ] [ <fragments> ] [ <plen_op> <plen1> [ <plen2> ] ] [ <urg> ] [ <ack> ] [ <psh> ] [ <rst> ] [ <syn> ] [ <fin> ] [ <established> ] [ <http-method> | <http_opt_str> ] [ <tcp-option-length> ] [ <tcp-flags-mask> ] [ <flow_label> ] [ <timerange> ] [ <eth_proto> | <eth_proto_str> ] [ <vlan> ] [ <cos> ] [ <match_count> ] | [ <nve_vni> ] | <remark> [ <action> <actionid> ] } ] [ ethertype <ethertypeid> | vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [ <action> <actionid> ] [ [ <stats_enabled> ] [ <frag_option> ] { <num_ace> } { <conf_if_header> } [ <conf_if> ] { <active_if_header> } [ <active_if> ] ] ]

Syntax Description

show

Show running system information

name

(Optional) List name

ip_ipv6_mac

(Optional) IP/IPv6/MAC

capture

(Optional) capture

session

(Optional) session

capture_session

(Optional) session id

op_ip_ipv6_mac

(Optional) IP/IPv6/MAC

access-lists

List access lists

show_summary

(Optional)

acl_name

(Optional) List name

__readonly__

(Optional)

TABLE_ip_ipv6_mac

(Optional)

frag_opt_permit_deny

(Optional) frag_op_type

ethertype

(Optional) Configure match based on ethertype

vlan

(Optional) Configure match based on vlan

ingress_intf

(Optional) Configure match based on ingress interface

vlan_priority

(Optional) Configure match based on priority

ethertypeid

(Optional) Configure the ethertype value

vlanid

(Optional) VLAN number

intfid

(Optional) Interface index

intfname

(Optional) Interface name

vlanpriorityid

(Optional) Vlan Priority

seqno

(Optional) Sequence number

permitdeny

(Optional) Permit/deny

proto

(Optional) A protocol number

TABLE_seqno

(Optional)

proto_str

(Optional) Protocol name

ip

(Optional) IP

ipv6

(Optional) IPV6

src_any

(Optional) SRCAny

dest_any

(Optional) DESTAny

src_ip_prefix

(Optional) Source IP prefix

src_ip_addr

(Optional) Source IP address

src_ip_mask

(Optional) Source IP mask

mac_src

(Optional) Source MAC address

mac_src_wild

(Optional) Source MAC mask

dest_ip_prefix

(Optional) Destination IP prefix

dest_ip_addr

(Optional) Destination IP address

dest_ip_mask

(Optional) Destination IP mask

mac_dest

(Optional) Destination MAC address

mac_dest_wild

(Optional) Destination MAC mask

src_port_op

(Optional) Source Port operator

dest_port_op

(Optional) Destination Port operator

src_port1_str

(Optional) Source port name

src_port1_num

(Optional) Source port number

src_port2_str

(Optional) Source port name

src_port2_num

(Optional) Source port number

dest_port1_str

(Optional) Destination port name

dest_port1_num

(Optional) Destination port number

dest_port2_str

(Optional) Destination port name

dest_port2_num

(Optional) Destination port number

icmp_type

(Optional) ICMP type

icmp_code

(Optional) ICMP code

icmp_str

(Optional) ICMP message

icmpv6_type

(Optional) ICMP type

icmpv6_code

(Optional) ICMP code

icmpv6_str

(Optional) ICMP message

igmp_type

(Optional) IGMP type

igmp_type_str

(Optional) IGMP type String

precedence

(Optional) precedence

precedence_str

(Optional) precedence string

tos

(Optional) tos

tos_str

(Optional) tos string

dscp

(Optional) dscp

dscp_str

(Optional) dscp string

udfs

(Optional) udfs string

ttl

(Optional) ttl

capture_session

(Optional) capture session

global_capture_session

(Optional) capture session

log

(Optional) Log

fragments

(Optional) Fragments

urg

(Optional) URG

ack

(Optional) ACK

psh

(Optional) PSH

rst

(Optional) RST

syn

(Optional) SYN

fin

(Optional) FIN

established

(Optional) ESTABLISHED

http-method

(Optional) http-method

http_opt_str

(Optional) http_option string

tcp-option-length

(Optional) TCP Option size

tcp-flags-mask

(Optional) TCP Flags mask

flow_label

(Optional) IPv6 flow label

timerange

(Optional) Time-range

eth_proto

(Optional) MAC protocol number

eth_proto_str

(Optional) MAC protocol name

vlan

(Optional) VLAN number

cos

(Optional) CoS value

match_count

(Optional) Number of packets matching the ACL

nve_vni

(Optional) nve vni

remark

(Optional) Remark String

statistics

(Optional) STATISTICS

src_addrgrp

(Optional) Source address group

dest_addrgrp

(Optional) Destination address group

src_portgrp

(Optional) Source port group

dest_portgrp

(Optional) Destination port group

plen_op

(Optional) Source Port operator

plen1

(Optional) Packet length minimum

plen2

(Optional) packet length maximum

action

(Optional) Action

actionid

(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63> set-erspan-gre-proto: <1-65535>

stats_enabled

(Optional)

frag_option

(Optional)

num_ace

(Optional) Total number of ACEs

conf_if_header

(Optional)

conf_if

(Optional) Configured Interfaces

active_if_header

(Optional)

active_if

(Optional) Active interfaces

expanded

(Optional) EXPANDED

summary

(Optional) SUMMARY

private

(Optional) PRIVATE

brief

(Optional) BRIEF

Command Mode

  • /exec

show accounting log

show accounting log [ { <i0> | start-time <SYYYY> <SMonth> <SDate> <STime> [ end-time <EYYYY> <EMonth> <EDate> <ETime> ] } ] [ __readonly__ [ TABLE_acctlog_time <accountlog_starttime> ] ]

Syntax Description

show

Show running system information

accounting

Show Accounting Information

log

Show Accounting Log

i0

(Optional) Log Size(in bytes)

start-time

(Optional) Show messages from a given start-time

SYYYY

(Optional) Enter year in YYYY format

SMonth

(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec

SDate

(Optional) Enter day of month in dd format

STime

(Optional) Enter hour, minutes, seconds as HH:MM:SS

end-time

(Optional) Show messages from a given end-time

EYYYY

(Optional) Enter year in YYYY format

EMonth

(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec

EDate

(Optional) Enter day of month in dd format

ETime

(Optional) Enter hour, minutes, seconds as HH:MM:SS

__readonly__

(Optional)

TABLE_acctlog_time

(Optional)

accountlog_starttime

(Optional) accounting log starttime

Command Mode

  • /exec

show accounting log all

show accounting log all [ __readonly__ [ TABLE_acctlog <accountlog_all> ] ]

Syntax Description

show

Show running system information

accounting

Show accounting configuration

log

Show Accounting Log

all

Display accounting log including show commands (Use <terminal log-all> to enable show command accounting)

__readonly__

(Optional)

TABLE_acctlog

(Optional)

accountlog_all

(Optional) accounting log all

Command Mode

  • /exec

show accounting log last-index

show accounting log last-index [ __readonly__ { <last_index> } ]

Syntax Description

show

Show running system information

accounting

Show accounting configuration

log

Show Accounting Log

last-index

Show accounting log last index information

__readonly__

(Optional)

last_index

(Optional) accounting log last index

Command Mode

  • /exec

show accounting log nvram

show accounting log nvram [ { <i0> | start-time <SYYYY> <SMonth> <SDate> <STime> [ end-time <EYYYY> <EMonth> <EDate> <ETime> ] } ] [ __readonly__ [ TABLE_acctnvramlog_time <accountnvramlog_starttime> ] ]

Syntax Description

show

Show running system information

accounting

Show Accounting Information

log

Show Accounting Log

nvram

present in nvram

i0

(Optional) Log Size(in bytes)

start-time

(Optional) Show messages from a given start-time

SYYYY

(Optional) Enter year in YYYY format

SMonth

(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec

SDate

(Optional) Enter day of month in dd format

STime

(Optional) Enter hour, minutes, seconds as HH:MM:SS

end-time

(Optional) Show messages from a given end-time

EYYYY

(Optional) Enter year in YYYY format

EMonth

(Optional) Enter Month as Jan, Feb, Mar, ..., Oct, Nov, or Dec

EDate

(Optional) Enter day of month in dd format

ETime

(Optional) Enter hour, minutes, seconds as HH:MM:SS

__readonly__

(Optional)

TABLE_acctnvramlog_time

(Optional)

accountnvramlog_starttime

(Optional) accounting log nvram starttime

Command Mode

  • /exec

show accounting log nvram last-index

show accounting log nvram last-index [ __readonly__ { <last_index> } ]

Syntax Description

show

Show running system information

accounting

Show accounting configuration

log

Show Accounting Log

nvram

present in nvram

last-index

Show accounting log last index information

__readonly__

(Optional)

last_index

(Optional) accounting log last index

Command Mode

  • /exec

show accounting log nvram start-seqnum

show accounting log nvram start-seqnum <SSEQNUM> [ end-seqnum <ESEQNUM> ] [ __readonly__ [ TABLE_acctnvramlog_seq <accountnvramlog_seq> ] ]

Syntax Description

show

Show running system information

accounting

Show Accounting Information

log

Show Accounting Log

nvram

present in nvram

start-seqnum

Show messages starting from a given sequence number

end-seqnum

(Optional) Show messages ending with a given sequence number

SSEQNUM

Enter Starting Sequence Number

ESEQNUM

(Optional) Enter Starting Sequence Number

__readonly__

(Optional)

TABLE_acctnvramlog_seq

(Optional)

accountnvramlog_seq

(Optional) accounting log nvram seqnum

Command Mode

  • /exec

show accounting log start-seqnum

show accounting log start-seqnum <SSEQNUM> [ end-seqnum <ESEQNUM> ] [ __readonly__ [ TABLE_acctlog_seq <accountlog_seq> ] ]

Syntax Description

show

Show running system information

accounting

Show Accounting Information

log

Show Accounting Log

start-seqnum

Show messages starting from a given sequence number

end-seqnum

(Optional) Show messages ending with a given sequence number

SSEQNUM

Enter Starting Sequence Number

ESEQNUM

(Optional) Enter Starting Sequence Number

__readonly__

(Optional)

TABLE_acctlog_seq

(Optional)

accountlog_seq

(Optional) accounting log seqnum

Command Mode

  • /exec

show acl status

show acl status [ __readonly__ [ <status_log_string> ] ]

Syntax Description

show

Show running system information

acl

Show information about acl

status

Shows the status of last acl operation

__readonly__

(Optional)

status_log_string

(Optional) ppf entry string

Command Mode

  • /exec

show amt process

show amt process [ vrf { <vrf-name> | <vrf-known-name> } ] [ __readonly__ TABLE_vrf <vrf> <pid> <uuid> <q> <re4> <ge4> <re6> <ge6> <pi4> <ar4> <ag4> <ra4> <ga4> <dra4> <pi6> <ar6> <ag6> <ra6> <ga6> <dra6> <qqic4> <tc4> <tl4> <rc4> <rl4> <jp4> <qqic6> <tc6> <tl6> <rc6> <rl6> <jp6> <grm4> <gjp4> <gslp4> <gsl4> <grm6> <gjp6> <gslp6> <gsl6> ]

Syntax Description

show

Show running system information

amt

AMT show commands

vrf

(Optional) Display information for VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

process

Display AMT process information

__readonly__

(Optional)

TABLE_vrf

(Optional)

vrf

(Optional)

pid

(Optional)

uuid

(Optional)

q

(Optional)

re4

(Optional)

ge4

(Optional)

re6

(Optional)

ge6

(Optional)

pi4

(Optional)

ar4

(Optional)

ag4

(Optional)

ra4

(Optional)

ga4

(Optional)

dra4

(Optional)

pi6

(Optional)

qqic4

(Optional)

tc4

(Optional)

tl4

(Optional)

rc4

(Optional)

rl4

(Optional)

jp4

(Optional)

qqic6

(Optional)

tc6

(Optional)

tl6

(Optional)

rc6

(Optional)

rl6

(Optional)

jp6

(Optional)

grm4

(Optional)

gjp4

(Optional)

gslp4

(Optional)

gsl4

(Optional)

grm6

(Optional)

gjp6

(Optional)

gslp6

(Optional)

gsl6

(Optional)

Command Mode

  • /exec

show amt vrf all

show amt vrf all [ __readonly__ TABLE_vrf <vrf> <cid> <ip_tid> <ipv6_tid> ]

Syntax Description

show

Show running system information

amt

AMT show commands

vrf

Display all VRFs AMT is configured in

all

Display all VRFs AMT is configured in

__readonly__

(Optional)

TABLE_vrf

(Optional)

vrf

(Optional)

cid

(Optional)

ip_tid

(Optional)

ipv6_tid

(Optional)

Command Mode

  • /exec

show archive log config

show archive log config { all | [ user <username> ] [ first-index <first_index> [ last-index <last_index> ] ] } [ __readonly__ [ TABLE_archivelog_time [ <archivelog_firstindex> ] ] ]

Syntax Description

show

Show running system information

archive

Show archive configuration

log

Show Archive Log

config

Show Config Logger information

all

List all the records in the config log

user

(Optional) List records for specific user in the config log

username

(Optional) Username

first-index

(Optional) The first record number to display

last-index

(Optional) The last record number to display

first_index

(Optional) config log first index

last_index

(Optional) config log last index

__readonly__

(Optional)

TABLE_archivelog_time

(Optional)

archivelog_firstindex

(Optional) archive log startindex

Command Mode

  • /exec

show arp access-lists

show arp access-lists [ <name> ] [ __readonly__ TABLE_arp <arp_name> [ TABLE_seqno <seqno> { <permitdeny> <reqresp> ip { { <sender_ip_any> | { { <sender_host> <sender_ip> | { <sender_net_ip> <sender_ip_mask> } } } } [ { <target_ip_any> | { { <target_host> <target_ip> | { <target_net_ip> <target_ip_mask> } } } } ] } mac { { <sender_mac_any> | { { <sender_mac_host> <sender_mac> | { <sender_net_mac> <sender_mac_mask> } } } } [ { <target_mac_any> | { { <target_mac_host> <target_mac> | { <target_net_mac> <target_mac_mask> } } } } ] } [ <arp_log> ] } | <remark> ] ] [ capture session <session-id> ]

Syntax Description

show

Show running system information

arp

ARP access-lists

access-lists

List access lists

name

(Optional) List name

__readonly__

(Optional)

arp_name

(Optional) Name of the ARP ACL

seqno

(Optional) Sequence number

permitdeny

(Optional) Permit/deny

ip

(Optional) Any IP protocol

TABLE_arp

(Optional)

TABLE_seqno

(Optional)

reqresp

(Optional) ARP_Request

sender_ip_any

(Optional) Any

sender_host

(Optional) Host

sender_ip

(Optional) IP address <a.b.c.d>

sender_net_ip

(Optional) IP address <a.b.c.d>

sender_ip_mask

(Optional) IP mask <a.b.c.d>

target_ip_any

(Optional) Any

target_host

(Optional) Host

target_ip

(Optional) IP address <a.b.c.d>

target_net_ip

(Optional) IP address <a.b.c.d>

target_ip_mask

(Optional) IP mask <a.b.c.d>

mac

(Optional) MAC configuration commands

sender_mac_any

(Optional) Any

sender_mac_host

(Optional) Host

sender_mac

(Optional) MAC address EEEE.EEEE.EEEE

sender_net_mac

(Optional) MAC address EEEE.EEEE.EEEE

sender_mac_mask

(Optional) MAC mask EEEE.EEEE.EEEE

target_mac_any

(Optional) Any

target_mac_host

(Optional) Host

target_mac

(Optional) MAC address EEEE.EEEE.EEEE

target_net_mac

(Optional) MAC address EEEE.EEEE.EEEE

target_mac_mask

(Optional) MAC mask EEEE.EEEE.EEEE

remark

(Optional) Remark String

arp_log

(Optional) Log

capture

(Optional) Enable packet capture on this filter for session

session

(Optional) Session ID <1-48> for this session

session-id

(Optional) Session ID <1-48> for this session

Command Mode

  • /exec