Wireless Sub-Package for Switch

Introduction to Wireless Sub-package

Wireless-only Fabric uses fabric constructs to garner the benefits of a fabric. In this architecture, a fabric is built on top of existing traditional network designs such as multi-tier, Routed Access, and VSS network. It uses a LISP control plane together with VXLAN encapsulation for the overlay data plane traffic. The wireless control plane remains intact with CAPWAP tunnels initiating on the APs and terminating on a Cisco Catalyst 9800 Series Wireless Controller or AireOS controller. The Cisco Catalyst 9800 Series Wireless Controller can function in a dedicated appliance, directly in a switch, or in a VM.

Cisco Catalyst 9800 Wireless Controller for Switch delivers all the benefits of a centralized control and management plane (easy to configure, upgrade, troubleshoot, etc) and the maximum throughput or performance of a distributed forwarding plane. The distributed data plane allows services such as AVC to scale. In this new model, the wireless control plane is not split between MC and MA. The switch is detached from the wireless control plane and the controller takes care of the wireless function and the traffic switching is done by the Cisco Access Switch.

Since the wireless functionality is required to be enabled only on few nodes of the network, you can install Cisco Catalyst 9800 Series Wireless Controller as a separate package on the switch on a need basis. The sub-package is installed on top of the base image and a reload is required to activate the sub-package.


Note


The sub-package is an optional binary that contains the entire Cisco Catalyst 9800 Series Wireless Controller software.



Note


SNMP is not supported on Catalyst 9800 Embedded Wireless Controller for Switch.


How to Install Wireless Package

  1. Install the base image (without wireless) on the switch.

  2. Install the wireless package on the switch.

  3. Upgrade the AP image.

  4. Reload the switch.

  5. Enable wireless on the switch using the wireless-controller configuration command, and configure wireless features.

How to Remove Wireless Package

  1. Uninstall the wireless package from the switch.

  2. Reload the switch.

  3. Run the write command. This removes the wireless configuration from the startup-configuration.

Upgrading to a Newer Version of Wireless Package

  1. Install the base image (without wireless) on the switch.

  2. Install the updated wireless package.

  3. Reload the switch.

  4. Commit the installation.

Booting in Install Mode

Use the procedure given below to boot the switch in install-mode:

Before you begin

The sub-package does not work in bundle-mode. Use the show version command to verify the boot mode.

Procedure


Step 1

install add file image.bin location activate commit .

This command moves the switch from bundle-mode to install-mode. Note that image.bin is the base image.

Step 2

Click yes to all the prompts.

Step 3

reload

Reloads the switch. Ensure that you boot from flash:packages.conf. After the reload, the switch will be in install-mode.

Note

 

During Install mode image upgrade/downgrade, “Install add file” with flash:<file_name> command is not supported. Instead of that “bootflash:<filename”> needs to be used.

Install add file bootflash:<file_name>  activate commit

What to do next

Verify the boot mode using the show version command.

Installing Sub-Package in a Single Step (GUI)

Procedure


Step 1

Choose Administration > Software Management > Software Upgrade.

Step 2

Choose the upgrade mode from the Upgrade Mode drop-down list, the transport type from the Transport Type drop-down list and enter the Server IP Address (IPv4/IPv6), the File System and choose the location from the Source File Path drop-down list.

Step 3

Click Download & Install.


Installing Sub-Package in a Single Step

Use the procedure given below to install sub-package in a single step:

Before you begin

  • Ensure that the switch is in install-mode.

  • Ensure that you boot only from flash:packages.conf.

Procedure


Step 1

install add file flash:<controller>.bin activate commit

Installs the Cisco Catalyst 9800 Wireless Controller for Switch sub-package.

Note

 

The sub-package (flash:<controller>.bin) is available on www.cisco.com. You can also install the sub-package directly from TFTP server.

Step 2

Click yes to all the prompts.


What to do next

Use the show install summary command to verify the installed image or package.

Multi-step Installation of Sub-Package

Use the procedure given below to install sub-package:

Before you begin

  • Ensure that the switch is in install-mode.

  • Ensure that you boot only from flash:packages.conf.

Procedure


Step 1

install add file flash:<controller>.bin

The sub-package is added to the flash and expanded.

Step 2

install activate file flash:<controller>.bin

Installs the sub-package.

Step 3

install commit

Completes the installation by writing the files.


What to do next

Use the show install summary command to verify the installed image or package.

Installing on a Stack

You can install the package on a stack using either Single-step Package Installation or .

If a new member joins the stack, the two possible scenarios are:

  • If auto-upgrade is enabled: The required software is installed on to the new member. It will match the version of software running on the stack as well as the wireless package.

  • If auto-upgrade is disabled: As the software version is not the same as in the stack, the new member will remain in version mismatch state and it will not join the stack. You have to manually run the install autoupgrade command in EXEC mode to initiate the auto-upgrade procedure.

Upgrading to a Newer Version of Wireless Package

Use the procedure given below to upgrade to a newer version of wireless package:

Procedure


Step 1

install add file flash:<base-image>.bin

The base image (without wireless) is added to the flash and expanded.

Step 2

install add file flash:<controller-sub-package>.bin

The sub-package is added to the flash and expanded.

Step 3

install active

Installs the base image and sub-package and triggers a reload. However, you can also rollback to the previous state after the reload.

Step 4

install commit

Completes the installation by writing the files.


Deactivating the Wireless Package

Follow the procedure given below to deactivate the wireless sub-package:

Procedure

  Command or Action Purpose

Step 1

install deactivate file flash:<controller>.bin

Example:

Device# install deactivate file flash:<controller>.bin

Removes the package and forces the switch to reboot.

Step 2

install commit

Example:

Device# install commit

Commits the switch without wireless package.

Enabling or Disabling Auto-Upgrade

Follow the procedure given below to enable or disable auto-upgrade:

Procedure

  Command or Action Purpose

Step 1

software auto-upgrade enable

Example:

Device(config)# software auto-upgrade enable

Enables software auto-upgrade.

Step 2

no software auto-upgrade enable

Example:

Device(config)# no software auto-upgrade enable

Disables software auto-upgrade.