Supported Hardware Components

This chapter contains information about the supported hardware components on the .

Supported EPA

The following table lists the supported EPA on the Cisco Catalyst CW9800M Wireless Controller .

PID

Description

EPA0

Four 1 GE/10 GE-ports that support small form-factor pluggable (SFP) optical transceivers to provide network connectivity. Ports are numbered 0 – 3.

See the Supported SFP Transceivers section, for supported transceivers.

EPA1

Two 25 GE-ports that support small form-factor pluggable (SFP+) optical transceivers to provide network connectivity. Ports are numbered 0 - 2 in (TE0/1/0, 0/1/1, and 0/1/2 Bay 1)

See the Supported SFP Transceivers section, for supported transceivers.

Supported SFP Models

The following table lists the supported SFP models [25GBASE] on the Cisco Catalyst CW9800M Wireless Controller

Table 1. Supported 25GBASE SFP Models

PID

Description

SFP-25G-SR-S

25GBASE-SR SFP28 Module for MMF

SFP-25G-ER-I

25GBASE-ER, SFP28 Industrial Temperature Module for SMF

SFP-10/25G-LR-I

10/25GBASE-LR Module for SMF

SFP-10/25G-LR-S

10/25GBASE-LR SFP28 Module for SMF

SFP-10/25G-CSR-S

10/25GBASE-CSR SFP28 Module for MMF

SFP-10/25G-BXD-I

10GBASE-LR, 10GBASE-BR10, 25GBASE-BR10 SFP28, Bidirectional, Industrial Temperature Module for SMF

SFP-10/25G-BXU-I

10GBASE-LR, 10GBASE-BR10, 25GBASE-BR10 SFP28, Bidirectional, Industrial Temp Module for SMF

SFP-H25G-CU1M

25GBASE-CR1 Copper Cable 1-meter

SFP-H25G-CU5M

25GBASE-CR1 Copper Cable 5-meter

SFP-25G-AOC1M

25GBASE-AOC Active Optical Cable 1-meter

SFP-25G-AOC2M

25GBASE-AOC Active Optical Cable 2-meter

SFP-25G-AOC3M

25GBASE-AOC Active Optical Cable 3-meter

SFP-25G-AOC5M

25GBASE-AOC Active Optical Cable 5-meter

SFP-25G-AOC7M

25GBASE-AOC Active Optical Cable 7-meter

SFP-25G-AOC10M

25GBASE-AOC Active Optical Cable 10-meter

Supported Transceivers

The Cisco Catalyst CW9800M Wireless Controller supports the following small form-factor pluggable (SFP) transceiver types:

Bay

Ports

Cisco Catalyst CW9800M Wireless Controller

Bay 0

4 X 1 GE/10 GE ports

  • Te0/0/0—1-GE SFP/ 10-GE SFP+ Port 0

  • Te0/0/2—1-GE SFP/ 10-GE SFP+ Port 2

  • Te0/0/1—1-GE SFP/ 10-GE SFP+ Port 1

  • Te0/0/3—1-GE SFP/ 10-GE SFP+ Port 3

SFP

Bay 1

2 X 25 GE ports

  • TwentyFiveGigE0/1/0—25-GE SFP+ Port 0

  • TwentyFiveGigE0/1/1—25-GE SFP+ Port 1

SFP+
Table 2. Supported SFP Transceiver (1000BASE)
PID

Description

GLC-LH-SMD

1000BASE-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM

GLC-SX-MMD

1000BASE-SX SFP transceiver module, MMF, 850nm, DOM

GLC-TE

1000BASE-T SFP transceiver module for category 5 copper wire

GLC-ZX-SMD

1000BASE-ZX SFP transceiver module, SMF, 1550nm, DOM

GLC-BX-U

1000BASE-BX SFP, 1310nm

GLC-BX-D

1000BASE-BX SFP, 1490nm

GLC-EX-SMD

1000BASE-EX SFP, long-wavelength, DOM
Table 3. Supported 10GBASE SFP+ Transceiver

PID

Description

SFP-10G-SR

10-GB-SR SFP+ Module for MMF

SFP-10G-SR-S

10-GB-SR-S SFP+ Module for MMF

SFP-10G-SR-I

10-GB-SR-I SFP+ Module for MMF

SFP-10G-LR

10-GB-LR SFP+ Module for SMF

SFP-10G-LR-X

10-GB-LR SFP+ Module for Extended Temp range

SFP-10G-ER

10-GB-ER SFP+ Module for SMF

SFP-10G-ZR-I

10-BG-ZR-I SFP+ Module for industrial operating temperature

SFP-10G-T-X

10-GB-T Module with SFP+ form factor and an RJ-45 interface

SFP-10G-AOC1M

10-GB SFP+ model for AOC1M

SFP-10G-AOC2M

10-GB SFP+ model for AOC2M

SFP-10G-AOC3M

10-GB SFP+ model for AOC3M

SFP-10G-AOC5M

10-GB SFP+ model for AOC5M

SFP-10G-AOC7M

10-GB SFP+ model for AOC7M

SFP-H10GB-ACU7M

10-GB-CU SFP+ Cable 7 Meter, active

SFP-H10GB-ACU10M

10-GB-CU SFP+ Cable 10 Meter, active

SFP-H10GB-CU1M

10-GB SFP+ model for CU1M

SFP-H10GB-CU2M

10-GB SFP+ model for CU2M

SFP-H10GB-CU3M

10-GB SFP+ model for CU3M

SFP-H10GB-CU5M

10-GB SFP+ model for CU5M

SFP-H10GB-CU1-5M

10-GB SFP+ model for CU1-5M

SFP-H10GB-CU12-5M

10-GB SFP+ model for CU2-5M

Finisar-LR (FTLX1471D3BCL)

10-GB- LR-SFP+ Module for MMF

Finisar-SR (FTLX8574D3BC)

10-GB-SR SFP+ Module for MMF

For more information about the supported SFP+ transceivers, see the datasheet at https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9800-series-wireless-controllers/nb-06-cat9800-wirel-cont-data-sheet-ctp-en.html

Power Supplies

The Cisco Catalyst CW9800M Wireless Controller supports one AC power supply always with a blank cover, or two AC power supplies. The modular chassis configurations support the installation of two power supplies for redundancy. When a power supply fails or is removed, the other power supply provides power requirements for the chassis. This allows you to hot-swap the power supply without impacting the functionality of the controller.

The power supplies are used in a 1 + 1 redundant configuration. There is no input switch on the faceplate of the power supplies. A power supply is switched from Standby to On by way of a system chassis power switch.

The following table lists the power supplies that you can order:

Part Number

Power Supply

PWR-CH1-750WACR

Cisco Catalyst CW9800M Wireless Controller power supply module 750W AC Power


Note
Platform related information can be obtained through a programmable interface using openconfig-platform model. However, power auditing per component is not supported.

Power Supply LEDs

The following table describes the power supply LEDs:

Table 4. AC/DC Power Supply LEDs

Power Supply Condition

Green (OK) LED Status

Amber (FAIL) LED Status

No AC power to all power supplies

OFF

OFF

Power Supply Failure (includes over voltage, over current, over temperature and fan failure)

OFF

ON

Power Supply Warning events where the power supply continues to operate (high temperature, high power and slow fan)

OFF

1 Hz Blinking

AC Present/12VSB on (PSU OFF)

1 Hz Blinking

OFF

Power Supply ON and OK

ON

OFF

Power Supply Fans

The fans in the power supply module are used for cooling the power supply module itself while a system-level cooling is provided by fans within the chassis. The power supplies do not depend on the system-level fans for cooling. Fan-rotation sensors determine the fan failures


Note
The fans in the Cisco Catalyst CW9800M Wireless Controller power supplies have plug-side exhaust airflow.

Caution
The chassis has a front-to-rear airflow. All power supplies and fan modules in the same chassis must use the same airflow direction or an error will occur with possible overheating and shut down of the controller.

If you power up the controller with more than one airflow direction, you must power down the controller and replace the modules with the wrong airflow direction before powering up the controller.


Note
The fans in the power supply modules run when the power supply is plugged in, even if the power switch is in the standby position.