Cisco Emergency Responder Version 12.5(1)SU1 Release Notes
Introduction
Cisco Emergency Responder Release 12.5(1)SU1 supports the following new features:
Enhanced Location Tracking for Jabber Clients
Enhanced Location tracking allows Cisco Emergency Responder to track the Wireless Jabber Clients registered to Unified Communications Manager and identify them behind Corporate defined Access Points and provide corresponding ERL Treatment.
Note |
Wireless Jabber Clients (12.6) registered to Unified Communications Manager release 12.5(1)SU1 can be tracked behind Access Points in Emergency Responder from release 12.5(1) SU1 and onwards. |
FIPS Mode Support and Enhancement
FIPS Mode and Enhanced Security Mode do not support MD5 or DES encryption methods. From 12.5(1)SU1 release onwards, when in FIPS Mode or Enhanced Security Mode, SNMPv3 encryption settings allow encryption methods using SHA1 or AES-128 only.
Switch Support
Supports Catalyst 9200 and 9200L models. For more information, see the "Supported Voice-Ready LAN Switches" section.
Requirements
Supported Hardware and Software
The information in the following sections discuss Hardware and Software requirements for Cisco Emergency Responder 12.5(1)SU1. Read these sections before you perform an upgrade.
Required Software
The following table lists required software that you must install to use Emergency Responder.
Item |
Supported Software Release |
Description |
---|---|---|
Cisco Unified Communications Manager |
|
The software that runs the telephony network. |
Web Browser |
|
We recommend that you use the latest version for all the web browsers supported. |
Recommended Software
The following table lists optional software that is recommended for use with Emergency Responder.
Item |
Minimum software release |
Description |
---|---|---|
Email server |
Any SMTP email server |
Used to send email notifications to onsite alert (security) personnel. If you use an SMTP email paging server, personnel are paged instead of emailed. |
Supported Phones
The following table lists the different types of phones that support Emergency Responder. The support that Emergency Responder supplies differs depending on the type of phone and the type of switch port to which the phone is attached.
Phones |
Description |
||||
---|---|---|---|---|---|
Phones that are automatically tracked using Cisco Discovery Protocol
|
These phones do not require any special Emergency Responder configuration. However, you must enable Cisco Discovery Protocol on the switches.
|
||||
Phones that you can track using IP subnet
|
To track these phones, you must configure the subnet and then assign ERLs to the configured subnets.
|
||||
Phones that you can manually define or track using IP subnet
|
These phones are supported only if their calls are routed by Cisco Unified Communications Manager.
Cisco Webex client (registered natively to Unified Communications Manager) is represented through the registered Spark RD (Remote Destination) and needs to be manually defined in Emergency Responder for tracking. |
||||
Phones supported for off-premises location confirmation and update with the Remote Worker Emergency Calling feature in Unified Communications Manager 9.0 and later
|
When configured for off-premises use in Unified Communications Manager 9.0 and later, these phones provide displays for off-premises users to confirm or update their off-premises location.
|
||||
Phones supported for Access Point based tracking with Unified Communications Manager 11.5 and later Cisco Unified Wireless IP Phone 7925G, 7925G-EX, 7926G, 8821, Cisco Jabber, and Webex App |
Wireless Access Points need to be defined in Unified Communications Manager 11.5 and later, these phones provide their upstream infrastructure information (like BSSID) through Station Info messages to Unified Communications Manager. Cisco Emergency Responder through AXL Change Notification can track these phones through the associated Access Point. |
Supported Voice Ready Lan Switches
The following table lists the LAN switch models that Emergency Responder supports. A LAN switch model is supported only if the SNMP System Object ID appears in this table, regardless of the LAN switch configuration or software release.
Note |
Emergency Responder requires SNMP Version 1, Version 2, Version 2c, or Version 3 for automatic tracking of Cisco Unified IP Phones by connected switch ports. |
Series (Ethernet Ports Only) |
Supported Device |
System Object ID from CISCO-PRODUCTS-MIB or CISCO-STACK-MIB |
---|---|---|
Catalyst 2940 |
2940-8TF |
1.3.6.1.4.1.9.1.542 |
2940-8TT |
1.3.6.1.4.1.9.1.540 |
|
Catalyst 2950 |
2950-12 |
1.3.6.1.4.1.9.1.323 |
2950-24 |
1.3.6.1.4.1.9.1.324 |
|
2950C-24 |
1.3.6.1.4.1.9.1.325 |
|
2950G-24-EI-DC |
1.3.6.1.4.1.9.1.472 |
|
2950S-24 |
1.3.6.1.4.1.9.1.430 |
|
2950SX-24 |
1.3.6.1.4.1.9.1.480 |
|
2950SX-48 |
1.3.6.1.4.1.9.1.560 |
|
Catalyst 2960 |
2960-24LT-L |
1.3.6.1.4.1.9.1.951 |
2960-24PC-L |
1.3.6.1.4.1.9.1.950 |
|
2960-24-S |
1.3.6.1.4.1.9.1.929 |
|
2960-24TC-L |
1.3.6.1.4.1.9.1.694 |
|
2960-24TC-S |
1.3.6.1.4.1.9.1.928 |
|
2960-24TT-L |
1.3.6.1.4.1.9.1.716 |
|
2960-48PST-L |
1.3.6.1.4.1.9.1.1016 |
|
2960-48TC-L |
1.3.6.1.4.1.9.1.695 |
|
2960-48TC-S |
1.3.6.1.4.1.9.1.927 |
|
2960-48TT-L |
1.3.6.1.4.1.9.1.717 |
|
2960-8TC-L |
1.3.6.1.4.1.9.1.798 |
|
2960-8TC-S |
1.3.6.1.4.1.9.1.1006 |
|
2960G-24TC-L |
1.3.6.1.4.1.9.1.696 |
|
2960G-48TC-L |
1.3.6.1.4.1.9.1.697 |
|
2960G-8TC-L |
1.3.6.1.4.1.9.1.799 |
|
2960PD-8TT-L |
1.3.6.1.4.1.9.1.952 |
|
2960-48PST-S |
1.3.6.1.4.1.9.1.1148 |
|
2960-24LC-S |
1.3.6.1.4.1.9.1.1146 |
|
2960-24PC-S |
1.3.6.1.4.1.9.1.1147 |
|
Catalyst 2960-C |
2960CPD-8PT-L |
1.3.6.1.4.1.9.1.1315 |
2960C-8PC-L |
1.3.6.1.4.1.9.1.1366 |
|
2960C-12PC-L |
1.3.6.1.4.1.9.1.1367 |
|
Catalyst 2960-Plus |
2960-Plus 48PST-L |
1.3.6.1.4.1.9.1.1748 |
2960-Plus 24PC- |
1.3.6.1.4.1.9.1.1749 |
|
2960-Plus 24LC-L |
1.3.6.1.4.1.9.1.1750 |
|
2960-Plus 48PST-S |
1.3.6.1.4.1.9.1.1753 |
|
2960-Plus 24PC-S |
1.3.6.1.4.1.9.1.1754 |
|
2960-Plus 24LC-S |
1.3.6.1.4.1.9.1.1755 |
|
Catalyst 2960-S |
2960S Stack |
1.3.6.1.4.1.9.1.1208 |
2960S-24PD-L |
1.3.6.1.4.1.9.1.1261 |
|
2960S-24PS-L |
1.3.6.1.4.1.9.1.1265 |
|
2960S-48FPD-L |
1.3.6.1.4.1.9.1.1258 |
|
2960S-48FPS-L |
1.3.6.1.4.1.9.1.1263 |
|
2960S-48LPD-L |
1.3.6.1.4.1.9.1.1259 |
|
2960S-48LPS-L |
1.3.6.1.4.1.9.1.1264 |
|
Catalyst 2960L |
C2960L24TQLL |
1.3.6.1.4.1.9.1.2495 |
C2960L48TQLL |
1.3.6.1.4.1.9.1.2496 |
|
C2960L24PQLL |
1.3.6.1.4.1.9.1.2497 |
|
C2960L48PQLL |
1.3.6.1.4.1.9.1.2498 |
|
Catalyst 2960X |
Catalyst 2960X-48LPD-L |
1.3.6.1.4.1.9.1.1691 |
Catalyst 2960X-48TD-L |
1.3.6.1.4.1.9.1.1692 |
|
Catalyst 2960X-24TD-L |
1.3.6.1.4.1.9.1.1694 |
|
Catalyst 2960X-48FPS-L |
1.3.6.1.4.1.9.1.1695 |
|
Catalyst 2960X-48LPS-L |
1.3.6.1.4.1.9.1.1696 |
|
Catalyst 2960X-48TS-L |
1.3.6.1.4.1.9.1.1698 |
|
Catalyst 2960X-24TS-L |
1.3.6.1.4.1.9.1.1699 |
|
Catalyst 2960X-24PSK-L |
1.3.6.1.4.1.9.1.1700 |
|
Catalyst 2960X-48LPS-S |
1.3.6.1.4.1.9.1.1701 |
|
Catalyst 2960X-24PS-S |
1.3.6.1.4.1.9.1.1702 |
|
Catalyst 2960X-48TS-LL |
1.3.6.1.4.1.9.1.1703 |
|
Catalyst 2960X-24TS-LL |
1.3.6.1.4.1.9.1.1704 |
|
Catalyst 2960X-24PS-L |
1.3.6.1.4.1.9.1.1697 |
|
Catalyst 2960X-24PD-L |
1.3.6.1.4.1.9.1.1693 |
|
Catalyst 2960X-48FPD-L |
1.3.6.1.4.1.9.1.1690 |
|
Catalyst 2960XR |
Catalyst 2960XR-24PD-I |
1.3.6.1.4.1.9.1.1800 |
Catalyst 2960XR-24TD-I |
1.3.6.1.4.1.9.1.1801 |
|
Catalyst 2960XR-48FPS-I |
1.3.6.1.4.1.9.1.1802 |
|
Catalyst 2960XR-48LPS-I |
1.3.6.1.4.1.9.1.1803 |
|
Catalyst 2960XR-48TS-I |
1.3.6.1.4.1.9.1.1804 |
|
Catalyst 2960XR-24PS-I |
1.3.6.1.4.1.9.1.1805 |
|
Catalyst 2960XR-24TS-I |
1.3.6.1.4.1.9.1.1806 |
|
Catalyst 2960XR-48FPD-L |
1.3.6.1.4.1.9.1.1807 |
|
Catalyst 2960XR-48LPD-L |
1.3.6.1.4.1.9.1.1808 |
|
Catalyst 2960XR-48PD-L |
1.3.6.1.4.1.9.1.1809 |
|
Catalyst 2960XR-24PD-L |
1.3.6.1.4.1.9.1.1810 |
|
Catalyst 2960XR-24TD-L |
1.3.6.1.4.1.9.1.1811 |
|
Catalyst 2960XR-48FPS-L |
1.3.6.1.4.1.9.1.1812 |
|
Catalyst 2960XR-48LPS-L |
1.3.6.1.4.1.9.1.1813 |
|
Catalyst 2960XR-48TS-L |
1.3.6.1.4.1.9.1.1814 |
|
Catalyst 2960XR-24PS-L |
1.3.6.1.4.1.9.1.1815 |
|
Catalyst 2960XR-24TS-L |
1.3.6.1.4.1.9.1.1816 |
|
Catalyst 2960XR-48FPD-I |
1.3.6.1.4.1.9.1.1797 |
|
Catalyst 2960XR-48LPD-I |
1.3.6.1.4.1.9.1.1798 |
|
Catalyst 2960XR-48TD-I |
1.3.6.1.4.1.9.1.1799 |
|
Catalyst 2975 |
2975GS-48PS-L |
1.3.6.1.4.1.9.1.1067 |
2975GS-48PS-L-Stack |
1.3.6.1.4.1.9.1.1068 |
|
Catalyst 3550 |
3550-24-DC |
1.3.6.1.4.1.9.1.452 |
Catalyst 3560 |
3560-12PC-S |
1.3.6.1.4.1.9.1.1015 |
3560-24PS |
1.3.6.1.4.1.9.1.563 |
|
3560-24TS |
1.3.6.1.4.1.9.1.633 |
|
3560-48PS |
1.3.6.1.4.1.9.1.564 |
|
3560-48TS |
1.3.6.1.4.1.9.1.634 |
|
3560-8PC |
1.3.6.1.4.1.9.1.797 |
|
3560G-24PS |
1.3.6.1.4.1.9.1.614 |
|
3560G-24TS |
1.3.6.1.4.1.9.1.615 |
|
3560G-48PS |
1.3.6.1.4.1.9.1.616 |
|
3560G-48TS |
1.3.6.1.4.1.9.1.617 |
|
3560V2-24PS |
1.3.6.1.4.1.9.1.1021 |
|
3560V2-48PS |
1.3.6.1.4.1.9.1.1025 |
|
3560CX-12TC-S |
1.3.6.1.4.1.9.1. 2133 |
|
3560CX-8XPD-S |
1.3.6.1.4.1.9.1.2131 |
|
3560CX-8PT-S |
1.3.6.1.4.1.9.1.2130 |
|
Catalyst 3560-C |
3560CG-8PC-S |
1.3.6.1.4.1.9.1.1317 |
3560CPD-8PT-S |
1.3.6.1.4.1.9.1.1368 |
|
3560C-8PC-S |
1.3.6.1.4.1.9.1.1466 |
|
3560C-12PC-S |
1.3.6.1.4.1.9.1.1465 |
|
Catalyst 3560-E |
3560E-12D |
1.3.6.1.4.1.9.1.930 |
3560E-12SD |
1.3.6.1.4.1.9.1.956 |
|
3560E-24PD |
1.3.6.1.4.1.9.1.795 |
|
3560E-24TD |
1.3.6.1.4.1.9.1.793 |
|
3560E-48PD |
1.3.6.1.4.1.9.1.796 |
|
3560E-48TD |
1.3.6.1.4.1.9.1.794 |
|
Catalyst 3560-X |
3560X-24P (-L/S/E) |
1.3.6.1.4.1.9.1.1228 |
3560X-48PF (-L/S/E) |
1.3.6.1.4.1.9.1.1229 |
|
3560X-48P (-L/S/E) |
1.3.6.1.4.1.9.1.1229 |
|
3560X-48U |
1.3.6.1.4.1.9.1.1710 |
|
3560X-48TS |
1.3.6.1.4.1.9.1.2066 |
|
WS-C3560X-48T-S |
1.3.6.1.4.1.9.1.1227 |
|
Catalyst 3650 |
Catalyst C3650-24TS (-L/S/E) |
1.3.6.1.4.1.9.1.1823 |
Catalyst C3650-48TS (-L/S/E) |
1.3.6.1.4.1.9.1. 1824 |
|
Catalyst C3650-24PS (-L/S/E) |
1.3.6.1.4.1.9.1. 1825 |
|
Catalyst C3650-48PS (-L/S/E) |
1.3.6.1.4.1.9.1. 1826 |
|
Catalyst C3650-24TD (-L/S/E) |
1.3.6.1.4.1.9.1. 1827 |
|
Catalyst C3650-48TD (-L/S/E) |
1.3.6.1.4.1.9.1. 1828 |
|
Catalyst C3650-24PD (-L/S/E) |
1.3.6.1.4.1.9.1. 1829 |
|
Catalyst C3650-48PD (-L/S/E) |
1.3.6.1.4.1.9.1.1830 |
|
Catalyst C3650-Stack (-L/S/E) |
1.3.6.1.4.1.9.1.1830 |
|
Catalyst C3650-48PQ (-L/S/E) |
1.3.6.1.4.1.9.1.1881 |
|
Catalyst C3650-48TQ (-L/S/E) |
1.3.6.1.4.1.9.1.1882 |
|
Catalyst 3750 |
3750 Stack |
1.3.6.1.4.1.9.1.516 |
3750-24FS |
1.3.6.1.4.1.9.1.656 |
|
3750-24PS |
1.3.6.1.4.1.9.1.536 |
|
3750-24TS |
1.3.6.1.4.1.9.1.513 |
|
3750-48PS |
1.3.6.1.4.1.9.1.535 |
|
3750-48TS |
1.3.6.1.4.1.9.1.512 |
|
3750G-12S |
1.3.6.1.4.1.9.1.530 |
|
3750G-12S-SD |
1.3.6.1.4.1.9.1.688 |
|
3750G-16TD |
1.3.6.1.4.1.9.1.591 |
|
3750G-24PS |
1.3.6.1.4.1.9.1.602 |
|
3750G-24T |
1.3.6.1.4.1.9.1.514 |
|
3750G-24TS |
1.3.6.1.4.1.9.1.511 |
|
3750G-24TS-1U |
1.3.6.1.4.1.9.1.624 |
|
3750G-24WS-S25 |
1.3.6.1.4.1.9.1.778 |
|
3750G-24WS-S50 |
1.3.6.1.4.1.9.1.779 |
|
3750G-48PS |
1.3.6.1.4.1.9.1.603 |
|
3750G-48TS |
1.3.6.1.4.1.9.1.604 |
|
3750V2-24PS |
1.3.6.1.4.1.9.1.1023 |
|
3750V2-48PS |
1.3.6.1.4.1.9.1.1027 |
|
Catalyst 3750-X |
3750X-48P (-L/E) |
1.3.6.1.4.1.9.1.1225 |
3750X-48PF (-L/S/E) |
1.3.6.1.4.1.9.1.1225 |
|
3750X-48P (-L/S) |
1.3.6.1.4.1.9.1.1225 |
|
3750X-24P (-L/S/E) |
1.3.6.1.4.1.9.1.1224 |
|
Catalyst 3750 Metro |
3750-24TE-M |
1.3.6.1.4.1.9.1.574 |
Catalyst 3750-E |
3750E-24PD |
1.3.6.1.4.1.9.1.792 |
3750E-24TD |
1.3.6.1.4.1.9.1.789 |
|
3750E-48PD |
1.3.6.1.4.1.9.1.791 |
|
3750E-48TD-S |
1.3.6.1.4.1.9.1.790 |
|
Catalyst 3850 |
Catalyst C3850-24U (-L/S/E) |
1.3.6.1.4.1.9.1.1767 |
Catalyst C3850-48U (-L/S/E) |
1.3.6.1.4.1.9.1.1768 |
|
3850-48P (-L/S/E) |
1.3.6.1.4.1.9.1.1641 |
|
3850-24P (-L/S/E) |
1.3.6.1.4.1.9.1.1642 |
|
3850-48T (-L/S/E) |
1.3.6.1.4.1.9.1.1643 |
|
3850-24T (-L/S/E) |
1.3.6.1.4.1.9.1.1644 |
|
Catalyst 3850-12S-S |
1.3.6.1.4.1.9.1.1880 |
|
Catalyst 3850-12S-E |
1.3.6.1.4.1.9.1.1880 |
|
Catalyst 3850-24S-S |
1.3.6.1.4.1.9.1.1879 |
|
Catalyst 3850-24S-E |
1.3.6.1.4.1.9.1.1879 |
|
Catalyst C3850-12X48U |
1.3.6.1.4.1.9.1.1745 |
|
Catalyst 4500 |
4503 |
1.3.6.1.4.1.9.5.58 |
4503 |
1.3.6.1.4.1.9.1.503 |
|
4506 |
1.3.6.1.4.1.9.5.59 |
|
4506 |
1.3.6.1.4.1.9.1.502 |
|
4507 |
1.3.6.1.4.1.9.1.501 |
|
4510 |
1.3.6.1.4.1.9.1.537 |
|
Catalyst 4500-E |
4503-E |
1.3.6.1.4.1.9.1.874 |
4506-E |
1.3.6.1.4.1.9.1.875 |
|
4507R-E |
1.3.6.1.4.1.9.1.876 |
|
4510R-E |
1.3.6.1.4.1.9.1.877 |
|
4507R+E |
1.3.6.1.4.1.9.1.1286 |
|
4510R+E |
1.3.6.1.4.1.9.1.1287 |
|
Catalyst 4900 |
4948 |
1.3.6.1.4.1.9.1.626 |
4948-10GE |
1.3.6.1.4.1.9.1.659 |
|
Catalyst 6500 |
6503 |
1.3.6.1.4.1.9.5.56 |
6503 |
1.3.6.1.4.1.9.1.449 |
|
6504 |
1.3.6.1.4.1.9.1.657 |
|
6506 |
1.3.6.1.4.1.9.5.45 |
|
6506 |
1.3.6.1.4.1.9.1.282 |
|
6509 |
1.3.6.1.4.1.9.5.44 |
|
6509 |
1.3.6.1.4.1.9.1.283 |
|
6509-NEB |
1.3.6.1.4.1.9.5.61 |
|
6513 |
1.3.6.1.4.1.9.5.50 |
|
6513 |
1.3.6.1.4.1.9.1.400 |
|
Catalyst 6500-E |
6509-E |
1.3.6.1.4.1.9.1.283 |
6506-E |
1.3.6.1.4.1.9.1.282 |
|
6504-E |
1.3.6.1.4.1.9.1.657 |
|
6503-E |
1.3.6.1.4.1.9.1.449 |
|
Catalyst 6800ia |
Catalyst 6800ia-48FPD-L |
1.3.6.1.4.1.9.1.1866 |
Catalyst 6800ia-48TD-L |
1.3.6.1.4.1.9.1.1867 |
|
Catalyst 68xx |
Catalyst 68xx Virtual Switch |
1.3.6.1.4.1.9.1.1934 |
Catalyst 6880-X |
Catalyst 6880-XLE |
1.3.6.1.4.1.9.1.1784 |
Catalyst 6807-XL |
Catalyst 6807-XL |
1.3.6.1.4.1.9.1.1765 |
Catalyst 9200 |
C9200-24T |
1.3.6.1.4.1.9.1.2694 |
C9200-24P |
1.3.6.1.4.1.9.1.2694 |
|
C9200-48T |
1.3.6.1.4.1.9.1.2694 |
|
C9200-48P |
1.3.6.1.4.1.9.1.2694 |
|
C9200CX-12P-2XGH |
1.3.6.1.4.1.9.1.3164 |
|
C9200CX-8PT-2G |
1.3.6.1.4.1.9.1.3098 |
|
C9200CX-8UXG-2X |
1.3.6.1.4.1.9.1.3099 |
|
C9200CX-8P-2XGH |
1.3.6.1.4.1.9.1.3195 |
|
C9200CX-8UXG-2XH |
1.3.6.1.4.1.9.1.3196 |
|
Catalyst 9200L |
C9200L-24T-4G |
1.3.6.1.4.1.9.1.2695 |
C9200L-24P-4G |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-48T-4G |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-48P-4G |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-24T-4X |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-24P-4X |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-48T-4X |
1.3.6.1.4.1.9.1.2695 |
|
C9200L-48P-4X |
1.3.6.1.4.1.9.1.2695 |
|
Catalyst 9300 |
c9300 |
1.3.6.1.4.1.9.1.2494 |
c930024T |
1.3.6.1.4.1.9.1.2435 |
|
c930024P |
1.3.6.1.4.1.9.1.2436 |
|
c930024U |
1.3.6.1.4.1.9.1.2437 |
|
c930024X |
1.3.6.1.4.1.9.1.2438 |
|
c930048T |
1.3.6.1.4.1.9.1.2439 |
|
c930048P |
1.3.6.1.4.1.9.1.2440 |
|
c930048U |
1.3.6.1.4.1.9.1.2441 |
|
c930048UXM |
1.3.6.1.4.1.9.1.2442 |
|
Catalyst 9400 |
C9407R |
1.3.6.1.4.1.9.1.2500 |
C9410R |
1.3.6.1.4.1.9.1.2501 |
|
C9404R |
1.3.6.1.4.1.9.1.2499 |
|
Catalyst 9500 |
c950012Q |
1.3.6.1.4.1.9.1.2418 |
c950024Q |
1.3.6.1.4.1.9.1.2419 |
|
c950040X |
1.3.6.1.4.1.9.1.2420 |
|
Catalyst Express 500 |
500-24LC |
1.3.6.1.4.1.9.1.725 |
500-24PC |
1.3.6.1.4.1.9.1.726 |
|
500-24TT |
1.3.6.1.4.1.9.1.724 |
|
500G-12TC |
1.3.6.1.4.1.9.1.727 |
|
Catalyst Express 520 |
520-24LC |
1.3.6.1.4.1.9.1.933 |
520-24PC |
1.3.6.1.4.1.9.1.934 |
|
520-24TT |
1.3.6.1.4.1.9.1.932 |
|
520-8PC |
1.3.6.1.4.1.9.1.897 |
|
520G-24TC |
1.3.6.1.4.1.9.1.935 |
|
Cisco ME 4900 |
ME 4924-10GE |
1.3.6.1.4.1.9.1.788 |
Catalyst C6880x |
ciscoC6880x |
1.3.6.1.4.1.9.1.1936 |
Catalyst 3560CX |
Cisco Catalyst 3560CX-8XPD-S |
1.3.6.1.4.1.9.1.2131 |
Cisco Catalyst 3560CX-8PT-S |
1.3.6.1.4.1.9.1.2130 |
|
Catalyst C3560 |
catwsC3560CX12pdS |
1.3.6.1.4.1.9.1.2132 |
catwsC3560CX12pcS |
1.3.6.1.4.1.9.1.2134 |
|
catwsC3560CX8tcS |
1.3.6.1.4.1.9.1.2135 |
|
catwsC3560CX8pcS |
1.3.6.1.4.1.9.1.2136 |
|
Catalyst C2960 |
catwsC2960CX8tcL |
1.3.6.1.4.1.9.1.2137 |
Catalyst 2960CX |
Cisco Catalyst 2960CX-8PC-L |
1.3.6.1.4.1.9.1.2191 |
The following table lists the Meraki Switches and Meraki Managed Catalyst Switches that are supported for Switch Port based tracking through SNMP v2.
Series (Ethernet Ports Only) |
Supported Device |
System Object ID from CISCO-PRODUCTS-MIB or CISCO-STACK-MIB |
---|---|---|
Meraki MS210 |
MS210-24P |
1.3.6.1.4.1.29671.2.346 |
MS210-48LP |
1.3.6.1.4.1.29671.2.348 |
|
MS210-24 |
1.3.6.1.4.1.29671.2.345 |
|
MS210-48 |
1.3.6.1.4.1.29671.2.347 |
|
MS210-48FP |
1.3.6.1.4.1.29671.2.349 |
|
Meraki MS125 |
MerakiMS125-24 |
1.3.6.1.4.1.29671.2.371 |
MerakiMS125-24P |
1.3.6.1.4.1.29671.2.372 |
|
MerakiMS125-48 |
1.3.6.1.4.1.29671.2.373 |
|
MerakiMS125-48LP |
1.3.6.1.4.1.29671.2.374 |
|
MerakiMS125-48FP |
1.3.6.1.4.1.29671.2.375 |
|
Meraki MS220 |
MerakiMS220-8 |
1.3.6.1.4.1.29671.2.304 |
MerakiMS220-8p |
1.3.6.1.4.1.29671.2.305 |
|
MerakiMS220-24 |
1.3.6.1.4.1.29671.2.306 |
|
MerakiMS220-24p |
1.3.6.1.4.1.29671.2.307 |
|
MerakiMS220-48 |
1.3.6.1.4.1.29671.2.308 |
|
MerakiMS220-48lp |
1.3.6.1.4.1.29671.2.309 |
|
MerakiMS220-48fp |
1.3.6.1.4.1.29671.2.310 |
|
Meraki MS225 |
MS225-24 |
1.3.6.1.4.1.29671.2.328 |
MS225-24p |
1.3.6.1.4.1.29671.2.329 |
|
MS225-48 |
1.3.6.1.4.1.29671.2.330 |
|
MS225-48lp |
1.3.6.1.4.1.29671.2.331 |
|
MS225-48fp |
1.3.6.1.4.1.29671.2.332 |
|
Meraki MS250 |
MS250-24 |
1.3.6.1.4.1.29671.2.333 |
MS250-24p |
1.3.6.1.4.1.29671.2.334 |
|
MS250-48 |
1.3.6.1.4.1.29671.2.335 |
|
MS250-48lp |
1.3.6.1.4.1.29671.2.336 |
|
MS250-48fp |
1.3.6.1.4.1.29671.2.337 |
|
Meraki MS320 |
MS320-24 |
1.3.6.1.4.1.29671.2.311 |
MS320-24p |
1.3.6.1.4.1.29671.2.312 |
|
MS320-48 |
1.3.6.1.4.1.29671.2.313 |
|
MS320-48lp |
1.3.6.1.4.1.29671.2.314 |
|
MS320-48fp |
1.3.6.1.4.1.29671.2.315 |
|
Meraki MS350 |
MS350-24 |
1.3.6.1.4.1.29671.2.318 |
MS350-24p |
1.3.6.1.4.1.29671.2.319 |
|
MS350-48 |
1.3.6.1.4.1.29671.2.320 |
|
MS350-48lp |
1.3.6.1.4.1.29671.2.321 |
|
MS350-48fp |
1.3.6.1.4.1.29671.2.322 |
|
MS350-24x |
1.3.6.1.4.1.29671.2.327 |
Supported Cisco Routers
The following table lists the Cisco routers Emergency Responder supports.
Series (Ethernet Ports Only) |
Supported Device |
System Object ID from CISCO-PRODUCTS-MIB or CISCO-STACK-MIB |
---|---|---|
Cisco 1800 |
Cisco 1861-SRST-B/K9 |
1.3.6.1.4.1.9.1.904 |
Cisco 1861-SRST-C-B/K9 |
1.3.6.1.4.1.9.1.939 |
|
Cisco 1861-SRST-C-F/K9 |
1.3.6.1.4.1.9.1.940 |
|
Cisco 1861-SRST-F/K9 |
1.3.6.1.4.1.9.1.905 |
|
Cisco 1861-UC-2BRI-K9 |
1.3.6.1.4.1.9.1.902 |
|
Cisco 1861-UC-4FXO-K9 |
1.3.6.1.4.1.9.1.903 |
|
Cisco1861 |
1.3.6.1.4.1.9.1.1065 |
|
Cisco 1900 |
Cisco 1905 |
1.3.6.1.4.1.9.1.1192 |
Cisco 1921 |
1.3.6.1.4.1.9.1.1191 |
|
Cisco 1941 |
1.3.6.1.4.1.9.1.1047 |
|
Cisco 2800 |
Cisco 2811 |
1.3.6.1.4.1.9.1.576 |
Cisco 2821 |
1.3.6.1.4.1.9.1.577 |
|
Cisco 2851 |
1.3.6.1.4.1.9.1.578 |
|
Cisco 2900 |
Cisco 2911 |
1.3.6.1.4.1.9.1.1045 |
Cisco 2921 |
1.3.6.1.4.1.9.1.1044 |
|
Cisco 2951 |
1.3.6.1.4.1.9.1.1043 |
|
Cisco 3800 |
Cisco 3825 |
1.3.6.1.4.1.9.1.543 |
Cisco 3845 |
1.3.6.1.4.1.9.1.544 |
|
Cisco 3900 |
Cisco 3925 |
1.3.6.1.4.1.9.1.1042 |
Cisco 3925E |
1.3.6.1.4.1.9.1.1144 |
|
Cisco 3945 |
1.3.6.1.4.1.9.1.1041 |
|
Cisco 3945E |
1.3.6.1.4.1.9.1.1145 |
Supported Switch Modules and Network Modules
Emergency Responder supports the following switch modules and network modules.
Switch Modules and Network Modules |
System Object ID from CISCO-PRODUCTS-MIB |
---|---|
Cisco SM-ES2-16-P |
1.3.6.1.4.1.9.1.1048 |
Cisco SM-ES3-16-P |
1.3.6.1.4.1.9.1.1049 |
Cisco SM-ES3G-16-P |
1.3.6.1.4.1.9.1.1050 |
Cisco SM-ES2-24-P |
1.3.6.1.4.1.9.1.1052 |
Cisco SM-ES3-24-P |
1.3.6.1.4.1.9.1.1053 |
Cisco SM-ES3G-24-P |
1.3.6.1.4.1.9.1.1054 |
Cisco SM-D-ES3-48-P |
1.3.6.1.4.1.9.1.1056 |
Cisco SM-D-ES3G-48-P |
1.3.6.1.4.1.9.1.1057 |
NME-16ES-1G |
1.3.6.1.4.1.9.1.702 |
NME-16ES-1G-P |
1.3.6.1.4.1.9.1.663 |
NME-X-23ES-1G |
1.3.6.1.4.1.9.1.703 |
NME-X-23ES-1G-P |
1.3.6.1.4.1.9.1.664 |
NME-XD-24ES-2S-P |
1.3.6.1.4.1.9.1.665 |
NME-XD-48ES-2S-P |
1.3.6.1.4.1.9.1.666 |
Note |
Switch modules and network modules use the System Object IDs of the routers into which they are inserted. Support for ISR-G2 SM and NM requires installation of the Cisco Options Package (COP) file. Download the COP file from the Download Software page on Cisco.com |
Supported Cisco UCS Platforms
For information about supported Cisco Unified Computing System (UCS) platforms, see the Unified Communications Virtualization Supported Applications section of the Cisco Collaboration Virtualization wiki.
VMware Support
For information about VMware, see the Unified Communications VMWare Requirements section of the Cisco documentation wiki at https://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/uc_system/virtualization/virtualization-software-requirements.html.
Supported OVAs and Capacity
For information about OVAs, administrators should see the Virtualization for Cisco Emergency Responder (CER) at http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/uc_system/virtualization/virtualization-cisco-emergency-responder.html.
Related Documentation
Cisco Emergency Responder Documentation
See the publications for Cisco Emergency Responder. Navigate from the following documentation URL:
https://www.cisco.com/c/en/us/support/unified-communications/emergency-responder/series.html
Cisco Unified Communications Manager Documentation
See the Cisco Unified Communications Manager Documentation Guide and other publications specific to your Cisco Unified Communications Manager release. Navigate from the following URL:
Important Notes
Cisco Emergency Responder 12.5(x) Supported Upgrades
Cisco Emergency Responder 10.x and later is supported on Cisco Unified Computing System (UCS) and other virtual platforms only. All existing installations on Media Convergence Servers (MCS) should be migrated to UCS before upgrading to Cisco Emergency Responder 10.x or later.
Direct upgrades to Cisco Emergency Responder 12.5(x) are supported only for the following releases:
-
Cisco Emergency Responder 10.0(1) or Cisco Emergency Responder 10.0(2) or Cisco Emergency Responder 10.5(1) or Cisco Emergency Responder 10.5(1a)
-
Cisco Emergency Responder 11.0(1) till Cisco Emergency Responder 11.5(4) SU10
-
Cisco Emergency Responder 12.0(1) or Cisco Emergency Responder 12.0(1) SU1 or Cisco Emergency Responder 12.0(1) SU2
Direct upgrades from Cisco Emergency Responder 1.x, Cisco Emergency Responder 2.x, Cisco Emergency Responder 7.x, or Cisco Emergency Responder 8.0 or Cisco Emergency Responder 8.5 or Cisco Emergency Responder 8.6 or Cisco Emergency Responder 8.7 to Cisco Emergency Responder 12.5(x) are not supported. Customers must first complete an upgrade to Cisco Emergency Responder 8.6.
-
If existing Cisco Emergency Responder 1.x, Cisco Emergency Responder 2.x, Cisco Emergency Responder 7.x, or Cisco Emergency Responder 8.0 or Cisco Emergency Responder 8.5 or Cisco Emergency Responder 8.6 or Cisco Emergency Responder 8.7 is installed on an MCS model that is supported by Cisco Emergency Responder 8.6 or supported through Bridge Upgrade of the system, the customer must first upgrade to Cisco Emergency Responder 8.6, then migrate to UCS or virtual platform, and then upgrade to Cisco Emergency Responder 12.5(x).
-
If existing Cisco Emergency Responder 1.x, Cisco Emergency Responder 2.x, Cisco Emergency Responder 7.x, or Cisco Emergency Responder 8.0 or Cisco Emergency Responder 8.5 or Cisco Emergency Responder 8.6 or Cisco Emergency Responder 8.7 is installed on MCS, which is not supported by Cisco Emergency Responder 8.6, customer must perform a fresh installation of Cisco Emergency Responder 12.5(x).
COP Files Required for Upgrades to Release 12.5(x)
From | To | Upgrade Type | ||
---|---|---|---|---|
9.0(1) and 9.0(2) |
12.5.x |
Refresh upgrade. Required COP file:
|
||
10.0(1), 10.0(2), 10.5(1), and 10.5(1a) |
12.5.x |
Refresh upgrade. Required COP file:
|
||
11.0(1) |
12.5.x |
Refresh upgrade; no COP file required. |
||
11.5(1)— |
12.5.x |
Refresh upgrade; no COP file required. |
||
12.0(1), 12.0(1) SU(1), and 12.0(1) SU(2) |
12.5.x |
Refresh upgrade. Required COP file:
|
Caveats
This section contains information about accessing the Cisco Bug Search to find open caveats and resolved caveats.
Access Cisco Bug Search
Known problems (bugs) are graded according to severity level. These release notes contain descriptions of the following:
-
All severity level 1 or 2 bugs
-
Significant severity level 3 bugs
You can search for problems by using Cisco Bug Search.
Before you begin
To access Cisco Bug Search, you need the following items:
-
Internet connection
-
Web browser
-
Cisco.com user ID and password
Procedure
Step 1 |
To access Cisco Bug Search, go to: |
Step 2 |
Log in with your Cisco.com user ID and password. |
Step 3 |
To look for information about a specific problem, enter the bug ID number in the Search for field, then press Enter. |
Open Caveats
There are no known issues in this release.
Resolved Caveats
Identifier |
Headline |
---|---|
CER 12.5 unable to get files through SFTP from CLI |
|
Assigning to Smart Account through API is failing for CER Upgraded from 11.5 to 12.5 |
|
CER 12.5 CLI file list not displaying directories or files |
|
CER 12.5 - When restarting server restart sequence not saved on system-history.log |
|
Unable to add more than 6 IP addresses under CER SNMP V3 user |
|
CER ALI info in ERL shouldn't allow to configure spaces and more than 8 characters in zip code field |
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What'sNew in CiscoProduct Documentation, which also lists all new and revised Ciscotechnical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.