Supported MIBs

This appendix lists the supported management information base (MIBs) for this release on the Cisco ME 3400E Ethernet Access switch. It contains these sections:

•MIB List

•Using FTP to Access the MIB Files

MIB List

•BRIDGE-MIB (RFC1493)

Note The BRIDGE-MIB supports the context of a single VLAN. By default, SNMP messages using the configured community string always provide information for VLAN 1. To obtain the BRIDGE-MIB information for other VLANs, for example VLAN x, use this community string in the SNMP message: configured community string @x.

•CISCO-CABLE-DIAG-MIB

•CISCO-CDP-MIB

•CISCO-CONFIG-COPY-MIB

•CISCO-CONFIG-MAN-MIB

•CISCO-DHCP-SNOOPING-MIB

•CISCO-ENTITY-ALARM-MIB

•CISCO-ENTITY-FRU-CONTROL-MIB

•CISCO-ENTITY-SENSOR MIB

•CISCO-ENTITY-VENDORTYPE-OID-MIB

•CISCO-ENVMON-MIB

•CISCO-ERR-DISABLE-MIB

•CISCO-ETHER-CFM-MIB

•CISCO-ETHERNET-ACCESS-MIB

•CISCO-FLASH-MIB (Flash memory on all switches is modeled as removable flash memory.)

•CISCO-FTP-CLIENT-MIB

•CISCO-HSRP-MIB

Note Layer 3 MIBs are available only when the metro IP access image is running on the switch.

•CISCO-HSRP-EXT-MIB (partial support)

•CISCO-IGMP-FILTER-MIB

•CISCO-IMAGE-MIB

•CISCO-IPSLA-ETHERNET-MIB

Note Available only when the metro IP access image is running on the switch.

•CISCO-L2L3-INTERFACE-CONFIG-MIB

•CISCO-LAG-MIB

•CISCO-MAC-NOTIFICATION-MIB

•CISCO-MEMORY-POOL-MIB

•CISCO-NAC-NAD-MIB

•CISCO-PAE-MIB

•CISCO-PAGP-MIB

•CISCO-PING-MIB

•CISCO-PORT-QOS-MIB (the cportQosStats Table returns the values from the octets and packet counters, depending on switch configuration)

•CISCO-PRODUCTS-MIB

•CISCO-PROCESS-MIB

•CISCO-RTTMON-MIB

•CISCO-SMI-MIB

•CISCO-STACKMAKER-MIB

•CISCO-STP-EXTENSIONS-MIB

•CISCO-SYSLOG-MIB

•CISCO-TC-MIB

•CISCO-TCP-MIB

•CISCO-UDLDP-MIB

•CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB

•CISCO-VLAN-MEMBERSHIP-MIB

•CISCO-VTP-MIB

•ENTITY-MIB

•ETHERLIKE-MIB

•IEEE8021-PAE-MIB

•IEEE8023-LAG-MIB

•IF-MIB (In and out counters for VLANs are not supported.)

•IGMP-MIB

•INET-ADDRESS-MIB

•IPMROUTE-MIB

•LLDP MIB

•OLD-CISCO-CHASSIS-MIB

•OLD-CISCO-FLASH-MIB

•OLD-CISCO-INTERFACES-MIB

•OLD-CISCO-IP-MIB

•OLD-CISCO-SYS-MIB

•OLD-CISCO-TCP-MIB

•OLD-CISCO-TS-MIB

•PIM-MIB

•RFC1213-MIB (Functionality is as per the agent capabilities specified in the CISCO-RFC1213-CAPABILITY.my.)

•RFC1253-MIB (OSPF-MIB)

•RMON-MIB

•RMON2-MIB

•SNMP-FRAMEWORK-MIB

•SNMP-MPD-MIB

•SNMP-NOTIFICATION-MIB

•SNMP-TARGET-MIB

•SNMPv2-MIB

•TCP-MIB

•UDP-MIB

Note You can use this URL for a list of supported MIBs for Cisco products:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
You can access other information about MIBs and Cisco products on the Cisco web site:
ftp://nm-tac.cisco.com/pub/mib_repo/

Using FTP to Access the MIB Files

You can obtain each MIB file by using this procedure:

Step 1 Make sure that your FTP client is in passive mode.

Note Some FTP clients do not support passive mode.

Step 2 Use FTP to access the server ftp.cisco.com.

Step 3 Log in with the username anonymous.

Step 4 Enter your e-mail username when prompted for the password.

Step 5 At the ftp> prompt, change directories to /pub/mibs/v1 and /pub/mibs/v2.

Step 6 Use the get MIB_filename command to obtain a copy of the MIB file.