| Step 1
| Connect your PC
to the service port and configure an IPv4 address to use the same subnet as the
switch. The
switch is loaded with IOS XE image and the
service port interface is configured as gigabitethernet 0/0.
|
| Step 2
| Start Internet
Explorer 10 (or later), Firefox 2.0.0.11 (or later), or Google Chrome on your
PC and enter the management interface IP address on the browser window. The
management interface IP address is same as the gigabitethernet 0/0 (also known
as service port interface). When you log in for the first time, you need to
enter HTTP username and password. By default, the username is
admin and the
password is
cisco.
You can use both
HTTP and HTTPS when using the service port interface. HTTPS is enabled by
default and HTTP can also be enabled.
When you log in
for the first time, the
Accessing Cisco Switch
<Model Number> <Hostname> page appears.
|
| Step 3
| On the
Accessing Cisco
Switch page, click the
Wireless
Web GUI link to access
switch web GUI
Home page.
|
| Step 4
| Choose
to perform all steps that you
need to configure the
switch initially.
The
Admin
Users page appears.
|
| Step 5
| On the
Admin
Users page, enter the administrative username to be assigned to
this
switch in the User Name text box and the
administrative password to be assigned to this
switch in the Password and Confirm Password
text boxes. Click
Next.
The default
username is
admin and the
default password is
cisco. You can
also create a new administrator user for the
switch. You can enter up to 24 ASCII
characters for username and password.
The
SNMP
System Summary page appears.
|
| Step 6
| On the
SNMP
System Summary page, enter the following SNMP system parameters for
the
switch, and click
Next:
-
Customer-definable
switch location in the Location text box.
-
Customer-definable contact details such as phone number with
names in the Contact text box.
-
Choose
enabled to send SNMP notifications for various SNMP
traps or
disabled not to send SNMP notifications for various
SNMP traps from the SNMP Global Trap drop-down list.
-
Choose
enabled to send system log messages or
disabled not to send system log messages from the
SNMP Logging drop-down list.
| Note
|
The SNMP
trap server, must be reachable through the distribution ports (and not through
the gigabitethernet0/0 service or management interface).
|
The
Management Port page appears.
|
| Step 7
| In the
Management Port page, enter the following parameters
for the management port interface (gigabitethernet 0/0) and click
Next.
-
Interface
IP address that you assigned for the service port in the IP Address text box.
-
Network
mask address of the management port interface in the Netmask text box.
-
The IPv4
Dynamic Host Configuration Protocol (DHCP) address for the selected port in the
IPv4 DHCP Server text box.
The
Wireless Management page appears.
|
| Step 8
| In the
Wireless
Management page, enter the following wireless interface management
details, and click
Next.
-
Choose the
interface—VLAN, or Ten Gigabit Ethernet from the Select Interface drop-down
list.
-
VLAN tag
identifier, or 0 for no VLAN tag in the VLAN id text box.
-
IP address
of wireless management interface where access points are connected in the IP
Address text box.
-
Network
mask address of the wireless management interface in the Netmask text box.
-
DHCP IPv4
IP address in the IPv4 DHCP Server text box.
When selecting
VLAN as interface, you can specify the ports as –Trunk or Access ports from the
selected list displayed in the Switch Port Configuration text box.
The
RF
Mobility and Country Code page appears.
|
| Step 9
| In the
RF
Mobility and Country Code page, enter the RF mobility domain name
in the RF Mobility text box, choose current country code from the Country Code
drop-down list, and click
Next. From the GUI, you can select only one country
code.
| Note
| Before
configuring RF grouping parameters and mobility configuration, ensure that you
refer to the relevant conceptual content and then proceed with the
configuration.
|
The
Mobility Configuration page with mobility global
configuration settings appears.
|
| Step 10
| In the
Mobility Configuration page, view and enter the
following mobility global configuration settings, and click
Next.
-
Choose
Mobility Controller or
Mobility Agent from the Mobility Role drop-down
list:
-
If
Mobility Agent is chosen, enter the mobility controller IP address in the
Mobility Controller IP Address text box and mobility controller IP address in
the Mobility Controller Public IP Address text box.
-
If
Mobility Controller is chosen, then the mobility controller IP address and
mobility controller public IP address are displayed in the respective text
boxes.
-
Displays
mobility protocol port number in the Mobility Protocol Port text box.
-
Displays
the mobility switch peer group name in the Mobility Switch Peer Group Name text
box.
-
Displays
whether DTLS is enabled in the DTLS Mode text box.
DTLS is a
standards-track Internet Engineering Task Force (IETF) protocol based on TLS.
-
Displays
mobility domain identifier for 802.11 radios in the Mobility Domain ID for
802.11 radios text box.
-
The amount
of time (in seconds) between each ping request sent to an peer
switch in the Mobility Keepalive Interval
(1-30)sec text box.
Valid
range is from 1 to 30 seconds, and the default value is 10 seconds.
-
Number of
times a ping request is sent to an peer
switch before the peer is considered to be
unreachable in the Mobility Keepalive Count (3-20) text box.
The valid
range is from 3 to 20, and the default value is 3.
-
The DSCP
value that you can set for the mobility
switch in the Mobility Control Message DSCP
Value (0-63) text box.
The valid
range is 0 to 63, and the default value is 0.
-
Displays
the number of mobility switch peer group member configured in the Switch Peer
Group Members Configured text box.
The
WLANs page appears.
|
| Step 11
| In the
WLANs page, enter the following WLAN configuration
parameters, and click
Next.
-
WLAN
identifier in the WLAN ID text box.
-
SSID of
the WLAN that the client is associated with in the SSID text box.
-
Name of
the WLAN used by the client in the Profile Name text box.
The
802.11
Configuration page appears.
|
| Step 12
| In the
802.11
Configuration page, check either one or both 802.11a/n/ac and
802.11b/g/n check boxes to enable the 802.11 radios, and click
Next.
The
Set
Time page appears.
|
| Step 13
| In the
Set
Time page, you can configure the time and date on the
switch based on the following parameters,
and click
Next.
-
Displays
current timestamp on the
switch in the Current Time text box.
-
Choose
either Manual or NTP from the Mode drop-down list.
On using
the NTP server, all access points connected to the
switch, synchronizes its time based on the
NTP server settings available.
-
Choose
date on the
switch from the Year, Month, and Day
drop-down list.
-
Choose
time from the Hours, Minutes, and Seconds drop-down list.
-
Enter the
time zone in the Zone text box and select the off setting required when
compared to the current time configured on the
switch from the Offset drop-down list.
The
Save
Wizard page appears.
|
| Step 14
| In the
Save
Wizard page, you can review the configuration settings performed on
the
switch using these steps, and if you wish
to change any configuration value, click
Previous and navigate to that page.
You can save the
switch configuration created using the
wizard only if a success message is displayed for all the wizards. If the
Save
Wizard page displays errors, you must recreate the wizard for
initial configuration of the
switch.
|
Feedback