Displays information on configured Home Agent (HA) services.

all | name ha_name

all : Displays information on all Home Agent services.

name ha_name : Displays information for an existing HA service specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays all or a specific Home Agent-Security Parameters Index (HA-SPI) remote address list(s).

all | name ha_name

all : Displays information on all HA-SPI lists.

name ha_name : Displays information for an existing HA-SPI list specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information on the system hardware.

card [ card_num ]

Provides the hardware information for all ASR 5x00 cards or the card specified by card_num . card_num must be a value in the range 1 through 48 for the ASR 5000 or 1 through 20 for the ASR 5500 and must refer to an installed card.

inventory

Displays the ASR 5x00 hardware information for all slots in tabular format.

version [ board | diags | fans]

Displays the CPU information for all ASR 5x00 application cards and fan controller version for the upper and lower fan trays.

board : Only include the CPLD and FPGA version information.

diags : Only include the CFE diagnostics version information.

fans : Show the fan controller versions for the upper and lower fan trays.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Shows the output of the Redundant Array of Independent Disks (RAID) established on the ASR 5000 SMCs or ASR 5500 FSCs.

Displays Array Configuration Replicator (ACR) counter and statistical information.

all

Displays ACR information for all HD storage policies configured on the system.

counters [ all ] [ name name ] [ verbose ]

all : Displays ACR counter information for all HD storage policies configured on the system.

name name : Displays ACR counter information for an existing HD storage policy specified as an alphanumeric string of 0 through 63 characters.

statistics [ all ] [ name name ] [ verbose ]

all : Displays ACR statistical information for all HD storage policies configured on the system.

name name : Displays ACR statistical information for an existing HD storage policy specified as an alphanumeric string of 0 through 63 characters.

verbose

Displays HD storage statistics based on instance.

Important

In Release 20, 21.0 and 21.1, HeNBGW is not supported. This command must not be used for HeNBGW in these releases. For more information, contact your Cisco account representative.

This command displays Home evolved NodeB Gateway (HeNBGW) service related information.

henb-association [ all | full | henbgw-access-service henbgw_acc_svc_name | peer-address peer_ip_address | peer-id peer_id_value | summary ]

henb-association : Displays information about HENB associations.

all : Displays information for all HeNB associations.

full : Displays all available information for associated display or filter keyword (previous keyword).

henbgw-access-service : Displays information about HeNB associations with the specified HeNBGW access service.

henbgw_acc_svc_name is an alphanumeric string of 1 through 63 characters.

peer-address : Displays information about HeNB associations with the specified peer.

peer_ip_address is an IPv4 address in dotted-decimal notation or an IPv6 address in colon-separated-hexadecimal notation.

peer-id : Displays information about HeNB associations for the specified peer.

peer_id_value is an integer from 0 to 4294967295.

summary : Displays a summary of available information for the associated keyword (previous keyword).

session

Displays HeNBGW sessions.

all

Displays information for all HeNB sessions.

call-id call_id

call-id : Specifies a Call Identification Number. call_id is an eight-digit hexadecimal number.

full

Displays information on session state for matching sessions.

qci qci_value

call-id : Displays information for the HeNB associated with a specific QCI value. qci_value is an integer between 1 and 9.

s1-peer s1_peer_address

s1-peer : a specific S1 peer identified by the IP address of a peer eNodeB.

s1_peer_address is an IPv4 address in dotted-decimal notation or an IPv6 address in colon-separated-hexadecimal notation.

summary

This command displays summary information covering matching sessions.

ue

Displays UE information.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Important

In Release 20, 21.0 and 21.1, HeNBGW is not supported. This command must not be used for HeNBGW in these releases. For more information, contact your Cisco account representative.

This command displays HeNBGW Access service related information.

henb-association [ all | csg-id csg_id_value | full | henbgw-access-service henbgw_acc_svc_name | peer-address peer_ip_address | peer-id peer_id_value | summary | tai mcc mcc_val mnc mnc_val tac ] | name name

henb-association : Displays information about HeNB associations.

all : Displays information about all HeNBGW Access services.

csg-id : Displays information about HeNB associations for the specified CSG ID.

csg_id_value is an integer between 0 and 4294967295.

full : Displays all available information for associated display or filter keyword (previous keyword).

henbgw-access-service : Displays information about HeNB associations with the specified HeNBGW Access service.

henbgw_acc_svc_name is an alphanumeric string of 1 through 63 characters.

peer-address : Displays information about HeNB associations with the specified peer.

peer_ip_address is an IPv4 address in dotted-decimal notation or an IPv6 address in colon-separated-hexadecimal notation.

peer-id : Displays information about HeNB associations for the specified peer.

peer_id_value is an integer from 0 to 4294967295.

summary : Displays a summary of available information for associated display or filter keyword (previous keyword).

tai : Displays information about HeNB associations for the specified TAI.

mcc : Specifies a Mobile Country Code (MCC) as a three-digit number between 100 to 999.

mcc_val is MCC value. MCC values of 000-099 are Reserved codes.

mnc : Specifies the Mobile National Code (MNC).

mnc_val is MCC a two- or three-digit number between 00 to 999.

tac : Displays information about HeNB associations for the specified Type Allocation Code (TAC).

miscellaneous : Displays all available information for associated display or filter keyword (previous keyword).

name name statistics [ henbgw-access-service henbgw_acc_svc_name | miscellaneous [ verbose ] | peer-id peer_id_value s1ap [ cause | [ verbose ] ] | sctp [ buffer [ sessmgr sessmgr_value

name : Displays information for specific HeNBGW Access service name.

name : is an alphanumeric string of 1 through 63 characters.

statistics : Displays HeNBGW Access service statistics

miscellaneous : Displays Miscellaneous statistics.

s1ap : Displays S1AP statistics.

cause : Displays S1AP cause statistics.

sctp : Displays SCTP statistics.

buffer : Displays SCTP TX/RX buffer statistics.

sessmgr : Displays SCTP TX/RX buffer statistics on a specific sessmgr.

verbose : Specifies the verbosity.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Important

In Release 20, 21.0 and 21.1, HeNBGW is not supported. This command must not be used for HeNBGW in these releases. For more information, contact your Cisco account representative.

This command displays configuration for HeNBGW Network service.

henb-association [ all | csg-id csg_id_value | full | henbgw-access-service henbgw_acc_svc_name | peer-address peer_ip_address | peer-id peer_id_value | summary ] | name name

mme-association : Displays information about MME associations.

all : Displays all HeNBGW Network services.

full : Displays all available information for associated display or filter keyword (previous keyword).

henbgw-network-service : Displays information about HeNB associations with the specified HeNBGW Network service.

henbgw_net_svc_name is an alphanumeric string of 1 through 63 characters.

peer-address : Displays information about HeNB associations with the specified peer.

peer_ip_address is an IPv4 address in dotted-decimal notation or an IPv6 address in colon-separated-hexadecimal notation.

peer-id : Displays information about HeNB associations for the specified peer.

peer_id_value is an integer from 0 to 4294967295.

summary : Displays a summary of available information for the associated display or filter keyword (previous keyword).

name name statistics [ henbgw-network-service henbgw_net_svc_name | peer-id peer_id_value s1ap [ cause | [ verbose ] ] | sctp [ buffer [ henbgwmgr sessmgr_value

name : Displays information for specific HeNBGW Network service name.

name : is an alphanumeric string of 1 through 63 characters.

statistics : Displays statistics for specified object.

s1ap : Displays S1AP statistics.

cause : Displays S1AP cause statistics.

sctp : Displays SCTP statistics.

buffer Displays SCTP TX/RX buffer statistics.

henbgwmgr : Displays SCTP TX/RX buffer statistics on a specific henbgwmgr.

verbose : Specifies the verbosity.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

This command displays hexdump module related information.

file-space-usage

Displays information about the file space usage of hexdump records.

statistics

Displays information on various statistics related to hexdump records.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the white list of IMSI records in the Access Control database residing on Home NodeB Gateway (HNB-GW) service instances that control HNB and UE access to HNB-GW sessions.

hnbgw-service hnbgw_svc_name

Displays Access Control database records for an existing HNB-GW service specified as an alphanumeric string of 1 through 63 characters.

Note	This keyword is not supported in StarOS 14.0 and higher releases.

imsi imsi_value

Specifies the International Mobile Subscriber Identification (IMSI) number which is found on the Access Control database for he HNB-GW service.

imsi_value is an integer consisting of the 3-digit MCC (Mobile Country Code), the 2- or 3-digit MNC (Mobile Network Code) followed by the MSIN (Mobile Subscriber Identification Number). The total IMSI value must not exceed 15 digits.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the session counter information for Home-NodeB Gateway (HNB-GW) services connected on this system.

hnbgw-service hnbgw_svc_name

Filters the counter display based on an existing HNB-GW service name specified as an alphanumeric string of 1 through 63 characters.

hnbid hnb_identifier

Filters the counter display based on a Home-NodeB identifier specified as an alphanumeric string of 1 through 255 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the global configuration parameters for configured HNBGW service(s) on this system.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the active/dormant session information about registered HNB(s) on Home-NodeB Gateway (HNB-GW) service instances configured and running on this system based on different filter criteria.

full

Displays the full information for a specific registered HNB session(s) on an HNB-GW service instance running on the system. The display can be filtered based on given filtering criteria.

summary

Displays summarized information for a specific registered HNB session(s) on an HNB-GW service instance running on the system. The display can be filtered based on given filtering criteria.

all

Displays summarized information for all registered HNB sessions on an HNB-GW service instance running on the system. The display can be filtered based on given filtering criteria.

address hnb_ip_address

Filters the display of full or summarized session statistics to show only HNB session(s) based on the registered HNB IP address expressed in IPv4 dotted-decimal notation.

cell-id cell_id

Filters the display of full or summarized session statistics to show only HNB session(s) based on the registered Femto cell ID where the user/subscriber is geographically located. and must be an integer from 0 through 268435455.cell_id is an integer from 0 through 268435455.

hnb-access-mode {closed | open | hybrid }

Filters the display of full or summarized session statistics to show only HNB session(s) based on the HNB access mode in an HNB-GW service instance.

hnb-local-id hnb_id

Filters the display of full or summarized session statistics to show only HNB session(s) based on the registered local ID of HNB specified as an integer from 1 through 25.

hnbgw-service hnbgw_svc_name

Filters the display of session statistics to show only registered HNB session(s) based on an existing HNB-GW service name specified as an alphanumeric string of 1 through 63 characters.

This can be further filtered by using access-mode criteria: Closed, Hybrid, or Open.

hnbid hnb_glbl_id

Displays summarized or full information of HNB session(s) based on the registered global ID of HNB specified as an integer between 1 through 255.

mcc mcc

Displays summary information of HNB session(s) based on the registered Mobile Country Code (MCC) identification number of the UE specified as an integer between 101 through 999.

mnc mnc

Displays summarized or full information of HNB session(s) based on the registered Mobile Network Code (MCC) identification number of the UE specified as a 2- or 3-digit integer between 00 through 999.

lac lac

Displays summarized or full information for HNB session(s) based on the registered Location Area Code (LAC) identification number of the UE specified as an integer between 1 through 65535.

rac rac

Displays summarized or full information for HNB session(s) based on the registered Radio Access Code (RAC) identification number of the UE specified as an integer between 1 through 255.

rnc rnc

Displays summarized or full information for HNB session(s) based on the registered Radio Network Code (RAC) identification number of the HNB specified as an integer between 1 through 65535.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the session statistics for Home-NodeB Gateway (HNB-GW) services configured and running on this system.

gtpu-only

Displays Forwarded GTPU Pkt statistics for selected HNB/HNBGW Service.

hnb-access-mode { closed | hybrid | open }

Displays the session statistics of an existing HNB-GW service based on access mode filters. Other supported filters are:

hnbgw-service hnbgw_svc_name

Filters the display of session statistics for an existing HNB-GW service name specified as an alphanumeric string of 1 through 63 characters.

hnbap-only

Filters the display of session statistics to show only Home NodeB Application Part (HNBAP) traffic for the selected HNB-GW service which is configured and running on this system.

ipne-only

Filters the display of session statistics to show only IPNE for selected HNBGW Service which is configured and running on this system.

paging-only

Filters the display of Paging statistics for selected HNBGW Service.

ranap-only

Flitters the display of session statistics t to show only Radio Access Network Application Protocol (RANAP) traffic for the selected HNB-GW service which is configured and running on this system.

rua-only

Filters the display of session statistics to show only RANAP User Adaptation (RUA) traffic for the selected HNB-GW service which is configured and running on this system.

sccp-only

Filters the display of session statistics to show only Signaling Connection Control Part (SCCP) traffic for the selected HNB-GW service which is configured and running on this system.

sctp-only

Filters the display of session statistics to show only Stream Control Transmission Protocol (SCTP) traffic for selected HNB-GW service which is configured and running on this system.

verbose

Displays detailed statistics for all sessions on HNB-GW services or for a selected filtered and named HNB-GW service which is configured and running on this system.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the session statistics for Home-NodeB (HNB) connected to an HNB-GW service on this system.

hnbid hnb_identifier

Filters the display of session statistics based on an existing Home-NodeB identifier specified as an alphanumeric string of 1 through 255 characters.

hnbap-only

Filters the display of session statistics display to show only Home NodeB Application Part (HNBAP) traffic for the selected HNB which is connected to this system through HNB-GW service.

ranap-only

Filters the display of session statistics display to show only Radio Access Network Application Protocol (RANAP) traffic for the selected HNB which is connected to this system through HNB-GW service.

rua-only

Filters the display of session statistics display to show only RANAP User Adaptation (RUA) traffic for the selected HNB which is connected to this system through HNB-GW service.

verbose

Displays detailed statistics for all HNB sessions or for the selected filter and HNB which is connected to this system through HNB-GW service.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the configuration details for configured HNBGW service(s) on this system.

all

Displays configuration and other default parameters for all HNB-GW service configured on this system.

hnbgw-service hnbgw_svc_name

Displays configuration and default parameters for an existing HNB-GW service name specified as an alphanumeric string of 1 through 63 characters.

Displays information for HRPD Serving Gateway (HSGW) services on this system.

all

Displays configuration information for all HSGW services configured on this system.

name service_name

Displays configuration information for an existing HSGW service specified as an alphanumeric string of 1 through 63 characters.

statistics

Displays node-level statistics for the HSGW.

dns-stats

Displays information related to DNS P-GW selection for load balancing using DNS SRV lookup.

pcf-status

Displays information about the status of Packet Control Functions (PCFs) being monitored.

address IPv4_address

Displays status information for the specified PCF.

IPv4_address must be specified using IPv4 dotted-decimal notation.

filter { all | icmp-monitored | no-calls | summary | up }

Filters the PCF status information. Must be followed by the filter to be applied.

all : Shows all the PCFs.

icmp-monitored : Shows only PCFs which are ICMP monitored.

no-calls : Shows only PCFs which has no active sessions.

summary : Shows only a summary of the status of the PCFs.

up : Shows only PCFs which are alive.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays service, session, and statistics information for Home Subscriber Server (HSS) peer services configured on this system.

service { all | name name }

Displays HSS peer service statistics for HSS peer services configured on this system.

all : Displays HSS peer service statistics for all configured HSS peer services on this system.

name name : Displays HSS peer service statistics for an existing HSS peer service specified as an alphanumeric string of 1 through 63 characters.

session { all | callid id | full | mdn mdn | nai nai | summary }

Displays HSS peer service statistics for sessions on this system.

all : Displays HSS peer service statistics for all sessions on this system.

This keyword is also used to further filter the full and summary options.

callid id : Displays summarized or detailed statistics of HSS peer service sessions running and filtered on the basis of the call identifier specified as an 8-digit hexadecimal number.

This keyword is also used to further filter the full and summary options.

mdn mdn : Displays summarized or detailed statistics of MME sessions running and filtered on the basis of an existing Mobile Directory Number (MDN) expressed as an alphanumeric string of 1 through 100 characters.

This keyword is also used to further filter the full and summary options.

nai nai : Displays summarized or detailed statistics of MME-HSS sessions running and filtered on the basis of an existing Network Access Identifier (NAI) expressed as an alphanumeric string of 1 through 128 characters.

This keyword is also used to further filter the full and summary options.

summary : Displays a summarized output of session information. This keyword can be further filtered by adding the following options:

statistics { all | service name | summary }

Displays statistics for HSS peer services configured on this system.

all : Displays statistics for all HSS peer services configured on this system.

service name : Displays statistics for a an existing HSS peer service expressed as an alphanumeric string of 1 through 63 characters.

summary : Displays summarized statistics for all HSS peer services configured on this system.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in CLI Overview chapter of the Command Line Interface Reference.

Displays information for configured International Mobile Equipment Identity (IMEI) profiles.

all

Lists all IMEI profiles configured on the system.

full { all | name apn_name }

full : Instructs the system to display all information in the IMEI profile(s).

all : Displays a full set of information for all IMEI profiles configured on the system.

name imei_name : Displays a full set of information for a specific IMEI profile.

apn_name : Must be an existing IMEI profile expressed as an alphanumeric string of 1 through 64 characters.

name imei_name

Displays information for a specific IMEI profile expressed as an alphanumeric string of 1 through 64 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information and statistics specific to the policy control in IP Multimedia Subsystem (IMS) authorization service.

statistics

Displays the total collected statistics of all policy control parameters of IMS authorization service sessions since the last system restart or clear command.

service ims_auth_svc_name

Displays the total collected statistics of all IMS authorization sessions processed by a specific IMS authorization service since the last system restart or clear command. ims_auth_svc_name must be an existing IMS authorization service name, expressed as an alphanumeric string of 1 through 64 characters.

server { ip-address ip_address [ port port_value ] | name server_name }

Displays the server-level message statistics and the server IP address.

Specify the PCRF server name (1 through 64 alphanumeric characters), or server IP address in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the maximum backpressure information.

all

Displays the max-backpressure count among all active session manager instances.

facility sessmgr instance instance_number

Displays logged events for specific facility. That is, it will display the maximum backpressure count on that specific session manager instance.

instance_number must be an existing IMS authorization service name, expressed as an alphanumeric string of 0 to 10000000 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information of installed Policy Gates for specific subscriber in an IP Multimedia Subsystem (IMS) authorization (IMSA) service.

status [ summary | full ]

Displays the status of the installed policy gates and their flow definitions along with the run-time status in an IMS authorization service based on the specified criteria.

summary : Limits the display to a summary on the status of the installed policy gates and their flow definitions along with their run-time status in an IMS authorization service based on the specified criteria.

full : Displays the full information on status of the installed policy gates and their flow definitions along with their run-time status in an IMS authorization service based on the specified criteria.

counters all

Displays the counters/statistics of the installed policy gates and their flow definitions along with their run-time status in an IMS authorization service based on the specified criteria.

all displays all counters of the installed gates and their flow definitions along with their run-time status in an IMS authorization service based on the specified criteria.

imsi imsi_value [ nsapi nsapi_value ]

Displays all of the counters/status of the installed policy gates and their flow definitions along with the run-time status in an IMS authorization service based on the International Mobile Subscriber Identity (IMSI).

nsapi nsapi_value specifies the Network Service Access Point Identifier (NSAPI) and limits the display to a single PDP context of the subscriber.

callid call_id

Displays all of the counters/status of the installed policy gates and their flow definitions along with their run-time status in an IMS authorization service based on the call identifier.

ims-auth-service ims_auth_svc

Displays the status of the installed policy gates and their flow definitions along with their run-time status in the named IMS authorization service.

rulename rule_name

Displays all of the counters/status of the installed policy gates and their flow definitions along with their run-time status in an IMS authorization service based on the named dynamic charging rule.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

Please refer to the Regulating a Command's Output section of the Command Line Interface Reference for details on the usage of grep and more .

Displays information and statistics specific to the authorization servers used for IP Multimedia Subsystem (IMS) authorization (IMSA) service.

server [ ims-auth-service ims_auth_svc_name ]

Displays the information and statistics for all authorization servers configured within an IMS authorization service in a system.

ims-auth-service ims_auth_svc_name : Displays the configured authorization servers for IMS authorization within the named IMS authorization service.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

Please refer to the Regulating a Command's Output section of the Command Line Interface Reference for details on the usage of grep and more .

Displays information, configuration, and statistics of all/specific IP Multimedia Subsystem (IMS) authorization (IMSA) service.

all [ verbose ]

Displays information and configuration for all configured IMS authorization services with a single line of information for each IMS authorization service.

verbose : Displays all information and configuration data for all IMS authorization services configured on system.

name ims_auth_svc_name [ p-cscf { all | ip_address ipv4/ipv6_address

Displays the information, statistics, and configuration data for the named IMS authorization service. If the optional keyword is configured, this command displays the statistics information of all P-CSCF servers or specific server.

summary

Displays summarized information and configuration data for all IMS authorization services configured in a system.

statistics [ all | name ims_auth_svc_name ] [ verbose ]

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

Please refer to the Regulating a Command's Output section of the Command Line Interface Reference for details on the usage of grep and more .

Displays information, configuration, and statistics of sessions active in an IP Multimedia Subsystem (IMS) authorization (IMSA) service.

all

Displays information and configuration for all sessions running in IMS authorization services with a single line of information for each IMS authorization session.

apn apn_name

Displays all of the counters/status for the running services in an IMS authorization service based on the specified Access Point Name (APN).

callid call_id

Displays all of the counters/status for the running services in IMS authorization service based on the named call identifier.

facility sessmgr instance instance_no

Displays the IMS authorization sessions at the session manager instance level.

full

Displays complete information and configuration data for all sessions in IMS authorization services configured in a system.

ggsn-only

Displays GGSN-specific information in addition to detailed information about the session.

ims-auth-service ims_auth_svc_name

Displays the information, statistics, and configuration data for sessions in the named IMS authorization service.

imsi imsi_value [ nsapi nsapi_value ]

Displays all of the counters/status of the running services in an IMS authorization service based on the specified International Mobile Subscriber Identity (IMSI) and Network Service Access Point Identifier (NSAPI). The display is limited to a single PDP context of the subscriber.

ip-address ip_address

Displays all of the counters/status for the running services in IMS authorization service based on the specified host IP address.

local-sessions

Displays the IMS authorization sessions that are associated with local-policy.

remote-sessions

Displays the IMS authorization sessions that are associated with PCRF.

summary

Displays summarized information and configuration data for all IMS authorization services configured in a system.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

Please refer to the Regulating a Command's Output section of the Command Line Interface Reference for details on the usage of grep and more .

Displays the instance numbers for all currently enabled, facility-specific log instances.

facility facility_name

Specifies the facility for which instance-level logging has been enabled. facility_name can be aaamgr, hamgr or sessmgr.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays Unique Device Identifier (UDI) information for all hardware in the system for which a UDI is available.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays statistics for each rule in an access control group.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the information for all Access Control Lists (ACLs) or the named ACL. With no keyword supplied, a list of all access lists and their entries is displayed.

list_name

Specifies the name of an existing ACL configured in the current context as an alphanumeric string of 1 through 47 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the ARP table or the ARP information associated with the specified IP address.

ip_address

Specifies an IP address in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

| vrf vrf_name

Displays information for an existing VPN Routing and Forwarding (VRF) name expressed as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the contents of a Border Gateway Protocol (BGP) router Autonomous System (AS) path access list in the current context.

list_name

Specifies the name of an existing AS path access list configured in the current context as an alphanumeric string of 1 through 79 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays Border Gateway Protocol (BGP) information for the current context.

ip_address / mask

Specifies the IP address and netmask bits for the network for which information should be displayed. The IP address and mask is the number of subnet bits, representing a subnet mask in CIDR notation. These must be entered in the IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal CIDR notation.

debugging

Displays debug flags that are enabled.

filter-list list_name

Displays routes that match the specified filter list.

neighbors [ ip_address ]

Displays information for all neighbors or a neighbor specified as an IP address in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

route-map map_name

Displays routes that match the specified route-map.

summary

Displays summary BGP information.

| vpnv4 [ all [ ip_address / mask | neighbors | summary ] | route-distinguisher { ipv4_address | asn_value } rd_value | vrf vrf_name [ ip_address / mask | neighbors | summary ]

| vpnv6 [ all [ ipv4_ddress | neighbors | summary ] | route-distinguisher { ipv4_address | asn_value } rd_value | vrf vrf-name [ ip_address / mask | neighbors | summary ] ]

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the framed-prefixes along with session-id, vrf-name and pool-name. The command will also display the total number of framed-prefixes matching the filtering criteria.

sess-id session identifier

Displays framed-prefixes added by a specific session.

session_identifier must be an integer from 1 to 1152.

vrf vrf_identifier

Displays VRF specific routing information.

vrf_identifier must be an alphanumeric string of 1 through 63 characters.

Displays Internet Group Management Protocol (IGMP) information for all groups in a context or a specific IP address.

ip_address

Displays IGMP information for the IP address specified in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

all

Displays information for all IGMP groups associated with this context.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays statistical and configuration information for the IPv4-based interfaces, including a Virtual Routing and Forwarding (VRF) table for a specific context.

name intfc_name

Displays information for an existing interface specified as an alphanumeric string of 1 through 79 characters. If no interface name is specified, the information for all IP interfaces is displayed.

summary

Displays summarized information about requested IP interfaces.

tunnel [ gre-keepalive ]

Filters the IP interface information for GRE/IP-in-IP tunnel type interfaces.

gre-keepalive : Displays the keepalive information for a generic routing encapsulation (GRE) tunnel configured with this IP interface.

vrf vrf_name

Displays Virtual Routing and Forwarding (VRF) routing information for an existing VRF specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the names of IP pools that are enabled for the IP pool sharing protocol (IPSP) and lists the disposition of addresses in the pools.

summary

Displays only the disposition of the addresses in the participating IP pools. Does not show the names of the participating IP pools.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays host name to IP address mapping for current context. Must be followed by a specific IP host name.

hostname

Specifies a configured hostname as an alphanumeric string of 1 through 127 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays Open Shortest Path First (OSPF) routing information.

border-routers

Displays all known area border routers (ABRs) and autonomous system border routers (ASBRs) for OSPF.

database [ verbose ] [ ls-id ip_addr ] [ adv-router ip_addr ] [ ls-type { router | network | summary | asbr-summary | external | nssa | integer } ]

Displays a summary of the database information for OSPF.

verbose : Displays detailed OSPF database information.

ls-id ip_addr : Displays OSPF database information for the link state advertisements (LSAs) with the specified link state identifier (LSID). ip_addr is entered using IPv4 dotted-decimal notation.

adv-router ip_addr : Displays OSPF database information for the advertising router with the specified LSID. ip_addr is entered using IPv4 dotted-decimal notation.

ls-type { router | network | summary | asbr-summary | external | nssa | LSA_Numerical_Type } ] : Displays OSPF database information for the specified LSA type.

debugging

Lists which debugging parameters are enabled.

interface

Displays interface information for OSPF.

neighbor [ details ]

Displays summarized information about all known OSPF neighbors.

details : Displays detailed information about all known OSPF neighbors.

route [ summary ]

Displays the OSPF routing table.

summary : Displays the number of intra-area, inter-area, external-1 and external-2 routes.

virtual-links

Displays the OSPF virtual links.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for IP packet redirecting policy for Home Agent (HA).

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays statistics specific to IP pools.

address { pool-name pool_name | group-name group_name } { used | free | hold | release} [ limit limit ]

Displays IP pool addresses for the specified IP pool or pool group that are currently in the specified state.

pool-name pool_name : Displays IP addresses from an existing IP pool name specified as an alphanumeric string of 1 through 31 characters.

group-name group_name : Displays IP addresses from an existing IP pool group name specified as an alphanumeric string of 1 through 31 characters.

used : Displays the IP addresses that are in a used state.

free : Displays the IP addresses that are in a free state.

hold : Displays the IP addresses that are in a hold state.

release : Displays the IP addresses that are in a release state.

limit limit : Specifies the maximum number of address to display as an integer from 1 through 524287.

group-name group_name

Displays information about an existing IP pool group name specified as an alphanumeric string of 1 through 31 characters.

groups

Lists information about all IP pool groups.

hold-timer {imsi imsi | msid msid | username username [imsi imsi | msid msid ]}

Displays hold timer address information for the specified IMSI, MSID, or username.

imsi imsi : Displays hold-timer information for a valid IMSI (International Mobile Subscriber Identity), specified as a 15-character field that identifies the subscriber's home country and carrier.

msid msid : Displays hold-timer information for the MSID specified as a number from 7 through 16 digits.

username username : Displays hold-timer information for an existing username specified as an alphanumeric string of 1 through 127 characters.

Important

Active users cannot be displayed. If an active ID or username is entered, the following error message appears: Failure: No address matching the specified information was found! Please confirm that the options used match the network architecture/deployment, such as IMSI/MSID only, Username only, or IMSI/MSID plus Username. Please note that this command does not apply for addresses in the used state.

many-to-one

Lists information on Many-to-One NAT Realm IP address pools.

nat-realm

Lists information on NAT Realm IP address pools.

one-to-one

Lists information One-to-One NAT Realm IP address pools.

overlap

Lists information on overlapping IP pools.

pool-name pool_name

Displays information about an existing IP pool.

private

Displays information about IP pools marked Private.

public

Displays information about IP pools marked Public.

resource

Displays information about resource IP pools.

static

Displays information about static IP pools.

summary

Displays a summary of all IP pool information.

verbose

Displays detailed information about all IP pools.

wide

Displays detailed information formatted to more than 80 columns.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays IP prefix lists used to filter routes. With no keyword supplied, a list of all prefix lists and their entries is displayed.

detail

Displays detailed information for the named prefix list.

name

Displays information for the named prefix list.

summary

Displays summary information for the named prefix list.

list_name

Specifies the name of an existing prefix list as an alphanumeric string of 1 through 79 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related to currently configured static or VRF routes for the current context.

ip_address/mask

Specifies an IP address/mask (CIDR) for a static route in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

| vrf vrf_name

Displays information for an existing Virtual Routing and Forwarding (VRF) name expressed as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related to currently configured route-access-list used to filter routes.

name

Specifies the name of an existing route access list as an alphanumeric string of 1 through 79 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related to currently configured static routes.

ip_address/mask

Specifies an IP address/mask (CIDR) for a static route in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays configuration information for VPN Routing and Forwarding instances.

vrf_name

Specifies an existing VRF name as an alphanumeric string of 1 through 63 characters.

mpls-map-dscp-exp

Displays the MPLS mapping for the VRF.

Displays configuration information for VRF lists currently on the system.

list_name

Specifies the name of an existing VRF list as an alphanumerical string of 1 through 63 characters.

Displays the status of Intelligent Packet Monitoring System (IPMS) client service with information related to system and call events. It also displays the status of configured IPMS servers.

summary

Displays the summary of all configured IPMS client and IPMS servers.

all

Displays information for all configured IPMS client and IPMS servers.

server address ip_address

Displays status for the IPMS server specified as an IP address in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

Generates a list of the IP Network Enabler (IPNE) peers.

all

Generates a list of all peers bound to the IPNE services, including the local and peer addresses. Also displays the TCP connections for every Session Manager.

service ipne_service_name

Generates a list of the peers associated with the specified IPNE service.

Summary

Generates a summary of all available IPNE peer statistics.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays IP Service Gateway (IPSG) service information.

all

Displays information for all IPSG service(s) configured on the system.

name ipsg_service_name

Displays information for the specified IPSG service. ipsg_service_name must be an alphanumeric string of 1 through 63 characters.

counters

counters requires the output is to display counters associated with the IPSG service(s).

| { grep grep_options | more }

Specifies to pipe (send) the output of this command to the specified command. You must specify a command to which the output of this command should be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays IP Service Gateway (IPSG) session information.

counters

Displays session counters for matching sessions.

full

Displays all available information for matching sessions.

summary

Displays a summary of available information for matching sessions.

all

Displays session information including call ID, NAI, and home address for all current IPSG sessions.

This is the default behavior for the show ipsg sessions command.

callid call_id

Displays session information for a current IPSG session based on the specified call ID.

call_id must be an 8-digit hexadecimal number.

ip-address ipv4_address

Displays session information for a specific IPSG session based on the subscriber IP address.

ipv4_address must be specified in IPv4 dotted-decimal notation.

msid msid_number

Displays session information for a current IPSG session based on the specified MSID.

msid_number must be an 8-digit hexadecimal number.

peer-address ipv4_address

Displays session information for a current IPSG session based on the IP address of the device sending the RADIUS accounting messages.

ipv4_address must be specified in IPv4 dotted-decimal notation.

username user_name

Displays session information for an IPSG session based on subscriber's user name.

user_name must be an alphanumeric string of 1 through 127 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays IP Services Gateway (IPSG) service statistics.

name ipsg_service_name

Displays cumulative statistics of all IPSG sessions processed by the specified service since the last system restart or clear command.

ipsg_service_name must be the name of an IPSG service, and must be an alphanumeric string of 1 through 63 characters.

peer-address ipv4_address

Displays cumulative statistics of all IPSG sessions associated with the specified IP address of the device sending the RADIUS accounting messages. The statistics displayed are from the last system restart or clear command.

ipv4_address must be specified in IPv4 dotted-decimal notation.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays statistics for each rule in all IPv6 access groups or a specified IPv6 access control group.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the information for all IPv6 Access Control Lists (ACLs) or the named ACL. With no keyword supplied, a list of all access lists and their entries is displayed.

list_name

Specifies the name of an existing ACL configured in the current context as an alphanumeric string of 1 through 47 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays statistical and configuration information for the IPv6-based interfaces, including a Virtual Routing and Forwarding (VRF) table for a specific context.

name intfc_name

Displays information for an existing interface specified as an alphanumeric string of 1 through 79 characters. If no interface name is specified, the information for all IPv6 interfaces is displayed.

statistics

Displays the session statistics of all ingress and egress packets processed through this IPv6 interface.

summary

Displays summarized information about requested IPv6 interfaces.

vrf vrf_name

Displays Virtual Routing and Forwarding (VRF) routing information for an existing VRF specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the neighbor table for all IPv6 addresses or a specified IPv6 address in the current context.

ipv6_address

Displays information for an existing IPv6 address specified in IPv6 colon-separated-hexadecimal notation. If no IPv6 address is specified, the information for all IPv6 addresses is displayed.

vrf vrf_name

Displays Virtual Routing and Forwarding (VRF) routing information for an existing VRF specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information regarding the configuration of the OSPFv3 Protocol on this system.

show ipv6 ospf database

show ipv6 ospf debugging

Displays OSPFv3 Debugging Flags.

show ipv6 ospf interface

Displays OSPFv3 Interfaces.

show ipv6 ospf neighbor [ details ]

Displays OSPFv3 neighbors with the option for full details.

show ipv6 ospf route [ summary ]

Displays OSPFv3 route information with the option for summarized information.

show ipv6 ospf virtual-links

Displays OSPFv3 virtual links.

verbose

Displays detailed information.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related IPv6 Pool configuration/state.

group-name group-name

Displays IP address pool information for an existing group-name specified as an alphanumeric string of 1 through 31 characters.

pool-name pool-name

Displays IPv6 address pool information for an existing pool name specified as an alphanumeric string of 1 through 31 characters.

summary

Displays summary information about all IP address pools; this is the default.

verbose

Displays detailed information about all IP address pools.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related to an IPv6 prefix list.

detail prefix-list-name

Displays detailed IP address information for an existing prefix-list specified as an alphanumeric string of 1 through 79 characters.

name prefix-list-name

Displays IP address information for an existing prefix-list specified as an alphanumeric string of 1 through 79 characters.

ip-address/mask

Specifies an IPv6 Network Address/Mask Bits combination in CIDR notation.

longer

Displays IP address prefix-list details in longer format.

match-first

Displays first matched IP address prefix-list details.

seq seq_value

Specifies the sequence number as an integer from 1 through 4294967295.

seq_value is the integer value between 1 through 4294967295.

summary prefix-list-name

Displays prefix-list summary for an existing prefix-list specified as an alphanumeric string of 1 through 79 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information related to specific route for current context.

ip-address/mask

Specifies an IP address entered using IPv6 colon-separated-hexadecimal and CIDR notation.

vrf vrf-name

Displays Virtual Routing and Forwarding (VRF) routing information for an existing VRF specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the route access list.

route-access-list

route-access-list is an alphanumeric string of 1 through 79 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for Iu-PS services in the current context. The Iu-PS interface links the radio network controller (RNC) with the packet switched core network.

all

Shows information for all configured IuPS services.

name srvc_name

Specifies an existing IuPS service as an alphanumeric string of 1 through 63 characters.

gtpu-table

Displays the configured GTPU database.

rnc all

Displays information for all configured RNCs.

rnc rnc_id

Specifies the identification number of an existing RNC configuration instance as an integer from 0 through 4095.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for Layer 2 Tunneling Protocol (L2TP) tunnels.

full

Displays all available information for the specified sessions.

summary

Displays a summary of available information for the specified sessions.

counters

Displays counters for the specified L2TP sessions.

all

Displays all current sessions.

callid id

Displays session information for the call ID. specified an 8-byte hexadecimal number. The output of the command show l2tp tunnels contains a field labeled Callid Hint which lists the call ID information to use with this command.

username name

Displays session information for an existing subscriber specified as an alphanumeric string of 1 through 127 characters. Wildcard characters $ and * are allowed.

msid ms_id

Displays session information for the MSID specified as 7 to 16 digits for an IMSI, MIN, or RMI. Wildcard characters $ and * are allowed.

lac-service service_name

Displays all L2TP sessions in the specified LAC service.

lns-service service_name

Displays all L2TP sessions in the specified LNS service.

pdsnclosedrp-service service_name

Displays all L2TP sessions in the specified Closed R-P service.

peer-address [ operator ] peer_address

Displays all L2TP sessions to the destination (peer LNS) specified as an IP address in IPv4 dotted-decimal notation.

In conjunction with sessions keyword, indicates a range of peers is to be displayed.

peer-address [ operator ] peer_address is specified using IPv4 dotted-decimal notation.

Displays statistics for all Layer 2 Tunneling Protocol (L2TP) tunnels and sessions.

lac-service service_name

Displays L2TP statistics for all tunnels and sessions in an existing L2TP Access Concentrator (LAC) service specified as an alphanumeric string of 1 through 63 characters.

lns-service service_name

Displays L2TP statistics for all tunnels and sessions in tan existing L2TP Network Server (LNS) service specified as an alphanumeric string of 1 through 63 characters.

pdsnclosedrp-service service_name

Displays L2TP statistics for all tunnels and sessions in an existing Closed R-P service specified as an alphanumeric string of 1 through 63 characters.

peer-address peer_address

Displays L2TP statistics for all tunnels and sessions to the destination (peer LNS) at the IP address specified in IPv4 dotted-decimal notation.

Displays information for Layer 2 Tunneling Protocol (L2TP) tunnels.

full

Displays all available information for the specified tunnels.

summary

Displays a summary of available information for the specified tunnels.

counters

Displays counters for the specified L2TP tunnels.

all

Displays all current tunnels.

callid id

Displays tunnel information for the call id specified as an 8-digit hexadecimal number. The output of the command show l2tp tunnels contains a field labeled Callid Hint which lists the call id information to use with this command.

username name

Displays tunnel information for an existing subscriber specified as an alphanumeric string of 1 through 127 characters. Wildcard characters $ and * are allowed.

msid ms_id

Displays tunnel information for the MSID specified as 7 to 16 digits for an IMSI, MIN, or RMI. Wildcard characters $ and * are allowed.

lac-service service_name

Displays all L2TP tunnels in the specified LAC service.

lns-service service_name

Displays all L2TP tunnels in the specified LNS service.

pdsnclosedrp-service service_name

Displays all L2TP tunnels in the specified Closed R-P service.

peer-address [ operator ] peer_address

Displays all L2TP tunnels to the destination (peer LNS) at the IP address specified in IPv4 dotted-decimal notation.

In conjunction with tunnels keyword, indicates a range of peers is to be displayed.

peer-address [ operator ]: Specifies a peer address using IPv4 dotted-decimal notation.

Displays the information for all L2TP Access Concentrator (LAC) services or for a particular LAC service.

all

Display information for all LAC services.

name service_name

Display information only for an existing LAC service specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Refer to the Lawful Intercept Configuration Guide for a full description of this command.

Refer to the Lawful Intercept Configuration Guide for a description of these statistics.

Displays all details about the Lightweight Directory Access Protocol (LDAP) subsystem.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the current status of the light emitting diodes (LEDs) for a specific card or all cards.

all | card_num

all : Displays the LED status for all cards.

card_num : Displays the LED status for the card specified by its slot number.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information about licensing as configured on this system.

all

Shows a superset of information that includes show status, show usage, show UDI, as well as the Smart Licensing agent version.

This keyword applies to Smart Licensing only.

enforcement { policy | status [ allowed | blocked ] [ feature | service ] }

Shows the enforcement policy applied to or current enforcement status of Smart Licenses. Status information can be filtered based on the licenses which are currently allowed or blocked, or by license type.

allowed : displays the current status, and if out of compliance (OOC) the list of services which are blocked.

blocked : displays the list of services and features which are blocked.

feature : displays the current status, and if out of compliance (OOC) the list of services which are blocked.

service : displays the current status and if out of compliance (OOC) the list of services and features which are blocked.

This keyword applies to Smart Licensing only.

eval-period

Shows information about the evaluation period. Licenses are granted a 90 day evaluation period until they are registered.

This keyword applies to Smart Licensing only.

history

Displays the history of installed license and how much time each license was in each state. This keyword applies to legacy licensing only.

information [ key key_name ] [ full ]

Displays the license information to verify the proper keys have been installed. This command is also helpful in troubleshooting user system access due to the maximum number of sessions being reached.

key key_name : Displays the information for an existing license key specified as an alphanumeric string of 1 of 1 through 500 characters.

full : Displays the full features and quantities without any hardware limits in place.

key

Displays the installed keys in encrypted format.

privilege-bits

Displays all the CLI privilege bits that are turned on. This keyword applies for legacy licensing only.

smart-tags [ feature | service ]

Shows the features and services that are currently supported and the corresponding Smart Entitlement Tags.

feature : filters the output to show only features.

service : filters the output to show only services.

This keyword applies to Smart Licensing only.

statistics [ verbose ]

Shows Smart Licensing details for each individual feature. Use the optional verbose keyword to display additional information.

status

Shows information about the current state of Smart Licensing on the system, such as registration and license authorization status.

summary

Shows information about the current state of Smart Licensing on the system, such as registration, license authorization, and license usage status.

tech-support

Shows information useful for debugging issues with Smart Licensing.

udi

Shows details for all Unique Device Identifiers (UDI). This keyword applies to Smart Licensing only.

usage

Shows the usage information for all entitlements that are currently in use. This keyword applies to Smart Licensing only.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information about any Link Aggregation Group (LAG) configured in this system. A LAG works by exchanging control packets via Link Aggregation Control Protocol (LACP) over configured physical ports with peers to reach agreement on an aggregation of links. The LAG sends and receives the control packets directly on physical ports.

{ info | lacp info | statistics }

group group_number

Specifies the LAG number as an integer from 1 through 1023.

table [all] group_number

Displays information about the current LAG port configuration in tabular form. The all option includes ATM PVCs for ATM ports (ASR 5000 only).

utilization table

Displays LAG utilization data in tabular form.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays statistics for the link manager (linkmgr).

all

Display statistics for all link managers.

instance instance

Display statistics for a single instance of a link manager specified as an integer from 1 to 4.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays traffic statistics for the GPRS logical link-control (LLC) layer.

gprs-service srvc_name

Displays the statistics for an existing GPRS service specified as an alphanumeric string of 1 through 63 characters.

verbose

Displays all possible statistics for specified command or keyword.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For more information on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Reference.

Displays status information for the GPRS logical link-control (LLC) layer.

gprs-service srvc_name

Displays the LLC layer status for an existing GPRS service specified as an alphanumeric string of 1 through 63 characters.

sessmgr instance instance

Displays the LLC status for a session manager instance specified as an integer. The range varies depending upon the release:

dlci ms-id ms_id [ sapi sapid ]

Displays the LLC status for a specific data link connection identifier (DLCI) between the LLC and the mobile station (MS). ms_id must be an integer from 0 to 65536 that identifies the DLCI interface connecting to a specific MS.

sapi : Filters the display of the LLC status information to focus on a specific service access point interface (SAPI) within the specified DLCI specified as.an integer from 1 to 11

lsap sapid

Refines the display of the LLC status to focus on a specific lower service access point interface (LSAP) specified as an integer from 0 to 65536.

ms-id ms_id

Displays the LLC status for a connected MS specified as an integer from 0 to 65536.

usap sapid

Refines the display of the LLC statistics to focus on a specific upper service access point interface (USAP) specified as an integer from 0 to 65536.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For more information on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Reference.

Displays statistic and counter information for Local Mobility Anchor (LMA) services on this system.

all

Displays information about all configured LMA services on this system.

name service_name

Displays configuration information for an existing LMA service specified as an alphanumeric string of 1 through 63 characters.

session [ all | callid id | counters | full | ipv6-address { < address | > address | address | greater-than address [ less-than address ] | less-than address [ greater-than address ] } | summary | username name ]

Displays session information filtered by the following parameters:

all : Displays all active LMA sessions using LMA services on the system.

callid id : Displays available session information for the call identification number specified as an eight-byte hexadecimal number.