Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.2.x

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book

Results

Updated:
March 31, 2020

Chapter: Wireless Auto-QoS

Wireless Auto-QoS

Information About Auto QoS

Wireless Auto QoS automates deployment of wireless QoS features. It has a set of predefined profiles which can be further modified by the customer to prioritize different traffic flows. Auto-QoS matches traffic and assigns each matched packet to qos-groups. This allows the output policy map to put specific qos-groups into specific queues, including into the priority queue.

AutoQoS Policy Configuration

Table 1. AutoQoS Policy Configuration

Mode

Client Ingress

Client Egress

BSSID Ingress

BSSID Egress

Port Ingress

Port Egress

Radio

Voice

N/A

N/A

P3

P4

N/A

P7

ACM on

Guest

N/A

N/A

P5

P6

N/A

P7

Fastlane

N/A

N/A

N/A

N/A

N/A

P7

edca-parameters fastlane

Enterprise-avc

N/A

N/A

P1

P2

N/A

P7

P1

AutoQos-4.0-wlan-ET-SSID-Input-AVC-Policy

P2

AutoQos-4.0-wlan-ET-SSID-Output-Policy

P3

platinum-up

P4

platinum

P5

AutoQos-4.0-wlan-GT-SSID-Input-Policy

P6

AutoQos-4.0-wlan-GT-SSID-Output-Policy

P7

AutoQos-4.0-wlan-Port-Output-Policy

How to Configure Wireless AutoQoS

Configuring Wireless AutoQoS on Profile Policy

You can enable AutoQoS on a profile policy.

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Device# enable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

wireless autoqos policy-profile policy-name mode { enterprise-avc | fastlane | guest | voice}

Example:

Device# wireless autoqos policy-profile test-profile mode voice

Configures AutoQoS wireless policy.

  • enterprise-avc—Enables AutoQoS Wireless Enterprise AVC Policy.

  • fastlane—Enable AutoQoS Wireless Fastlane Policy.

  • guest—Enable AutoQoS Wireless Guest Policy.

  • voice—Enable AutoQoS Wireless Voice Policy.

Note

 

AutoQoS MIB attribute does not support full functionality with service policy. Service policy must be configured manually. Currently, there is only support for AutoQoS mode.

What to do next


Note

After enabling AutoQoS, we recommend that you wait for a few seconds for the policy to install and then try and modify the AutoQoS policy maps if required; or retry if the modification is rejected.

Disabling Wireless AutoQoS

To globally disable Wireless AutoQoS:

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Device# enable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

shutdown

Example:

Device# shutdown

Shuts down the policy profile.

Step 3

wireless autoqos disable

Example:

Device# wireless autoqos disable

Globally disables wireless AutoQoS.

Step 4

[no] shutdown

Example:

Device# no shutdown

Enables the wireless policy profile.

Note

 

Disabling Auto QoS does not reset global radio configurations like CAC and EDCA parameters.

Rollback AutoQoS Configuration (GUI)

Procedure

Step 1

Choose Configuration > Services > QoS.

Step 2

Click Disable AutoQoS.

Step 3

Click Yes to confirm.

Rollback AutoQoS Configuration

Before you begin


Note

AutoQoS MIB attribute does not support the full functionality with service policy. Currently, there is only support for AutoQoS mode. Service policy must be configured manually.

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Device enable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

clear platform software autoqos config template { enterprise_avc | guest}

Example:

Device# clear platform software autoqos config template guest

Resets AutoQoS configuration.

  • enterprise-avc—Resets AutoQoS Enterprise AVC Policy Template.

  • guest—Resets AutoQoS Guest Policy Template.

Clearing Wireless AutoQoS Policy Profile (GUI)

Procedure

Step 1

Choose Configuration > Tags & Profiles > Policy.

Step 2

Click on the Policy Profile Name.

Step 3

Go to QOS and AVC tab.

Step 4

From the Auto Qos drop-down list, choose None.

Step 5

Click Update & Apply to Device.

Clearing Wireless AutoQoS Policy Profile

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Device# enable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

shutdown

Example:

Device# shutdown

Shuts down the policy profile.

Step 3

wireless autoqos policy-profile policy-name mode clear

Example:

Device# wireless autoqos policy-profile test-profile mode clear

Clears the configured AutoQoS wireless policy.

Step 4

[no] shutdown

Example:

no shutdown

Enables the wireless policy profile.

Viewing AutoQoS on policy profile

Before you begin

AutoQoS is supported on the local mode and flex mode. AutoQoS configures a set of policies and radio configurations depending on the template. It is possible to override the service-policy that is configured by AutoQoS. The latest configuration takes effect, with AAA override policy being of highest priority.

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Deviceenable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

show wireless profile policy detailed policy-profile-name

Example:

Device# show wireless profile policy detailed testqos

Shows policy-profile detailed parameters.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco