Cisco Nexus 5000 Series NX-OS Security Command Reference

F Commands

This chapter describes the Cisco NX-OS security commands that begin with F.

feature (user role feature group)

To configure a feature in a user role feature group, use the feature command. To delete a feature in a user role feature group, use the no form of this command.

feature feature-name

no feature feature-name

Syntax Description

Command Default

None

Command Modes

User role feature group configuration mode

Command History

Usage Guidelines

Use the show role feature command to list the valid feature names to use in this command.

Examples

This example shows how to add features to a user role feature group:

switch(config)# role feature-group name SecGroup 

switch(config-role-featuregrp)# feature aaa 

switch(config-role-featuregrp)# feature radius 

switch(config-role-featuregrp)# feature tacacs 

This example shows how to remove a feature from a user role feature group:

switch(config)# role feature-group name MyGroup 

switch(config-role-featuregrp)# no feature callhome 

Related Commands

feature dhcp

To enable the Dynamic Host Configuration Protocol (DHCP) snooping feature on the device, use the feature dhcp command. To disable the DHCP snooping feature and remove all configuration related to DHCP snooping, use the no form of this command.

feature dhcp

no feature dhcp

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Usage Guidelines

The DHCP snooping feature is disabled by default. DHCP snooping can be enabled or disabled on VLANs.

If you have not enabled the DHCP snooping feature, commands related to DCHP snooping are unavailable.

Dynamic ARP inspection and IP Source Guard depend upon the DHCP snooping feature.

If you disable the DHCP snooping feature, the device discards all configuration related to DHCP snooping configuration, including the following features:

•DHCP snooping

•DHCP relay

•Dynamic ARP Inspection (DAI)

•IP Source Guard

If you want to turn off DHCP snooping and preserve configuration related to DHCP snooping, disable DHCP snooping globally with the no ip dhcp snooping command.

Access-control list (ACL) statistics are not supported if the DHCP snooping feature is enabled.

Examples

This example shows how to enable DHCP snooping:

switch(config)# feature dhcp 

switch(config)# 

This example shows how to disable DHCP snooping:

switch(config)# no feature dhcp 

switch(config)# 

Related Commands

feature http-server

To enable HTTP or Hypertext Transfer Protocol Secure (HTTPS) on the switch, use the feature http-server command. To disable the HTTP or HTTPS server, use the no form of this command.

feature http-server

no feature http-server

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Usage Guidelines

In releases earlier than Cisco NX-OS Release 5.0(2)N1(1), HTTP and HTTPS are enabled on the switch by default.

Examples

This example shows how to enable the HTTP server on the switch and verify the status of the HTTP server:

switch(config)# feature http-server 

switch(config)# exit 

switch# show feature 

Feature Name          Instance  State

--------------------  --------  --------

assoc_mgr             1         enabled

cimserver             1         disabled

dhcp-snooping         1         disabled

fabric-binding        1         disabled

fc-port-security      1         disabled

fcoe                  1         enabled

fcsp                  1         disabled

fex                   1         enabled

fport-channel-trunk   1         disabled

http-server           1         enabled

interface-vlan        1         enabled

lacp                  1         enabled

ldap                  1         disabled

lldp                  1         enabled

niv                   1         disabled

npiv                  1         disabled

npv                   1         disabled

otv                   1         disabled

port_track            1         disabled

private-vlan          1         enabled

privilege             1         enabled

sshServer             1         enabled

tacacs                1         enabled

telnetServer          1         enabled

udld                  1         enabled

vpc                   1         enabled

vtp                   1         enabled

switch# show http-server 

http-server enabled

switch# 

Related Commands

feature port-security

To enable port security on Layer 2 interfaces, use the feature port-security command. To disable port security, use the no form of this command.

feature port-security

no feature port-security

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Usage Guidelines

Use the port security feature to secure a port by limiting and identifying the MAC addresses of the switches that are allowed to access the port.

You can enable port security on a virtual port channel (vPC) port only if the following occurs:

•Port security is enabled on both the vPC peers

•Port security is enabled on the vPC port on both the vPC peers.

This command does not require a license.

Examples

This example shows how to enable port security on the switch:

switch# configure terminal

switch(config)# feature port-security

switch(config)#

This example shows how to disable port security on the switch:

switch# configure terminal

switch(config)# no feature port-security

switch(config)#

Related Commands

feature privilege

To enable the cumulative privilege of roles for command authorization on RADIUS and TACACS+ servers, use the feature privilege command. To disable the cumulative privilege of roles, use the no form of this command.

feature privilege

no feature privilege

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Usage Guidelines

When the feature privilege command is enabled, privilege roles inherit the permissions of lower level privilege roles.

Examples

This example shows how to enable the cumulative privilege of roles:

switch(config)# feature privilege 

switch(config)# 

This example shows how to disable the cumulative privilege of roles:

switch(config)# no feature privilege 

switch(config)# 

Related Commands

feature tacacs+

To enable TACACS+, use the feature tacacs+ command. To disable TACACS+, use the no form of this command.

feature tacacs+

no feature tacacs+

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Usage Guidelines

You must use the feature tacacs+ command before you configure TACACS+.

Note When you disable TACACS+, the Cisco NX-OS software removes the TACACS+ configuration.

Examples

This example shows how to enable TACACS+:

switch(config)# feature tacacs+

This example shows how to disable TACACS+:

switch(config)# no feature tacacs+

Related Commands