Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.3.x

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book

Results

Updated:
March 27, 2023

Chapter: LED States for Access Points

LED States for Access Points

Information About LED States for Access Points

In a wireless LAN network where there are a large number of access points, it is difficult to locate a specific access point associated with the controller. You can configure the controller to set the LED state of an access point so that it blinks and the access point can be located. This configuration can be done in the wireless network on a global as well as per-AP level.

The LED state configuration at the global level takes precedence over the AP level.


Note

When disabling the LED on an access point, note that the LED state is controlled by the AP-Join profile on the Cisco 9800 controller. To maintain the LED in a disabled state, it is recommended to create a separate AP-Join profile and Site Tag specifically for APs with the LED disabled.

Configuring LED State in Access Points (GUI)

Procedure

Step 1

Choose Configuration > Wireless > Access Points.

Step 2

Click an AP from the AP list.

The Edit AP window is displayed.

Step 3

In the General tab, under the General section, click the box adjacent to the LED State field to enable or disable the LED state.

Step 4

From the LED Brightness Level drop-down list, choose a value from 1 to 8.

Step 5

Click Update & Apply to Device.

Configuring LED State for Access Points in the Global Configuration Mode (CLI)

Procedure

  Command or Action Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode. Enter your password if prompted.

Step 2

ap name Cisco-AP-name led

Example:

Device# ap name Cisco-AP-name led

Enables the LED state for Cisco APs, globally.

Step 3

ap name Cisco-AP-name led-brightness-level 1-8

Example:

Device# ap name Cisco-AP-name led-brightness-level 4

Configures the LED brightness level. Value of the brightness is from 1 to 8.

Configuring LED State in the AP Profile

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

ap profile default-ap-profile

Example:

Device(config)#ap profile default-ap-profile

Enters the AP profile configuration mode.

Step 3

led

Example:

Device(config-ap-profile)# led

Enables the LED-state for all Cisco APs.

Verifying LED State for Access Points

To verify the LED state of the access points, use the following command:

show ap name AXXX-APXXXX.bdXX.f2XX config general 

Device# show ap name AXXX-APXXXX.bdXX.f2XX config general 
Cisco AP Name : AXXX-APXXXX.bdXX.f2XX 
=================================================
Cisco AP Identifier : 0cXX.bdXX.65XX
Country Code : Multiple Countries : FR,IN,US
Regulatory Domain Allowed by Country : 802.11bg:-AE 802.11a:-ABDEN
AP Country Code : US - United States
AP Regulatory Domain
802.11bg : -A
802.11a : -B
.
.
.
CAPWAP Preferred mode : IPv4
CAPWAP UDP-Lite : Not Configured
AP Submode : WIPS
Office Extend Mode : Disabled
Dhcp Server : Disabled
Remote AP Debug : Disabled
Logging Trap Severity Level : information
Logging Syslog facility : kern
Software Version : 17.X.0.XXX
Boot Version : 1.1.X.X
Mini IOS Version : 0.0.0.0
Stats Reporting Period : 180
LED State : Enabled
MDNS Group Id : 0
.
.
.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco