Displays statistic and counter information for Mobile Access Gateway (MAG) services on this system.

all

Displays information for all configured MAG services on this system.

name service_name

Displays configuration information for a specific MAG service configured on this system.

service_name must be an existing MAG service expressed as an alphanumeric string of 1 through 63 characters.

session [ all | callid id | counters | full | ip-address home_ip_address | msid id | summary | username name ]

all : Displays all active MAG sessions using MAG services on the system.

callid id : Displays available session information for the specific call identification number.

id must be an 8-digit hexadecimal number.

Refer to the keyword descriptions in this command for information regarding these filters.

Refer to the keyword descriptions in this command for information regarding these filters.

ip-address home_ip_address : Displays available session information for a specific home IPv4 or IPv6 address of a subscriber in a service session.

msid id : Displays available information for a specific mobile station identification number or group of numbers based on wildcard entry.

id must be a valid MSID number and can be a sequence of characters and/or wildcard characters ('$' and/or '*'). The * wildcard matches multiple characters and the $ wildcard matches a single character. If you do not want the wildcard characters interpreted as wildcard enclose them in single quotes ( '). For example: '$'.

summary : Displays the number of MAG sessions currently active for MAG services configured on the system.

username name : Displays available session information for a specific user in a service session.

name must be followed by an existing user name expressed as an alphanumeric string of 1 through 127 characters.

statistics [ name service_name ]

name service_name : Displays MAG service statistics for an existing MAG service specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information configured for the Mobile Application Part (MAP) services, including MAP service features and operational configuration. Also includes some related configuration information for the HLR and EIR configuration parameters.

name srvc_name

Specifies an existing MAP service as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays Mobile Application Part (MAP) statistics.

name srvc_name

Specifies an existing MAP service as an alphanumeric string of 1 through 63 characters.

recovered-values

Only displays recovered values for key KPI counters that were backed-up.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Shows the maximum temperature reached by each card since the last temperature timestamp reset.

verbose

Indicates that the output is to contain detailed information.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays configuration information for bearer services configured for the multimedia broadcast multicast service (MBMS) running on this system.

all

Displays information on all bearer services configured on the system.

apn apn_name mcast-addr ip_address

Displays bearer service information of the MBMS for a specific Access Point Name (APN). apn_name is bound to a given BM-SC (Broadcast Multicast - Service Center) server address ip_address .

apn_name is the name of the APN expressed as an alphanumeric string of 1 through 62 characters that is case sensitive.

ip_address is the IP address of the BM-SC server in IPv4 dotted-decimal notation bound to the APN.

full

Displays full information for specific or all instances of bearer service in MBMS feature on system.

instance instance_id

Displays session information filtered for an instance of a bearer service running as an MBMS session and specified an integer from 1 through 64.

service-type { broadcast | multicast }

Displays information for a specific type of service for MBMS.

broadcast : Specifies the MBMS service type as broadcast only.

multicast : Specifies the MBMS service type as multicast only.

sgsn-sessions

Displays summary information for all the SGSN multicast sessions.

summary

Displays summary information for specific or all instances of a bearer service.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more options, refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for specified Mobile IP Foreign Agent (MIP-FA) calls.

counters | full | summary

counters : Displayed output includes the statistical counters.

full : Displays detailed information.

summary : Displays only summary information. this is the default setting.

These options are not available in conjunction with the statistics keyword.

all | callid call_id | msid ms_id | peer-address peer_ip_address | reverse-tunnel { on | off } | username user_name

all : Displays all available information.

callid call_id : Displays information only for calls with the call ID specified as a 4-byte hexadecimal number.

msid ms_id : Displays information for a mobile subscriber ID expressed as a string from 7 to 16 digits for an IMSI, MIN, or RMI and/or characters $ and * for wildcard filter.

show mipha msid 01234567$$

Shows any subscriber with an MSID that matches the upper 8 digits of the supplied MSID, such as 01234567, and any two digits at the remaining two places.

peer-address peer_ip_address : Displays information for the MIP call for the peer IP address specified using IPv4 dotted-decimal notation.

reverse-tunnel { on | off }: Enables the display of reverse IP tunnel information.

username user_name : Displays MIP call user information for the username specified as an alphanumeric string of 1 through 127 characters that may include wildcard characters ($ and *).

statistics [ fa-service fa_name | peer-address [ peer_address | greater-than peer_address | less-than peer_address | > peer_address | < peer_address ]

Displays information for the foreign agent service specified by name or peer IP address.

fa-service fa_name must be an alphanumeric string of 1 through 63 characters.

peer-address peer_address must be specified using IPv4 dotted-decimal notation.

greater-than peer_address : Specifies the range of IPv4 addresses greater than peer_address.

less-than peer_address : Specifies the range of IPv4 addresses less than peer_address.

> peer_address : Specifies the range of IPv4 addresses greater than peer_address.

< peer_address : Specifies the range of IPv4 addresses less than peer_address.

peer-address [ operator ] peer_address

In conjunction with the mipfa [ summary ] peer-address keyword, indicates a range of peers is to be displayed.

peer-address [ operator ] peer_address must be specified using IPv4 dotted-decimal notation.

peers fa-service service_name [ current-sessions { { > | greater-than } sessions [ < sessions ] | { < | less-than } sessions [ > sessions ] | sessions } ] [ peer-address address ]

Displays peer servers for the specified FA service.

fa-service service_name : Specifies the name of an existing FA service for which the associated peer servers are to be displayed as an alphanumeric string of 1 through 63 characters.

peer-address address : Displays only peer servers matching the IP address entered in this parameter. address must be specified using IPv4 dotted-decimal notation and can be followed by the netmask of the address.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for specified Mobile IP Home Agent (MIP-HA) calls.

counters | full | summary

Default: concise output.

counters : Displayed output includes the statistical counters.

full : Displays detailed information.

summary : Displays only summary information.

These options are not available in conjunction with the statistics keyword.

msid msid_num

Displays information for the subscriber with the supplied MSID on HA.

msid msid_num specifies a mobile subscriber ID for which information is to be displayed. ms_id must be from 7 to 16 digits for an IMSI, MIN, or RMI and /or characters $ and * for wildcard filtering.

If enforce imsi-min equivalence is enabled on the chassis and MIN or IMSI numbers are supplied, this keyword/ filter will show subscribers with a corresponding MSID (MIN or IMSI) whose lower 10 digits matches the lower 10 digits of the supplied MSID.

show mipha msid ABCD0123456789 or

show mipha msid 0123456789

Shows any subscriber with a MSID that match the lower 10 digits of MSID supplied, such as 0123456789.

show mipha msid 01234567$$

Shows any subscriber with a MSID that match the upper 8 digits of the supplied MSID, such as 01234567 and any two digits at the remaining two places.

all | callid call_id | imsi imsi_num | ip-address ip_addr | msid msid_num | peer-address [ operator ] peer_address | reverse-tunnel { on | off } | username user_name

all : Displays all available information.

callid call_id : Displays information only for calls with the call ID specified as a 4-byte hexadecimal number.

imsi imsi_num : Specifies an IMSI (international mobile subscriber ID) for which information is to be displayed. The IMSI is a 15-character field which identifies the subscriber's home country and carrier.

ip-address ip_addr : Displays statistics for a call with the IP address specified in IPv4 dotted-decimal notation.

msid msid_num : Specifies a mobile subscriber ID only for which information is to be displayed. ms_id must be from 7 to 16 digits specified as an IMSI, MIN, or RMI.

peer-address peer_address : Displays statistical information for the peer IP address specified using IPv4 dotted-decimal notation.

reverse-tunnel { on | off }: Enables the display of reverse IP tunnel information.

username user_name : Displays user MIP call information for the username specified as an alphanumeric string of 1 through 127 characters including wildcard characters ($ and *).

peer-address [ operator ] peer_address

In conjunction with mipha [ summary ] peer-address keyword, indicates a range of peers is to be displayed.

peer_address must be specified using IPv4 dotted-decimal notation.

statistics [ ha-service ha_name | peer-address peer_address ]

Displays statistical information for the home agent service specified by its name (an alphanumeric string of 1 through 63 characters) or peer IP address (IPv4 notation).

peers ha-service service_name [ current-sessions { { > | greater-than } sessions [ < sessions ] | { < | less-than } sessions [ > sessions ] | sessions } ] [ peer-address address ]

Displays peer servers for the specified HA service.

ha-service service_name : Specifies the name of an existing HA service for which the associated peer servers are to be displayed as an alphanumeric string of 1 through 63 characters.

peer-address address : Displays only peer servers matching the IP address entered in this parameter. address must be specified using IPv4 dotted-decimal notation and can be followed by the netmask of the address.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays information for specified Mobile IPv6 Home Agent (MIPv6-HA) calls.

all

Displays all information for MIPv6-HA calls.

callid call_id

Specifies the Call Identification number as an 8-digit hexadecimal number.

counters [ all | callid | ipv6-address | username ]

full [ all | callid | ipv6-address | username ]

Displays all available information for the associated display or filter keyword.

ipv6-address ip_addr

statistics [ mipv6ha-service mipv6ha-service_name ]

Displays all information collected for specific protocol since last the restart or clear command.

This can be filtered according to a specified mipv6ha-service .

summary [ all | callid | ipv6-address | username ]

Displays summary information for defined sessions, based on defined parameters.

username user_name

Displays session information for a specific username.

Displays configuration information for MME-eMBMS services on this system. MME-eMBMS is the LTE version of Multimedia Broadcast/Multicast Service (eMBMS) on the Cisco Mobility Management Entity (MME).

mme_embms_service_name

Identifies the name of a specific MME-eMBMS service. The name comprises a string of 1 to 63 alphanumeric characters.

all

Lists all configured MME-eMBMS service instances on the system and displays upper-level service information for each of the services.

all-session-info [ summary ]

Lists all active eMBMS sessions currently being handled by the MMEmgr. Optionally, the display can provide a summary of eMBMS information for each session.

m3ap statistics { all [ verbose ] | name }

mce-association { all | full | name | path-info }

Displays peer MCE associations for either all eMBMS services or specifically for the named eMBMS service. Filters are included in the CLI to control the level of detail in the output.

When the mce-association and path-info keywords are used together, the output displays path informaiton for the MCEs associated with either all or only with the named MME-eMBMS service(s).

mce-session-association { plmn-id mcc mcc mnc mnc mce-id mce_id | tmgi-service-id tmgi_service_id mbms-flow-id mbms_flow_id }

name mme_embms_service_name [ summary ]

Displays the configuration for the named eMBMS service.

sctp statistics { all | name mme_embms_service_name }

Displays SCTP statistics for all or named “active” eMBMS service(s)

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays session information of Mobility Management Entity-Home Subscriber Server (MME-HSS) service(s) running on a peer or local system.

summary

This keyword displays the summarized output of this command.

full

This keyword displays detailed output of this command.

all

This keyword displays information of all MME-HSS sessions running on this system.

call-id call_identifier

Displays summarized or detailed statistics of MME-HSS sessions running and filtered by the call identifier with an MME-HSS service configured on this system.

call_identifier must an existing call identity in eight character Hex digit format running on an MME service on system.

mdn mdn_string

Displays summarized or detailed statistics of MME-HSS sessions running and filtered by mobile directory Number (MDN) with an MME-HSS service configured on this system.

mdn_string must be an alphanumeric string of 1 to100 characters.

nai nai_string

Displays summarized or detailed statistics of MME-HSS sessions running and filtered by Network Access Identifier (NAI) with an MME service configured on this system.

nai_string must be an alphanumeric string of 1 to128 characters.

verbose

This keyword displays the comprehensive information of specific or set of arguments.

| { grep grep_options | more }

This argument searches the output of the root command and selects the lines matching one or more patterns/options. The types of patterns are controlled by the options specified with grep_options .

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in CLI Overview chapter of the Command Line Interface Reference.

Displays configuration information for Mobility Management Entity (MME) services on this system.

all

Displays configuration information for all MME services configured on this system.

name service_name

Displays configuration information for an existing MME service specified as an alphanumeric string of 1 through 63 characters.

offload statistics

Displays configuration information for the MME load rebalancing feature (UE offload), as well as current statistics about any active offloading processes.

This keyword option is only available in Release 14.0 and higher.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the Mobile Management Entity (MME) database records for MME sessions grouped in session instances on this system and filtered with IMSI or GUTI as criteria.

all

Displays all database records of a session instance used for MME service.

call-id call_id

Displays database records filtered by the call ID specified as an 8-digit hexadecimal number

guti plmn plmn_id group-id mme_grp_id code mme_code m-tmsi mtmsi_value

Displays database records filtered by the Globally Unique Temporary Identifier (GUTI). The GUTI is constructed from the GUMMEI and the M-TMSI.

The GUMMEI is constructed from the public land mobile network (PLMN) ID [MMC and MNC] and the MME Group ID (MMEGI). Within the MME, the mobile is identified by the M-TMSI.

A GUTI has: 1) a unique identity for the MME which allocated the GUTI; and 2) the unique identity of the UE within the MME that allocated the GUTI.

The MME Identifier (MMEI) is constructed from an MME Group ID (MMEGI) and an MME Code (MMEC).

imsi imsi_identifier

Displays database records filtered by International Mobile Subscriber Identity (IMSI).

imsi_identifier is a 15-character IMSI field which identifies the subscriber's home country and carrier. Wildcard characters $ and * are allowed. The * wildcard matches multiple characters and the $ wildcard matches a single character. If you do not want the wildcard characters interpreted as a wildcard enclose them in single quotes ( ' ). For example; '$'.

This command displays the Mobile Management Entity (MME) database statistics for all or specific MME sessions on this system.

instance smgr_instance

Displays MME database statistics for a specific instance of a session manager running the MME service.

smgr_instance is an instance ID specified as an integer from 0 through 4294967295. If an instance is not specified, summary statistics are displayed.

Displays configuration information for an eNodeB association within an MME service.

summary

Displays summarized output for this command.

full

Displays detailed output for this command.

wf1

Displays output in a tabular format.

path-info

Displays S1 path association information of eNodeBs associated with MME services on this system.

all

Displays information of all eNodeBs associated with MME services on this system.

enodeb-name enodeb_name

Displays information for the specified eNodeB associated with MME services on this system.

henbgw

Displays information for Home eNodeB Gateways (HeNB-GWs) associated with MME services on this system.

Important

In Release 20, 21.0 and 21.1, HeNBGW is not supported. This keyword must not be used for HeNBGW in these releases. For more information, contact your Cisco account representative.

ipsec

Displays information of all IPSec enabled eNodeBs associated with MME services on this system.

mme-service-name mme_svc_name

Displays summarized or detailed configuration information for eNodeBs associated with an existing MME service specified as an alphanumeric string of 1 through 63 characters.

peer-address peer_ip_address

Displays summarized or detailed configuration information of eNodeBs associated with an existing MME peer IP address configured with an MME service and expressed in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

peer-id peer_identifier

Displays summarized or detailed configuration information for eNodeBs associated with a an existing MME peer ID configured with an MME service and specified as an integer from 1 through 4294967295.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

This command displays the current number of MME-assigned and eNodeB-assigned S1AP session IDs.

id summary

Displays the current number of MME-assigned and eNodeB-assigned S1AP session IDs.

service-name name

Filters the output of the command by for an existing MME service name specified as an alphanumeric string of 1 through 63 characters.

peer-id id

Filters the output of the command by a MME peer identifier specified as an integer from 1 through 4294967295.

sessmgr instance

Filters the output of the command by the specified session manager instance as an integer from 1 through 4294967295.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays session information for Mobile Management Entity (MME) service(s) running on a peer or local system.

summary

Displays summarized output for this command.

full

Displays detailed output for this command.

counters

Displays all counters for related events and messages for an MME session running on a system.

all

Displays information for all MME sessions running on this system.

callid call_identifier

Displays summarized or detailed configuration information for an MME session filtered by a call identifier within an MME service configured on this system.

call_identifier must be an existing call identity in 8-digit hexadecimal format running in an MME service on this system.

imei imei_id

Displays summarized or detailed configuration information about MME sessions running and filtered by an International Mobile Equipment Identification (IMEI) number within an MME service configured on this system.

imei_id must be an existing IMEI in an existing MME service on the system. imei_id must contain an 8-digit TAC (Type Allocation Code) and a 6-digit SNR (Serial Number).

imsi imsi_id

Displays summarized or detailed configuration information about MME sessions running and filtered by an International Mobile Subscriber Identity (IMSI) number within an MME service configured on the system.

imsi_id must be an existing IMSI in an existing MME service on the system. imsi_id is a 15-character IMSI field which identifies the subscriber's home country and carrier.

Wildcard characters $ and * are allowed. The * wildcard matches multiple characters and the $ wildcard matches a single character. If you do not want the wildcard characters interpreted as a wildcard enclose them in single quotes ( ' ). For example; '$'.

ipsec

Displays information for all IPSec enabled sessions using MME services on the system.

mme-service service_name

Displays summarized or detailed configuration information about MME sessions running and filtered by an MME service name configured on the system.

service_name must be a configured MME service on the system, expressed as an alphanumeric string of 1 through 63 characters.

msisdn number

Displays summarized or detailed configuration information about MME sessions running and filtered by a Mobile Station International ISDN Number.

number must be a combination of the CC (Country Code) and National (significant) mobile number, not exceeding 15 digits.

pdn-address pdn_ip_address

Displays summarized or detailed configuration information about MME sessions running and filtered by the IP address of a connected PDN(s) within an MME service configured on this system.

pdn_ip_address must be a configured IP address of a PDN expressed in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation within an existing MME service on the system.

s1-peer s1_peer_ip_address

Displays summarized or detailed configuration information of MME sessions running and filtered by the IP address of a peer connected through an S1 interface within an MME service configured on this system.

s1_peer_ip_address must be a configured IP address of a peer on S1 interface expressed in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation within an existing MME service on this system.

s11-peer s11_peer_ip_address

Displays summarized or detailed configuration information of MME sessions running and filtered by IP address of a peer connected through S11 interface with an MME service configured on this system.

s11_peer_ip_address must be a configured IP address of a peer on S11 interface expressed in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation within an existing MME service on this system.

vlr-name vlr_name

Displays summarized or detailed configuration information of MME sessions running and filtered by Visitor Location Register (VLR) name.

vlr_name must be an alphanumeric string of 1 through 63 characters.

ue-ecm-state { connected | idle }

Displays summarized or detailed configuration information about MME sessions running and filtered by the UE's EPS Connected Management (ECM) state.

connected : Specifies that summarized or detailed configuration information about MME sessions is to be displayed based on the UE ECM state of "connected".

idle : Specifies that summarized or detailed configuration information about MME sessions is to be displayed based on the UE ECM state of "idle".

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

This command displays MME service statistics specified by various criteria.

dcnr

Displays the dual connectivity NR statistics.

decor [ decor-profile profile_name ]

Displays the Decor statistics for all the configured Decor profile(s).

decor-profile profile_name : Displays Decor statistics for the specified Decor profile. profile_name must be an alphanumeric string of 1 through 63 characters.

emm-only

Displays only EPS mobility management (EMM) related statistics, or filters EMM statistics for a specific MME service name or a specific eNodeB association peer identifier.

esm-only

Displays only EPS session management (ESM) related statistics, or filters ESM statistics for a specific MME service name or a specific eNodeB association peer identifier.

handover

Displays only handover related statistics (such as Intra-MME, EUTRAN<->EUTRAN via S10, EUTRAN<->UTRAN via GnGp, EUTRAN<->GERAN via GnGp, and EUTRAN<->UTRAN via S3), or filters handover statistics for a specific MME service name or a specific eNodeB association peer identifier.

mme-service mme_svc_name

Displays MME service statistics for only the specified MME service name.

paging-profile [ profile-name paging_profile_name ]

Displays the paging profile statistics for all the configured paging-profile(s) one after another.

profile-name paging_profile_name : Displays the paging profile statistics for the given profile name. paging_profile_name must be an alphanumeric string of 1 through 63 characters.

peer-id peer_identifier

Displays MME service statistics for only the specified eNodeB association peer identifier.

recovered-values

Enables the display of recovered counter values if the backup and recovery of statistics has been enabled. This keyword can be combined with the emm-only , the esm-only , or the peer-id options. For details on this feature, refer to the Backup and Recovery of Key KPI Statistics feature chapter in the MME Administration Guide.

s1ap

Displays only S1-AP related statistics, or filters S1-AP statistics for a specific MME service name or a specific eNodeB association peer identifier..

sctp

Displays only SCTP related statistics, or filters SCTP statistics for a specific MME service name or a specific eNodeB association peer identifier.

tai taidb db_name mcc mcc mnc mnc tac tac

Displays only TAI statistics stored for the specified TAI management database name and MCC/MNC/TAC .

db_name : Specifies the name of the TAI management database as an alphanumeric string of 1 through 64 characters.

mcc : specifies the mobile country code (MCC) portion of a PLMN identifier as an integer from 100 through 999.

mnc : specifies the mobile network code (MNC) portion of a PLMN identifier as a 2- or 3-digit integer from 00 through 999.

tac : specifies the Tracking Area Code portion of the TAI as an integer from 1 through 65535.

Important

For the MME to report TAI level statistics, you must first issue the MME Service Configuration Mode command: statistics collection-mode tai. Only those MME Services which are configured accordingly will provide TAI based statistics. When the collection-mode is configured to tai , the peer-id keyword will no longer report valid statistics (All values will be shown as ZERO).

Caution

Changing this collection mode will restart the MME service and will clear all statistics at the MME service and eNodeB level.

verbose

Displays comprehensive information for a specific argument or set of arguments.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the current status of the Version Priority List (VPL) for one or all plugin modules installed on the system. This command is associated with the dynamic software upgrade process.

plugin_name

Filters the output of the VPL by an existing plugin name expressed as an alphanumeric string of 1 through 16 characters.

Displays Multiprotocol Label Switching (MPLS) cross-connect information.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays MPLS FEC-to-NHLFE (FTN) table information.

vrf vrf_name

Displays FTN information for the Virtual Routing and Forwarding (VRF) specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays MPLS Incoming Label Map (ILM) table information.

fec

Displays Forwarding Equivalency Class (FEC) information.

label label_value

Displays MPLS ILM information for the specified label. label_value is an integer from 16 through 1048575.

verbose

Displays detailed information for the MPLS ILM table.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays MPLS Label Distribution Protocol (LDP) information.

bindings

Displays the MPLS LDP label bindings.

ldp-id

Displays label values for a specific peer LDP ID.

local

Displays locally assigned label values.

prefix

Displays label values for a specific prefix.

remote

Displays remotely assigned label values.

discovery

Displays the MPLS LDP discovery information.

neighbor

Displays the MPLS LDP peer information.

detail

Displays the MPLS LDP peer information in details. The displayed information includes, Local LDP ID, Peer LDP ID, Transport address, State (for example, Established), Role (for example, Active), Uptime, Keepalive negotiated hold time, Proposed Local/Peer, Remaining Keepalive hold time, and Address advertised.

Displays MPLS Next-Hop Label Forwarding Entry (NHLFE) table information.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays configuration and/or statistical information for MRME services on this system.

all

Displays all MRME services.

name name

Displays information for specific MRME service name.

name is a string of size 1 to 63 .

statistics

Displays Node level Statistics for MRME.

verbose

Specifies Detailed statistics.

dns-stats

Specifies the information related to theDNS selection of P-GW.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays configuration and statistical information of the data stored in the active session entry (if present) of the specified User Equipment's (UE) MAC address.

mac mac_address

Specifies the MAC address.

mac_address must be an alpha-numeric string of 1 to 15 characters and should not be separated by a colon or hyphen.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays configuration and statistical information of the IMSI to session manager mapping (if available) in the mapping table of the IPSG manager.

imsi imsi_value

Specifies the International Mobile Subscriber Identity (IMSI) value.

imsi_value must be an integer from 1 to 15 digits.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays configuration and statistical information of the User Equipment (UE) MAC address to IMSI mapping (if available) in the mapping table of the IPSG manager.

mac mac_address

Specifies the MAC address.

mac_address must be an alpha-numeric string of 1 to 15 characters and should not be separated by a colon or hyphen.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

This command is not supported in this release.

This command is not supported in this release.

Displays information for multicast sessions defined by the specified keywords.

command_keyword

The following keywords are base commands that each have a distinct display output. Only one keyword can entered on the command line.

debug-info { callid id | flowid id }

Displays internal call troubleshooting information for multicast sessions defined by the specified keywords.

callid id: Displays subscriber information for the call specified as an 8-digit hexadecimal number.

flowid id: Displays information for a specific BCMCS flow, defined by The flow ID as a hexadecimal number.

full

Displays all available multicast session information. The following filter keywords are valid for this command: active, all, callid, card-num, dormant, flowid, flowid-type, mcast-address, pcf, pdsn-service, grep, more

summary

Only displays a summary of multicast session information. The following commands are valid for this command: active, all, callid, card-num, dormant, flowid, flowid-type, mcast-address, pcf, pdsn-service, grep, more

filter_keywords

The following keywords are filters that modify or filter the output of the Command Keywords. Not all filters are available for all Command Keywords. Multiple Filter Keywords can be entered on a command line.

When multiple Filter Keywords are specified, the output conforms to all of the Filter Keywords specifications.

active

Only displays information for multicast sessions that are currently active.

all

If no keywords are specified before all , information for all multicast sessions is displayed. If keywords are specified before all , all information is displayed with no further options being allowed.

callid id

Displays multicast session information for the call specified by id. The call must be specified as an 8-digit hexadecimal number.

card-num card_num

The slot number of the processing card by which the subscriber session is processed. card_num is a slot number from 1 through 7 or 10 through 16 on the ASR 5000, or 1 through 4 or 7 through 10 on the ASR 5500.

dormant

Shows information for subscriber sessions that are dormant (not transmitting or receiving data).

flowid id

Displays information for a specific BCMCS flow, defined by id. The flow ID must be a hexadecimal number.

flowid-type [ flow | program ]

Displays information for multicast sessions according to the type of flow.

flow: Shows all multicast sessions for the flow ID type "flow".

program: Shows all multicast sessions for the flow ID type "program".

mcast-address ipv4_address

Show multicast sessions for a specific multicast address. Must be followed by the IP address of an interface, using IPv4 dotted-decimal notation.

pcf ipv4_address

Displays information for multicast sessions connected via the packet control function, defined by ipv4_address . The address must be specified using IPv4 dotted-decimal notation.

pdsn-service svc_name

Displays information for multicast session connected to the packet data service svc_name. The packet data service must have been previously configured and expressed as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

Please refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter for details on the usage of grep and more .

Displays information for the specified network-requested packet data protocol (PDP) context.

imsi imsi_value

Specifies that information will be displayed for a particular International Mobile Subscriber Identity (IMSI). imsi_value is an integer from 1 to 15 digits.

Displays information regarding the network service entities (NSEs) in the network.

consolidated-status

Displays Network Service Virtual Connection (NSVC) status information for all network service entities in the network. This keyword is particularly useful for troubleshooting.

fr-config [ peer-nsei nsei ]

Displays network service configurations for NSEs using Frame Relay configurations.

peer-nsei nsei limits the display to a specific peer NSE identified as an integer from 0 through 65535.

ip-config [ nsvl { all | instance value }

Displays network service configurations for NSEs using IP configurations.

Including the nsvl keyword limits the display to all or a single (instance 0 to 3) of a network service virtual link.

Displays an Address Resolution Protocol (ARP) for a specified VPN identifier.

identifier

Specifies a valid VPN identifier as an integer from 0 through 2114.

nexthop ip_address

Specifies a valid nexthop IP address in IPv4 dotted decimal or IPv6 colon-separated-hexadecimal notation.

slot slot_number

Specifies the slot number of the card for which the lookup is being form. slot is one of the following integers: 1, 2, 8 or 9.

Displays packet error counters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays queue status and performance statistics from the Traffic Manager (TM) component of an MIO NPU.

queue [ mode { both | hex | text } ]

Displays the TM queuing information for the specified NPU. The mode option allows you to specify hexadecimal, ASCII text or both types of display values.

statistics [ reset ]

Displays TM-related operational statistics. The reset option allows you to clear the statistical counters.

card/cpu/npu

Specifies the card slot (5 or 6), CPU number (0), and NPU number (1 through 4).

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays NPU utilization information.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the network timing protocol (NTP) associations and status.

associations

Displays the current NTP server associations and related statistics.

status

Displays the client permeates configured and the synchronization status.

address ip_address

Specifies the IP address of an NTP server/client in the current context in IPv4 dotted-decimal notation.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter.

Displays the configuration of network reachability servers for the current context.

all

Displays configuration information for all network reachability servers in the current context.

ipv4-only

Displays IPv4 Network Reachability Detection servers.

ipv6-only

Displays IPv6 Network Reachability Detection servers.

name server_name

Displays configuration information for an existing network reachability server specified as an alphanumeric string of 1 through 15 characters.

Displays the information configured for an operator policy.

all

Displays a list of all operator policies configured on the system.

full { all | name op_policy_name }

full :Displays a full set of available information for the specified operator policy (policies).

all : Displays a full set of available information for all operator policies configured on the system.

name op_policy_name : Displays a full set of available information for an existing operator policy specified as an alphanumeric string of 1 through 64 characters.

name op_policy_name

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays information and statistics for the Object Request Broker Element Manager (ORBEM) interface in the current context.

client { id client_name | table }

Indicates the Common Object Request Broker Architecture (CORBA) client information is to be displayed. The keyword table is used to output to the display information on all configured clients. The keyword id is used to specify a specific client for which information is to be displayed specified as client_name .

client_name must refer to an existing client which is found using the table keyword option.

event-notif-service filters

Displays information pertaining to filters configured for the ORB Notification Service.

Important

In 18.0 and later releases, this keyword is obsolete.

session { id session_name | table }

Indicates session information is to be displayed. The keyword table is used to output to the display information on all configured clients. The keyword id is used to specify a specific session for which information is to be displayed specified as session_name .

session_name must refer to an existing session which is found using the table keyword option.

status

Indicates that the ORBEM server status information is to be displayed.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the status of the on-going software patch installation.

Displays the statistical and configuration information of configured Policy and Charging Control- Application Function (PCC-AF) services configured in a context.

all

all : displays information for all configured PCC-AF services.

name pcc_af_svc_name

Displays information only for an existing PCC-AF service specified as an alphanumeric string of 1 through 79 characters

statistics

Displays the statistical information for a specific service or all PCC-AF services configured in a context.

summary

Displays the summarized output of this command.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the active/dormant session information about Policy and Charging Control- Application Function (PCC-AF) service instances configured and running on this system based on different filter criteria.

full

Displays the full information of specific registered IP Connectivity Access Network (IP-CAN) session(s) on a PCC-AF service instance running on system. Display can be filtered based on given filtering criteria.

summary

Displays summarized information for specific registered IP-CAN session(s) on a PCC-AF service instance running on system. Display can be filtered based on given filtering criteria.

all

Displays summarized or full information for all registered IP-CAN session(s) on a PCC-AF service instance running on system. Display can be filtered based on given filtering criteria.

apn apn_name

Displays information for PCC-AF service sessions connected via an existing APN at the Policy and Charging Enforcement Function (PCEF).

ip-address pcc_af_ip_address

Filters the display of full or summarized session statistics for IP-CAN session(s) based on the IP address of a registered PCC-AF server on a PCC-AF service instance.

pcc_af_ip_address is an IP address expressed in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

call-id call_id

Filters the display of full or summarized session statistics for IP-CAN session(s) based on the registered call ID on a PCC-AF service instance for the IP-CAN session subscriber in 8-digit hexadecimal format.

pcc-af-service pcc_af_svc_name

Filters the display of session statistics for a registered IP-CAN session(s) based on an existing PCC-AF service name specified as an alphanumeric string of 1 through 63 characters.

sipuri sip_uri

Displays summarized or full information for IP-CAN session(s) based on the SIP-URI on a PCC-AF service instance.

sip_uri is the Session Initiation Protocol (SIP) addressing schema to call another person. It resembles an e-mail address and is written in the SIP URI format as sip:x@y:Port format, where x = username and y = host (domain or IP)

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the statistical and configuration information of configured PCC-Policy services configured in a context.

all

all : displays information for all configured PCC-Policy services.

name pcc_plcy_svc_name

Displays information for an existing PCC-Policy service specified as an alphanumeric string of 1 through 79 characters.

statistics

Displays statistical information for a specific or all PCC-Policy services configured in a context.

summary

Displays summarized output for this command.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays active/dormant session information about PCC-Policy service instances configured and running on this system based on different filter criteria.

full

Displays full information for a specific registered IP Connectivity Access Network (IP-CAN) session(s) on a PCC-Policy service instance running on system. Display can be filtered based on given filtering criteria.

summary

Displays summarized information for a specific registered IP-CAN session(s) on a PCC-Policy service instance running on system. Display can be filtered based on given filtering criteria.

all

Displays summarized or full information for all registered IP-CAN session(s) on a PCC-Policy service instance running on system. Display can be filtered based on given filtering criteria.

apn apn_name

Displays information for PCC-Policy service sessions connected via an existing APN on the PCEF.

imsi imsi_id

Displays summarized or full information for IP-CAN session(s) based on the International Mobile Subscriber Identity (IMSI) of a subscriber in a PCC-Policy service instance.

imsi_id is the IMSI and must be a 15-character field which identifies the subscriber's home country and carrier.

ip-address pcc_pcef_ip_address

Filters the display of full or summarized session statistics for IP-CAN session(s) based on the IP address of the registered PCEF node specified in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

call-id call_id

Filters the display of full or summarized session statistics display for an IP-CAN session(s) based on the registered call ID in a PCC-Policy service instance.

call_id must be an existing call identifier in the IP-CAN session subscriber expressed in 8-digit hexadecimal format.

pcc-policy-service pcc_plcy_svc_name

Filters the display of session statistics for registered IP-CAN session(s) based on an existing PCC-Policy service name specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the configuration information for Policy and Charging Control (PCC) services configured in a context.

all

all : displays information for all configured PCC services.

service-name pcc_svc_name

Displays information for an existing PCC service specified as an alphanumeric string of 1 through 79 characters.

summary

Displays the summarized output of this command.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays active/dormant session information about Policy and Charging Control (PCC) service instances configured and running on this system based on different filter criteria.

full

Displays full information for a specific registered IP Connectivity Access Network (IP-CAN) session(s) in a PCC service instance running on system. Display can be filtered based on given filtering criteria.

summary

Displays summarized information for a specific registered IP-CAN session(s) in a PCC service instance running on system. Display can be filtered based on given filtering criteria.

all

Displays summarized or full information for all registered IP-CAN sessions on a PCC service instance running on system. Display can be filtered based on given filtering criteria.

emergency-only

Displays summarized or full information for all IP-CAN sessions on a PCC service instance running on system which are using emergency APN for emergency services. Display can be filtered based on given filtering criteria.

instance instance_id

Displays summarized or full information for an IP-CAN session(s) based on the PCC service instance identifier on an IPCF/PCRF node specified as an integer from 1 through 512.

service-name pcc_svc_name

Filters the display of session statistics display of registered IP-CAN session(s) based on an existing PCC service name specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the statistical information for Policy and Charging Control (PCC) services configured in a context.

all

Displays statistical information for all configured PCC services on a system.

service-name pcc_svc_name

Displays information for an existing PCC service specified as an alphanumeric string of 1 to 79 characters. It can be further filtered by the PCC profile name used in an IP-CAN session.

profile-name pcc_profile_name

Displays information for an existing PCC profile in an IP-CAN session.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays statistical and configuration information for a configured PCC Sp-Endpoint instance in a context.

all

Displays statistical information for all configured PCC Sp-Endpoint instances on a system.

name sp_endpt_name

Displays information for an existing PCC Sp-Endpoint instance specified as an alphanumeric string of 1 through 79 characters.

| {grep grep_options | more}

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

connection

Displays statistics for the configured connection values along with peer selection success and failures.

Displays statistical and configuration information for an Sp interface connection in a PCC Sp-Endpoint instance.

all

Displays statistical information for all configured PCC Sp-Endpoint instances on a system.

name sp_endpt_name

Displays information for an existing PCC Sp-Endpoint instance specified as an alphanumeric string of 1 through 79 characters. It can further be filtered with an Sp Endpoint peer (SSC/SPR) name used for the IP Connectivity Access Network (IP-CAN) session.

peer ssc_name

Displays information only for the PCC Sp-Endpoint instance within an existing Subscriber Service Controller/Subscriber Profile Repository (SSC/SPR) as a peer for an IP-CAN session.

ssc_name is the name of the SSC/SPR node used by the Sp Endpoint interface.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays configuration information about PDG services configured on the system.

all

Displays information for all configured Packet Data Gateway/Tunnel Termination Gateway (PDG/TTG) services.

name service_name

Displays information only for an existing PDG service specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays statistics for the Packet Data Gateway/Tunnel Termination Gateway (PDG/TTG) since the last restart or clear command. The output includes the number of each type of Extensible Authentication Protocol (EAP) messages.

name service_name

Displays statistics for an existing PDG service specified an alphanumeric string of 1 through 63 characters.

peer-address ipv4_address

Displays statistics for a specific subscriber with the WLAN IP address specified in IPv4 dotted-decimal notation.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays configuration information about Packet Data Interworking Function (PDIF) services configured on the system.

all [ counters ]

Displays configuration information and statistical counters for all PDIF services in the system.

name name [ counters ]

Displays configuration information and statistical counters for an existing PDIF service specified as an alphanumeric string of 1 through 63 characters.

statistics [ name name | peer-address address ]

name name : Displays service statistics for a an existing PDIF service specified as an alphanumeric string of 1 through 63 characters.

peer-address address : Displays service statistics for a peer server IP address specified in IPv4 dotted-decimal notation.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the current number of PDN connections for each of the Restoration-Priority-Level values received from AAA across S6b interface.

restoration-priority-level { priority_level | all }

Restoration priority associated with PDN connection.

priority_level : Restoration priority level must be an integer from 1 through 8.

In StarOS 21.0 and later, priority levels 1 through 16 are supported.

all : Displays the number of PDN connections associated with all restoration priorities.

Displays information for configured packet data services in the current context.

all | name pdsn_name

all : Displays information for all configured packet data services.

name pdsn_name : Displays information only for an existing PDSN service specified as an alphanumeric string of 1 through 79 characters.

pcf-status [ address ip_address | filter [ all | icmp-monitored | no-calls | summary | up ] ]

pcf-status : Displays summary information for all Packet Control Functions (PCFs).

address ip_address: Only lists information for the PCF with the IP address specified in IPv4 dotted-decimal notation.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays information on configured Closed R-P services for the current context.

all | name name

all : Displays information for all configured Closed R-P services.

name name : Displays information for an existing Closed R-P service specified as an alphanumeric string of 1 through 79 characters.

Displays configuration of the specified peer profile.

all

Displays a list of all peer profiles configured on the system, arranged by service type.

full { all | name profile_name }

Displays detailed peer profile configuration information.

all : Displays detailed configuration information for all peer profiles configured on the system.

name profile_name : Displays detailed configuration information for the specified peer profile.

profile_name is an alphanumeric string of 1 through 64 characters.

name profile_name

Lists the specified peer profile, and the service type to which it belongs.

profile_name is an alphanumeric string of 1 through 64 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays configuration information for PDN Gateway (P-GW) services on this system.

all

Displays configuration information for all P-GW services configured on this system.

name service_name

Displays configuration information for an existing P-GW service specified as an alphanumeric string of 1 through 63 characters.

statistics { all | name service_name } [ verbose ]

Displays P-GW service statistics.

all : Displays statistics for all P-GW services on the system.

name service_name : Displays statistics for an existing P-GW service specified as an alphanumeric string of 1 through 63 characters.

If verbose is also specified, the information is displayed in more detail.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the current configuration of one or all plugin modules installed on the system. This command is associated with the dynamic software upgrade process.

plugin_name

Filters the output by an existing plugin name expressed as an alphanumeric string of 1 through 16 characters.

Displays information on configured parameters and operational statistics for physical and logical ports in the system.

datalink counters slot/port

Displays the physical layer information for all data links or only the one specified by the slot/port location of a previously configured port.

info [ slot/port ] [ vlan vlan_id ]

Displays detailed information for all ports within the chassis or only the one specified by slot/port location of a previously configured port.

vlan vlan_id : Displays detailed information about all Virtual Local Area Networks (VLANs) in the port/slot. If the optional vlan_id is not specified, this keyword displays port information for all VLANs in the slot/port location.

npu counters [ slot/port [ tagged | untagged | vlan tag_id ] ] | bound | unbound ]

Displays the information for Network Processing Unit (NPU) ports. The information for all ports is output or only the one specified by the slot/port location of a previously configured port.

For ASR 5500 MIO ports, this command displays the combined statistics for the specified port and its paired port (virtual pair).

tagged : Display statistics for all tagged packets.

untagged : Display statistics for all untagged packets.

vlan tag_id : Display NPU counters for a previously configured VLAN ID.

bound : Displays individual and cumulative NPU port counters for the bound ports within the current context. If the command is invoked in the local context, all of the bound ports for all contexts and cumulative counter values for all contexts are displayed.

unbound : Displays individual and cumulative NPU port counters for all unbound ports within system.

table

Displays information for all physical ports on rear-installed cards with physical interfaces.

transceiver slot/port

Displays diagnostic information for all SFP+ transceivers connected to a specified subscriber traffic port on the MIO card.

utilization table [ verbose ]

Shows average port utilization in Mbps. The output is a table that lists the current utilization average, a 5-minute average, and a 15-minute average, for all enabled ports.

The verbose option displays port utilization with kilobyte accuracy using decimal points.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

dinet

Displays the DI-network port statistics.

Displays information about the power on/off status of individual cards and the operating status of installed power filter units.

all | chassis | card_num ]

all : Displays power on/off state for all cards in the chassis.

chassis : Displays the operating status of installed power filter units. This is the default setting.

card_num : Displays the power on/off state for a single card specified an integer from 1 through 48 for the ASR 5000 or 1 through 20 for the ASR 5500.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays the point-to-point protocol (PPP) information, detailed or summarized, for one or all connections by the use of filtering options.

counters | full | summary

Filters the output for the level and type of information with the options described below.

counters : Displays PPP statistics.

full : Displays all available information.

summary : Displays only a summary of available information.

all | callid call_id | imsi imsi_id | msid ms_id | username user_name } ]

all : Displays all available information.

callid call_id : Displays PPP information only for the call ID specified as a 4-digit hexadecimal number.

imsi id : Displays PPP information only for the subscriber with the specified IMSI (International Mobile Subscriber Identity). id is a 15-digit field which identifies the subscriber's home country and carrier.

msid ms_id : Displays information for a mobile subscriber ID specified as 7 to 16 digits for an IMSI, MIN, or RMI.

username user_name : Displays user PPP information for the specified username.

statistics [ pcf-address [ pcf_ip_addr | all ] | pdsn-service pdsn_name ]

Displays statistics for all packet data services.

pcf-address [ pcf_ip_addr | all ]: Displays statistics only for the time the session is connected to the specified PCF (Packet Control Function) or for all PCFs. pcf_ip_addr must be specified using IPv4 dotted-decimal notation.

pdsn-service pdsn_name : Display statistics only for an existing PDSN service specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter in the Command Line Interface Reference.

Displays prepaid accounting information for all services or only the service specified.

all

Displays prepaid statistics for all services.

ggsn-service

Displays statistics for GGSN service(s).

ha-service

Displays statistics for HA service(s).

lns-service

Displays statistics for LNS service(s).

pdsn-service

Displays statistics for PDSN service(s).

pdsnclosedrp-service

Displays statistics for PDSN Closed-RP service(s).

{ all | name service_name }

all : Displays statistics for all services of the specified type.

name service_name : Displays statistics for an existing service specified an alphanumeric string of 1 through 63 characters.

per-service-summary

Displays prepaid statistics per service summary for all services.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section of the Command Line Interface Overview chapter in the Command Line Interface Reference.

This command displays prepaid WiMAX accounting information for all services or only the service specified.

all

This keyword displays prepaid statistics for all services.

asngw-service

Displays prepaid statistics for Access Service Network-Gateway (ASN-GW) service(s).

ha-service

Displays prepaid accounting statistics for Home Agent (HA) service(s).

{ all | name service_name }

all : Displays statistics for all services of the specified type.

name service_name : Displays statistics for an existing service specified as an alphanumeric string of 1 through 63 characters.

per-service-summary

Displays prepaid statistics per service summary for all services.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Displays information on process listings in the system.

card card_number

Displays the process listing for the specific card in the system.

cpu cpu_number

Displays the process listing for the specific card and CPU in the system.

Displays QoS Class Identifier-Radio Access Network (QCI-RAN) mapping tables configured on this system.

all

Displays information for all QCI-RAN mapping tables configured on this system.

name table_name

Displays information for an existing QCI-RAN table specified as an alphanumeric string of 1 through 63 characters.

| { grep grep_options | more }

Pipes (sends) the output of the command to the command specified. You must specify a command to which the output will be sent.

For details on the usage of grep and more , refer to the Regulating a Command's Output section in the Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays statistics for the Packet Switched (PS)-network(s) instance configured on a chassis for HNB-GW service sessions.

all

Displays status counters for all PS (packet switched) networks configured for HNB-GW service sessions on a chassis.

name ps_name

Displays status counters for a PS network configured for HNB-GW service specified as an alphanumeric string of 1 through 127 characters that is case sensitive

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

Refer to Regulating a Command's Output section of the Command Line Interface Overview chapter for details on the usage of grep and more .

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the session counter information for a PS Network associated with Home-NodeB Gateway (HNBGW) services configured and running on a system.

name ps_svc_name

Filters the counter display based on an existing HNB-PS Network service name associated with an HNB-GW service running on system. ps_svc_name is an alphanumeric string of 1 through 63 characters.

sgsn sgsn_point_code

Filters the counter display filtered on the basis of SGSN address provided in the SS7 point code that is connected to a particular HNB-PS Network service. sgsn_point_code must be the address of an SGSN in SS7 point code notation.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in Command Line Interface Overview chapter.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Displays the Packet Switched session statistics for Home-NodeB Gateway (HNB-GW) services configured and running on this system.

name ps_svc_name

Filters the session statistics display based on an existing HNB-PS Network service name that is associated with an HNB-GW service running on this system. ps_svc_name is an alphanumeric string of 1 through 63 characters.

sgsn sgsn_point_code

Filters the counter display filtered on the basis of SGSN address provided in the SS7 point code that is connected to a particular HNB-PS Network service. sgsn_point_code must be the address of an SGSN in SS7 point code notation.

gtpu-only

Filters the session statistics to display only GTP-U traffic for the specified HNB-PS Network service which is configured and associated with an HNB-GW service running on this system.

ranap-only

Filters the session statistics to display only Radio Access Network Application Protocol (RANAP) traffic for an HNB-PS Network service which is configured and associated with an HNB-GW service running on this system.

sccp-only

Filters the session statistics to display only Signaling Connection Control Part (SCCP) traffic for the specified HNB-PS Network service which is configured and associated with an HNB-GW service running on this system.

| { grep grep_options | more }

Pipes (sends) the output of this command to the specified command. You must specify a command to which the output of this command will be sent.

For details on the usage of the grep and more commands, refer to the Regulating a Command's Output section in Command Line Interface Overview chapter of the Command Line Interface Reference.