Release Notes for Cisco Catalyst 9500 Series Switches, Cisco IOS XE Cupertino 17.8.x

Introduction

Cisco Catalyst 9500 Series Switches and Cisco Catalyst 9500 Series Switches - High Performance are leading, fixed, core and aggregation enterprise switching platforms and have been purpose-built to address emerging trends in security, IoT, mobility, and cloud.

These switches deliver complete convergence in terms of ASIC architecture with Unified Access Data Plane (UADP) 2.0 on Cisco Catalyst 9500 Series Switches and UADP 3.0 on Cisco Catalyst 9500 Series Switches - High Performance. The platform runs an open Cisco IOS XE that supports model-driven programmability. This series forms the foundational building block for Software-Defined Access (SD-Access), which is Cisco’s lead enterprise architecture.


Note


With the introduction of the High Performance models in the series, there may be differences in the supported and unsupported features, limitations, and caveats that apply to the Cisco Catalyst 9500 Series Switches and Cisco Catalyst 9500 Series Switches - High Performance models. Throughout this release notes document, any such differences are expressly called out. If they are not, the information applies to all the models in the series.

Whats New in Cisco IOS XE Cupertino 17.8.1

Hardware Features in Cisco IOS XE Cupertino 17.8.1

There are no new hardware features in this release.

Software Features in Cisco IOS XE Cupertino 17.8.1

Software Features Introduced on All Models

Feature Name

Description and License Level Information

Enforce minimum length for Enable password

Introduces support for specifying AAA common criteria policy in the enable password command. Use the common-criteria policy keyword to enable this feature.


G8275.x Timing Profile

Introduces G8275.1 telecom profile for accurate delivery of phase and time synchronization. The G8275.1 specifies a profile for telecommunication applications based on IEEE 1588 PTP.

MACsec Fallback Key Support

The MACsec Fallback Key feature establishes an MKA session with the pre-shared fallback key whenever the PSK fails to establish a session because of key mismatch.


Optimized Layer 2 Multicast in BGP EVPN VXLAN Fabric

In a BGP EVPN VXLAN fabric, layer 2 multicast traffic is optimized both at the access level and within the VXLAN fabric. Optimized layer 2 multicast is restricted to a Layer 2 Virtual Network Instance (L2VNI), wherein the source and receivers are within the same Layer 2 domain.


Programmability

  • YANG Data Models

The following programmability features are introduced in this release:

  • YANG Data Models: For the list of Cisco IOS XE YANG models available with this release, navigate to: https://github.com/YangModels/yang/tree/master/vendor/cisco/xe/1781.

    Revision statements embedded in the YANG files indicate if there has been a model revision. The README.md file in the same GitHub location highlights changes that have been made in the release.

New on the WebUI

There are no new WebUI features in this release.

Software Features Introduced on Cisco Catalyst 9500 Series Switches

See Software Features Introduced on All Models for features in this release on Cisco Catalyst 9500 Series Switches.

Software Features Introduced on Cisco Catalyst 9500 Series Switches-High Performance

See Software Features Introduced on All Models for features in this release on Cisco Catalyst 9500 Series Switches.

Software Features Introduced on Cisco Catalyst 9500X Series Switches

Feature Name

Description and License Level Information

Enhanced Packet Capture

Introduces support for packet capture on the 9500X models of the Catalyst 9500 Series Switches. Packet Capture is an onboard packet capture facility that allows you to capture packets flowing to, through, and from the device.

Export Control Key for High Security (HSECK9 key)

Introduces support for the HSECK9 key on Cisco Catalyst 9500X Series Switches.

The HSECK9 key is an export-controlled license, which authorizes the use of cryptographic features that are restricted by U.S. export control laws. If you want to use a restricted cryptographic feature, an HSECK9 key is required.

On this platform, WAN MACsec is the cryptographic features that requires an HSECK9 key.

An HSECK9 key is required for each UDI where you want to configure and use the cryptographic feature. A Smart Licensing Authorization Code (SLAC) must be installed for each HSECK9 key that you want to use.


See System Management → Available Licenses and Smart Licensing Using Policy. Also see System Management Commands.


(DNA Advantage)

Flexible NetFlow

Introduces support for Flexible NetFlow on the 9500X models of the Catalyst 9500 Series Switches. The Flexible NetFlow feature uses flows to provide statistics for accounting, network monitoring, and network planning.


WAN MACsec compliance

Introduces WAN MACsec to extend MACsec support to the WAN.

This feature is supported only on C9500X-28C8D model of the Catalyst 9500 Series Switches.

Important Notes

Unsupported Features: All Models

  • Security

    • IPsec VPN

    • Virtual Routing and Forwarding-Aware (VRF-Aware) Web Authentication

    • MACsec switch-to-host connections in an overlay network.

  • System Management

    • Performance Monitoring (PerfMon)

Unsupported Features: Cisco Catalyst 9500 Series Switches

  • Cisco TrustSec

    • Cisco TrustSec Network Device Admission Control (NDAC) on Uplinks

  • Interface and Hardware

    • Network-Powered Lighting (including COAP Proxy Server, 2-event Classification, Perpetual PoE, Fast PoE)

    • Link Debounce Timer

    • M2 SATA Module

  • IP Addressing Services

    • GRE Redirection

    • VRRPv3: Object Tracking Integration

    • GRE IPv6 Tunnels

    • HSRP and Switch Stack

    • HSRP Groups and Clustering

  • IP Multicast Routing

    • Unicast over Point-to-Multipoint (P2MP)

    • Generic Routing Encapsulation (GRE)

    • Multicast over P2MP GRE

  • IP Routing

    • PIM Bidirectional Forwarding Detection (PIM BFD), PIM Snooping

    • Border Gateway Protocol (BGP) Additional Paths

    • OSPF NSR

    • OSPFv3 NSR

    • OSPFv2 Loop-Free Alternate IP Fast Reroute

  • Layer 2

    • Audio Engineering Society: AES67 Timing Profile

    • Q-in-Q on a Trunk Port

  • Multiprotocol Label Switching

    • Hierarchical VPLS with MPLS Access

  • Network Management

    • Flexible NetFlow

      • NetFlow v5 Export Protocol

      • 4-byte (32-bit) AS Number Support

      • TrustSec NetFlow IPv4 Security Group Access Control List (SGACL) Deny and Drop Export

  • Quality of Service

    • Classification (Layer 3 Packet Length, Time-to-Live (TTL))

    • Per queue policer support

    • Sharped profile enablement for egress per port queue

    • L2 Miss

    • Ingress Packet FIFO (IPF)

  • Security

    • Lawful Intercept

  • VLAN

    • QinQ VLAN Mapping

Unsupported Features: Cisco Catalyst 9500 Series Switches - High Performance

  • High Availability

    • Graceful Insertion and Removal

    • Switch Stacks

  • IP Multicast Routing

    • IPv6 Multicast and IPv6 Multicast over Point-to-Point GRE

  • IP Routing

    • Unicast and Multicast over Point-to-Multipoint GRE

    • BFD Multihop Support for IPv4 Static Routes

  • Multiprotocol Label Switching

    • MPLS Label Distribution Protocol (MPLS LDP) VRF-Aware Static Labels

    • VPLS Routed Pseudowire IRB(v4) Unicast

  • Network Management

    • Cisco Application Visibility and Control (AVC)

  • Quality of Service

    • QoS Options on GRE Tunnel Interfaces

  • Security

    • Wake-on-LAN (WoL)

  • System Management

    • Network-Based Application Recognition (NBAR) and Next-Generation NBAR (NBAR2)

Unsupported Features: Cisco Catalyst 9500X Series Switches

  • BGP EVPN VXLAN

    • Layer 2 Broadcast, Unknown Unicast, and Multicast (BUM) Traffic Forwarding using Ingress Replication

    • BUM Traffic Rate Limiting

    • Dynamic ARP inspection (DAI) and DHCP Rogue Server Protection

    • EVPN VXLAN Centralized Default Gateway

    • VXLAN-Aware Flexible Netflow

    • MPLS Layer 3 VPN Border Leaf Handoff

    • MPLS Layer 3 VPN Border Spine Handoff

    • VPLS over MPLS Border Leaf Handoff

    • VPLS over MPLS Border Spine Handoff

    • Interworking of Layer 3 TRM with MVPN Networks for IPv4 Traffic

    • Private VLANs (PVLANs)

    • BGP EVPN VXLAN with IPv6 in the Underlay (VXLANv6)

    • EVPN Microsegmentation

    • VRF aware NAT64 EVPN Fabric

  • Cisco Trustsec

    • Cisco TrustSec Meta Data Inline Tagging

    • Interface Scalable Group Tag (SGT) Tagging

    • Device SGT Tagging

    • SGT Inline Tagging

    • Cisco TrustSec Manual Configuration

    • Cisco TrustSec Security Association Protocol (SAP)

    • Cisco TrustSec Metadata Header Encapsulation

    • Cisco TrustSec VLAN to SGT Mapping

    • Local Device SGT Mapping

    • IPv6 Support for SGT and SGACL

    • Cisco TrustSec SGT Caching

  • High Availability

    • Secure StackWise Virtual

    • Cisco Nonstop Forwarding with Stateful Switchover

    • Graceful Insertion and Removal

    • Switch Stacks

  • Interface and Hardware

    • Per-port MTU

    • Link Debounce Timer

  • IP Addressing Services

    • Next Hop Resolution Protocol (NHRP)

    • Network Address Translation (NAT)

    • Web Cache Communication Protocol (WCCP)

    • Switchport Block Unknown Unicast and Switchport Block Unknown Multicast

    • IPv6 over IPv4 GRE Tunnels

    • Gateway Load Balancing Protocol (GLBP)

    • Message Session Relay Protocol (MSRP)

    • TCP MSS Adjustment

    • WCCP IPv4

    • GLBP

    • GRE IPv6 Tunnels

  • IP Multicast Routing

    • SDR Listener Support

    • Multicast Routing over GRE Tunnel

    • Multicast VLAN Registration (MVR) for IGMP Snooping

    • IPv6 Multicast over Point-to-Point GRE

    • IGMP Proxy

    • Bidirectional PIM

    • PIM Snooping

    • PIM Dense Mode State Refresh

    • MLD Snooping

    • Multicast VPN

    • MVPNv6

    • mVPN Extranet Support

    • MLDP-Based VPN

    • PIM Snooping

    • PIM Dense Mode

  • IP Routing

    • OSPFv2 Loop-Free Alternate IP Fast Reroute

    • EIGRP Loop-Free Alternate IP Fast Reroute

    • Policy-Based Routing (PBR)

    • PBR for IPv6

    • VRF-Aware PBR

    • Local PBR

    • Multipoint GRE

    • Web Cache Communication Protocol (WCCP)

    • Unicast Reverse Path Forwarding (uRPF)

  • Layer 2

    • Multi-VLAN Registration Protocol (MVRP)

    • Loop Detection Guard

    • Cross-Stack UplinkFast

    • Optional Spanning Tree Protocol

    • Precision Time Protocol (PTP)

    • Audio Engineering Society: AES67 Timing Profile

    • PTPv2 on Cisco StackWise Virtual

    • Fast UniDirectional Link Detection

    • UniDirectional Link Detection (UDLD)

    • IEEE 802.1Q Tunneling

    • One-to-One VLAN Mapping

    • Selective Q-in-Q

    • Q-in-Q on a Trunk Port

    • Audio Video Bridging (AVB): IEEE 802.1BA

    • Flexlink+

    • VLAN Load Balancing for FlexLink+

    • Preemption for VLAN Load Balancing

    • FlexLink+ Dummy Multicast Packets

  • Multiprotocol Label Switching

    • BGP Multipath Load Sharing for Both eBGP and iBGP in an MPLS VPN

    • MPLS Layer 2 VPN over GRE

    • MPLS Layer 3 VPN over GRE

    • Virtual Private LAN Service (VPLS)

    • VPLS Autodiscovery, BGP-based

    • VPLS Layer 2 Snooping: Internet Group Management Protocol or Multicast Listener Discovery

    • Hierarchical VPLS with Multiprotocol Label Switching Access

    • VPLS Routed Pseudowire IRB(v4) Unicast

    • MPLS VPN Inter-AS IPv4 BGP Label Distribution

    • Seamless Multiprotocol Label Switching

  • Network Management

    • ERSPAN and RSPAN

    • Flow-Based Switch Port Analyser

    • FRSPAN

    • IP Aware MPLS Netflow

    • NetFlow Version 5

    • VPN ID

  • Security

    • Lawful Intercept

    • MACsec:

      • MACSec Cipher announcement

      • Switch-to-host MACsec

      • Cisco TrustSec Security Association Protocol

      • Cisco TrustSec MACsec

      • Fallback Key

      • MACsec EAP-TLS

      • MACsec Downlink

    • MAC ACLs

    • Port ACLs

    • VLAN ACLs

    • IP Source Guard

    • Web-based Authentication

    • Port Security

    • Weighted Random Early Detection mechanism (WRED) Based on DSCP, PREC, or COS

    • IEEE 802.1x Port-Based Authentication

  • System Management

    • Unicast MAC Address Filtering

  • VLAN

    • Wired Dynamic PVLAN

    • Private VLANs

Complete List of Supported Features

For the complete list of features supported on a platform, see the Cisco Feature Navigator at: https://cfnng.cisco.com.

Choose the following in the context of the Cisco Catalyst 9500 Series Switches:

  • CAT9500: to see all the features supported on the C9500-12Q, C9500-16X, C9500-24Q, C9500-40X models

  • CAT9500 HIGH PERFORMANCE (32C, 32QC, 48Y4C, 24Y4C): to see all the features supported on the C9500-24Y4C, C9500-32C, C9500-32QC, and C9500-48Y4C models

  • CAT9500X: to see all the features supported on the C9500X-28C8D model

Accessing Hidden Commands

From Cisco IOS XE Fuji 16.8.1a, as an improved security measure, the way in which hidden commands can be accessed has changed.

Hidden commands have always been present in Cisco IOS XE, but were not equipped with CLI help. That is, entering a question mark (?) at the system prompt did not display the list of available commands. Hidden commands are only meant to assist Cisco TAC in advanced troubleshooting, and are not documented either.

From Cisco IOS XE Fuji 16.8.1a, hidden commands are available under:

  • Category 1: Hidden commands in Privileged or User EXEC mode. Enter the service internal command to access these commands.

  • Category 2: Hidden commands in one of the configuration modes (global, interface, and so on).

Further, the following points apply to hidden commands under Category 1 and 2:

  • The commands have CLI help. Enter a question mark (?) at the system prompt to display the list of available commands.

    Note: For Category 1, enter the service internal command before you enter the question mark; you do not have to do this for Category 2.

  • The system generates a %PARSER-5-HIDDEN syslog message when a hidden command is used. The following is an example:
    *Feb 14 10:44:37.917: %PARSER-5-HIDDEN: Warning!!! 'show processes memory old-header ' is a hidden command. 
    Use of this command is not recommended/supported and will be removed in future.

Apart from categories 1 and 2, there are other internal commands displayed on the CLI, for which the system does not generate the %PARSER-5-HIDDEN syslog message.


Note


We recommend that you use any hidden command only under TAC supervision.

If you find that you need to use a hidden command, open a TAC case for help with finding another way of collecting the same information as the hidden command (for a hidden EXEC mode command), or to configure the same functionality (for a hidden configuration mode command) using nonhidden commands.


Default Behaviour—All Models

Beginning from Cisco IOS XE Gibraltar 16.12.5 and later, do not fragment bit (DF bit) in the IP packet is always set to 0 for all outgoing RADIUS packets (packets that originate from the device towards the RADIUS server).

Default Interface Behaviour on Cisco Catalyst 9500 Series Switches - High Performance and Cisco Catalyst 9500X Series Switches Only

From Cisco IOS XE Gibraltar 16.11.1, the default interface for all High Performance and 9500X models in the series changes from Layer 3 to Layer 2. Use the no switchport command to change the Layer 2 interface into Layer 3 mode.

The startup configuration has explicit configuration of the switchport command for Layer 2 interfaces and the no switchport command for Layer 3 interfaces to address this change in behaviour and to support seamless migration.

Supported Hardware

Cisco Catalyst 9500 Series Switches—Model Numbers

The following table lists the supported hardware models and the default license levels they are delivered with. For more information about the available license levels, see section License Levels.

Base PIDs are the model numbers of the switch.

Bundled PIDs indicate the orderable part numbers for base PIDs that are bundled with a particular network module. Entering the show version , show module , or show inventory commands on such a switch (bundled PID), displays its base PID.

Table 1. Cisco Catalyst 9500 Series Switches

Switch Model

Default License Level1

Description

Base PIDs

C9500-12Q-E

Network Essentials

12 40-Gigabit Ethernet QSFP+ ports and two power supply slots

C9500-12Q-A

Network Advantage

C9500-16X-E

Network Essentials

16 1/10-Gigabit Ethernet SFP/SFP+ ports and two power supply slots

C9500-16X-A

Network Advantage

C9500-24Q-E

Network Essentials

24-Port 40-Gigabit Ethernet QSFP+ ports and two power supply slots

C9500-24Q-A

Network Advantage

C9500-40X-E

Network Essentials

40 1/10-Gigabit Ethernet SFP/SFP+ ports and two power supply slots

C9500-40X-A

Network Advantage

Bundled PIDs

C9500-16X-2Q-E

Network Essentials

16 10-Gigabit Ethernet SFP+ port switch and a 2-Port 40-Gigabit Ethernet (QSFP) network module on uplink ports

C9500-16X-2Q-A

Network Advantage

C9500-24X-E

Network Essentials

16 10-Gigabit Ethernet SFP+ port switch and an 8-Port 10-Gigabit Ethernet (SFP) network module on uplink ports

C9500-24X-A

Network Advantage

C9500-40X-2Q-E

Network Essentials

40 10-Gigabit Ethernet SFP+ port switch and a 2-Port 40-Gigabit Ethernet (QSFP) network module on uplink ports

C9500-40X-2Q-A

Network Advantage

C9500-48X-E

Network Essentials

40 10-Gigabit Ethernet SFP+ port switch and an 8-Port 10-Gigabit Ethernet (SFP) network module on uplink ports

C9500-48X-A

Network Advantage

1 See section LicensingTable: Permitted Combinations, in this document for information about the add-on licenses that you can order.
Table 2. Cisco Catalyst 9500 Series Switches-High Performance

Switch Model

Default License Level2

Description

C9500-24Y4C-E

Network Essentials

24 SFP28 ports that support 1/10/25-GigabitEthernet connectivity, four QSFP uplink ports that support 100/40-GigabitEthernet connectivity; two power supply slots.

C9500-24Y4C-A

Network Advantage

C9500-32C-E

Network Essentials

32 QSFP28 ports that support 40/100 GigabitEthernet connectivity; two power supply slots.

C9500-32C-A

Network Advantage

C9500-32QC-E

Network Essentials

32 QSFP28 ports, where you can have 24 ports that support 40-GigabitEthernet connectivity and 4 ports that support 100-GigabitEthernet connectivity, OR 32 ports that support 40-GigabitEthernet connectivity, OR 16 ports that support 100-GigabitEthernet connectivity; two power supply slots.

C9500-32QC-A

Network Advantage

C9500-48Y4C-E

Network Essentials

48 SFP28 ports that support 1/10/25-GigabitEthernet connectivity; four QSFP uplink ports that supports up to 100/40-GigabitEthernet connectivity; two power supply slots.

C9500-48Y4C-A

Network Advantage

2 See section LicensingTable: Permitted Combinations, in this document for information about the add-on licenses that you can order.
Table 3. Cisco Catalyst 9500X Series Switches

Switch Model

Default License Level3

Description

C9500X-28C8D-E

Network Essentials

28x100G QSFP28 and 8x400G QSFP-DD ports; two power supply slots

C9500X-28C8D-A

Network Advantage

C9500X-60L4D-A

Network Advantage

60x50G SFP56 and 4x400G QSFP-DD ports; two power supply slots

3 See section LicensingTable: Permitted Combinations, in this document for information about the add-on licenses that you can order.

Network Modules

The following table lists optional network modules for uplink ports available with some configurations .

Network Module

Description

C9500-NM-8X

Cisco Catalyst 9500 Series Network Module 8-port 1/10 Gigabit Ethernet with SFP/SFP+

Note the supported switch models (Base PIDs):

  • C9500-40X

  • C9500-16X

C9500-NM-2Q

Cisco Catalyst 9500 Series Network Module 2-port 40 Gigabit Ethernet with QSFP+

Note the supported switch models (Base PIDs):

  • C9500-40X

  • C9500-16X

Compatibility Matrix

The following table provides software compatibility information between Cisco Catalyst 9500 Series Switches, Cisco Identity Services Engine, Cisco Access Control Server, and Cisco Prime Infrastructure.

Catalyst 9500, 9500-High Performance and 9500X

Cisco Identity Services Engine

Cisco Access Control Server

Cisco Prime Infrastructure

Cupertino 17.8.1

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Cupertino 17.7.1

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.7

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.6a

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.6

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.5

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.4

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.3

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.2

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10 Downloads.

Bengaluru 17.6.1

3.1

3.0 latest patch

2.7 latest patch

2.6 latest patch

2.4 latest patch

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Bengaluru 17.5.1

3.0 Patch 1

2.7 Patch 2

2.6 Patch 7

2.4 Patch 13

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Bengaluru 17.4.1

3.0

2.7 Patch 2

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Amsterdam 17.3.8a

2.7

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10Downloads.

Amsterdam 17.3.8

2.7

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10Downloads.

Amsterdam 17.3.7

2.7

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10Downloads.

Amsterdam 17.3.6

2.7

-

PI 3.10 + PI 3.10 latest maintenance release + PI 3.10 latest device pack

See Cisco Prime Infrastructure 3.10Downloads.

Amsterdam 17.3.5

2.7

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Amsterdam 17.3.4

2.7

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Amsterdam 17.3.3

2.7

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 Downloads.

Amsterdam 17.3.2a

2.7

-

PI 3.8 + PI 3.8 latest maintenance release + PI 3.8 latest device pack

See Cisco Prime Infrastructure 3.8 Downloads.

Amsterdam 17.3.1

2.7

-

PI 3.8 + PI 3.8 latest maintenance release + PI 3.8 latest device pack

See Cisco Prime Infrastructure 3.8 Downloads.

Amsterdam 17.2.1

2.7

-

PI 3.7 + PI 3.7 latest maintenance release + PI 3.7 latest device pack

See Cisco Prime Infrastructure 3.7 Downloads.

Amsterdam 17.1.1

2.7

-

PI 3.6 + PI 3.6 latest maintenance release + PI 3.6 latest device pack

See Cisco Prime Infrastructure 3.6Downloads.

Gibraltar 16.12.8

2.6

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 → Downloads.

Gibraltar 16.12.7

2.6

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 → Downloads.

Gibraltar 16.12.6

2.6

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 → Downloads.

Gibraltar 16.12.5b

2.6

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 → Downloads.

Gibraltar 16.12.5

2.6

-

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9 → Downloads.

Gibraltar 16.12.4

2.6

-

PI 3.8 + PI 3.8 latest maintenance release + PI 3.8 latest device pack

See Cisco Prime Infrastructure 3.8 → Downloads.

Gibraltar 16.12.3a

2.6

-

PI 3.5 + PI 3.5 latest maintenance release + PI 3.5 latest device pack

See Cisco Prime Infrastructure 3.5Downloads.

Gibraltar 16.12.3

2.6

-

PI 3.5 + PI 3.5 latest maintenance release + PI 3.5 latest device pack

See Cisco Prime Infrastructure 3.5Downloads.

Gibraltar 16.12.2

2.6

-

PI 3.5 + PI 3.5 latest maintenance release + PI 3.5 latest device pack

See Cisco Prime Infrastructure 3.5Downloads.

Gibraltar 16.12.1

2.6

-

PI 3.5 + PI 3.5 latest maintenance release + PI 3.5 latest device pack

See Cisco Prime Infrastructure 3.5Downloads.

Gibraltar 16.11.1

2.6

2.4 Patch 5

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Gibraltar 16.10.1

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.8

2.5

2.1

5.4

5.5

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9Downloads.

Fuji 16.9.7

2.5

2.1

5.4

5.5

PI 3.9 + PI 3.9 latest maintenance release + PI 3.9 latest device pack

See Cisco Prime Infrastructure 3.9Downloads.

Fuji 16.9.6

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.5

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.4

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.3

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.2

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest maintenance release + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.9.1

2.3 Patch 1

2.4 Patch 1

5.4

5.5

PI 3.4 + PI 3.4 latest device pack

See Cisco Prime Infrastructure 3.4Downloads.

Fuji 16.8.1a

2.3 Patch 1

2.4

5.4

5.5

PI 3.3 + PI 3.3 latest maintenance release + PI 3.3 latest device pack

See Cisco Prime Infrastructure 3.3Downloads.

Everest 16.6.4a

2.2

2.3

5.4

5.5

PI 3.1.6 + Device Pack 13

See Cisco Prime Infrastructure 3.1Downloads.

Everest 16.6.4

2.2

2.3

5.4

5.5

PI 3.1.6 + Device Pack 13

See Cisco Prime Infrastructure 3.1Downloads.

Everest 16.6.3

2.2

2.3

5.4

5.5

PI 3.1.6 + Device Pack 13

See Cisco Prime Infrastructure 3.1Downloads

Everest 16.6.2

2.2

2.3

5.4

5.5

PI 3.1.6 + Device Pack 13

See Cisco Prime Infrastructure 3.1Downloads

Everest 16.6.1

2.2

5.4

5.5

PI 3.1.6 + Device Pack 13

See Cisco Prime Infrastructure 3.1Downloads

Everest 16.5.1a

2.1 Patch 3

5.4

5.5

-

Web UI System Requirements

The following subsections list the hardware and software required to access the Web UI:

Minimum Hardware Requirements

Processor Speed

DRAM

Number of Colors

Resolution

Font Size

233 MHz minimum4

512 MB5

256

1280 x 800 or higher

Small

4 We recommend 1 GHz
5 We recommend 1 GB DRAM

Software Requirements

Operating Systems

  • Windows 10 or later

  • Mac OS X 10.9.5 or later

Browsers

  • Google Chrome—Version 59 or later (On Windows and Mac)

  • Microsoft Edge

  • Mozilla Firefox—Version 54 or later (On Windows and Mac)

  • Safari—Version 10 or later (On Mac)

ROMMON Versions

ROMMON, also known as the boot loader, is firmware that runs when the device is powered up or reset. It initializes the processor hardware and boots the operating system software (Cisco IOS XE software image). The ROMMON is stored on the following Serial Peripheral Interface (SPI) flash devices on your switch:

  • Primary: The ROMMON stored here is the one the system boots every time the device is powered-on or reset.

  • Golden: The ROMMON stored here is a backup copy. If the one in the primary is corrupted, the system automatically boots the ROMMON in the golden SPI flash device.

ROMMON upgrades may be required to resolve firmware defects, or to support new features, but there may not be new versions with every release.

The following table provides ROMMON version information for the Cisco Catalyst 9500 Series Switches. For ROMMON version information of Cisco IOS XE 16.x.x releases, refer to the corresponding Cisco IOS XE 16.x.x release notes of the respective platform.

Release

ROMMON Version (C9500-12Q, C9500-24Q, C9500-16X, C9500-40X)

ROMMON Version (C9500-32C, C9500-32QC, C9500-24Y4C, C9500-48Y4C)

ROMMON Version (C9500X)

Cupertino 17.8.1

17.8.1r

17.7.1r[FC3]

17.8.1r

Cupertino 17.7.1

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.7

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.6a

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.6

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.5

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.4

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.3

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.2

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.6.1

17.6.1r[FC1]

17.6.1r

-

Bengaluru 17.5.1

17.5.1r

17.3.1r[FC2]

-

Bengaluru 17.4.1

17.4.1r

17.3.1r[FC2]

-

Amsterdam 17.3.8a

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.8

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.7

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.6

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.5

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.4

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.3

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.2a

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.3.1

17.3.1r[FC2]

17.3.1r[FC2]

-

Amsterdam 17.2.1

17.2.1r[FC1]

17.1.1[FC2]

-

Amsterdam 17.1.1

17.1.1r [FC1]

17.1.1[FC1]

-

Upgrading the Switch Software

This section covers the various aspects of upgrading or downgrading the device software.


Note


You cannot use the Web UI to install, upgrade, or downgrade device software.

Finding the Software Version

The package files for the Cisco IOS XE software are stored on the system board flash device (flash:).

You can use the show version privileged EXEC command to see the software version that is running on your switch.


Note


Although the show version output always shows the software image running on the switch, the model name shown at the end of this display is the factory configuration and does not change if you upgrade the software license.

You can also use the dir filesystem: privileged EXEC command to see the directory names of other software images that you might have stored in flash memory.

Software Images

Release

Image Type

File Name

Cisco IOS XE Cupertino 17.8.1

CAT9K_IOSXE

cat9k_iosxe.17.08.01.SPA.bin

No Payload Encryption (NPE)

cat9k_iosxe_npe.17.08.01.SPA.bin

Upgrading the ROMMON

To know the ROMMON or bootloader version that applies to every major and maintenance release, see ROMMON Versions.

You can upgrade the ROMMON before, or, after upgrading the software version. If a new ROMMON version is available for the software version you are upgrading to, proceed as follows:

  • Upgrading the ROMMON in the primary SPI flash device

    On the C9500-12Q, C9500-16X, C9500-24Q, C9500-40X models of the series, you must manually upgrade the ROMMON in the primary SPI flash device, if a new version is applicable, and the release you are upgrading from is Cisco IOS XE Gibraltar 16.12.1 or a later release. (So if you upgrade from Cisco IOS XE Gibraltar 16.11.1 for example, a manual upgrade does not apply; the ROMMON is automatically updated, if applicable). Enter the upgrade rom-monitor capsule primary switch command in privileged EXEC mode.

    On the C9500-24Y4C, C9500-32C, C9500-32QC, and C9500-48Y4C models of the series, this ROMMON is upgraded automatically. When you upgrade from an existing release on your switch to a later or newer release for the first time, and there is a new ROMMON version in the new release, the system automatically upgrades the ROMMON in the primary SPI flash device, based on the hardware version of the switch.

  • Upgrading the ROMMON in the golden SPI flash device

    You must manually upgrade this ROMMON. The manual upgrade applies to all models in the series. Enter the upgrade rom-monitor capsule golden switch command in privileged EXEC mode.


    Note


    • In case of a Cisco StackWise Virtual setup, upgrade the active and standby switch.


After the ROMMON is upgraded, it will take effect on the next reload. If you go back to an older release after this, the ROMMON is not downgraded. The updated ROMMON supports all previous releases.

Software Installation Commands

Summary of Software Installation Commands

Supported starting from Cisco IOS XE Everest 16.6.2 and later releases

To install and activate the specified file, and to commit changes to be persistent across reloads:

install add file filename [ activate commit]

To separately install, activate, commit, cancel, or remove the installation file: install ?

add file tftp: filename

Copies the install file package from a remote location to the device and performs a compatibility check for the platform and image versions.

activate [ auto-abort-timer]

Activates the file, and reloads the device. The auto-abort-timer keyword automatically rolls back image activation.

commit

Makes changes persistent over reloads.

rollback to committed

Rolls back the update to the last committed version.

abort

Cancels file activation, and rolls back to the version that was running before the current installation procedure started.

remove

Deletes all unused and inactive software installation files.


Note


The request platform software commands are deprecated starting from Cisco IOS XE Gibraltar 16.10.1. The commands are visible on the CLI in this release and you can configure them, but we recommend that you use the install commands to upgrade or downgrade.

Summary of request platform software Commands

Note

 
This table of commands is not supported on Cisco Catalyst 9500 Series Switches - High Performance.
Device# request platform software package ?

clean

Cleans unnecessary package files from media

copy

Copies package to media

describe

Describes package content

expand

Expands all-in-one package to media

install

Installs the package

uninstall

Uninstalls the package

verify

Verifies In Service Software Upgrade (ISSU) software package compatibility

Upgrading in Install Mode

Follow these instructions to upgrade from one release to another, using install commands, in install mode. To perform a software image upgrade, you must be booted into IOS through boot flash:packages.conf .

Before you begin

When upgrading from ...

Use these commands...

To upgrade to...

Cisco IOS XE Everest 16.5.1a or Cisco IOS XE Everest 16.6.1

Only request platform software commands

Cisco IOS XE Cupertino 17.8.x

Cisco IOS XE Everest 16.6.2 and all later releases

On Cisco Catalyst 9500 Series Switches, either install commands or request platform software commands6.

On Cisco Catalyst 9500 Series Switches - High Performance, only install commands7.

6 The request platform software commands are deprecated. So although they are still visible on the CLI, we recommend that you use install commands.
7 Introduced in Cisco IOS XE Fuji 16.8.1a.

The sample output in this section displays upgrade from Cisco IOS XE Cupertino 17.7.1 to Cisco IOS XE Cupertino 17.8.1 using install commands only.

Procedure


Step 1

Clean-up

install remove inactive

Use this command to clean-up old installation files in case of insufficient space and to ensure that you have at least 1GB of space in flash, to expand a new image.

The following sample output displays the cleaning up of unused files, by using the install remove inactive command:
Switch# install remove inactive
install_remove: START Wed Apr 6 19:51:48 UTC 2022
Cleaning up unnecessary package files
Scanning boot directory for packages ... done.
Preparing packages list to delete ...
    cat9k-cc_srdriver.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-espbase.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-guestshell.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-rpbase.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-rpboot.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-sipbase.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-sipspa.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-srdriver.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-webui.17.07.01.SPA.pkg
      File is in use, will not delete.
    cat9k-wlc.17.07.01.SPA.pkg
      File is in use, will not delete.
    packages.conf
      File is in use, will not delete.
  done.
The following files will be deleted:
[R0]:
/flash/cat9k-cc_srdriver.17.07.01.SPA.pkg
/flash/cat9k-espbase.17.07.01.SPA.pkg
/flash/cat9k-guestshell.17.07.01.SPA.pkg
/flash/cat9k-rpbase.17.07.01.SPA.pkg
/flash/cat9k-rpboot.17.07.01.SPA.pkg
/flash/cat9k-sipbase.17.07.01.SPA.pkg
/flash/cat9k-sipspa.17.07.01.SPA.pkg
/flash/cat9k-srdriver.17.07.01.SPA.pkg
/flash/cat9k-webui.17.07.01.SPA.pkg
/flash/cat9k-wlc.17.07.01.SPA.pkg
/flash/packages.conf
 
Do you want to remove the above files? [y/n]y
[R0]:
Deleting file flash:cat9k-cc_srdriver.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-espbase.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-guestshell.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-rpbase.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-rpboot.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-sipbase.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-sipspa.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-srdriver.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-webui.17.07.01.SPA.pkg ... done.
Deleting file flash:cat9k-wlc.17.07.01.SPA.pkg ... done.
Deleting file flash:packages.conf ... done.
SUCCESS: Files deleted.
--- Starting Post_Remove_Cleanup ---
Performing Post_Remove_Cleanup on all members
[1] Post_Remove_Cleanup package(s) on switch 1
[1] Finished Post_Remove_Cleanup on switch 1
Checking status of Post_Remove_Cleanup on [1]
Post_Remove_Cleanup: Passed on [1]
Finished Post_Remove_Cleanup
 
SUCCESS: install_remove Wed Apr 6 19:52:25 UTC 2022
Switch#

Step 2

Copy new image to flash

  1. copy tftp:[[//location]/directory]/filenameflash:

    Use this command to copy the new image from a TFTP server to flash memory. The location is either an IP address or a host name. The filename is specified relative to the directory used for file transfers. Skip this step if you want to use the new image from a TFTP server.
    Switch# copy tftp://10.8.0.6/image/cat9k_iosxe.17.08.01.SPA.bin flash:
    destination filename [cat9k_iosxe.17.08.01.SPA.bin]?
    Accessing tftp://10.8.0.6/image/cat9k_iosxe.17.08.01.SPA.bin...
    Loading /cat9k_iosxe.17.08.01.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0): 
    !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    [OK - 601216545 bytes]
     
    601216545 bytes copied in 50.649 secs (11870255 bytes/sec)
    
     
  2. dir flash:

    Use this command to confirm that the image has been successfully copied to flash.
    Switch# dir flash:*.bin
    Directory of flash:/*.bin
     
    Directory of flash:/
     
    434184 -rw- 601216545    Apr 6 2022 10:18:11 -07:00 cat9k_iosxe.17.08.01.SPA.bin
    11353194496 bytes total (8976625664 bytes free)
    
    

Step 3

Set boot variable

  1. boot system flash:packages.conf

    Use this command to set the boot variable to flash:packages.conf .
    Switch(config)# boot system flash:packages.conf
    
  2. no boot manual

    Use this command to configure the switch to auto-boot. Settings are synchronized with the standby switch, if applicable.
    Switch(config)# no boot manual
    Switch(config)# exit
  3. write memory

    Use this command to save boot settings.
    Switch# write memory
  4. show bootvar or show boot

    Use this command to verify the boot variable (packages.conf) and manual boot setting (no):
    Switch# show bootvar               <<on the C9500-24Y4C,C9500-32C, C9500-32QC, and C9500-48Y4C models
    BOOT variable = bootflash:packages.conf
    MANUAL_BOOT variable = no
    BAUD variable = 9600
    ENABLE_BREAK variable = yes
    BOOTMODE variable does not exist
    IPXE_TIMEOUT variable does not exist
    CONFIG_FILE variable = 
    
    Standby BOOT variable = bootflash:packages.conf
    Standby MANUAL_BOOT variable = no
    Standby BAUD variable = 9600
    Standby ENABLE_BREAK variable = yes
    Standby BOOTMODE variable does not exist
    Standby IPXE_TIMEOUT variable does not exist
    Standby CONFIG_FILE variable = 
    Switch# show boot                        <<on the C9500-12Q,C9500-16X C9500-24Q, and C9500-40X models
    Current Boot Variables:
    BOOT variable = flash:packages.conf;
    
    Boot Variables on next reload:
    BOOT variable = flash:packages.conf;
    Manual Boot = no
    Enable Break = yes
    Boot Mode = DEVICE
    iPXE Timeout = 0 

Step 4

Install image to flash

install add file activate commit

Use this command to install the image.

We recommend that you point to the source image on your TFTP server or the flash drive of the active switch, if you have copied the image to flash memory. If you point to an image on the flash or USB drive of a member switch (instead of the active), you must specify the exact flash or USB drive - otherwise installation fails. For example, if the image is on the flash drive of member switch 3 (flash-3): Switch# install add file flash-3:cat9k_iosxe.17.08.01.SPA.bin activate commit.

The following sample output displays installation of the Cisco IOS XE Cupertino 17.8.1 software image in the flash memory:
Switch# install add file flash:cat9k_iosxe.17.08.01.SPA.bin activate commit
install_add_activate_commit: Adding PACKAGE
install_add_activate_commit: Checking whether new add is allowed ....
--- Starting Add ---
Performing Add on Active/Standby
 [1] Add package(s) on R0
 [1] Finished Add on R0

Checking status of Add on [R0]
Add: Passed on [R0]
Finished Add

Image added. Version: 17.8.01

install_add_activate_commit: Activating PACKAGE
Following packages shall be activated:
/flash/cat9k-wlc.17.08.01.SPA.pkg
/flash/cat9k-webui.17.08.01.SPA.pkg
/flash/cat9k-srdriver.17.08.01.SPA.pkg
/flash/cat9k-sipspa.17.08.01.SPA.pkg
/flash/cat9k-sipbase.17.08.01.SPA.pkg
/flash/cat9k-rpboot.17.08.01.SPA.pkg
/flash/cat9k-rpbase.17.08.01.SPA.pkg
/flash/cat9k-guestshell.17.08.01.SPA.pkg
/flash/cat9k-espbase.17.08.01.SPA.pkg
/flash/cat9k-cc_srdriver.17.08.01.SPA.pkg

This operation may require a reload of the system. Do you want to proceed? [y/n] y

--- Starting Activate ---

Performing Activate on Active/Standby
[1] Activate package(s) on R0
    --- Starting list of software package changes ---
    Old files list:
      Removed cat9k-cc_srdriver.17.07.01.SPA.pkg
      Removed cat9k-espbase.17.07.01.SPA.pkg
      Removed cat9k-guestshell.17.07.01.SPA.pkg
      Removed cat9k-rpbase.17.07.01.SPA.pkg
      Removed cat9k-rpboot.17.07.01.SPA.pkg
      Removed cat9k-sipbase.17.07.01.SPA.pkg
      Removed cat9k-sipspa.17.07.01.SPA.pkg
      Removed cat9k-srdriver.17.07.01.SPA.pkg
      Removed cat9k-webui.17.07.01.SPA.pkg
      Removed cat9k-wlc.17.07.01.SPA.pkg
    New files list:
      Added cat9k-cc_srdriver.17.08.01.SSA.pkg
      Added cat9k-espbase.17.08.01.SSA.pkg
      Added cat9k-guestshell.17.08.01.SSA.pkg
      Added cat9k-lni.17.08.01.SSA.pkg
      Added cat9k-rpbase.17.08.01.SSA.pkg
      Added cat9k-rpboot.17.08.01.SSA.pkg
      Added cat9k-sipbase.17.08.01.SSA.pkg
      Added cat9k-sipspa.17.08.01.SSA.pkg
      Added cat9k-srdriver.17.08.01.SSA.pkg
      Added cat9k-webui.17.08.01.SSA.pkg
      Added cat9k-wlc.17.08.01.SSA.pkg
    Finished list of software package changes
  [1] Finished Activate on R0
Checking status of Activate on [R0]
Activate: Passed on [R0]
Finished Activate

--- Starting Commit ---
Performing Commit on Active/Standby
  [1] Commit package(s) on R0
  [1] Finished Commit on R0
Checking status of Commit on [R0]
Commit: Passed on [R0]
Finished Commit
Send model notification for install_add_activate_commit before reload
Install will reload the system now!
SUCCESS: install_add_activate_commit  Wed Apr 6 12:13:05 IST 2022

Switch#Apr 6 12:13:11.023: %PMANTACTION: F0/0vp: Process manager is exiting: n requested
Apr 6 12:13:11.028: %PMAN-5-EXITACTION: C1/0: pvp: Process manager is exiting: reload fru action requested
Apr 6 12:13:11.825: %PMAN-5-EXITACTION: R0/0: pvp: Process manager is exiting: reload action requested

Initializing Hardware...
System Bootstrap, Version 17.4.1r[FC2], RELEASE SOFTWARE (P)

Compiled 30-04-2022 12:00:00.00 by rel
Current ROMMON image : Primary Rommon Image
Last reset cause:LocalSoft
C9500-32QC platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt]  5     5     /-\|/-\|/-4     \|/-\|/-\|3     /-\|/-\|/-2     \|/-\|/-\|1     /-\|/-\|/-0     

boot: attempting to boot from [bootflash:packages.conf]

boot: reading file packages.conf
<output truncated>

Note

 
The system reloads automatically after executing the install add file activate commit command. You do not have to manually reload the system.

Step 5

Verify installation

After the software has been successfully installed, use the dir flash: command to verify that the flash partition has ten new .pkg files and two .conf files.

  1. dir flash:*.pkg

    The following is sample output of the dir flash:*.pkg command:
    Switch# dir flash:*.pkg
     
    Directory of flash:/
    475140 -rw- 2012104   Mar 18 2022 09:52:41 -07:00 cat9k-cc_srdriver.17.07.01.SPA.pkg
    475141 -rw- 70333380  Mar 18 2022 09:52:44 -07:00 cat9k-espbase.17.07.01.SPA.pkg
    475142 -rw- 13256     Mar 18 2022 09:52:44 -07:00 cat9k-guestshell.17.07.01.SPA.pkg
    475143 -rw- 349635524 Mar 18 2022 09:52:54 -07:00 cat9k-rpbase.17.07.01.SPA.pkg
    475149 -rw- 24248187  Mar 18 2022 09:53:02 -07:00 cat9k-rpboot.17.07.01.SPA.pkg
    475144 -rw- 25285572  Mar 18 2022 09:52:55 -07:00 cat9k-sipbase.17.07.01.SPA.pkg
    475145 -rw- 20947908  Mar 18 2022 09:52:55 -07:00 cat9k-sipspa.17.07.01.SPA.pkg
    475146 -rw- 2962372   Mar 18 2022 09:52:56 -07:00 cat9k-srdriver.17.07.01.SPA.pkg
    475147 -rw- 13284288  Mar 18 2022 09:52:56 -07:00 cat9k-webui.17.07.01.SPA.pkg
    475148 -rw- 13248     Mar 18 2022 09:52:56 -07:00 cat9k-wlc.17.07.01.SPA.pkg
    
    491524 -rw- 25711568  Apr 6 2022 11:49:33 -07:00 cat9k-cc_srdriver.17.08.01.SPA.pkg
    491525 -rw- 78484428  Apr 6 2022 11:49:35 -07:00 cat9k-espbase.17.08.01.SPA.pkg
    491526 -rw- 1598412   Apr 6 2022 11:49:35 -07:00 cat9k-guestshell.17.08.01.SPA.pkg
    491527 -rw- 404153288 Apr 6 2022 11:49:47 -07:00 cat9k-rpbase.17.08.01.SPA.pkg
    491533 -rw- 31657374  Apr 6 2022 11:50:09 -07:00 cat9k-rpboot.17.08.01.SPA.pkg
    491528 -rw- 27681740  Apr 6 2022 11:49:48 -07:00 cat9k-sipbase.17.08.01.SPA.pkg
    491529 -rw- 52224968  Apr 6 2022 11:49:49 -07:00 cat9k-sipspa.17.08.01.SPA.pkg
    491530 -rw- 31130572  Apr 6 2022 11:49:50 -07:00 cat9k-srdriver.17.08.01.SPA.pkg
    491531 -rw- 14783432  Apr 6 2022 11:49:51 -07:00 cat9k-webui.17.08.01.SPA.pkg
    491532 -rw- 9160      Apr 6 2022 11:49:51 -07:00 cat9k-wlc.17.08.01.SPA.pkg
    11353194496 bytes total (9544245248 bytes free)
    Switch#
    
    
  2. dir flash:*.conf

    The following is sample output of the dir flash:*.conf command. It displays the .conf files in the flash partition; note the two .conf files:

    • packages.conf—the file that has been re-written with the newly installed .pkg files

    • cat9k_iosxe.17.08.01.SPA.conf— a backup copy of the newly installed packages.conf file

    Switch# dir flash:*.conf
     
    Directory of flash:/*.conf
    Directory of flash:/
    
    434197 -rw- 7406 Apr 6 2022 10:59:16 -07:00 packages.conf
    516098 -rw- 7406 Apr 6 2022 10:58:08 -07:00 cat9k_iosxe.17.08.01.SPA.conf
    11353194496 bytes total (8963174400 bytes free)
     

Step 6

show version

After the image boots up, use this command to verify the version of the new image.

The following sample output of the show version command displays the Cisco IOS XE Cupertino 17.8.1 image on the device:
Switch# show version
Cisco IOS XE Software, Version 17.08.01
Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.8.1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
<output truncated>

Downgrading in Install Mode

Follow these instructions to downgrade from one release to another, in install mode.

Before you begin

Note that you can use this procedure for the following downgrade scenarios:

When downgrading from ...

Use these commands...

To downgrade to...

Cisco IOS XE Cupertino 17.8.x

  • On Cisco Catalyst 9500 Series Switches, either install commands or request platform software commands8.

  • On Cisco Catalyst 9500 Series Switches - High Performance, only install commands

Cisco IOS XE Cupertino 17.7.x or earlier releases.

8 The request platform software commands are deprecated. So although they are still visible on the CLI, we recommend that you use install commands.

Note


New switch models that are introduced in a release cannot be downgraded. The release in which a switch model is introduced is the minimum software version for that model.

The sample output in this section shows downgrade from Cisco IOS XE Cupertino 17.8.1 to Cisco IOS XE Cupertino 17.7.1, using install commands.

Procedure


Step 1

Clean-up

install remove inactive

Use this command to clean-up old installation files in case of insufficient space and to ensure that you have at least 1GB of space in flash, to expand a new image.

The following sample output displays the cleaning up of unused files, by using the install remove inactive command:
Switch# install remove inactive
 install_remove: START Wed Apr 6 11:42:27 IST 2022

Cleaning up unnecessary package files

No path specified, will use booted path bootflash:packages.conf

Cleaning bootflash:
  Scanning boot directory for packages ... done.
  Preparing packages list to delete ... 
    cat9k-cc_srdriver.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-espbase.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-guestshell.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-rpbase.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-rpboot.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-sipbase.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-sipspa.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-srdriver.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-webui.17.08.01.SSA.pkg
      File is in use, will not delete.
    cat9k-wlc.17.08.01.SSA.pkg
      File is in use, will not delete.
    packages.conf
      File is in use, will not delete.
  done.
SUCCESS: No extra package or provisioning files found on media. Nothing to clean.

SUCCESS: install_remove  Wed Apr 6 11:42:39 IST 2022

Step 2

Copy new image to flash

  1. copy tftp:[[//location]/directory]/filenameflash:

    Use this command to copy the new image from a TFTP server to flash memory. The location is either an IP address or a host name. The filename is specified relative to the directory used for file transfers. Skip this step if you want to use the new image from a TFTP server.
    Switch# copy tftp://10.8.0.6/image/cat9k_iosxe.17.07.01.SPA.bin flash:
    Destination filename [cat9k_iosxe.17.07.01.SPA.bin]?
    Accessing tftp://10.8.0.6//cat9k_iosxe.17.07.01.SPA.bin...
    Loading /cat9k_iosxe.17.07.01.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0): 
    !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    [OK - 508584771 bytes]
    508584771 bytes copied in 101.005 secs (5035244 bytes/sec)
     
    
  2. dir flash:

    Use this command to confirm that the image has been successfully copied to flash.
    Switch# dir flash:*.bin
    Directory of flash:/*.bin
     
    Directory of flash:/
     
    434184 -rw- 508584771 Apr 6 2022 13:35:16 -07:00 cat9k_iosxe.17.07.01.SPA.bin
    11353194496 bytes total (9055866880 bytes free)
    
    

Step 3

Set boot variable

  1. boot system flash:packages.conf

    Use this command to set the boot variable to flash:packages.conf .
    Switch(config)# boot system flash:packages.conf
    
  2. no boot manual

    Use this command to configure the switch to auto-boot. Settings are synchronized with the standby switch, if applicable.
    Switch(config)# no boot manual
    Switch(config)# exit
  3. write memory

    Use this command to save boot settings.
    Switch# write memory
  4. show bootvar or show boot

    Use this command to verify the boot variable (packages.conf) and manual boot setting (no):
    Switch# show bootvar               <<on the C9500-24Y4C,C9500-32C, C9500-32QC, and C9500-48Y4C models
    BOOT variable = bootflash:packages.conf
    MANUAL_BOOT variable = no
    BAUD variable = 9600
    ENABLE_BREAK variable = yes
    BOOTMODE variable does not exist
    IPXE_TIMEOUT variable does not exist
    CONFIG_FILE variable = 
    
    Standby BOOT variable = bootflash:packages.conf
    Standby MANUAL_BOOT variable = no
    Standby BAUD variable = 9600
    Standby ENABLE_BREAK variable = yes
    Standby BOOTMODE variable does not exist
    Standby IPXE_TIMEOUT variable does not exist
    Standby CONFIG_FILE variable = 
    Switch# show boot                        <<on the C9500-12Q,C9500-16X C9500-24Q, and C9500-40X models
    Current Boot Variables:
    BOOT variable = flash:packages.conf;
    
    Boot Variables on next reload:
    BOOT variable = flash:packages.conf;
    Manual Boot = no
    Enable Break = yes
    Boot Mode = DEVICE
    iPXE Timeout = 0 

Step 4

Downgrade software image

install add file activate commit

Use this command to install the image.

We recommend that you point to the source image on your TFTP server or the flash drive of the active switch, if you have copied the image to flash memory. If you point to an image on the flash or USB drive of a member switch (instead of the active), you must specify the exact flash or USB drive - otherwise installation fails. For example, if the image is on the flash drive of member switch 3 (flash-3): Switch# install add file flash-3:cat9k_iosxe.17.07.01.SPA.bin activate commit.

The following example displays the installation of the Cisco IOS XE Cupertino 17.7.1 software image to flash, by using the install add file activate commit command.
Switch# install add file flash:cat9k_iosxe.17.07.01.SPA.bin activate commit
install_add_activate_commit: Adding PACKAGE
install_add_activate_commit: Checking whether new add is allowed ....
--- Starting Add ---
Performing Add on Active/Standby
[1] Add package(s) on R0
[1] Finished Add on R0
Checking status of Add on [R0]
Add: Passed on [R0]
Finished Add
Image added. Version: 17.07.01.0.269
install_add_activate_commit: Activating PACKAGE

Following packages shall be activated:
/flash/cat9k-wlc.17.07.01.SPA.pkg
/flash/cat9k-webui.17.07.01.SPA.pkg
/flash/cat9k-srdriver.17.07.01.SPA.pkg
/flash/cat9k-sipspa.17.07.01.SPA.pkg
/flash/cat9k-sipbase.17.07.01.SPA.pkg
/flash/cat9k-rpboot.17.07.01.SPA.pkg
/flash/cat9k-rpbase.17.07.01.SPA.pkg
/flash/cat9k-guestshell.17.07.01.SPA.pkg
/flash/cat9k-espbase.17.07.01.SPA.pkg
/flash/cat9k-cc_srdriver.17.07.01.SPA.pkg

This operation may require a reload of the system. Do you want to proceed? [y/n] y


Performing Activate on Active/Standby
1] Activate package(s) on R0
    --- Starting list of software package changes ---
    Old files list:
      Removed cat9k-cc_srdriver.17.08.01.SSA.pkg
      Removed cat9k-espbase.17.08.01.SSA.pkg
      Removed cat9k-guestshell.17.08.01.SSA.pkg
      Removed cat9k-lni.17.08.01.SSA.pkg
      Removed cat9k-rpbase.17.08.01.SSA.pkg
      Removed cat9k-rpboot.17.08.01.SSA.pkg
      Removed cat9k-sipbase.17.08.01.SSA.pkg
      Removed cat9k-sipspa.17.08.01.SSA.pkg
      Removed cat9k-srdriver.17.08.01.SSA.pkg
      Removed cat9k-webui.17.08.01.SSA.pkg
      Removed cat9k-wlc.17.08.01.SSA.pkg
    New files list:
      Added cat9k-cc_srdriver.17.07.01.SPA.pkg
      Added cat9k-espbase.17.07.01.SPA.pkg
      Added cat9k-guestshell.17.07.01.SPA.pkg
      Added cat9k-rpbase.17.07.01.SPA.pkg
      Added cat9k-rpboot.17.07.01.SPA.pkg
      Added cat9k-sipbase.17.07.01.SPA.pkg
      Added cat9k-sipspa.17.07.01.SPA.pkg
      Added cat9k-srdriver.17.07.01.SPA.pkg
      Added cat9k-webui.17.07.01.SPA.pkg
      Added cat9k-wlc.17.07.01.SPA.pkg
    Finished list of software package changes
  [1] Finished Activate on R0
Checking status of Activate on [R0]
Activate: Passed on [R0]
Finished Activate

--- Starting Commit ---
Performing Commit on Active/Standby
 [1] Commit package(s) on R0
 [1] Finished Commit on R0
Checking status of Commit on [R0]
Commit: Passed on [R0]
Finished Commit

Send model notification for install_add_activate_commit before reload
Install will reload the system now!
SUCCESS: install_add_activate_commit  Wed Apr 6 11:51:01 IST 2022

Apr 6 11:51:07.505: %PMANTvp: Process manager is exiting: ren requested
Apr 6 11:51:07.505: %PMAN-5-EXITACTION: F0/0: pvp: Process manager is exiting: reload fru action requested
Apr 6 11:51:07.834: %PMAN-5-EXITACTION: R0/0: pvp: Process manager is exiting: reload action requested

Initializing Hardware...

System Bootstrap, Version 17.3.1r[FC2], RELEASE SOFTWARE (P)
Compiled 30-04-2022 12:00:00.00 by rel
Current ROMMON image : Primary Rommon Image

Last reset cause:LocalSoft
C9500-32QC platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt]  5     5     /-\|/-\|/-4     \|/-\|/-\|3     /-\|/-\|/-2     \|/-\|/-\|1     /-\|/-\|/-0     
boot: attempting to boot from [bootflash:packages.conf]
boot: reading file packages.conf

<output truncated>

Note

 
The system reloads automatically after executing the install add file activate commit command. You do not have to manually reload the system.

Step 5

Verify version

show version

After the image boots up, use this command to verify the version of the new image.

Note

 
When you downgrade the software image, the ROMMON version does not downgrade. It remains updated.
The following sample output of the show version command displays the Cisco IOS XE Cupertino 17.7.1 image on the device:
Switch# show version
Cisco IOS XE Software, Version 17.07.01
Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.7.1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
<output truncated>

Field-Programmable Gate Array Version Upgrade

A field-programmable gate array (FPGA) is a type of programmable memory device that exists on Cisco switches. They are re-configurable logic circuits that enable the creation of specific and dedicated functions.

To check the current FPGA version, enter the version -v command in ROMMON mode.


Note


  • Not every software release has a change in the FPGA version.

  • The version change occurs as part of the regular software upgrade and you do not have to perform any other additional steps.


Licensing

This section provides information about the licensing packages for features available on Cisco Catalyst 9000 Series Switches.

License Levels

The software features available on Cisco Catalyst 9500 Series Switches and Cisco Catalyst 9500 Series Switches - High Performance fall under these base or add-on license levels.

Base Licenses

  • Network Essentials

  • Network Advantage—Includes features available with the Network Essentials license and more.

Add-On Licenses

Add-On Licenses require a Network Essentials or Network Advantage as a pre-requisite. The features available with add-on license levels provide Cisco innovations on the switch, as well as on the Cisco Digital Network Architecture Center (Cisco DNA Center).

  • DNA Essentials

  • DNA Advantage— Includes features available with the DNA Essentials license and more.

To find information about platform support and to know which license levels a feature is available with, use Cisco Feature Navigator. To access Cisco Feature Navigator, go to https://cfnng.cisco.com. An account on cisco.com is not required.

Available Licensing Models and Configuration Information

  • Cisco IOS XE Fuji 16.8.x and earlier: RTU Licensing is the default and the only supported method to manage licenses.

  • Cisco IOS XE Fuji 16.9.1 to Cisco IOS XE Amsterdam 17.3.1: Smart Licensing is the default and the only supported method to manage licenses.


    Note


    On the Cisco Catalyst 9500 Series Switches-High Performance, it is from Cisco IOS XE Fuji 16.8.1a to Cisco IOS XE Amsterdam 17.3.1.


    In the software configuration guide of the required release, see System ManagementConfiguring Smart Licensing.

  • Cisco IOS XE Amsterdam 17.3.2a and later: Smart Licensing Using Policy, which is an enhanced version of Smart Licensing, is the default and the only supported method to manage licenses.

    In the software configuration guide of the required release (17.3.x onwards), see System ManagementSmart Licensing Using Policy.

For a more detailed overview on Cisco Licensing, go to cisco.com/go/licensingguide.

License Levels - Usage Guidelines

  • The duration or term for which a purchased license is valid:

    Smart Licensing Using Policy

    Smart Licensing

    • Perpetual: There is no expiration date for such a license.

    • Subscription: The license is valid only until a certain date (for a three, five, or seven year period).

    • Permanent: for a license level, and without an expiration date.

    • Term: for a license level, and for a three, five, or seven year period.

    • Evaluation: a license that is not registered.

  • Base licenses (Network Essentials and Network-Advantage) are ordered and fulfilled only with a perpetual or permanent license type.

  • Add-on licenses (DNA Essentials and DNA Advantage) are ordered and fulfilled only with a subscription or term license type.

  • An add-on license level is included when you choose a network license level. If you use DNA features, renew the license before term expiry, to continue using it, or deactivate the add-on license and then reload the switch to continue operating with the base license capabilities.

  • When ordering an add-on license with a base license, note the combinations that are permitted and those that are not permitted:

    Table 4. Permitted Combinations

    DNA Essentials

    DNA Advantage

    Network Essentials

    Yes

    No

    Network Advantage

    Yes9

    Yes

    9 You will be able to purchase this combination only at the time of the DNA license renewal and not when you purchase DNA-Essentials the first time.
  • Evaluation licenses cannot be ordered. They are not tracked via Cisco Smart Software Manager and expire after a 90-day period. Evaluation licenses can be used only once on the switch and cannot be regenerated. Warning system messages about an evaluation license expiry are generated only 275 days after expiration and every week thereafter. An expired evaluation license cannot be reactivated after reload. This applies only to Smart Licensing. The notion of evaluation licenses does not apply to Smart Licensing Using Policy.

Limitations and Restrictions

With Cisco Catalyst 9500 Series Switches and Cisco Catalyst 9500 Series Switches - High Performance—If a feature is not supported on a switch model, you do not have to factor in any limitations or restrictions that may be listed here. If limitations or restrictions are listed for a feature that is supported, check if model numbers are specified, to know if they apply. If model numbers are not specified, the limitations or restrictions apply to all models in the series.

  • Auto negotiation

    Auto negotiation (the speed auto command) and half duplex (the duplex half command) are not supported on GLC-T or GLC-TE transceivers for 10 Mbps and 100 Mbps speeds. This applies only to the C9500-48Y4C and C9500-24Y4C models of the series.

    We recommend not changing Forward Error Correction (FEC) when auto negotiation is ON. This is applicable to 100G/40G/25G CU cables on the C9500-32C, C9500-32QC, C9500-24Y4C and C9500-48Y4C models of the series.

  • Control Plane Policing (CoPP)—The show run command does not display information about classes configured under system-cpp policy, when they are left at default values. Use the show policy-map system-cpp-policy or the show policy-map control-plane commands in privileged EXEC mode instead.

  • Cisco StackWise Virtual

    • On Cisco Catalyst 9500 Series Switches, when Cisco StackWise Virtual is configured, breakout ports using 4X10G breakout cables, or the Cisco QSFP to SFP or SFP+ Adapter (QSA) module can only be used as data ports; they cannot be used to configure StackWise Virtual links (SVLs) or dual-active detective (DAD) links.

    • On Cisco Catalyst 9500 Series Switches - High Performance,

      • When Cisco StackWise Virtual is configured, breakout ports using 4X25G or 4X10G breakout cables can only be used as data ports; they cannot be used to configure SVLs or DAD links.

      • When Cisco StackWise Virtual is configured, Cisco QSA module with 10G SFP modules can be used as data ports and to configure SVLs or DAD links.

      • When Cisco StackWise Virtual is configured, Cisco QSA module with 1G SFP modules can be used as data ports and to configure DAD links; they cannot be used to configure SVLs since SVLs are not supported on 1G interfaces.

  • Cisco TrustSec restrictions—Cisco TrustSec can be configured only on physical interfaces, not on logical interfaces.

  • Flexible NetFlow limitations

    • You cannot configure NetFlow export using the Ethernet Management port (GigabitEthernet0/0).

    • You can not configure a flow monitor on logical interfaces, such as layer 2 port-channels, loopback, tunnels.

    • You can not configure multiple flow monitors of same type (ipv4, ipv6 or datalink) on the same interface for same direction.

  • Hardware Limitations — Optics:

    • 1G with Cisco QSA Module (CVR-QSFP-SFP10G) is not supported on the uplink ports of the C9500-24Y4C and C9500-48Y4C models.

    • Installation restriction for SFP-10G-T-X module on C9500-24Y4C and C9500-48Y4C— Only eight SFP-10G-T-X modules are supported at a time. If you insert a ninth SFP-10G-T-X module in a lower numbered port than the existing active eight SFP-10G-T-X module, a reload will bring up the ninth transceiver and moves the last existing port with SFP-10G-T-X module to error disabled state. This happens due to the order of sequence ports link bring up where the lower numbered port brings up the link first. This limitation applies in standalone and in Cisco StackWise Virtual setup with two C9500-24Y4C or C9500-48Y4C switches. Each switch can have eight SFP-10G-T-X modules.

      The following error displays on the console if you insert a ninth module with eight active modules:

      “%IOMD_ETHER_GEIM-4-MAX_LIMIT_XCVR: R0/0: iomd: Number of SFP-10G-T-X that can be supported has reached the max limit of 8, transceiver is err-disabled. Unplug the transceiver in interface TwentyFiveGigE1/0/29
    • SFP-10G-T-X supports 100Mbps/1G/10G speeds based on auto negotiation with the peer device. You cannot force speed settings from the transceiver.

  • Hardware limitations:

    • Use the MODE button to switch-off the beacon LED.

    • All port LED behavior is undefined until interfaces are fully initialized.

    • The following limitations apply to Cisco QSA Module (CVR-QSFP-SFP10G) when Cisco 1000Base-T Copper SFP (GLC-T) or Cisco 1G Fiber SFP Module for Multimode Fiber are plugged into the QSA module:

      • 1G Fiber modules over QSA do not support autonegotiation. Auto-negotiation should be disabled on the far-end devices.

      • Although visible in the CLI, the command [no] speed nonegotiate is not supported with 1G Fiber modules over QSA.

      • Only GLC-T over QSA supports auto-negotiation.

      • GLC-T supports only port speed of 1000 Mb/s over QSA. Port speeds of 10/100-Mb/s are not supported due to hardware limitation.

    • When you use Cisco QSFP-4SFP10G-CUxM Direct-Attach Copper Cables, autonegotiation is enabled by default. If the other end of the line does not support autonegotation, the link does not come up.

    • Autonegotiation is not supported on HundredGigabitEthernet1/0/49 to HundredGigabitEthernet1/0/52 uplink ports of the C9500-48Y4C models, and HundredGigabitEthernet1/0/25 to HundredGigabitEthernet1/0/28 uplink ports of the C9500-24Y4C models. Disable autonegotiation on the peer device if you are using QSFP-H40G-CUxx and QSFP-H40G-ACUxx cables.

    • For QSFP-H100G-CUxx cables, the C9500-48Y4C and C9500-24Y4C models support the cables only if both sides of the connection are either C9500-48Y4C or C9500-24Y4C.

    • For C9500-32C model, the power supply with serial number starting with POG has two fans and the power supply with serial number starting with QCS has a single fan. When you use show environment status command, the fan status of one fan is always displayed as N/A when the power supply with single fan is installed into the power supply slot. See Configuring Internal Power Supplies.

  • Interoperability limitations—When you use Cisco QSFP-4SFP10G-CUxM Direct-Attach Copper Cables, if one end of the 40G link is a Catalyst 9400 Series Switch and the other end is a Catalyst 9500 Series Switch, the link does not come up, or comes up on one side and stays down on the other. To avoid this interoperability issue between devices, apply the the speed nonegotiate command on the Catalyst 9500 Series Switch interface. This command disables autonegotiation and brings the link up. To restore autonegotiation, use the no speed nonegotiation command.

  • In-Service Software Upgrade (ISSU)

    • In-Service Software Upgrade (ISSU)—On Cisco Catalyst 9500 Series Switches (C9500-12Q, C9500-16X, C9500-24Q, C9500-40X), ISSU from Cisco IOS XE Fuji 16.9.x to Cisco IOS XE Gibraltar 16.10.x or to Cisco IOS XE Gibraltar 16.11.x is not supported.

    • On Cisco Catalyst 9500 Series Switches - High Performance (C9500-24Y4C, C9500-32C, C9500-32QC, and C9500-48Y4C), ISSU with Cisco StackWise Virtual is supported only starting from Cisco IOS XE Gibraltar 16.12.1. Therefore, ISSU upgrades can be performed only starting from this release to a later release.

    • While ISSU allows you to perform upgrades with zero downtime, we recommend you to do so during a maintenance window only.

    • If a new feature introduced in a software release requires a change in configuration, the feature should not be enabled during ISSU.

    • If a feature is not available in the downgraded version of a software image, the feature should be disabled before initiating ISSU.

  • QoS restrictions

    • When configuring QoS queuing policy, the sum of the queuing buffer should not exceed 100%.

    • Policing and marking policy on sub interfaces is supported.

    • Marking policy on witched virtual interfaces (SVI) is supported.

    • QoS policies are not supported for port-channel interfaces, tunnel interfaces, and other logical interfaces.

  • Secure Shell (SSH)

    • Use SSH Version 2. SSH Version 1 is not supported.

    • When the device is running SCP and SSH cryptographic operations, expect high CPU until the SCP read process is completed. SCP supports file transfers between hosts on a network and uses SSH for the transfer.

      Since SCP and SSH operations are currently not supported on the hardware crypto engine, running encryption and decryption process in software causes high CPU. The SCP and SSH processes can show as much as 40 or 50 percent CPU usage, but they do not cause the device to shutdown.

  • Smart Licensing Using Policy: Starting with Cisco IOS XE Amsterdam 17.3.2a, with the introduction of Smart Licensing Using Policy, even if you configure a hostname for a product instance or device, only the Unique Device Identifier (UDI) is displayed. This change in the display can be observed in all licensing utilities and user interfaces where the hostname was displayed in earlier releases. It does not affect any licensing functionality. There is no workaround for this limitation.

    The licensing utilities and user interfaces that are affected by this limitation include only the following: Cisco Smart Software Manager (CSSM), Cisco Smart License Utility (CSLU), and Smart Software Manager On-Prem (SSM On-Prem).

  • TACACS legacy command: Do not configure the legacy tacacs-server host command; this command is deprecated. If the software version running on your device is Cisco IOS XE Gibraltar 16.12.2 or a later release, using the legacy command can cause authentication failures. Use the tacacs server command in global configuration mode.

  • USB Authentication—When you connect a Cisco USB drive to the switch, the switch tries to authenticate the drive against an existing encrypted preshared key. Since the USB drive does not send a key for authentication, the following message is displayed on the console when you enter password encryption aes command:
    Device(config)# password encryption aes
    Master key change notification called without new or old key
  • MACsec is not supported on Software-Defined Access deployments.

  • VLAN Restriction—It is advisable to have well-defined segregation while defining data and voice domain during switch configuration and to maintain a data VLAN different from voice VLAN across the switch stack. If the same VLAN is configured for data and voice domains on an interface, the resulting high CPU utilization might affect the device.

  • Wired Application Visibility and Control limitations:

    • NBAR2 (QoS and Protocol-discovery) configuration is allowed only on wired physical ports. It is not supported on virtual interfaces, for example, VLAN, port channel nor other logical interfaces.

    • NBAR2 based match criteria ‘match protocol’ is allowed only with marking or policing actions. NBAR2 match criteria will not be allowed in a policy that has queuing features configured.

    • ‘Match Protocol’: up to 256 concurrent different protocols in all policies.

    • NBAR2 and Legacy NetFlow cannot be configured together at the same time on the same interface. However, NBAR2 and wired AVC Flexible NetFlow can be configured together on the same interface.

    • Only IPv4 unicast (TCP/UDP) is supported.

    • AVC is not supported on management port (Gig 0/0)

    • NBAR2 attachment should be done only on physical access ports. Uplink can be attached as long as it is a single uplink and is not part of a port channel.

    • Performance—Each switch member is able to handle 500 connections per second (CPS) at less than 50% CPU utilization. Above this rate, AVC service is not guaranteed.

    • Scale—Able to handle up to 5000 bi-directional flows per 24 access ports and 10000 bi-directional flows per 48 access ports.

  • YANG data modeling limitation—A maximum of 20 simultaneous NETCONF sessions are supported.

  • Embedded Event Manager—Identity event detector is not supported on Embedded Event Manager.

  • On the C9500X-28C8D model of the Cisco Catalyst 9500 Series Switches, TCAM space will not be reserved for different features. The available TCAM space will be shared across the features.

  • The File System Check (fsck) utility is not supported in install mode.

Caveats

Caveats describe unexpected behavior in Cisco IOS-XE releases. Caveats listed as open in a prior release are carried forward to the next release as either open or resolved.

Cisco Bug Search Tool

The Cisco Bug Search Tool (BST) allows partners and customers to search for software bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. The BST is designed to improve the effectiveness in network risk management and device troubleshooting. The tool has a provision to filter bugs based on credentials to provide external and internal bug views for the search input.

To view the details of a caveat, click on the identifier.

Open Caveats in Cisco IOS XE Cupertino 17.8.x

Identifier

Applicable Models

Headline

CSCwb35186

Catalyst 9500

Cat9500: CISCO-ENTITY-SENSOR-MIB is returning wrong threshold values for thermal sensors

Resolved Caveats in Cisco IOS XE Cupertino 17.8.1

There are no resolved caveats in this release.

Troubleshooting

For the most up-to-date, detailed troubleshooting information, see the Cisco TAC website at this URL:

https://www.cisco.com/en/US/support/index.html

Go to Product Support and select your product from the list or enter the name of your product. Look under Troubleshoot and Alerts, to find information for the problem that you are experiencing.

Related Documentation

Information about Cisco IOS XE at this URL: https://www.cisco.com/c/en/us/products/ios-nx-os-software/ios-xe/index.html

All support documentation for Cisco Catalyst 9500 Series Switches is at this URL: https://www.cisco.com/c/en/us/support/switches/catalyst-9500-series-switches/tsd-products-support-series-home.html

Cisco Validated Designs documents at this URL: https://www.cisco.com/go/designzone

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs

Communications, Services, and Additional Information

  • To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.

  • To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.

  • To submit a service request, visit Cisco Support.

  • To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco Marketplace.

  • To obtain general networking, training, and certification titles, visit Cisco Press.

  • To find warranty information for a specific product or product family, access Cisco Warranty Finder.

Cisco Bug Search Tool

Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software.